diff --git a/Marlin/boards.h b/Marlin/boards.h
index 1a5acaa153..c6997fe87b 100644
--- a/Marlin/boards.h
+++ b/Marlin/boards.h
@@ -49,6 +49,7 @@
#define BOARD_5DPRINT 88 // 5DPrint D8 Driver Board
#define BOARD_LEAPFROG 999 // Leapfrog
#define BOARD_WITBOX 41 // bq WITBOX
+#define BOARD_HEPHESTOS 42 // bq Prusa i3 Hephestos
#define BOARD_99 99 // This is in pins.h but...?
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
new file mode 100644
index 0000000000..4694afd453
--- /dev/null
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -0,0 +1,808 @@
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+
+#include "boards.h"
+
+// This configuration file contains the basic settings.
+// Advanced settings can be found in Configuration_adv.h
+// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/delta directory.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_VERSION "1.0.2"
+#define STRING_URL "reprap.org"
+#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
+#define STRING_CONFIG_H_AUTHOR "(bq Hephestos)" // Who made the changes.
+#define STRING_SPLASH "v" STRING_VERSION " - " STRING_URL // will be shown during bootup
+
+// SERIAL_PORT selects which serial port should be used for communication with the host.
+// This allows the connection of wireless adapters (for instance) to non-default port pins.
+// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
+#define SERIAL_PORT 0
+
+// This determines the communication speed of the printer
+#define BAUDRATE 115200
+
+// This enables the serial port associated to the Bluetooth interface
+//#define BTENABLED // Enable BT interface on AT90USB devices
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+ #define MOTHERBOARD BOARD_HEPHESTOS
+#endif
+
+// Define this to set a custom name for your generic Mendel,
+// #define CUSTOM_MENDEL_NAME "This Mendel"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// This defines the number of extruders
+#define EXTRUDERS 1
+
+//// The following define selects which power supply you have. Please choose the one that matches your setup
+// 1 = ATX
+// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+
+#define POWER_SUPPLY 1
+
+// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
+// #define PS_DEFAULT_OFF
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+// (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 110 is Pt100 with 1k pullup (non standard)
+
+#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_BED 0
+
+// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Actual temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 10 // (seconds)
+#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 260
+#define HEATER_1_MAXTEMP 260
+#define HEATER_2_MAXTEMP 260
+#define BED_MAXTEMP 150
+
+// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
+// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
+// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
+//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
+
+// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
+//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
+//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
+
+// PID settings:
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#ifdef PIDTEMP
+ //#define PID_DEBUG // Sends debug data to the serial port.
+ //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+ //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+ //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+ // Set/get with gcode: M301 E[extruder number, 0-2]
+ #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+ // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+ #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
+ #define K1 0.95 //smoothing factor within the PID
+ #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
+
+// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+// Ultimaker
+// #define DEFAULT_Kp 22.2
+// #define DEFAULT_Ki 1.08
+// #define DEFAULT_Kd 114
+
+// MakerGear
+// #define DEFAULT_Kp 7.0
+// #define DEFAULT_Ki 0.1
+// #define DEFAULT_Kd 12
+
+// Mendel Parts V9 on 12V
+// #define DEFAULT_Kp 63.0
+// #define DEFAULT_Ki 2.25
+// #define DEFAULT_Kd 440
+
+// Hephestos (i3)
+ #define DEFAULT_Kp 23.05
+ #define DEFAULT_Ki 2.00
+ #define DEFAULT_Kd 66.47
+
+#endif // PIDTEMP
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+ #define DEFAULT_bedKp 10.00
+ #define DEFAULT_bedKi .023
+ #define DEFAULT_bedKd 305.4
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+// #define DEFAULT_bedKp 97.1
+// #define DEFAULT_bedKi 1.41
+// #define DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+
+//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
+//can be software-disabled for whatever purposes by
+#define PREVENT_DANGEROUS_EXTRUDE
+//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
+#define PREVENT_LENGTHY_EXTRUDE
+
+#define EXTRUDE_MINTEMP 170
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+
+/*================== Thermal Runaway Protection ==============================
+This is a feature to protect your printer from burn up in flames if it has
+a thermistor coming off place (this happened to a friend of mine recently and
+motivated me writing this feature).
+
+The issue: If a thermistor come off, it will read a lower temperature than actual.
+The system will turn the heater on forever, burning up the filament and anything
+else around.
+
+After the temperature reaches the target for the first time, this feature will
+start measuring for how long the current temperature stays below the target
+minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
+
+If it stays longer than _PERIOD, it means the thermistor temperature
+cannot catch up with the target, so something *may be* wrong. Then, to be on the
+safe side, the system will he halt.
+
+Bear in mind the count down will just start AFTER the first time the
+thermistor temperature is over the target, so you will have no problem if
+your extruder heater takes 2 minutes to hit the target on heating.
+
+*/
+// If you want to enable this feature for all your extruder heaters,
+// uncomment the 2 defines below:
+
+// Parameters for all extruder heaters
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
+
+// If you want to enable this feature for your bed heater,
+// uncomment the 2 defines below:
+
+// Parameters for the bed heater
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
+//===========================================================================
+
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+// Uncomment the following line to enable CoreXY kinematics
+// #define COREXY
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#ifndef ENDSTOPPULLUPS
+ // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+ // #define ENDSTOPPULLUP_XMAX
+ // #define ENDSTOPPULLUP_YMAX
+ // #define ENDSTOPPULLUP_ZMAX
+ // #define ENDSTOPPULLUP_XMIN
+ // #define ENDSTOPPULLUP_YMIN
+ // #define ENDSTOPPULLUP_ZMIN
+#endif
+
+#ifdef ENDSTOPPULLUPS
+ #define ENDSTOPPULLUP_XMAX
+ #define ENDSTOPPULLUP_YMAX
+ #define ENDSTOPPULLUP_ZMAX
+ #define ENDSTOPPULLUP_XMIN
+ #define ENDSTOPPULLUP_YMIN
+ #define ENDSTOPPULLUP_ZMIN
+#endif
+
+// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+//#define DISABLE_MAX_ENDSTOPS
+//#define DISABLE_MIN_ENDSTOPS
+
+// Disable max endstops for compatibility with endstop checking routine
+#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
+ #define DISABLE_MAX_ENDSTOPS
+#endif
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis when it's not being used.
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
+
+#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
+#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
+#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
+
+// ENDSTOP SETTINGS:
+// Sets direction of endstops when homing; 1=MAX, -1=MIN
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
+#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
+
+// Travel limits after homing
+#define X_MAX_POS 215
+#define X_MIN_POS 0
+#define Y_MAX_POS 210
+#define Y_MIN_POS 0
+#define Z_MAX_POS 180
+#define Z_MIN_POS 0
+
+#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
+#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
+#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+//============================= Bed Auto Leveling ===========================
+
+//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
+#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#ifdef ENABLE_AUTO_BED_LEVELING
+
+// There are 2 different ways to pick the X and Y locations to probe:
+
+// - "grid" mode
+// Probe every point in a rectangular grid
+// You must specify the rectangle, and the density of sample points
+// This mode is preferred because there are more measurements.
+// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+
+// - "3-point" mode
+// Probe 3 arbitrary points on the bed (that aren't colinear)
+// You must specify the X & Y coordinates of all 3 points
+
+ #define AUTO_BED_LEVELING_GRID
+ // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
+ // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
+ // and least squares solution is calculated
+ // Note: this feature occupies 10'206 byte
+ #ifdef AUTO_BED_LEVELING_GRID
+
+ // set the rectangle in which to probe
+ #define LEFT_PROBE_BED_POSITION 15
+ #define RIGHT_PROBE_BED_POSITION 170
+ #define BACK_PROBE_BED_POSITION 180
+ #define FRONT_PROBE_BED_POSITION 20
+
+ // set the number of grid points per dimension
+ // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
+ #define AUTO_BED_LEVELING_GRID_POINTS 2
+
+
+ #else // not AUTO_BED_LEVELING_GRID
+ // with no grid, just probe 3 arbitrary points. A simple cross-product
+ // is used to esimate the plane of the print bed
+
+ #define ABL_PROBE_PT_1_X 15
+ #define ABL_PROBE_PT_1_Y 180
+ #define ABL_PROBE_PT_2_X 15
+ #define ABL_PROBE_PT_2_Y 20
+ #define ABL_PROBE_PT_3_X 170
+ #define ABL_PROBE_PT_3_Y 20
+
+ #endif // AUTO_BED_LEVELING_GRID
+
+
+ // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
+ // X and Y offsets must be integers
+ #define X_PROBE_OFFSET_FROM_EXTRUDER -25
+ #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
+ #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
+
+ #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
+ // Be sure you have this distance over your Z_MAX_POS in case
+
+ #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min
+
+ #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
+ #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
+
+ //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+ //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+ //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
+ //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
+ // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
+
+// #define PROBE_SERVO_DEACTIVATION_DELAY 300
+
+
+//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
+//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+
+ #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
+ // When defined, it will:
+ // - Allow Z homing only after X and Y homing AND stepper drivers still enabled
+ // - If stepper drivers timeout, it will need X and Y homing again before Z homing
+ // - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
+ // - Block Z homing only when the probe is outside bed area.
+
+ #ifdef Z_SAFE_HOMING
+
+ #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28)
+ #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28)
+
+ #endif
+
+ #ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
+ #if X_PROBE_OFFSET_FROM_EXTRUDER < 0
+ #if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+ #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+ #endif
+ #else
+ #if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
+ #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+ #endif
+ #endif
+ #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
+ #if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+ #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+ #endif
+ #else
+ #if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
+ #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
+ #endif
+ #endif
+
+
+ #endif
+
+#endif // ENABLE_AUTO_BED_LEVELING
+
+
+// The position of the homing switches
+//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
+//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
+
+//Manual homing switch locations:
+// For deltabots this means top and center of the Cartesian print volume.
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS 0
+#define MANUAL_Z_HOME_POS 0
+//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+
+//// MOVEMENT SETTINGS
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {2000, 2000, 150, 0} // set the homing speeds (mm/min)
+
+// default settings
+
+#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,100.47095761381482} // default steps per unit for Ultimaker
+#define DEFAULT_MAX_FEEDRATE {250, 250, 3.3, 25} // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
+
+// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
+#define DEFAULT_XYJERK 10.0 // (mm/sec)
+#define DEFAULT_ZJERK 0.4 // (mm/sec)
+#define DEFAULT_EJERK 5.0 // (mm/sec)
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+// Custom M code points
+#define CUSTOM_M_CODES
+#ifdef CUSTOM_M_CODES
+ #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
+ #define Z_PROBE_OFFSET_RANGE_MIN -15
+ #define Z_PROBE_OFFSET_RANGE_MAX -5
+#endif
+
+
+// EEPROM
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
+//define this to enable EEPROM support
+//#define EEPROM_SETTINGS
+//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+// please keep turned on if you can.
+//#define EEPROM_CHITCHAT
+
+// Preheat Constants
+#define PLA_PREHEAT_HOTEND_TEMP 200
+#define PLA_PREHEAT_HPB_TEMP 0
+#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
+
+#define ABS_PREHEAT_HOTEND_TEMP 220
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
+
+//LCD and SD support
+
+// Character based displays can have different extended charsets. If you see strange or missing characters on yours - try an other definition below.
+#define DISPLAY_CHARSET_HD44870_JAPAN // "ääööüüß°"
+//#define DISPLAY_CHARSET_HD44870_WESTERN // with better support for European languages. "ÄäÖöÜüß°"
+//#define DISPLAY_CHARSET_DOGM // for full graphics display "ÄäÖÖÜÜß°"
+
+#define ULTRA_LCD //general LCD support, also 16x2
+//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
+#define SDSUPPORT // Enable SD Card Support in Hardware Console
+//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
+//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
+//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
+//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
+//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
+#define ULTIPANEL //the UltiPanel as on Thingiverse
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+
+// The MaKr3d Makr-Panel with graphic controller and SD support
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//#define MAKRPANEL
+
+// The RepRapDiscount Smart Controller (white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+// The GADGETS3D G3D LCD/SD Controller (blue PCB)
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//#define G3D_PANEL
+
+// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
+
+// The Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//#define RA_CONTROL_PANEL
+
+//automatic expansion
+#if defined (MAKRPANEL)
+ #define DOGLCD
+ #define SDSUPPORT
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define DEFAULT_LCD_CONTRAST 17
+#endif
+
+#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define DOGLCD
+ #define U8GLIB_ST7920
+ #define REPRAP_DISCOUNT_SMART_CONTROLLER
+#endif
+
+#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+#endif
+
+#if defined(REPRAPWORLD_KEYPAD)
+ #define NEWPANEL
+ #define ULTIPANEL
+#endif
+#if defined(RA_CONTROL_PANEL)
+ #define ULTIPANEL
+ #define NEWPANEL
+ #define LCD_I2C_TYPE_PCA8574
+ #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
+#endif
+
+//I2C PANELS
+
+//#define LCD_I2C_SAINSMART_YWROBOT
+#ifdef LCD_I2C_SAINSMART_YWROBOT
+ // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
+ // Make sure it is placed in the Arduino libraries directory.
+ #define LCD_I2C_TYPE_PCF8575
+ #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
+ #define NEWPANEL
+ #define ULTIPANEL
+#endif
+
+// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
+//#define LCD_I2C_PANELOLU2
+#ifdef LCD_I2C_PANELOLU2
+ // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+ // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+ // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
+ // Note: The PANELOLU2 encoder click input can either be directly connected to a pin
+ // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+ #define LCD_I2C_TYPE_MCP23017
+ #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+ #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
+ #define NEWPANEL
+ #define ULTIPANEL
+
+ #ifndef ENCODER_PULSES_PER_STEP
+ #define ENCODER_PULSES_PER_STEP 4
+ #endif
+
+ #ifndef ENCODER_STEPS_PER_MENU_ITEM
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #endif
+
+
+ #ifdef LCD_USE_I2C_BUZZER
+ #define LCD_FEEDBACK_FREQUENCY_HZ 1000
+ #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+ #endif
+
+#endif
+
+// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
+//#define LCD_I2C_VIKI
+#ifdef LCD_I2C_VIKI
+ // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+ // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+ // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+ // BTN_ENC pin (or set BTN_ENC to -1 if not used)
+ #define LCD_I2C_TYPE_MCP23017
+ #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
+ #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
+ #define NEWPANEL
+ #define ULTIPANEL
+#endif
+
+// Shift register panels
+// ---------------------
+// 2 wire Non-latching LCD SR from:
+// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
+
+//#define SAV_3DLCD
+#ifdef SAV_3DLCD
+ #define SR_LCD_2W_NL // Non latching 2 wire shiftregister
+ #define NEWPANEL
+ #define ULTIPANEL
+#endif
+
+
+#ifdef ULTIPANEL
+// #define NEWPANEL //enable this if you have a click-encoder panel
+ #define SDSUPPORT
+ #define ULTRA_LCD
+ #ifdef DOGLCD // Change number of lines to match the DOG graphic display
+ #define LCD_WIDTH 20
+ #define LCD_HEIGHT 5
+ #else
+ #define LCD_WIDTH 20
+ #define LCD_HEIGHT 4
+ #endif
+#else //no panel but just LCD
+ #ifdef ULTRA_LCD
+ #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
+ #define LCD_WIDTH 20
+ #define LCD_HEIGHT 5
+ #else
+ #define LCD_WIDTH 16
+ #define LCD_HEIGHT 2
+ #endif
+ #endif
+#endif
+
+// default LCD contrast for dogm-like LCD displays
+#ifdef DOGLCD
+# ifndef DEFAULT_LCD_CONTRAST
+# define DEFAULT_LCD_CONTRAST 32
+# endif
+#endif
+
+// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Temperature status LEDs that display the hotend and bet temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// M240 Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+// #define PHOTOGRAPH_PIN 23
+
+// SF send wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+//define BlinkM/CyzRgb Support
+//#define BLINKM
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Servo Endstops
+//
+// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
+// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
+//
+//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
+//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
+
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs at slicing)
+ * Single extruder only at this point (extruder 0)
+ *
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
+#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
+#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
+#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
+
+//defines used in the code
+#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
+
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
+
+
+
+
+
+
+#include "Configuration_adv.h"
+#include "thermistortables.h"
+
+#endif //__CONFIGURATION_H
diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h
new file mode 100644
index 0000000000..333396772d
--- /dev/null
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@@ -0,0 +1,535 @@
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+
+#ifdef BED_LIMIT_SWITCHING
+ #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+#endif
+#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
+
+//// Heating sanity check:
+// This waits for the watch period in milliseconds whenever an M104 or M109 increases the target temperature
+// If the temperature has not increased at the end of that period, the target temperature is set to zero.
+// It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature
+// differ by at least 2x WATCH_TEMP_INCREASE
+//#define WATCH_TEMP_PERIOD 40000 //40 seconds
+//#define WATCH_TEMP_INCREASE 10 //Heat up at least 10 degree in 20 seconds
+
+#ifdef PIDTEMP
+ // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
+ // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ #define PID_ADD_EXTRUSION_RATE
+ #ifdef PID_ADD_EXTRUSION_RATE
+ #define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
+ #endif
+#endif
+
+
+//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
+//The maximum buffered steps/sec of the extruder motor are called "se".
+//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
+// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
+// you exit the value by any M109 without F*
+// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
+// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+#define AUTOTEMP
+#ifdef AUTOTEMP
+ #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+//Show Temperature ADC value
+//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
+// extruder run-out prevention.
+//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
+//#define EXTRUDER_RUNOUT_PREVENT
+#define EXTRUDER_RUNOUT_MINTEMP 190
+#define EXTRUDER_RUNOUT_SECONDS 30.
+#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
+#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
+#define EXTRUDER_RUNOUT_EXTRUDE 100
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN 1.0
+
+//This is for controlling a fan to cool down the stepper drivers
+//it will turn on when any driver is enabled
+//and turn off after the set amount of seconds from last driver being disabled again
+#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
+#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
+#define CONTROLLERFAN_SPEED 255 // == full speed
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds. This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+//#define FAN_KICKSTART_TIME 100
+
+// Extruder cooling fans
+// Configure fan pin outputs to automatically turn on/off when the associated
+// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
+// Multiple extruders can be assigned to the same pin in which case
+// the fan will turn on when any selected extruder is above the threshold.
+#define EXTRUDER_0_AUTO_FAN_PIN -1
+#define EXTRUDER_1_AUTO_FAN_PIN -1
+#define EXTRUDER_2_AUTO_FAN_PIN -1
+#define EXTRUDER_3_AUTO_FAN_PIN -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
+
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+//#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
+
+
+//// AUTOSET LOCATIONS OF LIMIT SWITCHES
+//// Added by ZetaPhoenix 09-15-2012
+#ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations
+ #define X_HOME_POS MANUAL_X_HOME_POS
+ #define Y_HOME_POS MANUAL_Y_HOME_POS
+ #define Z_HOME_POS MANUAL_Z_HOME_POS
+#else //Set min/max homing switch positions based upon homing direction and min/max travel limits
+ //X axis
+ #if X_HOME_DIR == -1
+ #ifdef BED_CENTER_AT_0_0
+ #define X_HOME_POS X_MAX_LENGTH * -0.5
+ #else
+ #define X_HOME_POS X_MIN_POS
+ #endif //BED_CENTER_AT_0_0
+ #else
+ #ifdef BED_CENTER_AT_0_0
+ #define X_HOME_POS X_MAX_LENGTH * 0.5
+ #else
+ #define X_HOME_POS X_MAX_POS
+ #endif //BED_CENTER_AT_0_0
+ #endif //X_HOME_DIR == -1
+
+ //Y axis
+ #if Y_HOME_DIR == -1
+ #ifdef BED_CENTER_AT_0_0
+ #define Y_HOME_POS Y_MAX_LENGTH * -0.5
+ #else
+ #define Y_HOME_POS Y_MIN_POS
+ #endif //BED_CENTER_AT_0_0
+ #else
+ #ifdef BED_CENTER_AT_0_0
+ #define Y_HOME_POS Y_MAX_LENGTH * 0.5
+ #else
+ #define Y_HOME_POS Y_MAX_POS
+ #endif //BED_CENTER_AT_0_0
+ #endif //Y_HOME_DIR == -1
+
+ // Z axis
+ #if Z_HOME_DIR == -1 //BED_CENTER_AT_0_0 not used
+ #define Z_HOME_POS Z_MIN_POS
+ #else
+ #define Z_HOME_POS Z_MAX_POS
+ #endif //Z_HOME_DIR == -1
+#endif //End auto min/max positions
+//END AUTOSET LOCATIONS OF LIMIT SWITCHES -ZP
+
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
+// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
+// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
+// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
+//#define Z_DUAL_STEPPER_DRIVERS
+
+#ifdef Z_DUAL_STEPPER_DRIVERS
+ #undef EXTRUDERS
+ #define EXTRUDERS 1
+#endif
+
+// Same again but for Y Axis.
+//#define Y_DUAL_STEPPER_DRIVERS
+
+// Define if the two Y drives need to rotate in opposite directions
+#define INVERT_Y2_VS_Y_DIR true
+
+#ifdef Y_DUAL_STEPPER_DRIVERS
+ #undef EXTRUDERS
+ #define EXTRUDERS 1
+#endif
+
+#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
+ #error "You cannot have dual drivers for both Y and Z"
+#endif
+
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds.
+//#define DUAL_X_CARRIAGE
+#ifdef DUAL_X_CARRIAGE
+// Configuration for second X-carriage
+// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+// the second x-carriage always homes to the maximum endstop.
+#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
+#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
+#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+ // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
+ // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+ // without modifying the firmware (through the "M218 T1 X???" command).
+ // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
+#define X2_ENABLE_PIN 29
+#define X2_STEP_PIN 25
+#define X2_DIR_PIN 23
+
+// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
+// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+// as long as it supports dual x-carriages. (M605 S0)
+// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+// that additional slicer support is not required. (M605 S1)
+// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
+// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+
+// This is the default power-up mode which can be later using M605.
+#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
+
+// Default settings in "Auto-park Mode"
+#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
+#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
+
+// Default x offset in duplication mode (typically set to half print bed width)
+#define DEFAULT_DUPLICATION_X_OFFSET 100
+
+#endif //DUAL_X_CARRIAGE
+
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_RETRACT_MM 5
+#define Y_HOME_RETRACT_MM 5
+#define Z_HOME_RETRACT_MM 2
+//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+#ifdef CONFIG_STEPPERS_TOSHIBA
+#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
+#else
+#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
+#endif
+//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+//default stepper release if idle
+#define DEFAULT_STEPPER_DEACTIVE_TIME 60
+
+#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE 0.0
+
+// Feedrates for manual moves along X, Y, Z, E from panel
+#ifdef ULTIPANEL
+#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // set the speeds for manual moves (mm/min)
+#endif
+
+//Comment to disable setting feedrate multiplier via encoder
+#ifdef ULTIPANEL
+ #define ULTIPANEL_FEEDMULTIPLY
+#endif
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME 20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT 15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
+
+// MS1 MS2 Stepper Driver Microstepping mode table
+#define MICROSTEP1 LOW,LOW
+#define MICROSTEP2 HIGH,LOW
+#define MICROSTEP4 LOW,HIGH
+#define MICROSTEP8 HIGH,HIGH
+#define MICROSTEP16 HIGH,HIGH
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
+
+// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+
+// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
+//#define DIGIPOT_I2C
+// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
+#define DIGIPOT_I2C_NUM_CHANNELS 8
+// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
+#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
+#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
+#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
+// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
+// using:
+#define MENU_ADDAUTOSTART
+
+// Show a progress bar on HD44780 LCDs for SD printing
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+ // Amount of time (ms) to show the bar
+ #define PROGRESS_BAR_BAR_TIME 2000
+ // Amount of time (ms) to show the status message
+ #define PROGRESS_BAR_MSG_TIME 3000
+ // Amount of time (ms) to retain the status message (0=forever)
+ #define PROGRESS_MSG_EXPIRE 0
+ // Enable this to show messages for MSG_TIME then hide them
+ //#define PROGRESS_MSG_ONCE
+ #ifdef DOGLCD
+ #warning LCD_PROGRESS_BAR does not apply to graphical displays at this time.
+ #endif
+ #ifdef FILAMENT_LCD_DISPLAY
+ #error LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both.
+ #endif
+#endif
+
+// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
+//#define USE_WATCHDOG
+
+#ifdef USE_WATCHDOG
+// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+//#define WATCHDOG_RESET_MANUAL
+#endif
+
+// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
+//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
+// it can e.g. be used to change z-positions in the print startup phase in real-time
+// does not respect endstops!
+//#define BABYSTEPPING
+#ifdef BABYSTEPPING
+ #define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
+ #define BABYSTEP_INVERT_Z false //true for inverse movements in Z
+ #define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements
+
+ #ifdef COREXY
+ #error BABYSTEPPING not implemented for COREXY yet.
+ #endif
+
+ #ifdef DELTA
+ #ifdef BABYSTEP_XY
+ #error BABYSTEPPING only implemented for Z axis on deltabots.
+ #endif
+ #endif
+#endif
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// Hooke's law says: force = k * distance
+// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#ifdef ADVANCE
+ #define EXTRUDER_ADVANCE_K .0
+
+ #define D_FILAMENT 1.75
+ #define STEPS_MM_E 100.47095761381482
+ #define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
+ #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUSION_AREA)
+
+#endif // ADVANCE
+
+// Arc interpretation settings:
+#define MM_PER_ARC_SEGMENT 1
+#define N_ARC_CORRECTION 25
+
+const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
+
+// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
+// be commented out otherwise
+#define SDCARDDETECTINVERTED
+
+#ifdef ULTIPANEL
+ #undef SDCARDDETECTINVERTED
+#endif
+
+// Power Signal Control Definitions
+// By default use ATX definition
+#ifndef POWER_SUPPLY
+ #define POWER_SUPPLY 1
+#endif
+// 1 = ATX
+#if (POWER_SUPPLY == 1)
+ #define PS_ON_AWAKE LOW
+ #define PS_ON_ASLEEP HIGH
+#endif
+// 2 = X-Box 360 203W
+#if (POWER_SUPPLY == 2)
+ #define PS_ON_AWAKE HIGH
+ #define PS_ON_ASLEEP LOW
+#endif
+
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
+//===========================================================================
+//=============================Buffers ============================
+//===========================================================================
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
+#if defined SDSUPPORT
+ #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+ #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+
+//The ASCII buffer for receiving from the serial:
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 5
+
+
+// Firmware based and LCD controlled retract
+// M207 and M208 can be used to define parameters for the retraction.
+// The retraction can be called by the slicer using G10 and G11
+// until then, intended retractions can be detected by moves that only extrude and the direction.
+// the moves are than replaced by the firmware controlled ones.
+
+// #define FWRETRACT //ONLY PARTIALLY TESTED
+#ifdef FWRETRACT
+ #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
+ #define RETRACT_LENGTH 3 //default retract length (positive mm)
+ #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
+ #define RETRACT_FEEDRATE 80*60 //default feedrate for retracting (mm/s)
+ #define RETRACT_ZLIFT 0 //default retract Z-lift
+ #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
+ //#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
+ #define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s)
+#endif
+
+//adds support for experimental filament exchange support M600; requires display
+#ifdef ULTIPANEL
+ #define FILAMENTCHANGEENABLE
+ #ifdef FILAMENTCHANGEENABLE
+ #define FILAMENTCHANGE_XPOS 3
+ #define FILAMENTCHANGE_YPOS 3
+ #define FILAMENTCHANGE_ZADD 10
+ #define FILAMENTCHANGE_FIRSTRETRACT -2
+ #define FILAMENTCHANGE_FINALRETRACT -100
+ #endif
+#endif
+
+#ifdef FILAMENTCHANGEENABLE
+ #ifdef EXTRUDER_RUNOUT_PREVENT
+ #error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE
+ #endif
+#endif
+
+//===========================================================================
+//============================= Define Defines ============================
+//===========================================================================
+
+#if defined (ENABLE_AUTO_BED_LEVELING) && defined (DELTA)
+ #error "Bed Auto Leveling is still not compatible with Delta Kinematics."
+#endif
+
+#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
+ #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
+#endif
+
+#if EXTRUDERS > 1 && defined HEATERS_PARALLEL
+ #error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1"
+#endif
+
+#if TEMP_SENSOR_0 > 0
+ #define THERMISTORHEATER_0 TEMP_SENSOR_0
+ #define HEATER_0_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_1 > 0
+ #define THERMISTORHEATER_1 TEMP_SENSOR_1
+ #define HEATER_1_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_2 > 0
+ #define THERMISTORHEATER_2 TEMP_SENSOR_2
+ #define HEATER_2_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_3 > 0
+ #define THERMISTORHEATER_3 TEMP_SENSOR_3
+ #define HEATER_3_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_BED > 0
+ #define THERMISTORBED TEMP_SENSOR_BED
+ #define BED_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_0 == -1
+ #define HEATER_0_USES_AD595
+#endif
+#if TEMP_SENSOR_1 == -1
+ #define HEATER_1_USES_AD595
+#endif
+#if TEMP_SENSOR_2 == -1
+ #define HEATER_2_USES_AD595
+#endif
+#if TEMP_SENSOR_3 == -1
+ #define HEATER_3_USES_AD595
+#endif
+#if TEMP_SENSOR_BED == -1
+ #define BED_USES_AD595
+#endif
+#if TEMP_SENSOR_0 == -2
+ #define HEATER_0_USES_MAX6675
+#endif
+#if TEMP_SENSOR_0 == 0
+ #undef HEATER_0_MINTEMP
+ #undef HEATER_0_MAXTEMP
+#endif
+#if TEMP_SENSOR_1 == 0
+ #undef HEATER_1_MINTEMP
+ #undef HEATER_1_MAXTEMP
+#endif
+#if TEMP_SENSOR_2 == 0
+ #undef HEATER_2_MINTEMP
+ #undef HEATER_2_MAXTEMP
+#endif
+#if TEMP_SENSOR_3 == 0
+ #undef HEATER_3_MINTEMP
+ #undef HEATER_3_MAXTEMP
+#endif
+#if TEMP_SENSOR_BED == 0
+ #undef BED_MINTEMP
+ #undef BED_MAXTEMP
+#endif
+
+
+#endif //__CONFIGURATION_ADV_H
diff --git a/Marlin/language.h b/Marlin/language.h
index defe1e959d..284c71f7da 100644
--- a/Marlin/language.h
+++ b/Marlin/language.h
@@ -56,17 +56,18 @@
#elif MB(WITBOX)
#define MACHINE_NAME "WITBOX"
#define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
+#elif MB(HEPHESTOS)
+ #define MACHINE_NAME "Hephestos"
+ #define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
#else
- #ifdef CUSTOM_MENDEL_NAME
- #define MACHINE_NAME CUSTOM_MENDEL_NAME
- #else
- #define MACHINE_NAME "Mendel"
- #endif
-
-// Default firmware set to Mendel
+ // Default firmware set to Mendel
+ #define MACHINE_NAME "Mendel"
#define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
#endif
+#ifdef CUSTOM_MENDEL_NAME
+ #define MACHINE_NAME CUSTOM_MENDEL_NAME
+#else
#ifndef MACHINE_UUID
#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
diff --git a/Marlin/pins.h b/Marlin/pins.h
index a89a1f0688..ea8f96c48b 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -108,6 +108,8 @@
#include "pins_LEAPFROG.h"
#elif MB(WITBOX)
#include "pins_WITBOX.h"
+#elif MB(HEPHESTOS)
+ #include "pins_HEPHESTOS.h"
#elif MB(99)
#include "pins_99.h"
#else
diff --git a/Marlin/pins_HEPHESTOS.h b/Marlin/pins_HEPHESTOS.h
new file mode 100644
index 0000000000..c5b7bcf799
--- /dev/null
+++ b/Marlin/pins_HEPHESTOS.h
@@ -0,0 +1,5 @@
+/**
+ * bq Prusa i3 Hephestos – Arduino Mega with RAMPS v1.3/1.4 pin assignments
+ */
+
+#include "pins_RAMPS_13.h"
diff --git a/Marlin/pins_RAMPS_13.h b/Marlin/pins_RAMPS_13.h
index 8990f166d1..e2f74fc834 100644
--- a/Marlin/pins_RAMPS_13.h
+++ b/Marlin/pins_RAMPS_13.h
@@ -63,7 +63,7 @@
#define FILWIDTH_PIN 5
#endif
-#if MB(RAMPS_13_EFB) || MB(RAMPS_13_EFF) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) || MB(WITBOX)
+#if MB(RAMPS_13_EFB) || MB(RAMPS_13_EFF) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) || MB(WITBOX) || MB(HEPHESTOS)
#define FAN_PIN 9 // (Sprinter config)
#if MB(RAMPS_13_EFF)
#define CONTROLLERFAN_PIN -1 // Pin used for the fan to cool controller
@@ -88,7 +88,7 @@
#define HEATER_0_PIN 10 // EXTRUDER 1
#endif
-#if MB(RAMPS_13_EFB) || MB(AZTEEG_X3) || MB(WITBOX)
+#if MB(RAMPS_13_EFB) || MB(AZTEEG_X3) || MB(WITBOX) || MB(HEPHESTOS)
#define HEATER_1_PIN -1
#else
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)