diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
index 665ff45b31..29659feb81 100644
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@@ -279,7 +279,7 @@
/**
* Auto Bed Leveling
*/
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
// Boundaries for probing based on set limits
#define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
@@ -287,7 +287,7 @@
#define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#endif
- #define SERVO_LEVELING (defined(ENABLE_AUTO_BED_LEVELING) && defined(Z_ENDSTOP_SERVO_NR))
+ #define SERVO_LEVELING (defined(AUTO_BED_LEVELING_FEATURE) && defined(Z_ENDSTOP_SERVO_NR))
/**
* Sled Options
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 772683877d..bc972625b8 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -442,10 +442,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -557,7 +558,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -608,7 +609,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h
index 4c6ef0adb9..33487c869e 100644
--- a/Marlin/Marlin.h
+++ b/Marlin/Marlin.h
@@ -268,7 +268,7 @@ extern bool axis_known_position[3]; // axis[n].is_known
extern float delta_diagonal_rod;
extern float delta_segments_per_second;
void recalc_delta_settings(float radius, float diagonal_rod);
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
extern int delta_grid_spacing[2];
void adjust_delta(float cartesian[3]);
#endif
@@ -282,7 +282,7 @@ extern bool axis_known_position[3]; // axis[n].is_known
extern float z_endstop_adj;
#endif
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
extern float zprobe_zoffset;
#endif
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 88c5bfc8d4..ea4b2fd212 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -29,12 +29,12 @@
#include "Marlin.h"
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#include "vector_3.h"
#if ENABLED(AUTO_BED_LEVELING_GRID)
#include "qr_solve.h"
#endif
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
#if ENABLED(MESH_BED_LEVELING)
#include "mesh_bed_leveling.h"
@@ -288,7 +288,7 @@ static uint8_t target_extruder;
bool no_wait_for_cooling = true;
bool target_direction;
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
int xy_travel_speed = XY_TRAVEL_SPEED;
float zprobe_zoffset = Z_PROBE_OFFSET_FROM_EXTRUDER;
#endif
@@ -366,7 +366,7 @@ bool target_direction;
float delta_diagonal_rod = DELTA_DIAGONAL_ROD;
float delta_diagonal_rod_2 = sq(delta_diagonal_rod);
float delta_segments_per_second = DELTA_SEGMENTS_PER_SECOND;
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
int delta_grid_spacing[2] = { 0, 0 };
float bed_level[AUTO_BED_LEVELING_GRID_POINTS][AUTO_BED_LEVELING_GRID_POINTS];
#endif
@@ -1095,7 +1095,7 @@ static void set_axis_is_at_home(AxisEnum axis) {
min_pos[axis] = base_min_pos(axis) + home_offset[axis];
max_pos[axis] = base_max_pos(axis) + home_offset[axis];
- #if ENABLED(ENABLE_AUTO_BED_LEVELING) && Z_HOME_DIR < 0
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE) && Z_HOME_DIR < 0
if (axis == Z_AXIS) current_position[Z_AXIS] -= zprobe_zoffset;
#endif
}
@@ -1146,7 +1146,7 @@ static void setup_for_endstop_move() {
enable_endstops(true);
}
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if ENABLED(DELTA)
/**
@@ -1604,7 +1604,7 @@ static void setup_for_endstop_move() {
#endif
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
#if ENABLED(Z_PROBE_SLED)
@@ -2000,7 +2000,7 @@ inline void gcode_G28() {
st_synchronize();
// For auto bed leveling, clear the level matrix
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
plan_bed_level_matrix.set_to_identity();
#if ENABLED(DELTA)
reset_bed_level();
@@ -2395,7 +2395,7 @@ inline void gcode_G28() {
} // switch(state)
}
-#elif ENABLED(ENABLE_AUTO_BED_LEVELING)
+#elif ENABLED(AUTO_BED_LEVELING_FEATURE)
void out_of_range_error(const char *p_edge) {
SERIAL_PROTOCOLPGM("?Probe ");
@@ -2839,7 +2839,7 @@ inline void gcode_G28() {
#endif //!Z_PROBE_SLED
-#endif //ENABLE_AUTO_BED_LEVELING
+#endif //AUTO_BED_LEVELING_FEATURE
/**
* G92: Set current position to given X Y Z E
@@ -3116,7 +3116,7 @@ inline void gcode_M42() {
} // code_seen('S')
}
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
// This is redundant since the SanityCheck.h already checks for a valid Z_MIN_PROBE_PIN, but here for clarity.
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
@@ -3366,7 +3366,7 @@ inline void gcode_M42() {
SERIAL_EOL; SERIAL_EOL;
}
-#endif // ENABLE_AUTO_BED_LEVELING && Z_MIN_PROBE_REPEATABILITY_TEST
+#endif // AUTO_BED_LEVELING_FEATURE && Z_MIN_PROBE_REPEATABILITY_TEST
/**
* M104: Set hot end temperature
@@ -4585,7 +4585,7 @@ inline void gcode_M303() {
*/
inline void gcode_M400() { st_synchronize(); }
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) && DISABLED(Z_PROBE_SLED) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY))
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) && DISABLED(Z_PROBE_SLED) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY))
/**
* M401: Engage Z Servo endstop if available
@@ -4607,7 +4607,7 @@ inline void gcode_M400() { st_synchronize(); }
stow_z_probe(false);
}
-#endif // ENABLE_AUTO_BED_LEVELING && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
+#endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
#if ENABLED(FILAMENT_SENSOR)
@@ -5282,13 +5282,13 @@ void process_next_command() {
gcode_G28();
break;
- #if ENABLED(ENABLE_AUTO_BED_LEVELING) || ENABLED(MESH_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
case 29: // G29 Detailed Z probe, probes the bed at 3 or more points.
gcode_G29();
break;
#endif
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if DISABLED(Z_PROBE_SLED)
@@ -5305,7 +5305,7 @@ void process_next_command() {
#endif // Z_PROBE_SLED
- #endif // ENABLE_AUTO_BED_LEVELING
+ #endif // AUTO_BED_LEVELING_FEATURE
case 90: // G90
relative_mode = false;
@@ -5377,11 +5377,11 @@ void process_next_command() {
gcode_M42();
break;
- #if ENABLED(ENABLE_AUTO_BED_LEVELING) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
case 48: // M48 Z probe repeatability
gcode_M48();
break;
- #endif // ENABLE_AUTO_BED_LEVELING && Z_MIN_PROBE_REPEATABILITY_TEST
+ #endif // AUTO_BED_LEVELING_FEATURE && Z_MIN_PROBE_REPEATABILITY_TEST
#if ENABLED(M100_FREE_MEMORY_WATCHER)
case 100:
@@ -5650,14 +5650,14 @@ void process_next_command() {
gcode_M400();
break;
- #if ENABLED(ENABLE_AUTO_BED_LEVELING) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY)) && DISABLED(Z_PROBE_SLED)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY)) && DISABLED(Z_PROBE_SLED)
case 401:
gcode_M401();
break;
case 402:
gcode_M402();
break;
- #endif // ENABLE_AUTO_BED_LEVELING && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
+ #endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
#if ENABLED(FILAMENT_SENSOR)
case 404: //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or display nominal filament width
@@ -5799,7 +5799,7 @@ void clamp_to_software_endstops(float target[3]) {
NOLESS(target[Y_AXIS], min_pos[Y_AXIS]);
float negative_z_offset = 0;
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
if (zprobe_zoffset < 0) negative_z_offset += zprobe_zoffset;
if (home_offset[Z_AXIS] < 0) negative_z_offset += home_offset[Z_AXIS];
#endif
@@ -5849,7 +5849,7 @@ void clamp_to_software_endstops(float target[3]) {
*/
}
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
// Adjust print surface height by linear interpolation over the bed_level array.
void adjust_delta(float cartesian[3]) {
@@ -5889,7 +5889,7 @@ void clamp_to_software_endstops(float target[3]) {
SERIAL_ECHOPGM(" offset="); SERIAL_ECHOLN(offset);
*/
}
- #endif // ENABLE_AUTO_BED_LEVELING
+ #endif // AUTO_BED_LEVELING_FEATURE
#endif // DELTA
@@ -6008,7 +6008,7 @@ void mesh_plan_buffer_line(float x, float y, float z, const float e, float feed_
calculate_delta(target);
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
adjust_delta(target);
#endif
@@ -6236,7 +6236,7 @@ void plan_arc(
#if ENABLED(DELTA) || ENABLED(SCARA)
calculate_delta(arc_target);
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
adjust_delta(arc_target);
#endif
plan_buffer_line(delta[X_AXIS], delta[Y_AXIS], delta[Z_AXIS], arc_target[E_AXIS], feed_rate, active_extruder);
@@ -6248,7 +6248,7 @@ void plan_arc(
// Ensure last segment arrives at target location.
#if ENABLED(DELTA) || ENABLED(SCARA)
calculate_delta(target);
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
adjust_delta(target);
#endif
plan_buffer_line(delta[X_AXIS], delta[Y_AXIS], delta[Z_AXIS], target[E_AXIS], feed_rate, active_extruder);
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index bf8dc1752f..8c9f8341fb 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -116,8 +116,8 @@
#if ENABLED(DELTA)
#error MESH_BED_LEVELING does not yet support DELTA printers.
#endif
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
- #error Select ENABLE_AUTO_BED_LEVELING or MESH_BED_LEVELING, not both.
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
+ #error Select AUTO_BED_LEVELING_FEATURE or MESH_BED_LEVELING, not both.
#endif
#if MESH_NUM_X_POINTS > 7 || MESH_NUM_Y_POINTS > 7
#error MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS need to be less than 8.
@@ -127,7 +127,7 @@
/**
* Auto Bed Leveling
*/
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
/**
* Require a Z min pin
@@ -137,7 +137,7 @@
#if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
#error You must have a Z min or Z probe endstop to enable Z_MIN_PROBE_REPEATABILITY_TEST.
#else
- #error ENABLE_AUTO_BED_LEVELING requires a Z min or Z probe endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin.
+ #error AUTO_BED_LEVELING_FEATURE requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin.
#endif
#endif
#endif
@@ -207,7 +207,7 @@
#endif // !AUTO_BED_LEVELING_GRID
- #endif // ENABLE_AUTO_BED_LEVELING
+ #endif // AUTO_BED_LEVELING_FEATURE
/**
* ULTIPANEL encoder
@@ -221,7 +221,7 @@
*/
#if ENABLED(DELTA)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if DISABLED(AUTO_BED_LEVELING_GRID)
#error Only AUTO_BED_LEVELING_GRID is supported with DELTA.
@@ -362,6 +362,8 @@
#error CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration.
#elif defined(HAS_AUTOMATIC_VERSIONING)
#error HAS_AUTOMATIC_VERSIONING deprecated - use USE_AUTOMATIC_VERSIONING instead
+ #elif defined(ENABLE_AUTO_BED_LEVELING)
+ #error ENABLE_AUTO_BED_LEVELING deprecated - use AUTO_BED_LEVELING_FEATURE instead
#endif
#endif //SANITYCHECK_H
diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp
index b1f757e0a3..edb2d97a2d 100644
--- a/Marlin/configuration_store.cpp
+++ b/Marlin/configuration_store.cpp
@@ -171,7 +171,7 @@ void Config_StoreSettings() {
for (uint8_t q=0; q<mesh_num_x*mesh_num_y; q++) EEPROM_WRITE_VAR(i, dummy);
#endif // MESH_BED_LEVELING
- #if DISABLED(ENABLE_AUTO_BED_LEVELING)
+ #if DISABLED(AUTO_BED_LEVELING_FEATURE)
float zprobe_zoffset = 0;
#endif
EEPROM_WRITE_VAR(i, zprobe_zoffset);
@@ -339,7 +339,7 @@ void Config_RetrieveSettings() {
for (int q = 0; q < mesh_num_x * mesh_num_y; q++) EEPROM_READ_VAR(i, dummy);
#endif // MESH_BED_LEVELING
- #if DISABLED(ENABLE_AUTO_BED_LEVELING)
+ #if DISABLED(AUTO_BED_LEVELING_FEATURE)
float zprobe_zoffset = 0;
#endif
EEPROM_READ_VAR(i, zprobe_zoffset);
@@ -498,7 +498,7 @@ void Config_ResetDefault() {
mbl.active = 0;
#endif
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
zprobe_zoffset = Z_PROBE_OFFSET_FROM_EXTRUDER;
#endif
@@ -857,7 +857,7 @@ void Config_PrintSettings(bool forReplay) {
/**
* Auto Bed Leveling
*/
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if ENABLED(CUSTOM_M_CODES)
if (!forReplay) {
CONFIG_ECHO_START;
diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h
index b6875b4247..4ba6dd2eae 100644
--- a/Marlin/configurator/config/Configuration.h
+++ b/Marlin/configurator/config/Configuration.h
@@ -442,10 +442,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -557,7 +558,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -608,7 +609,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 07b1463814..4f9ce10ce0 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -424,10 +424,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -539,7 +540,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -591,7 +592,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h
index 3067bdd4a9..d9586d7b2f 100644
--- a/Marlin/example_configurations/Felix/Configuration_DUAL.h
+++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h
@@ -394,10 +394,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -509,7 +511,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// The position of the homing switches
@@ -561,7 +563,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 2632dea4bd..3811129b71 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -434,10 +434,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -549,7 +551,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -600,7 +602,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index ddd5c7c587..5eec325e48 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -430,10 +430,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -545,7 +546,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -596,7 +597,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 841815efd8..79d001a451 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -442,10 +442,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -557,7 +559,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -608,7 +610,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index fb8de6a871..105b0521ef 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -428,10 +428,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -543,7 +544,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -595,7 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index e5f53e5c4b..e7b9f182d6 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -450,10 +450,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -565,7 +566,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -616,7 +617,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
//#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index 1c29d07427..1728d19b65 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -434,10 +434,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -549,7 +550,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -600,7 +601,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index eea33d356f..031cceb4f1 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -442,10 +442,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -557,7 +559,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -608,7 +610,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index c0acd19a64..68c8d97e40 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -477,10 +477,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // Z probe repeatability test is not supported in Deltas yet.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -677,7 +678,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -728,7 +729,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 0c5e47f48b..2a54d8b251 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -477,10 +477,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // Z probe repeatability test is not supported in Deltas yet.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations.
//
@@ -677,7 +679,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -728,7 +730,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 4b939c6df8..e733555c09 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -477,10 +477,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // Z probe repeatability test is not supported in Deltas yet.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -681,7 +683,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -732,7 +734,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 1319e785f8..cfe6c0e9ea 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -464,10 +464,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -666,7 +668,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -727,7 +729,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -15
#define Z_PROBE_OFFSET_RANGE_MAX -5
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 1f7b6d1dc5..b5fb7567ed 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -445,10 +445,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -560,7 +561,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -611,7 +612,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index b6b79df924..4e349dec40 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -432,10 +432,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section bedlevel
-//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
-#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@@ -547,7 +549,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//
//#define Z_MIN_PROBE_ENDSTOP
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@@ -602,7 +604,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
diff --git a/Marlin/planner.cpp b/Marlin/planner.cpp
index e169865b22..e18b64e596 100644
--- a/Marlin/planner.cpp
+++ b/Marlin/planner.cpp
@@ -77,14 +77,14 @@ float max_e_jerk;
float mintravelfeedrate;
unsigned long axis_steps_per_sqr_second[NUM_AXIS];
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// Transform required to compensate for bed level
matrix_3x3 plan_bed_level_matrix = {
1.0, 0.0, 0.0,
0.0, 1.0, 0.0,
0.0, 0.0, 1.0
};
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
#if ENABLED(AUTOTEMP)
float autotemp_max = 250;
@@ -474,11 +474,11 @@ float junction_deviation = 0.1;
// Add a new linear movement to the buffer. steps[X_AXIS], _y and _z is the absolute position in
// mm. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
// calculation the caller must also provide the physical length of the line in millimeters.
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) || ENABLED(MESH_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, const uint8_t extruder)
#else
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t extruder)
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
{
// Calculate the buffer head after we push this byte
int next_buffer_head = next_block_index(block_buffer_head);
@@ -489,7 +489,7 @@ float junction_deviation = 0.1;
#if ENABLED(MESH_BED_LEVELING)
if (mbl.active) z += mbl.get_z(x, y);
- #elif ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #elif ENABLED(AUTO_BED_LEVELING_FEATURE)
apply_rotation_xyz(plan_bed_level_matrix, x, y, z);
#endif
@@ -993,7 +993,7 @@ float junction_deviation = 0.1;
} // plan_buffer_line()
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) && DISABLED(DELTA)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) && DISABLED(DELTA)
vector_3 plan_get_position() {
vector_3 position = vector_3(st_get_position_mm(X_AXIS), st_get_position_mm(Y_AXIS), st_get_position_mm(Z_AXIS));
@@ -1006,17 +1006,17 @@ float junction_deviation = 0.1;
return position;
}
-#endif // ENABLE_AUTO_BED_LEVELING && !DELTA
+#endif // AUTO_BED_LEVELING_FEATURE && !DELTA
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) || ENABLED(MESH_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
void plan_set_position(float x, float y, float z, const float &e)
#else
void plan_set_position(const float &x, const float &y, const float &z, const float &e)
-#endif // ENABLE_AUTO_BED_LEVELING || MESH_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
{
#if ENABLED(MESH_BED_LEVELING)
if (mbl.active) z += mbl.get_z(x, y);
- #elif ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #elif ENABLED(AUTO_BED_LEVELING_FEATURE)
apply_rotation_xyz(plan_bed_level_matrix, x, y, z);
#endif
diff --git a/Marlin/planner.h b/Marlin/planner.h
index fbe0336ad4..c186563eb3 100644
--- a/Marlin/planner.h
+++ b/Marlin/planner.h
@@ -79,9 +79,9 @@ extern volatile unsigned char block_buffer_head;
extern volatile unsigned char block_buffer_tail;
FORCE_INLINE uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block_buffer_tail + BLOCK_BUFFER_SIZE); }
-#if ENABLED(ENABLE_AUTO_BED_LEVELING) || ENABLED(MESH_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
#include "vector_3.h"
// Transform required to compensate for bed level
@@ -91,7 +91,7 @@ FORCE_INLINE uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block
* Get the position applying the bed level matrix
*/
vector_3 plan_get_position();
- #endif // ENABLE_AUTO_BED_LEVELING
+ #endif // AUTO_BED_LEVELING_FEATURE
/**
* Add a new linear movement to the buffer. x, y, z are the signed, absolute target position in
@@ -111,7 +111,7 @@ FORCE_INLINE uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t extruder);
void plan_set_position(const float &x, const float &y, const float &z, const float &e);
-#endif // ENABLE_AUTO_BED_LEVELING || MESH_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
void plan_set_e_position(const float &e);
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index 12910085a4..6f0d7e1088 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -638,7 +638,7 @@ static void lcd_prepare_menu() {
//
// Level Bed
//
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
if (axis_known_position[X_AXIS] && axis_known_position[Y_AXIS])
MENU_ITEM(gcode, MSG_LEVEL_BED, PSTR("G29"));
#elif ENABLED(MANUAL_BED_LEVELING)
@@ -1041,7 +1041,7 @@ static void lcd_control_temperature_preheat_abs_settings_menu() {
static void lcd_control_motion_menu() {
START_MENU();
MENU_ITEM(back, MSG_CONTROL, lcd_control_menu);
- #if ENABLED(ENABLE_AUTO_BED_LEVELING)
+ #if ENABLED(AUTO_BED_LEVELING_FEATURE)
MENU_ITEM_EDIT(float32, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
#endif
MENU_ITEM_EDIT(float5, MSG_ACC, &acceleration, 10, 99000);
diff --git a/Marlin/vector_3.cpp b/Marlin/vector_3.cpp
index 525480be33..e6b2d70c35 100644
--- a/Marlin/vector_3.cpp
+++ b/Marlin/vector_3.cpp
@@ -19,7 +19,7 @@
#include <math.h>
#include "Marlin.h"
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#include "vector_3.h"
vector_3::vector_3() : x(0), y(0), z(0) { }
@@ -134,5 +134,5 @@ void matrix_3x3::debug(const char title[]) {
}
}
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
diff --git a/Marlin/vector_3.h b/Marlin/vector_3.h
index 1c91e8b347..5aba350007 100644
--- a/Marlin/vector_3.h
+++ b/Marlin/vector_3.h
@@ -19,7 +19,7 @@
#ifndef VECTOR_3_H
#define VECTOR_3_H
-#if ENABLED(ENABLE_AUTO_BED_LEVELING)
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
class matrix_3x3;
struct vector_3
@@ -57,6 +57,6 @@ struct matrix_3x3
void apply_rotation_xyz(matrix_3x3 rotationMatrix, float &x, float& y, float& z);
-#endif // ENABLE_AUTO_BED_LEVELING
+#endif // AUTO_BED_LEVELING_FEATURE
#endif // VECTOR_3_H