diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index ece65bd6c4..3e508424f7 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -28,6 +28,7 @@
// 3 = MEGA/RAMPS up to 1.2 = 3
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
+// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 943e9e1e15..4dfe4ba624 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -146,6 +146,31 @@
#define EXTRUDERS 1
#endif
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds.
+//#define DUAL_X_CARRIAGE
+#ifdef DUAL_X_CARRIAGE
+// Configuration for second X-carriage
+// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+// the second x-carriage always homes to the maximum endstop.
+#define X2_MIN_POS 88 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+#define X2_MAX_POS 350.45 // set maximum to the distance between toolheads when both heads are homed
+#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
+#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+ // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
+ // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+ // without modifying the firmware (through the "M218 T1 X???" command).
+ // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
+#define X2_ENABLE_PIN 29
+#define X2_STEP_PIN 25
+#define X2_DIR_PIN 23
+
+#endif // DUAL_X_CARRIAGE
+
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
#define X_HOME_RETRACT_MM 5
#define Y_HOME_RETRACT_MM 5
diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h
index c9759eb219..1ae9494e34 100644
--- a/Marlin/Marlin.h
+++ b/Marlin/Marlin.h
@@ -96,7 +96,11 @@ void process_commands();
void manage_inactivity();
-#if defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1
+#if defined(DUAL_X_CARRIAGE) && defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1 \
+ && defined(X2_ENABLE_PIN) && X2_ENABLE_PIN > -1
+ #define enable_x() do { WRITE(X_ENABLE_PIN, X_ENABLE_ON); WRITE(X2_ENABLE_PIN, X_ENABLE_ON); } while (0)
+ #define disable_x() do { WRITE(X_ENABLE_PIN,!X_ENABLE_ON); WRITE(X2_ENABLE_PIN,!X_ENABLE_ON); } while (0)
+#elif defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index fc0c952240..886edca490 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -194,6 +194,10 @@ int EtoPPressure=0;
float retract_recover_length=0, retract_recover_feedrate=8*60;
#endif
+#ifdef ULTIPANEL
+ bool powersupply = true;
+#endif
+
//===========================================================================
//=============================private variables=============================
//===========================================================================
@@ -677,7 +681,44 @@ XYZ_CONSTS_FROM_CONFIG(float, max_length, MAX_LENGTH);
XYZ_CONSTS_FROM_CONFIG(float, home_retract_mm, HOME_RETRACT_MM);
XYZ_CONSTS_FROM_CONFIG(signed char, home_dir, HOME_DIR);
+#ifdef DUAL_X_CARRIAGE
+ #if EXTRUDERS == 1 || defined(COREXY) \
+ || !defined(X2_ENABLE_PIN) || !defined(X2_STEP_PIN) || !defined(X2_DIR_PIN) \
+ || !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS) \
+ || !defined(X_MAX_PIN) || X_MAX_PIN < 0
+ #error "Missing or invalid definitions for DUAL_X_CARRIAGE mode."
+ #endif
+ #if X_HOME_DIR != -1 || X2_HOME_DIR != 1
+ #error "Please use canonical x-carriage assignment" // the x-carriages are defined by their homing directions
+ #endif
+
+static float x_home_pos(int extruder) {
+ if (extruder == 0)
+ return base_home_pos(X_AXIS) + add_homeing[X_AXIS];
+ else
+ // In dual carriage mode the extruder offset provides an override of the
+ // second X-carriage offset when homed - otherwise X2_HOME_POS is used.
+ // This allow soft recalibration of the second extruder offset position without firmware reflash
+ // (through the M218 command).
+ return (extruder_offset[X_AXIS][1] > 0) ? extruder_offset[X_AXIS][1] : X2_HOME_POS;
+}
+
+static int x_home_dir(int extruder) {
+ return (extruder == 0) ? X_HOME_DIR : X2_HOME_DIR;
+}
+
+static float inactive_x_carriage_pos = X2_MAX_POS;
+#endif
+
static void axis_is_at_home(int axis) {
+#ifdef DUAL_X_CARRIAGE
+ if (axis == X_AXIS && active_extruder != 0) {
+ current_position[X_AXIS] = x_home_pos(active_extruder);
+ min_pos[X_AXIS] = X2_MIN_POS;
+ max_pos[X_AXIS] = max(extruder_offset[X_AXIS][1], X2_MAX_POS);
+ return;
+ }
+#endif
current_position[axis] = base_home_pos(axis) + add_homeing[axis];
min_pos[axis] = base_min_pos(axis) + add_homeing[axis];
max_pos[axis] = base_max_pos(axis) + add_homeing[axis];
@@ -686,10 +727,16 @@ static void axis_is_at_home(int axis) {
static void homeaxis(int axis) {
#define HOMEAXIS_DO(LETTER) \
((LETTER##_MIN_PIN > -1 && LETTER##_HOME_DIR==-1) || (LETTER##_MAX_PIN > -1 && LETTER##_HOME_DIR==1))
+
if (axis==X_AXIS ? HOMEAXIS_DO(X) :
axis==Y_AXIS ? HOMEAXIS_DO(Y) :
axis==Z_AXIS ? HOMEAXIS_DO(Z) :
0) {
+ int axis_home_dir = home_dir(axis);
+#ifdef DUAL_X_CARRIAGE
+ if (axis == X_AXIS)
+ axis_home_dir = x_home_dir(active_extruder);
+#endif
// Engage Servo endstop if enabled
#ifdef SERVO_ENDSTOPS
@@ -700,18 +747,18 @@ static void homeaxis(int axis) {
current_position[axis] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
- destination[axis] = 1.5 * max_length(axis) * home_dir(axis);
+ destination[axis] = 1.5 * max_length(axis) * axis_home_dir;
feedrate = homing_feedrate[axis];
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
st_synchronize();
current_position[axis] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
- destination[axis] = -home_retract_mm(axis) * home_dir(axis);
+ destination[axis] = -home_retract_mm(axis) * axis_home_dir;
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
st_synchronize();
- destination[axis] = 2*home_retract_mm(axis) * home_dir(axis);
+ destination[axis] = 2*home_retract_mm(axis) * axis_home_dir;
#ifdef DELTA
feedrate = homing_feedrate[axis]/10;
#else
@@ -855,7 +902,7 @@ void process_commands()
#else // NOT DELTA
- home_all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2])));
+ home_all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2])));
#if Z_HOME_DIR > 0 // If homing away from BED do Z first
if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) {
@@ -868,8 +915,14 @@ void process_commands()
{
current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0;
+ #ifndef DUAL_X_CARRIAGE
+ int x_axis_home_dir = home_dir(X_AXIS);
+ #else
+ int x_axis_home_dir = x_home_dir(active_extruder);
+ #endif
+
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
- destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR;
+ destination[X_AXIS] = 1.5 * max_length(X_AXIS) * x_axis_home_dir;destination[Y_AXIS] = 1.5 * max_length(Y_AXIS) * home_dir(Y_AXIS);
feedrate = homing_feedrate[X_AXIS];
if(homing_feedrate[Y_AXIS]<feedrate)
feedrate =homing_feedrate[Y_AXIS];
@@ -894,6 +947,13 @@ void process_commands()
if((home_all_axis) || (code_seen(axis_codes[X_AXIS])))
{
+ #ifdef DUAL_X_CARRIAGE
+ int tmp_extruder = active_extruder;
+ active_extruder = !active_extruder;
+ HOMEAXIS(X);
+ inactive_x_carriage_pos = current_position[X_AXIS];
+ active_extruder = tmp_extruder;
+ #endif
HOMEAXIS(X);
}
@@ -926,7 +986,7 @@ void process_commands()
}
}
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
-#endif // DELTA
+#endif // else DELTA
#ifdef ENDSTOPS_ONLY_FOR_HOMING
enable_endstops(false);
@@ -1338,14 +1398,26 @@ void process_commands()
#endif
#if defined(PS_ON_PIN) && PS_ON_PIN > -1
- case 80: // M80 - ATX Power On
+ case 80: // M80 - Turn on Power Supply
SET_OUTPUT(PS_ON_PIN); //GND
WRITE(PS_ON_PIN, PS_ON_AWAKE);
+ #ifdef ULTIPANEL
+ powersupply = true;
+ LCD_MESSAGEPGM(WELCOME_MSG);
+ lcd_update();
+ #endif
break;
#endif
-
- case 81: // M81 - ATX Power Off
-
+
+ case 81: // M81 - Turn off Power Supply
+ disable_heater();
+ st_synchronize();
+ disable_e0();
+ disable_e1();
+ disable_e2();
+ finishAndDisableSteppers();
+ fanSpeed = 0;
+ delay(1000); // Wait a little before to switch off
#if defined(SUICIDE_PIN) && SUICIDE_PIN > -1
st_synchronize();
suicide();
@@ -1353,7 +1425,12 @@ void process_commands()
SET_OUTPUT(PS_ON_PIN);
WRITE(PS_ON_PIN, PS_ON_ASLEEP);
#endif
- break;
+ #ifdef ULTIPANEL
+ powersupply = false;
+ LCD_MESSAGEPGM(MACHINE_NAME" "MSG_OFF".");
+ lcd_update();
+ #endif
+ break;
case 82:
axis_relative_modes[3] = false;
@@ -2005,6 +2082,20 @@ void process_commands()
if(tmp_extruder != active_extruder) {
// Save current position to return to after applying extruder offset
memcpy(destination, current_position, sizeof(destination));
+ #ifdef DUAL_X_CARRIAGE
+ // only apply Y extruder offset in dual x carriage mode (x offset is already used in determining home pos)
+ current_position[Y_AXIS] = current_position[Y_AXIS] -
+ extruder_offset[Y_AXIS][active_extruder] +
+ extruder_offset[Y_AXIS][tmp_extruder];
+
+ float tmp_x_pos = current_position[X_AXIS];
+
+ // Set the new active extruder and position
+ active_extruder = tmp_extruder;
+ axis_is_at_home(X_AXIS); //this function updates X min/max values.
+ current_position[X_AXIS] = inactive_x_carriage_pos;
+ inactive_x_carriage_pos = tmp_x_pos;
+ #else
// Offset extruder (only by XY)
int i;
for(i = 0; i < 2; i++) {
@@ -2014,6 +2105,7 @@ void process_commands()
}
// Set the new active extruder and position
active_extruder = tmp_extruder;
+ #endif //else DUAL_X_CARRIAGE
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
// Move to the old position if 'F' was in the parameters
if(make_move && Stopped == false) {
@@ -2258,6 +2350,9 @@ void controllerFan()
|| !READ(E2_ENABLE_PIN)
#endif
#if EXTRUDER > 1
+ #if defined(X2_ENABLE_PIN) && X2_ENABLE_PIN > -1
+ || !READ(X2_ENABLE_PIN)
+ #endif
|| !READ(E1_ENABLE_PIN)
#endif
|| !READ(E0_ENABLE_PIN)) //If any of the drivers are enabled...
diff --git a/Marlin/language.h b/Marlin/language.h
index d8802cdd83..17222c7cd2 100644
--- a/Marlin/language.h
+++ b/Marlin/language.h
@@ -1,1506 +1,1537 @@
-#ifndef LANGUAGE_H
-#define LANGUAGE_H
-
-// NOTE: IF YOU CHANGE THIS FILE / MERGE THIS FILE WITH CHANGES
-//
-// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h"
-// ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS
-
-// Languages
-// 1 English
-// 2 Polish
-// 3 French
-// 4 German
-// 5 Spanish
-// 6 Russian
-// 7 Italian
-// 8 Portuguese
-// 9 Finnish
-
-#ifndef LANGUAGE_CHOICE
-#define LANGUAGE_CHOICE 1 // Pick your language from the list above
-#endif
-
-#define PROTOCOL_VERSION "1.0"
-
-#if MOTHERBOARD == 7 || MOTHERBOARD == 71
- #define MACHINE_NAME "Ultimaker"
- #define FIRMWARE_URL "http://firmware.ultimaker.com"
-#elif MOTHERBOARD == 80
- #define MACHINE_NAME "Rumba"
- #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/"
-#elif MOTHERBOARD == 77
- #define MACHINE_NAME "3Drag"
- #define FIRMWARE_URL "http://3dprint.elettronicain.it/"
-#else
- #ifdef CUSTOM_MENDEL_NAME
- #define MACHINE_NAME CUSTOM_MENDEL_NAME
- #else
- #define MACHINE_NAME "Mendel"
- #endif
- #define FIRMWARE_URL "http://www.mendel-parts.com"
-#endif
-
-#define STRINGIFY_(n) #n
-#define STRINGIFY(n) STRINGIFY_(n)
-
-#if LANGUAGE_CHOICE == 1
-
-// LCD Menu Messages
- #define WELCOME_MSG MACHINE_NAME " Ready."
- #define MSG_SD_INSERTED "Card inserted"
- #define MSG_SD_REMOVED "Card removed"
- #define MSG_MAIN "Main"
- #define MSG_AUTOSTART "Autostart"
- #define MSG_DISABLE_STEPPERS "Disable Steppers"
- #define MSG_AUTO_HOME "Auto Home"
- #define MSG_SET_ORIGIN "Set Origin"
- #define MSG_PREHEAT_PLA "Preheat PLA"
- #define MSG_PREHEAT_PLA_SETTINGS "Preheat PLA Conf"
- #define MSG_PREHEAT_ABS "Preheat ABS"
- #define MSG_PREHEAT_ABS_SETTINGS "Preheat ABS Conf"
- #define MSG_COOLDOWN "Cooldown"
- #define MSG_EXTRUDE "Extrude"
- #define MSG_RETRACT "Retract"
- #define MSG_MOVE_AXIS "Move Axis"
- #define MSG_SPEED "Speed"
- #define MSG_NOZZLE "Nozzle"
- #define MSG_NOZZLE1 "Nozzle2"
- #define MSG_NOZZLE2 "Nozzle3"
- #define MSG_BED "Bed"
- #define MSG_FAN_SPEED "Fan speed"
- #define MSG_FLOW "Flow"
- #define MSG_CONTROL "Control"
- #define MSG_MIN " \002 Min"
- #define MSG_MAX " \002 Max"
- #define MSG_FACTOR " \002 Fact"
- #define MSG_AUTOTEMP "Autotemp"
- #define MSG_ON "On "
- #define MSG_OFF "Off"
- #define MSG_PID_P "PID-P"
- #define MSG_PID_I "PID-I"
- #define MSG_PID_D "PID-D"
- #define MSG_PID_C "PID-C"
- #define MSG_ACC "Accel"
- #define MSG_VXY_JERK "Vxy-jerk"
- #define MSG_VZ_JERK "Vz-jerk"
- #define MSG_VE_JERK "Ve-jerk"
- #define MSG_VMAX "Vmax "
- #define MSG_X "x"
- #define MSG_Y "y"
- #define MSG_Z "z"
- #define MSG_E "e"
- #define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "VTrav min"
- #define MSG_AMAX "Amax "
- #define MSG_A_RETRACT "A-retract"
- #define MSG_XSTEPS "Xsteps/mm"
- #define MSG_YSTEPS "Ysteps/mm"
- #define MSG_ZSTEPS "Zsteps/mm"
- #define MSG_ESTEPS "Esteps/mm"
- #define MSG_RECTRACT "Rectract"
- #define MSG_TEMPERATURE "Temperature"
- #define MSG_MOTION "Motion"
- #define MSG_CONTRAST "LCD contrast"
- #define MSG_STORE_EPROM "Store memory"
- #define MSG_LOAD_EPROM "Load memory"
- #define MSG_RESTORE_FAILSAFE "Restore Failsafe"
- #define MSG_REFRESH "Refresh"
- #define MSG_WATCH "Info screen"
- #define MSG_PREPARE "Prepare"
- #define MSG_TUNE "Tune"
- #define MSG_PAUSE_PRINT "Pause Print"
- #define MSG_RESUME_PRINT "Resume Print"
- #define MSG_STOP_PRINT "Stop Print"
- #define MSG_CARD_MENU "Print from SD"
- #define MSG_NO_CARD "No Card"
- #define MSG_DWELL "Sleep..."
- #define MSG_USERWAIT "Wait for user..."
- #define MSG_RESUMING "Resuming print"
- #define MSG_NO_MOVE "No move."
- #define MSG_KILLED "KILLED. "
- #define MSG_STOPPED "STOPPED. "
- #define MSG_CONTROL_RETRACT "Retract mm"
- #define MSG_CONTROL_RETRACTF "Retract F"
- #define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
- #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
- #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
- #define MSG_AUTORETRACT "AutoRetr."
- #define MSG_FILAMENTCHANGE "Change filament"
- #define MSG_INIT_SDCARD "Init. SD-Card"
- #define MSG_CNG_SDCARD "Change SD-Card"
-
-// Serial Console Messages
-
- #define MSG_Enqueing "enqueing \""
- #define MSG_POWERUP "PowerUp"
- #define MSG_EXTERNAL_RESET " External Reset"
- #define MSG_BROWNOUT_RESET " Brown out Reset"
- #define MSG_WATCHDOG_RESET " Watchdog Reset"
- #define MSG_SOFTWARE_RESET " Software Reset"
- #define MSG_MARLIN "Marlin "
- #define MSG_AUTHOR " | Author: "
- #define MSG_CONFIGURATION_VER " Last Updated: "
- #define MSG_FREE_MEMORY " Free Memory: "
- #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "Done saving file."
- #define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line: "
- #define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line: "
- #define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line: "
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line: "
- #define MSG_FILE_PRINTED "Done printing file"
- #define MSG_BEGIN_FILE_LIST "Begin file list"
- #define MSG_END_FILE_LIST "End file list"
- #define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
- #define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
- #define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
- #define MSG_ERR_NO_THERMISTORS "No thermistors - no temperature"
- #define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
- #define MSG_HEATING "Heating..."
- #define MSG_HEATING_COMPLETE "Heating done."
- #define MSG_BED_HEATING "Bed Heating."
- #define MSG_BED_DONE "Bed done."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Count X: "
- #define MSG_ERR_KILLED "Printer halted. kill() called!"
- #define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
- #define MSG_RESEND "Resend: "
- #define MSG_UNKNOWN_COMMAND "Unknown command: \""
- #define MSG_ACTIVE_EXTRUDER "Active Extruder: "
- #define MSG_INVALID_EXTRUDER "Invalid extruder"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Reporting endstop status"
- #define MSG_ENDSTOP_HIT "TRIGGERED"
- #define MSG_ENDSTOP_OPEN "open"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
- #define MSG_SD_INIT_FAIL "SD init fail"
- #define MSG_SD_VOL_INIT_FAIL "volume.init failed"
- #define MSG_SD_OPENROOT_FAIL "openRoot failed"
- #define MSG_SD_CARD_OK "SD card ok"
- #define MSG_SD_WORKDIR_FAIL "workDir open failed"
- #define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
- #define MSG_SD_FILE_OPENED "File opened: "
- #define MSG_SD_SIZE " Size: "
- #define MSG_SD_FILE_SELECTED "File selected"
- #define MSG_SD_WRITE_TO_FILE "Writing to file: "
- #define MSG_SD_PRINTING_BYTE "SD printing byte "
- #define MSG_SD_NOT_PRINTING "Not SD printing"
- #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
- #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir: "
-
- #define MSG_STEPPER_TOO_HIGH "Steprate too high: "
- #define MSG_ENDSTOPS_HIT "endstops hit: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
- #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 2
-
-// LCD Menu Messages
- #define WELCOME_MSG MACHINE_NAME " Gotowe."
- #define MSG_SD_INSERTED "Karta wlozona"
- #define MSG_SD_REMOVED "Karta usunieta"
- #define MSG_MAIN "Main"
- #define MSG_AUTOSTART "Autostart"
- #define MSG_DISABLE_STEPPERS "Wylacz silniki"
- #define MSG_AUTO_HOME "Auto. poz. zerowa"
- #define MSG_SET_ORIGIN "Ustaw punkt zerowy"
- #define MSG_PREHEAT_PLA "Rozgrzej PLA"
- #define MSG_PREHEAT_PLA_SETTINGS "Ustawienia roz. PLA"
- #define MSG_PREHEAT_ABS "Rozgrzej ABS"
- #define MSG_PREHEAT_ABS_SETTINGS "Ustawienia roz. ABS"
- #define MSG_COOLDOWN "Chlodzenie"
- #define MSG_EXTRUDE "Ekstruzja"
- #define MSG_RETRACT "Cofanie"
- #define MSG_MOVE_AXIS "Ruch osi"
- #define MSG_SPEED "Predkosc"
- #define MSG_NOZZLE "Dysza"
- #define MSG_NOZZLE1 "Dysza2"
- #define MSG_NOZZLE2 "Dysza3"
- #define MSG_BED "Loze"
- #define MSG_FAN_SPEED "Obroty wiatraka"
- #define MSG_FLOW "Przeplyw"
- #define MSG_CONTROL "Kontrola"
- #define MSG_MIN " \002 Min"
- #define MSG_MAX " \002 Max"
- #define MSG_FACTOR " \002 Mnoznik"
- #define MSG_AUTOTEMP "Auto. temp."
- #define MSG_ON "Wl. "
- #define MSG_OFF "Wyl."
- #define MSG_PID_P "PID-P"
- #define MSG_PID_I "PID-I"
- #define MSG_PID_D "PID-D"
- #define MSG_PID_C "PID-C"
- #define MSG_ACC "Acc"
- #define MSG_VXY_JERK "Zryw Vxy"
- #define MSG_VZ_JERK "Zryw Vz"
- #define MSG_VE_JERK "Zryw Ve"
- #define MSG_VMAX "Vmax"
- #define MSG_X "x"
- #define MSG_Y "y"
- #define MSG_Z "z"
- #define MSG_E "e"
- #define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "Vskok min"
- #define MSG_AMAX "Amax"
- #define MSG_A_RETRACT "A-wycofanie"
- #define MSG_XSTEPS "krokiX/mm"
- #define MSG_YSTEPS "krokiY/mm"
- #define MSG_ZSTEPS "krokiZ/mm"
- #define MSG_ESTEPS "krokiE/mm"
- #define MSG_RECTRACT "Wycofanie"
- #define MSG_TEMPERATURE "Temperatura"
- #define MSG_MOTION "Ruch"
- #define MSG_CONTRAST "LCD contrast"
- #define MSG_STORE_EPROM "Zapisz w pamieci"
- #define MSG_LOAD_EPROM "Wczytaj z pamieci"
- #define MSG_RESTORE_FAILSAFE " Ustawienia fabryczne"
- #define MSG_REFRESH "\004Odswiez"
- #define MSG_WATCH "Obserwuj"
- #define MSG_PREPARE "Przygotuj"
- #define MSG_CONTROL "Kontroluj"
- #define MSG_TUNE "Strojenie"
- #define MSG_PAUSE_PRINT "Pauza"
- #define MSG_RESUME_PRINT "Wznowienie"
- #define MSG_STOP_PRINT "Stop"
- #define MSG_CARD_MENU "Menu SDCard"
- #define MSG_NO_CARD "Brak karty"
- #define MSG_DWELL "Uspij..."
- #define MSG_USERWAIT "Czekaj na uzytkownika..."
- #define MSG_RESUMING "Wznawiam drukowanie"
- #define MSG_NO_MOVE "Brak ruchu."
- #define MSG_PART_RELEASE "Czesciowe zwolnienie"
- #define MSG_KILLED "Ubity. "
- #define MSG_STOPPED "Zatrzymany. "
- #define MSG_STEPPER_RELEASED "Zwolniony."
- #define MSG_CONTROL_RETRACT "Wycofaj mm"
- #define MSG_CONTROL_RETRACTF "Wycofaj F"
- #define MSG_CONTROL_RETRACT_ZLIFT "Skok Z mm:"
- #define MSG_CONTROL_RETRACT_RECOVER "Cof. wycof. +mm"
- #define MSG_CONTROL_RETRACT_RECOVERF "Cof. wycof. F"
- #define MSG_AUTORETRACT "Auto. wycofanie"
- #define MSG_FILAMENTCHANGE "Change filament"
-
-// Serial Console Messages
-
- #define MSG_Enqueing "Kolejkowanie \""
- #define MSG_POWERUP "Zasilanie wlaczone"
- #define MSG_EXTERNAL_RESET " Reset (zewnetrzny)"
- #define MSG_BROWNOUT_RESET " Reset (spadek napiecia)"
- #define MSG_WATCHDOG_RESET " Reset (watchdog)"
- #define MSG_SOFTWARE_RESET " Reset (programowy)"
- #define MSG_MARLIN "Marlin "
- #define MSG_AUTHOR " | Autor: "
- #define MSG_CONFIGURATION_VER " Ostatnia aktualizacja: "
- #define MSG_FREE_MEMORY " Wolna pamiec: "
- #define MSG_PLANNER_BUFFER_BYTES " Bufor planisty krokow (w bajtach): "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "Plik zapisany."
- #define MSG_ERR_LINE_NO "Numer linijki nie jest ostatnim numerem linijki+1; ostatnia linijka:"
- #define MSG_ERR_CHECKSUM_MISMATCH "Niezgodna suma kontrolna; ostatnia linijka: "
- #define MSG_ERR_NO_CHECKSUM "Brak sumy kontrolnej w linijce; ostatnia linijka:"
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Brak numery linijki przy sumie kontrolnej; ostatnia linijka:"
- #define MSG_FILE_PRINTED "Ukonczono wydruk z pliku"
- #define MSG_BEGIN_FILE_LIST "Start listy plikow"
- #define MSG_END_FILE_LIST "Koniec listy plikow"
- #define MSG_M104_INVALID_EXTRUDER "M104 Niepoprawny ekstruder "
- #define MSG_M105_INVALID_EXTRUDER "M105 Niepoprawny ekstruder "
- #define MSG_M218_INVALID_EXTRUDER "M218 Niepoprawny ekstruder "
- #define MSG_ERR_NO_THERMISTORS "Brak termistorow - brak temperatury :("
- #define MSG_M109_INVALID_EXTRUDER "M109 Niepoprawny ekstruder "
- #define MSG_HEATING "Nagrzewanie ekstrudera..."
- #define MSG_HEATING_COMPLETE "Nagrzewanie ekstrudera zakonczone."
- #define MSG_BED_HEATING "Nagrzewanie loza..."
- #define MSG_BED_DONE "Nagrzewanie loza zakonczone."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Liczenie X: "
- #define MSG_ERR_KILLED "Drukarka zatrzymana. Wywolano kill()"
- #define MSG_ERR_STOPPED "Drukarka zatrzymana z powodu bledu. Usun problem i zrestartuj drukartke komenda M999. (temperatura zostala zresetowana; ustaw temperature po restarcie)"
- #define MSG_RESEND "Wyslij ponownie: "
- #define MSG_UNKNOWN_COMMAND "Nieznane polecenie: \""
- #define MSG_ACTIVE_EXTRUDER "Aktywny ekstruder: "
- #define MSG_INVALID_EXTRUDER "Niepoprawny ekstruder"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Zgloszenie statusu wylacznikow krancowych"
- #define MSG_ENDSTOP_HIT "WYZWOLONY"
- #define MSG_ENDSTOP_OPEN "otwarty"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Nie mozna otworzyc podkatalogu"
- #define MSG_SD_INIT_FAIL "Blad inicjalizacji karty SD"
- #define MSG_SD_VOL_INIT_FAIL "Blad inizjalizacji wolumenu"
- #define MSG_SD_OPENROOT_FAIL "Blad odczytywania katalogu glownego"
- #define MSG_SD_CARD_OK "Karta SD zainicjalizowana"
- #define MSG_SD_WORKDIR_FAIL "Blad odczytywania katalogu roboczego"
- #define MSG_SD_OPEN_FILE_FAIL "Nie mozna otworzyc pliku: "
- #define MSG_SD_FILE_OPENED "Otwarto plik:"
- #define MSG_SD_SIZE " Rozmiar:"
- #define MSG_SD_FILE_SELECTED "Wybrano plik"
- #define MSG_SD_WRITE_TO_FILE "Zapisywanie do pliku: "
- #define MSG_SD_PRINTING_BYTE "Drukowanie z karty SD, bajt "
- #define MSG_SD_NOT_PRINTING "Nie trwa drukowanie z karty SD"
- #define MSG_SD_ERR_WRITE_TO_FILE "blad podczas zapisu do pliku"
- #define MSG_SD_CANT_ENTER_SUBDIR "Nie mozna odczytac podkatalogu: "
-
- #define MSG_STEPPER_TOO_HIGH "Za duza czestotliwosc krokow: "
- #define MSG_ENDSTOPS_HIT "Wylacznik krancowy zostal wyzwolony na pozycji: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " uniemozliwiono zimna ekstruzje"
- #define MSG_ERR_LONG_EXTRUDE_STOP " uniemozliwiono zbyt dluga ekstruzje"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 3
-
-#define WELCOME_MSG MACHINE_NAME " Pret."
-#define MSG_SD_INSERTED "Carte inseree"
-#define MSG_SD_REMOVED "Carte retiree"
-#define MSG_MAIN " Principal \003"
-#define MSG_AUTOSTART " Demarrage auto."
-#define MSG_DISABLE_STEPPERS " Desactiver moteurs"
-#define MSG_AUTO_HOME " Home auto."
-#define MSG_SET_ORIGIN " Regler origine"
-#define MSG_PREHEAT_PLA " Prechauffage PLA"
-#define MSG_PREHEAT_PLA_SETTINGS " Regl. prechauffe PLA"
-#define MSG_PREHEAT_ABS " Prechauffage ABS"
-#define MSG_PREHEAT_ABS_SETTINGS " Regl. prechauffe ABS"
-#define MSG_COOLDOWN " Refroidissement"
-#define MSG_EXTRUDE " Extrusion"
-#define MSG_RETRACT " Retractation"
-#define MSG_PREHEAT_PLA " Prechauffage PLA"
-#define MSG_PREHEAT_ABS " Prechauffage ABS"
-#define MSG_MOVE_AXIS " Deplacer axe \x7E"
-#define MSG_SPEED " Vitesse:"
-#define MSG_NOZZLE " \002Buse:"
-#define MSG_NOZZLE1 " \002Buse2:"
-#define MSG_NOZZLE2 " \002Buse3:"
-#define MSG_BED " \002Lit:"
-#define MSG_FAN_SPEED " Vitesse ventilateur:"
-#define MSG_FLOW " Flux:"
-#define MSG_CONTROL " Controle \003"
-#define MSG_MIN " \002 Min:"
-#define MSG_MAX " \002 Max:"
-#define MSG_FACTOR " \002 Facteur:"
-#define MSG_AUTOTEMP " Temp. Auto.:"
-#define MSG_ON "Marche "
-#define MSG_OFF "Arret"
-#define MSG_PID_P " PID-P: "
-#define MSG_PID_I " PID-I: "
-#define MSG_PID_D " PID-D: "
-#define MSG_PID_C " PID-C: "
-#define MSG_ACC " Acc:"
-#define MSG_VXY_JERK "Vxy-jerk"
-#define MSG_VZ_JERK "Vz-jerk"
-#define MSG_VE_JERK "Ve-jerk"
-#define MSG_VMAX " Vmax "
-#define MSG_X "x:"
-#define MSG_Y "y:"
-#define MSG_Z "z:"
-#define MSG_E "e:"
-#define MSG_VMIN " Vmin:"
-#define MSG_VTRAV_MIN " Vdepl min:"
-#define MSG_AMAX " Amax "
-#define MSG_A_RETRACT " A-retract:"
-#define MSG_XSTEPS " Xpas/mm:"
-#define MSG_YSTEPS " Ypas/mm:"
-#define MSG_ZSTEPS " Zpas/mm:"
-#define MSG_ESTEPS " Epas/mm:"
-#define MSG_MAIN_WIDE " Principal \003"
-#define MSG_RECTRACT_WIDE " Rectractater \x7E"
-#define MSG_TEMPERATURE_WIDE " Temperature \x7E"
-#define MSG_TEMPERATURE_RTN " Temperature \003"
-#define MSG_MOTION_WIDE " Mouvement \x7E"
- #define MSG_CONTRAST "LCD contrast"
-#define MSG_STORE_EPROM " Sauvegarder memoire"
-#define MSG_LOAD_EPROM " Lire memoire"
-#define MSG_RESTORE_FAILSAFE " Restaurer memoire"
-#define MSG_REFRESH "\004Actualiser"
-#define MSG_WATCH " Surveiller \003"
-#define MSG_PREPARE " Preparer \x7E"
-#define MSG_PREPARE_ALT " Prepare \003"
-#define MSG_CONTROL_ARROW " Controle \x7E"
-#define MSG_RETRACT_ARROW " Retracter \x7E"
-#define MSG_TUNE " Regler \x7E"
-#define MSG_PAUSE_PRINT " Pause impression \x7E"
-#define MSG_RESUME_PRINT " Reprendre impression \x7E"
-#define MSG_STOP_PRINT " Arreter impression \x7E"
-#define MSG_CARD_MENU " Menu carte \x7E"
-#define MSG_NO_CARD " Pas de carte"
-#define MSG_DWELL "Repos..."
-#define MSG_USERWAIT "Attente de l'utilisateur..."
-#define MSG_NO_MOVE "Aucun mouvement."
-#define MSG_PART_RELEASE "Relache partielle"
-#define MSG_KILLED "TUE."
-#define MSG_STOPPED "STOPPE."
-#define MSG_STEPPER_RELEASED "RELACHE."
-#define MSG_CONTROL_RETRACT " Retractation mm:"
-#define MSG_CONTROL_RETRACTF " Retractation F:"
-#define MSG_CONTROL_RETRACT_ZLIFT " Hop mm:"
-#define MSG_CONTROL_RETRACT_RECOVER " UnRet +mm:"
-#define MSG_CONTROL_RETRACT_RECOVERF " UnRet F:"
-#define MSG_AUTORETRACT " Retract. Auto.:"
-#define MSG_FILAMENTCHANGE "Change filament"
-
-// Serial Console Messages
-
-#define MSG_Enqueing "Mise en tampon \""
-#define MSG_POWERUP "Allumage"
-#define MSG_EXTERNAL_RESET " RAZ Externe"
-#define MSG_BROWNOUT_RESET " RAZ defaut alim."
-#define MSG_WATCHDOG_RESET " RAZ Watchdog"
-#define MSG_SOFTWARE_RESET " RAZ logicielle"
-#define MSG_MARLIN "Marlin "
-#define MSG_AUTHOR " | Auteur: "
-#define MSG_CONFIGURATION_VER " Derniere MaJ: "
-#define MSG_FREE_MEMORY " Memoire libre: "
-#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
-#define MSG_OK "ok"
-#define MSG_FILE_SAVED "Fichier enregistre."
-#define MSG_ERR_LINE_NO "Le numero de ligne n'est pas la derniere ligne + 1, derniere ligne: "
-#define MSG_ERR_CHECKSUM_MISMATCH "Erreur somme de controle, derniere ligne: "
-#define MSG_ERR_NO_CHECKSUM "Pas de somme de controle avec le numero de ligne, derniere ligne: "
-#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Pas de numero de ligne avec somme de controle, derniere ligne: "
-#define MSG_FILE_PRINTED "Impression terminee"
-#define MSG_BEGIN_FILE_LIST "Debut de la liste de fichiers"
-#define MSG_END_FILE_LIST "Fin de la liste de fichiers"
-#define MSG_M104_INVALID_EXTRUDER "M104 Extruder invalide"
-#define MSG_M105_INVALID_EXTRUDER "M105 Extruder invalide"
-#define MSG_M218_INVALID_EXTRUDER "M218 Extruder invalide"
-#define MSG_ERR_NO_THERMISTORS "Pas de thermistor, pas de temperature"
-#define MSG_M109_INVALID_EXTRUDER "M109 Extruder invalide "
-#define MSG_HEATING "En chauffe..."
-#define MSG_HEATING_COMPLETE "Chauffe terminee."
-#define MSG_BED_HEATING "Chauffe du lit."
-#define MSG_BED_DONE "Chauffe du lit terminee."
-#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
-#define MSG_COUNT_X " Compteur X: "
-#define MSG_ERR_KILLED "Impression arretee. kill() appelee!"
-#define MSG_ERR_STOPPED "Impression arretee a cause d'erreurs. Corriger les erreurs et utiliser M999 pour la reprendre. (Temperature remise a zero. Reactivez la apres redemarrage)"
-#define MSG_RESEND "Renvoie: "
-#define MSG_UNKNOWN_COMMAND "Commande inconnue: \""
-#define MSG_ACTIVE_EXTRUDER "Extrudeur actif: "
-#define MSG_INVALID_EXTRUDER "Extrudeur invalide"
-#define MSG_X_MIN "x_min: "
-#define MSG_X_MAX "x_max: "
-#define MSG_Y_MIN "y_min: "
-#define MSG_Y_MAX "y_max: "
-#define MSG_Z_MIN "z_min: "
-#define MSG_Z_MAX "z_max: "
-#define MSG_M119_REPORT "Affichage du status des fin de course"
-#define MSG_ENDSTOP_HIT "DECLENCHE"
-#define MSG_ENDSTOP_OPEN "OUVERT"
-#define MSG_HOTEND_OFFSET "Hotend offsets:"
-
-#define MSG_SD_CANT_OPEN_SUBDIR "Impossible d'ouvrir le sous-repertoire"
-#define MSG_SD_INIT_FAIL "Echec de l'initialisation de la SD"
-#define MSG_SD_VOL_INIT_FAIL "Echec de volume.init"
-#define MSG_SD_OPENROOT_FAIL "Echec openRoot"
-#define MSG_SD_CARD_OK "Carte SD Ok"
-#define MSG_SD_WORKDIR_FAIL "Echec d'ouverture workDir"
-#define MSG_SD_OPEN_FILE_FAIL "Echec d'ouverture, Fichier: "
-#define MSG_SD_FILE_OPENED "Fichier ouvert: "
-#define MSG_SD_SIZE " Taille: "
-#define MSG_SD_FILE_SELECTED "Fichier selectionne"
-#define MSG_SD_WRITE_TO_FILE "Ecriture dans le fichier: "
-#define MSG_SD_PRINTING_BYTE "Octet impression SD "
-#define MSG_SD_NOT_PRINTING "Pas d'impression SD"
-#define MSG_SD_ERR_WRITE_TO_FILE "Erreur d'ecriture dans le fichier"
-#define MSG_SD_CANT_ENTER_SUBDIR "Impossible d'entrer dans le sous-repertoire: "
-
-#define MSG_STEPPER_TOO_HIGH "Steprate trop eleve: "
-#define MSG_ENDSTOPS_HIT "Fin de course atteint: "
-#define MSG_ERR_COLD_EXTRUDE_STOP " Extrusion a froid evitee"
-#define MSG_ERR_LONG_EXTRUDE_STOP " Extrusion longue evitee"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 4
-
-// LCD Menu Messages
-
- #define WELCOME_MSG MACHINE_NAME " Bereit."
-
- #define MSG_SD_INSERTED "SDKarte erkannt"
- #define MSG_SD_REMOVED "SDKarte entfernt"
- #define MSG_MAIN "Hauptmenü"
- #define MSG_AUTOSTART "Autostart"
- #define MSG_DISABLE_STEPPERS "Stepper abschalten"
- #define MSG_AUTO_HOME "Auto Nullpunkt"
- #define MSG_SET_ORIGIN "Setze Nullpunkt"
- #define MSG_PREHEAT_PLA "Vorwärmen PLA"
- #define MSG_PREHEAT_PLA_SETTINGS "Vorwärmen PLA Einstellungen"
- #define MSG_PREHEAT_ABS "Vorwärmen ABS"
- #define MSG_PREHEAT_ABS_SETTINGS "Vorwärmen ABS Einstellungen"
- #define MSG_COOLDOWN "Abkühlen"
- #define MSG_EXTRUDE "Extrude"
- #define MSG_RETRACT "Retract"
- #define MSG_MOVE_AXIS "Achsen bewegen"
- #define MSG_SPEED "Geschw"
- #define MSG_NOZZLE "Düse"
- #define MSG_NOZZLE1 "Düse2"
- #define MSG_NOZZLE2 "Düse3"
- #define MSG_BED "Bett"
- #define MSG_FAN_SPEED "Lüftergeschw."
- #define MSG_FLOW "Fluss"
- #define MSG_CONTROL "Einstellungen"
- #define MSG_MIN "\002 Min"
- #define MSG_MAX "\002 Max"
- #define MSG_FACTOR "\002 Faktor"
- #define MSG_AUTOTEMP "AutoTemp"
- #define MSG_ON "Ein"
- #define MSG_OFF "Aus"
- #define MSG_PID_P "PID-P"
- #define MSG_PID_I "PID-I"
- #define MSG_PID_D "PID-D"
- #define MSG_PID_C "PID-C"
- #define MSG_ACC "Acc"
- #define MSG_VXY_JERK "Vxy-jerk"
- #define MSG_VZ_JERK "Vz-jerk"
- #define MSG_VE_JERK "Ve-jerk"
- #define MSG_VMAX "Vmax "
- #define MSG_X "x"
- #define MSG_Y "y"
- #define MSG_Z "z"
- #define MSG_E "e"
- #define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "VTrav min"
- #define MSG_AMAX "Amax "
- #define MSG_A_RETRACT "A-Retract"
- #define MSG_XSTEPS "Xsteps/mm"
- #define MSG_YSTEPS "Ysteps/mm"
- #define MSG_ZSTEPS "Zsteps/mm"
- #define MSG_ESTEPS "Esteps/mm"
- #define MSG_RECTRACT_WIDE "Rectract"
- #define MSG_WATCH "Beobachten"
- #define MSG_TEMPERATURE "Temperatur"
- #define MSG_MOTION "Bewegung"
- #define MSG_CONTRAST "LCD contrast"
- #define MSG_STORE_EPROM "EPROM speichern"
- #define MSG_LOAD_EPROM "EPROM laden"
- #define MSG_RESTORE_FAILSAFE "Standardkonfig."
- #define MSG_REFRESH "Aktualisieren"
- #define MSG_PREPARE "Vorbereitung"
- #define MSG_CONTROL "Einstellungen"
- #define MSG_TUNE "Justierung"
- #define MSG_PAUSE_PRINT "Druck anhalten"
- #define MSG_RESUME_PRINT "Druck fortsetz"
- #define MSG_STOP_PRINT "Druck stoppen"
- #define MSG_CARD_MENU "SDKarten Menü"
- #define MSG_NO_CARD "Keine SDKarte"
- #define MSG_DWELL "Warten..."
- #define MSG_USERWAIT "Warte auf Nutzer..."
- #define MSG_RESUMING "Druck fortsetzung"
- #define MSG_NO_MOVE "Kein Zug."
- #define MSG_PART_RELEASE "Stepper tlw frei"
- #define MSG_KILLED "KILLED"
- #define MSG_STOPPED "GESTOPPT"
- #define MSG_STEPPER_RELEASED "Stepper frei"
- #define MSG_CONTROL_RETRACT "Retract mm"
- #define MSG_CONTROL_RETRACTF "Retract F"
- #define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
- #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
- #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
- #define MSG_AUTORETRACT "AutoRetr."
- #define MSG_FILAMENTCHANGE "Filament wechseln"
-
-// Serial Console Messages
-
- #define MSG_Enqueing "enqueing \""
- #define MSG_POWERUP "PowerUp"
- #define MSG_EXTERNAL_RESET " External Reset"
- #define MSG_BROWNOUT_RESET " Brown out Reset"
- #define MSG_WATCHDOG_RESET " Watchdog Reset"
- #define MSG_SOFTWARE_RESET " Software Reset"
- #define MSG_MARLIN "Marlin: "
- #define MSG_AUTHOR " | Author: "
- #define MSG_CONFIGURATION_VER " Last Updated: "
- #define MSG_FREE_MEMORY " Free Memory: "
- #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "Done saving file."
- #define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
- #define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
- #define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
- #define MSG_FILE_PRINTED "Done printing file"
- #define MSG_BEGIN_FILE_LIST "Begin file list"
- #define MSG_END_FILE_LIST "End file list"
- #define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
- #define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
- #define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
- #define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
- #define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
- #define MSG_HEATING "Heating..."
- #define MSG_HEATING_COMPLETE "Heating done."
- #define MSG_BED_HEATING "Bed Heating."
- #define MSG_BED_DONE "Bed done."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Count X:"
- #define MSG_ERR_KILLED "Printer halted. kill() called !!"
- #define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart!"
- #define MSG_RESEND "Resend:"
- #define MSG_UNKNOWN_COMMAND "Unknown command:\""
- #define MSG_ACTIVE_EXTRUDER "Active Extruder: "
- #define MSG_INVALID_EXTRUDER "Invalid extruder"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Reporting endstop status"
- #define MSG_ENDSTOP_HIT "TRIGGERED"
- #define MSG_ENDSTOP_OPEN "open"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
- #define MSG_SD_INIT_FAIL "SD init fail"
- #define MSG_SD_VOL_INIT_FAIL "volume.init failed"
- #define MSG_SD_OPENROOT_FAIL "openRoot failed"
- #define MSG_SD_CARD_OK "SD card ok"
- #define MSG_SD_WORKDIR_FAIL "workDir open failed"
- #define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
- #define MSG_SD_FILE_OPENED "File opened:"
- #define MSG_SD_SIZE " Size:"
- #define MSG_SD_FILE_SELECTED "File selected"
- #define MSG_SD_WRITE_TO_FILE "Writing to file: "
- #define MSG_SD_PRINTING_BYTE "SD printing byte "
- #define MSG_SD_NOT_PRINTING "Not SD printing"
- #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
- #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
-
- #define MSG_STEPPER_TOO_HIGH "Steprate too high : "
- #define MSG_ENDSTOPS_HIT "endstops hit: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
- #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 5
-
-// LCD Menu Messages
-#define WELCOME_MSG MACHINE_NAME "Lista."
-#define MSG_SD_INSERTED "Tarjeta SD Colocada"
-#define MSG_SD_REMOVED "Tarjeta SD Retirada"
-#define MSG_MAIN "Menu Principal"
-#define MSG_AUTOSTART " Autostart"
-#define MSG_DISABLE_STEPPERS "Apagar Motores"
-#define MSG_AUTO_HOME "Llevar al Origen" // "Llevar Ejes al Cero"
-#define MSG_SET_ORIGIN "Establecer Cero"
-#define MSG_PREHEAT_PLA "Precalentar PLA"
-#define MSG_PREHEAT_PLA_SETTINGS "Ajustar temp. PLA"
-#define MSG_PREHEAT_ABS "Precalentar ABS"
-#define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
-#define MSG_COOLDOWN "Enfriar"
-#define MSG_EXTRUDE "Extruir"
-#define MSG_RETRACT "Retraer"
-#define MSG_MOVE_AXIS "Mover Ejes"
-#define MSG_SPEED "Velocidad"
-#define MSG_NOZZLE "Nozzle"
-#define MSG_NOZZLE1 "Nozzle2"
-#define MSG_NOZZLE2 "Nozzle3"
-#define MSG_BED "Base"
-#define MSG_FAN_SPEED "Ventilador"
-#define MSG_FLOW "Flujo"
-#define MSG_CONTROL "Control"
-#define MSG_MIN "\002 Min"
-#define MSG_MAX "\002 Max"
-#define MSG_FACTOR "\002 Fact"
-#define MSG_AUTOTEMP "Autotemp"
-#define MSG_ON "On"
-#define MSG_OFF "Off"
-#define MSG_PID_P "PID-P"
-#define MSG_PID_I "PID-I"
-#define MSG_PID_D "PID-D"
-#define MSG_PID_C "PID-C"
-#define MSG_ACC "Acel"
-#define MSG_VXY_JERK "Vxy-jerk"
-#define MSG_VZ_JERK "Vz-jerk"
-#define MSG_VE_JERK "Ve-jerk"
-#define MSG_VMAX "Vmax"
-#define MSG_X "x"
-#define MSG_Y "y"
-#define MSG_Z "z"
-#define MSG_E "e"
-#define MSG_VMIN "Vmin"
-#define MSG_VTRAV_MIN "VTrav min"
-#define MSG_AMAX "Amax"
-#define MSG_A_RETRACT "A-retrac."
-#define MSG_XSTEPS "X pasos/mm"
-#define MSG_YSTEPS "Y pasos/mm"
-#define MSG_ZSTEPS "Z pasos/mm"
-#define MSG_ESTEPS "E pasos/mm"
-#define MSG_RECTRACT "Retraer"
-#define MSG_TEMPERATURE "Temperatura"
-#define MSG_MOTION "Movimiento"
-#define MSG_STORE_EPROM "Guardar Memoria"
-#define MSG_LOAD_EPROM "Cargar Memoria"
-#define MSG_RESTORE_FAILSAFE "Rest. de emergencia"
-#define MSG_REFRESH "Volver a cargar"
-#define MSG_WATCH "Monitorizar"
-#define MSG_PREPARE "Preparar"
-#define MSG_TUNE "Ajustar"
-#define MSG_PAUSE_PRINT "Pausar Impresion"
-#define MSG_RESUME_PRINT "Reanudar Impresion"
-#define MSG_STOP_PRINT "Detener Impresion"
-#define MSG_CARD_MENU "Menu de SD"
-#define MSG_NO_CARD "No hay Tarjeta SD"
-#define MSG_DWELL "Reposo..."
-#define MSG_USERWAIT "Esperando Ordenes..."
-#define MSG_RESUMING "Resumiendo Impresion"
-#define MSG_NO_MOVE "Sin movimiento"
-#define MSG_KILLED "PARADA DE EMERGENCIA. "
-#define MSG_STOPPED "PARADA."
-#define MSG_CONTROL_RETRACT "Retraer mm"
-#define MSG_CONTROL_RETRACTF "Retraer F"
-#define MSG_CONTROL_RETRACT_ZLIFT "Levantar mm"
-#define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm"
-#define MSG_CONTROL_RETRACT_RECOVERF "DesRet F"
-#define MSG_AUTORETRACT "AutoRetr."
-#define MSG_FILAMENTCHANGE "Change filament"
-#define MSG_INIT_SDCARD "Iniciando. Tarjeta-SD"
-#define MSG_CNG_SDCARD "Cambiar Tarjeta-SD"
-#define MSG_RECTRACT_WIDE "Retraer"
-#define MSG_TEMPERATURE_WIDE "Temperatura"
-#define MSG_TEMPERATURE_RTN "Temperatura"
-#define MSG_MAIN_WIDE "Menu Principal"
-#define MSG_MOTION_WIDE "Movimiento"
-#define MSG_PREPARE_ALT "Preparar"
-#define MSG_CONTROL_ARROW "Control"
-#define MSG_RETRACT_ARROW "Retraer"
-#define MSG_PART_RELEASE "Desacople Parcial"
-#define MSG_STEPPER_RELEASED "Desacoplada."
-
-// Serial Console Messages
-
-#define MSG_Enqueing "En cola \""
-#define MSG_POWERUP "PowerUp"
-#define MSG_EXTERNAL_RESET " Reset Externo"
-#define MSG_BROWNOUT_RESET " Reset por Voltaje Incorrecto"
-#define MSG_WATCHDOG_RESET " Reset por Bloqueo"
-#define MSG_SOFTWARE_RESET " Reset por Software"
-#define MSG_MARLIN "Marlin "
-#define MSG_AUTHOR " | Autor: "
-#define MSG_CONFIGURATION_VER " Ultima actualizacion: "
-#define MSG_FREE_MEMORY " Memoria libre: "
-#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
-#define MSG_OK "ok"
-#define MSG_FILE_SAVED "Guardado."
-#define MSG_ERR_LINE_NO "El Numero de Linea no es igual al Ultimo Numero de Linea+1, Ultima Linea:"
-#define MSG_ERR_CHECKSUM_MISMATCH "el checksum no coincide, Ultima Linea:"
-#define MSG_ERR_NO_CHECKSUM "No se pudo hallar el Checksum con el numero de linea, Ultima Linea:"
-#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No se hallo el Numero de Linea con el Checksum, Ultima Linea:"
-#define MSG_FILE_PRINTED "Impresion terminada"
-#define MSG_BEGIN_FILE_LIST "Comienzo de la lista de archivos"
-#define MSG_END_FILE_LIST "Fin de la lista de archivos"
-#define MSG_M104_INVALID_EXTRUDER "M104 Extrusor Invalido "
-#define MSG_M105_INVALID_EXTRUDER "M105 Extrusor Invalido "
-#define MSG_M218_INVALID_EXTRUDER "M218 Extrusor Invalido "
-#define MSG_ERR_NO_THERMISTORS "No hay termistores - no temp"
-#define MSG_M109_INVALID_EXTRUDER "M109 Extrusor Invalido "
-#define MSG_HEATING "Calentando..."
-#define MSG_HEATING_COMPLETE "Calentamiento Hecho."
-#define MSG_BED_HEATING "Calentando la base."
-#define MSG_BED_DONE "Base Caliente."
-#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
-#define MSG_COUNT_X " Cuenta X:"
-#define MSG_ERR_KILLED "¡¡Impresora Parada con kill()!!"
-#define MSG_ERR_STOPPED "¡Impresora parada por errores. Arregle el error y use M999 Para reiniciar!. (La temperatura se reestablece. Ajustela antes de continuar)"
-#define MSG_RESEND "Reenviar:"
-#define MSG_UNKNOWN_COMMAND "Comando Desconocido:\""
-#define MSG_ACTIVE_EXTRUDER "Extrusor Activo: "
-#define MSG_INVALID_EXTRUDER "Extrusor Invalido"
-#define MSG_X_MIN "x_min: "
-#define MSG_X_MAX "x_max: "
-#define MSG_Y_MIN "y_min: "
-#define MSG_Y_MAX "y_max: "
-#define MSG_Z_MIN "z_min: "
-#define MSG_Z_MAX "z_max: "
-#define MSG_M119_REPORT "Comprobando fines de carrera."
-#define MSG_ENDSTOP_HIT "PULSADO"
-#define MSG_ENDSTOP_OPEN "abierto"
-#define MSG_HOTEND_OFFSET "Hotend offsets:"
-#define MSG_SD_CANT_OPEN_SUBDIR "No se pudo abrir la subcarpeta."
-#define MSG_SD_INIT_FAIL "Fallo al iniciar la SD"
-#define MSG_SD_VOL_INIT_FAIL "Fallo al montar el volumen"
-#define MSG_SD_OPENROOT_FAIL "Fallo al abrir la carpeta raiz"
-#define MSG_SD_CARD_OK "Tarjeta SD OK"
-#define MSG_SD_WORKDIR_FAIL "Fallo al abrir la carpeta de trabajo"
-#define MSG_SD_OPEN_FILE_FAIL "Error al abrir, Archivo: "
-#define MSG_SD_FILE_OPENED "Archivo abierto:"
-#define MSG_SD_SIZE " Tamaño:"
-#define MSG_SD_FILE_SELECTED "Archivo Seleccionado"
-#define MSG_SD_WRITE_TO_FILE "Escribiendo en el archivo: "
-#define MSG_SD_PRINTING_BYTE "SD imprimiendo el byte "
-#define MSG_SD_NOT_PRINTING "No se esta imprimiendo con SD"
-#define MSG_SD_ERR_WRITE_TO_FILE "Error al escribir en el archivo"
-#define MSG_SD_CANT_ENTER_SUBDIR "No se puede abrir la carpeta:"
-
-#define MSG_STEPPER_TOO_HIGH "Steprate demasiado alto : "
-#define MSG_ENDSTOPS_HIT "Se ha tocado el fin de carril: "
-#define MSG_ERR_COLD_EXTRUDE_STOP " extrusion fria evitada"
-#define MSG_ERR_LONG_EXTRUDE_STOP " extrusion demasiado larga evitada"
-
-#endif
-
-#if LANGUAGE_CHOICE == 6
-
-// LCD Menu Messages
-#define WELCOME_MSG MACHINE_NAME " Готов"
-#define MSG_SD_INSERTED "Карта вставлена"
-#define MSG_SD_REMOVED "Карта извлечена"
-#define MSG_MAIN " Меню \003"
-#define MSG_AUTOSTART " Автостарт "
-#define MSG_DISABLE_STEPPERS " Выключить двигатели"
-#define MSG_AUTO_HOME " Парковка "
-#define MSG_SET_ORIGIN " Запомнить ноль "
-#define MSG_PREHEAT_PLA " Преднагрев PLA "
-#define MSG_PREHEAT_PLA_SETTINGS " Настр. преднагр.PLA"
-#define MSG_PREHEAT_ABS " Преднагрев ABS "
-#define MSG_PREHEAT_ABS_SETTINGS " Настр. преднагр.ABS"
-#define MSG_COOLDOWN " Охлаждение "
-#define MSG_EXTRUDE " Экструзия "
-#define MSG_RETRACT " Откат"
-#define MSG_MOVE_AXIS " Движение по осям \x7E"
-#define MSG_SPEED " Скорость:"
-#define MSG_NOZZLE " \002 Фильера:"
-#define MSG_NOZZLE1 " \002 Фильера2:"
-#define MSG_NOZZLE2 " \002 Фильера3:"
-#define MSG_BED " \002 Кровать:"
-#define MSG_FAN_SPEED " Куллер:"
-#define MSG_FLOW " Поток:"
-#define MSG_CONTROL " Настройки \003"
-#define MSG_MIN " \002 Минимум:"
-#define MSG_MAX " \002 Максимум:"
-#define MSG_FACTOR " \002 Фактор:"
-#define MSG_AUTOTEMP " Autotemp:"
-#define MSG_ON "Вкл. "
-#define MSG_OFF "Выкл. "
-#define MSG_PID_P " PID-P: "
-#define MSG_PID_I " PID-I: "
-#define MSG_PID_D " PID-D: "
-#define MSG_PID_C " PID-C: "
-#define MSG_ACC " Acc:"
-#define MSG_VXY_JERK " Vxy-jerk: "
-#define MSG_VZ_JERK "Vz-jerk"
-#define MSG_VE_JERK "Ve-jerk"
-#define MSG_VMAX " Vmax "
-#define MSG_X "x:"
-#define MSG_Y "y:"
-#define MSG_Z "z:"
-#define MSG_E "e:"
-#define MSG_VMIN " Vmin:"
-#define MSG_VTRAV_MIN " VTrav min:"
-#define MSG_AMAX " Amax "
-#define MSG_A_RETRACT " A-retract:"
-#define MSG_XSTEPS " X шаг/mm:"
-#define MSG_YSTEPS " Y шаг/mm:"
-#define MSG_ZSTEPS " Z шаг/mm:"
-#define MSG_ESTEPS " E шаг/mm:"
-#define MSG_RECTRACT " Откат подачи \x7E"
-#define MSG_TEMPERATURE " Температура \x7E"
-#define MSG_MOTION " Скорости \x7E"
- #define MSG_CONTRAST "LCD contrast"
-#define MSG_STORE_EPROM " Сохранить настройки"
-#define MSG_LOAD_EPROM " Загрузить настройки"
-#define MSG_RESTORE_FAILSAFE " Сброс настроек "
-#define MSG_REFRESH "\004Обновить "
-#define MSG_WATCH " Обзор \003"
-#define MSG_PREPARE " Действия \x7E"
-#define MSG_TUNE " Настройки \x7E"
-#define MSG_PAUSE_PRINT " Пауза печати \x7E"
-#define MSG_RESUME_PRINT " Продолжить печать \x7E"
-#define MSG_STOP_PRINT " Остановить печать \x7E"
-#define MSG_CARD_MENU " Меню карты \x7E"
-#define MSG_NO_CARD " Нет карты"
-#define MSG_DWELL "Сон..."
-#define MSG_USERWAIT "Нажмите для продолж."
-#define MSG_NO_MOVE "Нет движения. "
-#define MSG_PART_RELEASE " Извлечение принта "
-#define MSG_KILLED "УБИТО. "
-#define MSG_STOPPED "ОСТАНОВЛЕНО. "
-#define MSG_CONTROL_RETRACT " Откат mm:"
-#define MSG_CONTROL_RETRACTF " Откат F:"
-#define MSG_CONTROL_RETRACT_ZLIFT " Прыжок mm:"
-#define MSG_CONTROL_RETRACT_RECOVER " Возврат +mm:"
-#define MSG_CONTROL_RETRACT_RECOVERF " Возврат F:"
-#define MSG_AUTORETRACT " АвтоОткат:"
-#define MSG_FILAMENTCHANGE "Change filament"
-
-// Serial Console Messages
-
-#define MSG_Enqueing "Запланировано \""
-#define MSG_POWERUP "Включение питания"
-#define MSG_EXTERNAL_RESET " Внешний сброс"
-#define MSG_BROWNOUT_RESET " Brown out сброс"
-#define MSG_WATCHDOG_RESET " Watchdog сброс"
-#define MSG_SOFTWARE_RESET " программный сброс"
-#define MSG_MARLIN "Marlin "
-#define MSG_AUTHOR " | Автор: "
-#define MSG_CONFIGURATION_VER " Последнее обновление: "
-#define MSG_FREE_MEMORY " Памяти свободно: "
-#define MSG_PLANNER_BUFFER_BYTES " Буффер очереди команд Bytes: "
-#define MSG_OK "ok"
-#define MSG_FILE_SAVED "Файл записан."
-#define MSG_ERR_LINE_NO "Номен строки это не последняя строка+1, последняя строка:"
-#define MSG_ERR_CHECKSUM_MISMATCH "контрольная сумма не совпадает, последняя строка:"
-#define MSG_ERR_NO_CHECKSUM "нет контрольной суммы для строки, последняя строка:"
-#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "нет строки для контрольной суммы, последняя строка:"
-#define MSG_FILE_PRINTED "Печать файла завершена"
-#define MSG_BEGIN_FILE_LIST "Список файлов"
-#define MSG_END_FILE_LIST "Конец списка файлов"
-#define MSG_M104_INVALID_EXTRUDER "M104 ошибка экструдера "
-#define MSG_M105_INVALID_EXTRUDER "M105 ошибка экструдера "
-#define MSG_M218_INVALID_EXTRUDER "M218 ошибка экструдера "
-#define MSG_ERR_NO_THERMISTORS "Нет термистра - нет температуры"
-#define MSG_M109_INVALID_EXTRUDER "M109 ошибка экструдера "
-#define MSG_HEATING "Нагрев... "
-#define MSG_HEATING_COMPLETE "Наргето. "
-#define MSG_BED_HEATING "Нагрев стола... "
-#define MSG_BED_DONE "Стол нагрет. "
-#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
-#define MSG_COUNT_X " Count X:"
-#define MSG_ERR_KILLED "Принтер остановлен. вызов kill() !!"
-#define MSG_ERR_STOPPED "Ошибка принтера, останов. Устраните неисправность и используйте M999 для перезагрузки!. (Температура недоступна. Проверьте датчики)"
-#define MSG_RESEND "Переотправка:"
-#define MSG_UNKNOWN_COMMAND "Неизвестная команда:\""
-#define MSG_ACTIVE_EXTRUDER "Активный экструдер: "
-#define MSG_INVALID_EXTRUDER "Ошибка экструдера"
-#define MSG_X_MIN "x_min:"
-#define MSG_X_MAX "x_max:"
-#define MSG_Y_MIN "y_min:"
-#define MSG_Y_MAX "y_max:"
-#define MSG_Z_MIN "z_min:"
-#define MSG_Z_MAX "z_max:"
-#define MSG_M119_REPORT "Статус концевиков"
-#define MSG_ENDSTOP_HIT "Срабатывание концевика"
-#define MSG_ENDSTOP_OPEN "Концевик освобожден"
-#define MSG_HOTEND_OFFSET "Hotend offsets:"
-#define MSG_SD_CANT_OPEN_SUBDIR "Не открыть папку"
-#define MSG_SD_INIT_FAIL "Ошибка инициализации SD"
-#define MSG_SD_VOL_INIT_FAIL "Ошибка инициализации раздела"
-#define MSG_SD_OPENROOT_FAIL "Не прочесть содержимое корня"
-#define MSG_SD_CARD_OK "SD карта в порядке"
-#define MSG_SD_WORKDIR_FAIL "не открыть рабочую папку"
-#define MSG_SD_OPEN_FILE_FAIL "Ошибка чтения, файл: "
-#define MSG_SD_FILE_OPENED "Файл открыт:"
-#define MSG_SD_SIZE " Размер:"
-#define MSG_SD_FILE_SELECTED "Файл выбран"
-#define MSG_SD_WRITE_TO_FILE "Запись в файл: "
-#define MSG_SD_PRINTING_BYTE "SD печать byte "
-#define MSG_SD_NOT_PRINTING "нет SD печати"
-#define MSG_SD_ERR_WRITE_TO_FILE "ошибка записи в файл"
-#define MSG_SD_CANT_ENTER_SUBDIR "Не зайти в папку:"
-#define MSG_STEPPER_TOO_HIGH "Частота шагов очень высока : "
-#define MSG_ENDSTOPS_HIT "концевик сработал: "
-#define MSG_ERR_COLD_EXTRUDE_STOP " защита холодной экструзии"
-#define MSG_ERR_LONG_EXTRUDE_STOP " защита превышения длинны экструзии"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 7
-
- // LCD Menu Messages
- #define WELCOME_MSG MACHINE_NAME " Pronta"
- #define MSG_SD_INSERTED "SD Card inserita"
- #define MSG_SD_REMOVED "SD Card rimossa"
- #define MSG_MAIN "Menu principale"
- #define MSG_AUTOSTART "Autostart"
- #define MSG_DISABLE_STEPPERS "Disabilita Motori"
- #define MSG_AUTO_HOME "Auto Home"
- #define MSG_SET_ORIGIN "Imposta Origine"
- #define MSG_PREHEAT_PLA "Preriscalda PLA"
- #define MSG_PREHEAT_PLA_SETTINGS "Preris. PLA Conf"
- #define MSG_PREHEAT_ABS "Preriscalda ABS"
- #define MSG_PREHEAT_ABS_SETTINGS "Preris. ABS Conf"
- #define MSG_COOLDOWN "Raffredda"
- #define MSG_EXTRUDE "Estrudi"
- #define MSG_RETRACT "Ritrai"
- #define MSG_MOVE_AXIS "Muovi Asse"
- #define MSG_SPEED "Velcità"
- #define MSG_NOZZLE "Ugello"
- #define MSG_NOZZLE1 "Ugello2"
- #define MSG_NOZZLE2 "Ugello3"
- #define MSG_BED "Piatto"
- #define MSG_FAN_SPEED "Ventola"
- #define MSG_FLOW "Flusso"
- #define MSG_CONTROL "Controllo"
- #define MSG_MIN " \002 Min:"
- #define MSG_MAX " \002 Max:"
- #define MSG_FACTOR " \002 Fact:"
- #define MSG_AUTOTEMP "Autotemp"
- #define MSG_ON "On "
- #define MSG_OFF "Off"
- #define MSG_PID_P "PID-P"
- #define MSG_PID_I "PID-I"
- #define MSG_PID_D "PID-D"
- #define MSG_PID_C "PID-C"
- #define MSG_ACC "Accel"
- #define MSG_VXY_JERK "Vxy-jerk"
- #define MSG_VZ_JERK "Vz-jerk"
- #define MSG_VE_JERK "Ve-jerk"
- #define MSG_VMAX "Vmax"
- #define MSG_X "x"
- #define MSG_Y "y"
- #define MSG_Z "z"
- #define MSG_E "e"
- #define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "VTrav min"
- #define MSG_AMAX "Amax"
- #define MSG_A_RETRACT "A-retract"
- #define MSG_XSTEPS "Xpassi/mm"
- #define MSG_YSTEPS "Ypassi/mm"
- #define MSG_ZSTEPS "Zpassi/mm"
- #define MSG_ESTEPS "Epassi/mm"
- #define MSG_RECTRACT "Ritrai"
- #define MSG_TEMPERATURE "Temperatura"
- #define MSG_MOTION "Movimento"
- #define MSG_CONTRAST "LCD contrast"
- #define MSG_STORE_EPROM "Salva in EEPROM"
- #define MSG_LOAD_EPROM "Carica da EEPROM"
- #define MSG_RESTORE_FAILSAFE "Impostaz. default"
- #define MSG_REFRESH "Aggiorna"
- #define MSG_WATCH "Guarda"
- #define MSG_PREPARE "Prepara"
- #define MSG_TUNE "Adatta"
- #define MSG_PAUSE_PRINT "Pausa"
- #define MSG_RESUME_PRINT "Riprendi Stampa"
- #define MSG_STOP_PRINT "Arresta Stampa"
- #define MSG_CARD_MENU "SD Card Menu"
- #define MSG_NO_CARD "No SD Card"
- #define MSG_DWELL "Sospensione..."
- #define MSG_USERWAIT "Attendi Utente..."
- #define MSG_RESUMING "Riprendi Stampa"
- #define MSG_NO_MOVE "Nessun Movimento."
- #define MSG_KILLED "UCCISO. "
- #define MSG_STOPPED "ARRESTATO. "
- #define MSG_CONTROL_RETRACT "Ritrai mm"
- #define MSG_CONTROL_RETRACTF "Ritrai F"
- #define MSG_CONTROL_RETRACT_ZLIFT "Salta mm"
- #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
- #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
- #define MSG_AUTORETRACT "AutoArretramento"
- #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Qualcosa non va in MenuStructure."
- #define MSG_FILAMENTCHANGE "Cambia filamento"
- #define MSG_INIT_SDCARD "Iniz. SD-Card"
- #define MSG_CNG_SDCARD "Cambia SD-Card"
-
- // Serial Console Messages
-
- #define MSG_Enqueing "accodamento \""
- #define MSG_POWERUP "Accensione"
- #define MSG_EXTERNAL_RESET " Reset Esterno"
- #define MSG_BROWNOUT_RESET " Brown out Reset"
- #define MSG_WATCHDOG_RESET " Watchdog Reset"
- #define MSG_SOFTWARE_RESET " Software Reset"
- #define MSG_MARLIN "Marlin "
- #define MSG_AUTHOR " | Autore: "
- #define MSG_CONFIGURATION_VER " Ultimo Aggiornamento: "
- #define MSG_FREE_MEMORY " Memoria Libera: "
- #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "File Salvato."
- #define MSG_ERR_LINE_NO "Il Numero della Linea non corrisponde al Numero dell'Ultima Linea+1, Ultima Linea: "
- #define MSG_ERR_CHECKSUM_MISMATCH "checksum non corrispondente, Ultima Linea: "
- #define MSG_ERR_NO_CHECKSUM "Nessun Checksum con Numero di Linea, Ultima Linea: "
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Nessun Numero di Linea con Checksum, Ultima Linea: "
- #define MSG_FILE_PRINTED "File stampato"
- #define MSG_BEGIN_FILE_LIST "Inizio Lista File"
- #define MSG_END_FILE_LIST "Fine Lista File"
- #define MSG_M104_INVALID_EXTRUDER "M104 Estrusore non valido "
- #define MSG_M105_INVALID_EXTRUDER "M105 Estrusore non valido "
- #define MSG_M218_INVALID_EXTRUDER "M218 Estrusore non valido "
- #define MSG_ERR_NO_THERMISTORS "Nessun Termistore - nessuna temperatura"
- #define MSG_M109_INVALID_EXTRUDER "M109 Estrusore non valido "
- #define MSG_HEATING "Riscaldamento..."
- #define MSG_HEATING_COMPLETE "Stampante Calda."
- #define MSG_BED_HEATING "Riscaldamento Piatto."
- #define MSG_BED_DONE "Piatto Pronto."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Calcola X: "
- #define MSG_ERR_KILLED "Stampante Calda. kill() chiamata !!"
- #define MSG_ERR_STOPPED "Stampante fermata a causa di errori. Risolvi l'errore e usa M999 per ripartire!. (Reset temperatura. Impostala prima di ripartire)"
- #define MSG_RESEND "Reinviato:"
- #define MSG_UNKNOWN_COMMAND "Comando sconosciuto: \""
- #define MSG_ACTIVE_EXTRUDER "Attiva Estrusore: "
- #define MSG_INVALID_EXTRUDER "Estrusore non valido"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Segnalazione stato degli endstop"
- #define MSG_ENDSTOP_HIT "INNESCATO"
- #define MSG_ENDSTOP_OPEN "aperto"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Impossibile aprire sottocartella"
- #define MSG_SD_INIT_FAIL "Fallita Inizializzazione SD"
- #define MSG_SD_VOL_INIT_FAIL "Fallito il montaggio del Volume"
- #define MSG_SD_OPENROOT_FAIL "Fallita l'apertura Cartella Principale"
- #define MSG_SD_CARD_OK "SD card ok"
- #define MSG_SD_WORKDIR_FAIL "Fallita l'apertura Cartella di Lavoro"
- #define MSG_SD_OPEN_FILE_FAIL "Fallita l'apertura del File: "
- #define MSG_SD_FILE_OPENED "File aperto: "
- #define MSG_SD_SIZE " Dimensione: "
- #define MSG_SD_FILE_SELECTED "File selezionato"
- #define MSG_SD_WRITE_TO_FILE "Scrittura su file: "
- #define MSG_SD_PRINTING_BYTE "Si sta scrivendo il byte su SD "
- #define MSG_SD_NOT_PRINTING "Non si sta scrivendo su SD"
- #define MSG_SD_ERR_WRITE_TO_FILE "Errore nella scrittura su file"
- #define MSG_SD_CANT_ENTER_SUBDIR "Impossibile entrare nella sottocartella: "
-
- #define MSG_STEPPER_TOO_HIGH "Steprate troppo alto: "
- #define MSG_ENDSTOPS_HIT "Raggiunto il fondo carrello: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " prevenuta estrusione fredda"
- #define MSG_ERR_LONG_EXTRUDE_STOP " prevenuta estrusione troppo lunga"
-
-#endif
-
-
-#if LANGUAGE_CHOICE == 8
-
-// LCD Menu Messages
- #define WELCOME_MSG MACHINE_NAME " Pronta."
- #define MSG_SD_INSERTED "Cartao SD inserido"
- #define MSG_SD_REMOVED "Cartao SD removido"
- #define MSG_MAIN " Menu Principal \003"
- #define MSG_AUTOSTART " Autostart"
- #define MSG_DISABLE_STEPPERS " Apagar Motores"
- #define MSG_AUTO_HOME " Ir para Origen"
- #define MSG_SET_ORIGIN " Estabelecer Origen"
- #define MSG_PREHEAT_PLA " pre-aquecer PLA"
- #define MSG_PREHEAT_PLA_SETTINGS " pre-aquecer PLA Setting"
- #define MSG_PREHEAT_ABS " pre-aquecer ABS"
- #define MSG_PREHEAT_ABS_SETTINGS " pre-aquecer ABS Setting"
- #define MSG_COOLDOWN " Esfriar"
- #define MSG_EXTRUDE " Extrudar"
- #define MSG_RETRACT " Retrair"
- #define MSG_PREHEAT_PLA " pre-aquecer PLA"
- #define MSG_PREHEAT_ABS " pre-aquecer ABS"
- #define MSG_MOVE_AXIS " Mover eixo \x7E"
- #define MSG_SPEED " Velocidade:"
- #define MSG_NOZZLE " \002Nozzle:"
- #define MSG_NOZZLE1 " \002Nozzle2:"
- #define MSG_NOZZLE2 " \002Nozzle3:"
- #define MSG_BED " \002Base:"
- #define MSG_FAN_SPEED " Velocidade Ventoinha:"
- #define MSG_FLOW " Fluxo:"
- #define MSG_CONTROL " Controle \003"
- #define MSG_MIN " \002 Min:"
- #define MSG_MAX " \002 Max:"
- #define MSG_FACTOR " \002 Fact:"
- #define MSG_AUTOTEMP " Autotemp:"
- #define MSG_ON "On "
- #define MSG_OFF "Off"
- #define MSG_PID_P " PID-P: "
- #define MSG_PID_I " PID-I: "
- #define MSG_PID_D " PID-D: "
- #define MSG_PID_C " PID-C: "
- #define MSG_ACC " Acc:"
- #define MSG_VXY_JERK " Vxy-jerk: "
- #define MSG_VZ_JERK "Vz-jerk"
- #define MSG_VE_JERK "Ve-jerk"
- #define MSG_VMAX " Vmax "
- #define MSG_X "x:"
- #define MSG_Y "y:"
- #define MSG_Z "z:"
- #define MSG_E "e:"
- #define MSG_VMIN " Vmin:"
- #define MSG_VTRAV_MIN " VTrav min:"
- #define MSG_AMAX " Amax "
- #define MSG_A_RETRACT " A-retract:"
- #define MSG_XSTEPS " Xpasso/mm:"
- #define MSG_YSTEPS " Ypasso/mm:"
- #define MSG_ZSTEPS " Zpasso/mm:"
- #define MSG_ESTEPS " Epasso/mm:"
- #define MSG_MAIN_WIDE " Menu Principal \003"
- #define MSG_RECTRACT_WIDE " Retrair \x7E"
- #define MSG_TEMPERATURE_WIDE " Temperatura \x7E"
- #define MSG_TEMPERATURE_RTN " Temperatura \003"
- #define MSG_MOTION_WIDE " Movimento \x7E"
- #define MSG_STORE_EPROM " Guardar memoria"
- #define MSG_LOAD_EPROM " Carregar memoria"
- #define MSG_RESTORE_FAILSAFE " Rest. de emergencia"
- #define MSG_REFRESH "\004Recarregar"
- #define MSG_WATCH " Monitorar \003"
- #define MSG_PREPARE " Preparar \x7E"
- #define MSG_PREPARE_ALT " Preparar \003"
- #define MSG_CONTROL_ARROW " Controle \x7E"
- #define MSG_RETRACT_ARROW " Retrair \x7E"
- #define MSG_TUNE " Tune \x7E"
- #define MSG_PAUSE_PRINT " Pausar Impressao \x7E"
- #define MSG_RESUME_PRINT " Resumir Impressao \x7E"
- #define MSG_STOP_PRINT " Parar Impressao \x7E"
- #define MSG_CARD_MENU " Menu cartao SD \x7E"
- #define MSG_NO_CARD " Sem cartao SD"
- #define MSG_DWELL "Repouso..."
- #define MSG_USERWAIT "Esperando Ordem..."
- #define MSG_NO_MOVE "Sem movimento."
- #define MSG_PART_RELEASE "Lancamento Parcial"
- #define MSG_KILLED "PARADA DE EMERGENCIA. "
- #define MSG_STOPPED "PARADA. "
- #define MSG_STEPPER_RELEASED "Lancado."
- #define MSG_CONTROL_RETRACT " Retrair mm:"
- #define MSG_CONTROL_RETRACTF " Retrair F:"
- #define MSG_CONTROL_RETRACT_ZLIFT " Levantar mm:"
- #define MSG_CONTROL_RETRACT_RECOVER " DesRet +mm:"
- #define MSG_CONTROL_RETRACT_RECOVERF " DesRet F:"
- #define MSG_AUTORETRACT " AutoRetr.:"
- #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Algo esta errado na estrutura do Menu."
- #define MSG_FILAMENTCHANGE "Change filament"
-
-// Serial Console Messages
-
- #define MSG_Enqueing "enqueing \""
- #define MSG_POWERUP "PowerUp"
- #define MSG_EXTERNAL_RESET " Reset Externo"
- #define MSG_BROWNOUT_RESET " Reset por voltagem incorreta"
- #define MSG_WATCHDOG_RESET " Reset por Bloqueio"
- #define MSG_SOFTWARE_RESET " Reset por Software"
- #define MSG_MARLIN "Marlin "
- #define MSG_AUTHOR " | Author: "
- #define MSG_CONFIGURATION_VER " Ultima atualizacao: "
- #define MSG_FREE_MEMORY " memoria Livre: "
- #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "Guardado."
- #define MSG_ERR_LINE_NO "O Numero da linha Nao e igual ao ultimo Numero da linha+1, Ultima linha:"
- #define MSG_ERR_CHECKSUM_MISMATCH "O checksum Nao coincide, Ultima linha:"
- #define MSG_ERR_NO_CHECKSUM "Nao foi possivel encontrar o checksum com o numero da linha, Ultima linha :"
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Nao ha o numero da linha com o checksum, Ultima linha:"
- #define MSG_FILE_PRINTED "Impressao terminada"
- #define MSG_BEGIN_FILE_LIST "Começo da lista de arquivos"
- #define MSG_END_FILE_LIST "Fim da lista de arquivos"
- #define MSG_M104_INVALID_EXTRUDER "M104 Extrusor inválido "
- #define MSG_M105_INVALID_EXTRUDER "M105 Extrusor inválido "
- #define MSG_M218_INVALID_EXTRUDER "M218 Extrusor inválido "
- #define MSG_ERR_NO_THERMISTORS "Nao ha termistor - no temp"
- #define MSG_M109_INVALID_EXTRUDER "M109 Extrusor inválido "
- #define MSG_HEATING "Aquecendo..."
- #define MSG_HEATING_COMPLETE "Aquecido."
- #define MSG_BED_HEATING "Aquecendo a Base."
- #define MSG_BED_DONE "Base quente."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Conta X:"
- #define MSG_ERR_KILLED "Impressora parada com kill() !!"
- #define MSG_ERR_STOPPED "Impressora parada por erros. Coserte o erro e use M999 para recomeçar!. (Temperatura reiniciada. Ajuste antes de recomeçar)"
- #define MSG_RESEND "Reenviar:"
- #define MSG_UNKNOWN_COMMAND "Comando desconhecido:\""
- #define MSG_ACTIVE_EXTRUDER "Extrusor ativo: "
- #define MSG_INVALID_EXTRUDER "Extrusor invalido"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Relatando estado do ponto final"
- #define MSG_ENDSTOP_HIT "PULSADO"
- #define MSG_ENDSTOP_OPEN "Aberto"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Nao pode abrir sub diretorio"
- #define MSG_SD_INIT_FAIL "Falha ao iniciar SD"
- #define MSG_SD_VOL_INIT_FAIL "Falha ao montar volume"
- #define MSG_SD_OPENROOT_FAIL "Falha ao abrir diretorio raiz"
- #define MSG_SD_CARD_OK "cartao SD ok"
- #define MSG_SD_WORKDIR_FAIL "Falha ao abrir diretorio de trabalho"
- #define MSG_SD_OPEN_FILE_FAIL "Erro ao abrir, Arquivo: "
- #define MSG_SD_FILE_OPENED "Arquivo aberto:"
- #define MSG_SD_SIZE " Size:"
- #define MSG_SD_FILE_SELECTED "Arquivo selecionado"
- #define MSG_SD_WRITE_TO_FILE "Escrevendo no arquivo: "
- #define MSG_SD_PRINTING_BYTE "SD imprimindo o byte "
- #define MSG_SD_NOT_PRINTING "Nao esta se imprimindo com o SD"
- #define MSG_SD_ERR_WRITE_TO_FILE "Erro ao escrever no arquivo"
- #define MSG_SD_CANT_ENTER_SUBDIR "Nao pode abrir o sub diretorio:"
-
- #define MSG_STEPPER_TOO_HIGH "Steprate muito alto : "
- #define MSG_ENDSTOPS_HIT "O ponto final foi tocado: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " Extrusao a frio evitada"
- #define MSG_ERR_LONG_EXTRUDE_STOP " Extrusao muito larga evitada"
-
-
-#endif
-
-
-
-#if LANGUAGE_CHOICE == 9
-
-// Finnish
-
-// LCD Menu Messages
- #define WELCOME_MSG MACHINE_NAME " valmis"
- #define MSG_SD_INSERTED "Kortti asetettu"
- #define MSG_SD_REMOVED "Kortti poistettu"
- #define MSG_MAIN "Palaa"
- #define MSG_AUTOSTART "Automaatti"
- #define MSG_DISABLE_STEPPERS "Vapauta moottorit"
- #define MSG_AUTO_HOME "Aja referenssiin"
- #define MSG_SET_ORIGIN "Aseta origo"
- #define MSG_PREHEAT_PLA "Esilammita PLA"
- #define MSG_PREHEAT_PLA_SETTINGS "Esilammita PLA konf"
- #define MSG_PREHEAT_ABS "Esilammita ABS"
- #define MSG_PREHEAT_ABS_SETTINGS "Esilammita ABS konf"
- #define MSG_COOLDOWN "Jaahdyta"
- #define MSG_EXTRUDE "Pursota"
- #define MSG_RETRACT "Veda takaisin"
- #define MSG_MOVE_AXIS "Liikuta akseleita"
- #define MSG_SPEED "Nopeus"
- #define MSG_NOZZLE "Suutin"
- #define MSG_NOZZLE1 "Suutin2"
- #define MSG_NOZZLE2 "Suutin3"
- #define MSG_BED "Alusta"
- #define MSG_FAN_SPEED "Tuul. nopeus"
- #define MSG_FLOW "Virtaus"
- #define MSG_CONTROL "Kontrolli"
- #define MSG_MIN " \002 Min"
- #define MSG_MAX " \002 Max"
- #define MSG_FACTOR " \002 Kerr"
- #define MSG_AUTOTEMP "Autotemp"
- #define MSG_ON "On "
- #define MSG_OFF "Off"
- #define MSG_PID_P "PID-P"
- #define MSG_PID_I "PID-I"
- #define MSG_PID_D "PID-D"
- #define MSG_PID_C "PID-C"
- #define MSG_ACC "Kiihtyv"
- #define MSG_VXY_JERK "Vxy-jerk"
- #define MSG_VZ_JERK "Vz-jerk"
- #define MSG_VE_JERK "Ve-jerk"
- #define MSG_VMAX "Vmax "
- #define MSG_X "x"
- #define MSG_Y "y"
- #define MSG_Z "z"
- #define MSG_E "e"
- #define MSG_VMIN "Vmin"
- #define MSG_VTRAV_MIN "VLiike min"
- #define MSG_AMAX "Amax "
- #define MSG_A_RETRACT "A-peruuta"
- #define MSG_XSTEPS "Xsteps/mm"
- #define MSG_YSTEPS "Ysteps/mm"
- #define MSG_ZSTEPS "Zsteps/mm"
- #define MSG_ESTEPS "Esteps/mm"
- #define MSG_RECTRACT "Veda takaisin"
- #define MSG_TEMPERATURE "Lampotila"
- #define MSG_MOTION "Liike"
- #define MSG_CONTRAST "LCD contrast"
- #define MSG_STORE_EPROM "Tallenna muistiin"
- #define MSG_LOAD_EPROM "Lataa muistista"
- #define MSG_RESTORE_FAILSAFE "Palauta oletus"
- #define MSG_REFRESH "Paivita"
- #define MSG_WATCH "Seuraa"
- #define MSG_PREPARE "Valmistele"
- #define MSG_TUNE "Saada"
- #define MSG_PAUSE_PRINT "Keskeyta tulostus"
- #define MSG_RESUME_PRINT "Jatka tulostusta"
- #define MSG_STOP_PRINT "Pysayta tulostus"
- #define MSG_CARD_MENU "Korttivalikko"
- #define MSG_NO_CARD "Ei korttia"
- #define MSG_DWELL "Nukkumassa..."
- #define MSG_USERWAIT "Odotetaan valintaa..."
- #define MSG_RESUMING "Jatketaan tulostusta"
- #define MSG_NO_MOVE "Ei liiketta."
- #define MSG_KILLED "KILLED. "
- #define MSG_STOPPED "STOPPED. "
- #define MSG_CONTROL_RETRACT "Veda mm"
- #define MSG_CONTROL_RETRACTF "Veda F"
- #define MSG_CONTROL_RETRACT_ZLIFT "Z mm"
- #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
- #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
- #define MSG_AUTORETRACT "AutoVeto."
- #define MSG_FILAMENTCHANGE "Change filament"
-
-// Serial Console Messages
-
- #define MSG_Enqueing "jonoon \""
- #define MSG_POWERUP "Kaynnistys"
- #define MSG_EXTERNAL_RESET " Ulkoinen Reset"
- #define MSG_BROWNOUT_RESET " Alajannite Reset"
- #define MSG_WATCHDOG_RESET " Vahtikoira Reset"
- #define MSG_SOFTWARE_RESET " Ohjelmisto Reset"
- #define MSG_MARLIN "Marlin "
- #define MSG_AUTHOR " | Author: "
- #define MSG_CONFIGURATION_VER " Paivitetty viimeksi: "
- #define MSG_FREE_MEMORY " Vapaata muistia: "
- #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
- #define MSG_OK "ok"
- #define MSG_FILE_SAVED "Tiedosto tallennettu."
- #define MSG_ERR_LINE_NO "Rivinumero ei ole Viimeisin rivi+1, Viimeisin rivi: "
- #define MSG_ERR_CHECKSUM_MISMATCH "Tarkistesummassa virhe, Viimeisin rivi: "
- #define MSG_ERR_NO_CHECKSUM "Rivilla ei tarkistesummaa, Viimeisin rivi: "
- #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Ei rivinumeroa tarkistesumman kanssa, Viimeisin rivi: "
- #define MSG_FILE_PRINTED "Tiedoston tulostus valmis"
- #define MSG_BEGIN_FILE_LIST "Tiedostolistauksen alku"
- #define MSG_END_FILE_LIST "Tiedostolistauksen loppu"
- #define MSG_M104_INVALID_EXTRUDER "M104 Virheellinen suutin "
- #define MSG_M105_INVALID_EXTRUDER "M105 Virheellinen suutin "
- #define MSG_M218_INVALID_EXTRUDER "M218 Virheellinen suutin "
- #define MSG_ERR_NO_THERMISTORS "Ei termistoreja - ei lampotiloja"
- #define MSG_M109_INVALID_EXTRUDER "M109 Virheellinen suutin "
- #define MSG_HEATING "Lammitan..."
- #define MSG_HEATING_COMPLETE "Lammitys valmis."
- #define MSG_BED_HEATING "Alusta lampiaa."
- #define MSG_BED_DONE "Alusta valmis."
- #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
- #define MSG_COUNT_X " Laskuri X: "
- #define MSG_ERR_KILLED "Tulostin pysaytetty. kill():ia kutsuttu!"
- #define MSG_ERR_STOPPED "Tulostin pysaytetty virheiden vuoksi. Korjaa virheet ja kayta M999 kaynnistaaksesi uudelleen. (Lampotila nollattiin. Aseta lampotila sen jalkeen kun jatkat.)"
- #define MSG_RESEND "Uudelleenlahetys: "
- #define MSG_UNKNOWN_COMMAND "Tuntematon komento: \""
- #define MSG_ACTIVE_EXTRUDER "Aktiivinen suutin: "
- #define MSG_INVALID_EXTRUDER "Virheellinen suutin"
- #define MSG_X_MIN "x_min: "
- #define MSG_X_MAX "x_max: "
- #define MSG_Y_MIN "y_min: "
- #define MSG_Y_MAX "y_max: "
- #define MSG_Z_MIN "z_min: "
- #define MSG_Z_MAX "z_max: "
- #define MSG_M119_REPORT "Rajakytkimien tilaraportti"
- #define MSG_ENDSTOP_HIT "AKTIIVISENA"
- #define MSG_ENDSTOP_OPEN "avoinna"
- #define MSG_HOTEND_OFFSET "Hotend offsets:"
-
- #define MSG_SD_CANT_OPEN_SUBDIR "Alihakemistoa ei voitu avata"
- #define MSG_SD_INIT_FAIL "SD alustus epaonnistui"
- #define MSG_SD_VOL_INIT_FAIL "volume.init epaonnistui"
- #define MSG_SD_OPENROOT_FAIL "openRoot epaonnistui"
- #define MSG_SD_CARD_OK "SD kortti ok"
- #define MSG_SD_WORKDIR_FAIL "workDir open epaonnistui"
- #define MSG_SD_OPEN_FILE_FAIL "avaus epaonnistui, Tiedosto: "
- #define MSG_SD_FILE_OPENED "Tiedosto avattu: "
- #define MSG_SD_SIZE " Koko: "
- #define MSG_SD_FILE_SELECTED "Tiedosto valittu"
- #define MSG_SD_WRITE_TO_FILE "Kirjoitetaan tiedostoon: "
- #define MSG_SD_PRINTING_BYTE "SD tulostus byte "
- #define MSG_SD_NOT_PRINTING "Ei SD tulostus"
- #define MSG_SD_ERR_WRITE_TO_FILE "virhe kirjoitettaessa tiedostoon"
- #define MSG_SD_CANT_ENTER_SUBDIR "Alihakemistoon ei voitu siirtya: "
-
- #define MSG_STEPPER_TOO_HIGH "Askellustaajuus liian suuri: "
- #define MSG_ENDSTOPS_HIT "paatyrajat aktivoitu: "
- #define MSG_ERR_COLD_EXTRUDE_STOP " kylmana pursotus estetty"
- #define MSG_ERR_LONG_EXTRUDE_STOP " liian pitka pursotus estetty"
-
-#endif
-#endif // ifndef LANGUAGE_H
+#ifndef LANGUAGE_H
+#define LANGUAGE_H
+
+// NOTE: IF YOU CHANGE THIS FILE / MERGE THIS FILE WITH CHANGES
+//
+// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h"
+// ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS
+
+// Languages
+// 1 English
+// 2 Polish
+// 3 French
+// 4 German
+// 5 Spanish
+// 6 Russian
+// 7 Italian
+// 8 Portuguese
+// 9 Finnish
+
+#ifndef LANGUAGE_CHOICE
+#define LANGUAGE_CHOICE 1 // Pick your language from the list above
+#endif
+
+#define PROTOCOL_VERSION "1.0"
+
+#if MOTHERBOARD == 7 || MOTHERBOARD == 71
+ #define MACHINE_NAME "Ultimaker"
+ #define FIRMWARE_URL "http://firmware.ultimaker.com"
+#elif MOTHERBOARD == 80
+ #define MACHINE_NAME "Rumba"
+ #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/"
+#elif MOTHERBOARD == 77
+ #define MACHINE_NAME "3Drag"
+ #define FIRMWARE_URL "http://3dprint.elettronicain.it/"
+#else
+ #ifdef CUSTOM_MENDEL_NAME
+ #define MACHINE_NAME CUSTOM_MENDEL_NAME
+ #else
+ #define MACHINE_NAME "Mendel"
+ #endif
+ #define FIRMWARE_URL "http://www.mendel-parts.com"
+#endif
+
+#define STRINGIFY_(n) #n
+#define STRINGIFY(n) STRINGIFY_(n)
+
+#if LANGUAGE_CHOICE == 1
+
+// LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " Ready."
+ #define MSG_SD_INSERTED "Card inserted"
+ #define MSG_SD_REMOVED "Card removed"
+ #define MSG_MAIN "Main"
+ #define MSG_AUTOSTART "Autostart"
+ #define MSG_DISABLE_STEPPERS "Disable Steppers"
+ #define MSG_AUTO_HOME "Auto Home"
+ #define MSG_SET_ORIGIN "Set Origin"
+ #define MSG_PREHEAT_PLA "Preheat PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Preheat PLA Conf"
+ #define MSG_PREHEAT_ABS "Preheat ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Preheat ABS Conf"
+ #define MSG_COOLDOWN "Cooldown"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Extrude"
+ #define MSG_RETRACT "Retract"
+ #define MSG_MOVE_AXIS "Move Axis"
+ #define MSG_SPEED "Speed"
+ #define MSG_NOZZLE "Nozzle"
+ #define MSG_NOZZLE1 "Nozzle2"
+ #define MSG_NOZZLE2 "Nozzle3"
+ #define MSG_BED "Bed"
+ #define MSG_FAN_SPEED "Fan speed"
+ #define MSG_FLOW "Flow"
+ #define MSG_CONTROL "Control"
+ #define MSG_MIN " \002 Min"
+ #define MSG_MAX " \002 Max"
+ #define MSG_FACTOR " \002 Fact"
+ #define MSG_AUTOTEMP "Autotemp"
+ #define MSG_ON "On "
+ #define MSG_OFF "Off"
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Accel"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX "Vmax "
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "VTrav min"
+ #define MSG_AMAX "Amax "
+ #define MSG_A_RETRACT "A-retract"
+ #define MSG_XSTEPS "Xsteps/mm"
+ #define MSG_YSTEPS "Ysteps/mm"
+ #define MSG_ZSTEPS "Zsteps/mm"
+ #define MSG_ESTEPS "Esteps/mm"
+ #define MSG_RECTRACT "Rectract"
+ #define MSG_TEMPERATURE "Temperature"
+ #define MSG_MOTION "Motion"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM "Store memory"
+ #define MSG_LOAD_EPROM "Load memory"
+ #define MSG_RESTORE_FAILSAFE "Restore Failsafe"
+ #define MSG_REFRESH "Refresh"
+ #define MSG_WATCH "Info screen"
+ #define MSG_PREPARE "Prepare"
+ #define MSG_TUNE "Tune"
+ #define MSG_PAUSE_PRINT "Pause Print"
+ #define MSG_RESUME_PRINT "Resume Print"
+ #define MSG_STOP_PRINT "Stop Print"
+ #define MSG_CARD_MENU "Print from SD"
+ #define MSG_NO_CARD "No Card"
+ #define MSG_DWELL "Sleep..."
+ #define MSG_USERWAIT "Wait for user..."
+ #define MSG_RESUMING "Resuming print"
+ #define MSG_NO_MOVE "No move."
+ #define MSG_KILLED "KILLED. "
+ #define MSG_STOPPED "STOPPED. "
+ #define MSG_CONTROL_RETRACT "Retract mm"
+ #define MSG_CONTROL_RETRACTF "Retract F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
+ #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
+ #define MSG_AUTORETRACT "AutoRetr."
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "enqueing \""
+ #define MSG_POWERUP "PowerUp"
+ #define MSG_EXTERNAL_RESET " External Reset"
+ #define MSG_BROWNOUT_RESET " Brown out Reset"
+ #define MSG_WATCHDOG_RESET " Watchdog Reset"
+ #define MSG_SOFTWARE_RESET " Software Reset"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Author: "
+ #define MSG_CONFIGURATION_VER " Last Updated: "
+ #define MSG_FREE_MEMORY " Free Memory: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Done saving file."
+ #define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line: "
+ #define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line: "
+ #define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line: "
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line: "
+ #define MSG_FILE_PRINTED "Done printing file"
+ #define MSG_BEGIN_FILE_LIST "Begin file list"
+ #define MSG_END_FILE_LIST "End file list"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
+ #define MSG_ERR_NO_THERMISTORS "No thermistors - no temperature"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
+ #define MSG_HEATING "Heating..."
+ #define MSG_HEATING_COMPLETE "Heating done."
+ #define MSG_BED_HEATING "Bed Heating."
+ #define MSG_BED_DONE "Bed done."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Count X: "
+ #define MSG_ERR_KILLED "Printer halted. kill() called!"
+ #define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
+ #define MSG_RESEND "Resend: "
+ #define MSG_UNKNOWN_COMMAND "Unknown command: \""
+ #define MSG_ACTIVE_EXTRUDER "Active Extruder: "
+ #define MSG_INVALID_EXTRUDER "Invalid extruder"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Reporting endstop status"
+ #define MSG_ENDSTOP_HIT "TRIGGERED"
+ #define MSG_ENDSTOP_OPEN "open"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
+ #define MSG_SD_INIT_FAIL "SD init fail"
+ #define MSG_SD_VOL_INIT_FAIL "volume.init failed"
+ #define MSG_SD_OPENROOT_FAIL "openRoot failed"
+ #define MSG_SD_CARD_OK "SD card ok"
+ #define MSG_SD_WORKDIR_FAIL "workDir open failed"
+ #define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
+ #define MSG_SD_FILE_OPENED "File opened: "
+ #define MSG_SD_SIZE " Size: "
+ #define MSG_SD_FILE_SELECTED "File selected"
+ #define MSG_SD_WRITE_TO_FILE "Writing to file: "
+ #define MSG_SD_PRINTING_BYTE "SD printing byte "
+ #define MSG_SD_NOT_PRINTING "Not SD printing"
+ #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir: "
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate too high: "
+ #define MSG_ENDSTOPS_HIT "endstops hit: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 2
+
+// LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " Gotowe."
+ #define MSG_SD_INSERTED "Karta wlozona"
+ #define MSG_SD_REMOVED "Karta usunieta"
+ #define MSG_MAIN "Main"
+ #define MSG_AUTOSTART "Autostart"
+ #define MSG_DISABLE_STEPPERS "Wylacz silniki"
+ #define MSG_AUTO_HOME "Auto. poz. zerowa"
+ #define MSG_SET_ORIGIN "Ustaw punkt zerowy"
+ #define MSG_PREHEAT_PLA "Rozgrzej PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Ustawienia roz. PLA"
+ #define MSG_PREHEAT_ABS "Rozgrzej ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Ustawienia roz. ABS"
+ #define MSG_COOLDOWN "Chlodzenie"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Ekstruzja"
+ #define MSG_RETRACT "Cofanie"
+ #define MSG_MOVE_AXIS "Ruch osi"
+ #define MSG_SPEED "Predkosc"
+ #define MSG_NOZZLE "Dysza"
+ #define MSG_NOZZLE1 "Dysza2"
+ #define MSG_NOZZLE2 "Dysza3"
+ #define MSG_BED "Loze"
+ #define MSG_FAN_SPEED "Obroty wiatraka"
+ #define MSG_FLOW "Przeplyw"
+ #define MSG_CONTROL "Kontrola"
+ #define MSG_MIN " \002 Min"
+ #define MSG_MAX " \002 Max"
+ #define MSG_FACTOR " \002 Mnoznik"
+ #define MSG_AUTOTEMP "Auto. temp."
+ #define MSG_ON "Wl. "
+ #define MSG_OFF "Wyl."
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Acc"
+ #define MSG_VXY_JERK "Zryw Vxy"
+ #define MSG_VZ_JERK "Zryw Vz"
+ #define MSG_VE_JERK "Zryw Ve"
+ #define MSG_VMAX "Vmax"
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "Vskok min"
+ #define MSG_AMAX "Amax"
+ #define MSG_A_RETRACT "A-wycofanie"
+ #define MSG_XSTEPS "krokiX/mm"
+ #define MSG_YSTEPS "krokiY/mm"
+ #define MSG_ZSTEPS "krokiZ/mm"
+ #define MSG_ESTEPS "krokiE/mm"
+ #define MSG_RECTRACT "Wycofanie"
+ #define MSG_TEMPERATURE "Temperatura"
+ #define MSG_MOTION "Ruch"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM "Zapisz w pamieci"
+ #define MSG_LOAD_EPROM "Wczytaj z pamieci"
+ #define MSG_RESTORE_FAILSAFE " Ustawienia fabryczne"
+ #define MSG_REFRESH "\004Odswiez"
+ #define MSG_WATCH "Obserwuj"
+ #define MSG_PREPARE "Przygotuj"
+ #define MSG_CONTROL "Kontroluj"
+ #define MSG_TUNE "Strojenie"
+ #define MSG_PAUSE_PRINT "Pauza"
+ #define MSG_RESUME_PRINT "Wznowienie"
+ #define MSG_STOP_PRINT "Stop"
+ #define MSG_CARD_MENU "Menu SDCard"
+ #define MSG_NO_CARD "Brak karty"
+ #define MSG_DWELL "Uspij..."
+ #define MSG_USERWAIT "Czekaj na uzytkownika..."
+ #define MSG_RESUMING "Wznawiam drukowanie"
+ #define MSG_NO_MOVE "Brak ruchu."
+ #define MSG_PART_RELEASE "Czesciowe zwolnienie"
+ #define MSG_KILLED "Ubity. "
+ #define MSG_STOPPED "Zatrzymany. "
+ #define MSG_STEPPER_RELEASED "Zwolniony."
+ #define MSG_CONTROL_RETRACT "Wycofaj mm"
+ #define MSG_CONTROL_RETRACTF "Wycofaj F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Skok Z mm:"
+ #define MSG_CONTROL_RETRACT_RECOVER "Cof. wycof. +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "Cof. wycof. F"
+ #define MSG_AUTORETRACT "Auto. wycofanie"
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "Kolejkowanie \""
+ #define MSG_POWERUP "Zasilanie wlaczone"
+ #define MSG_EXTERNAL_RESET " Reset (zewnetrzny)"
+ #define MSG_BROWNOUT_RESET " Reset (spadek napiecia)"
+ #define MSG_WATCHDOG_RESET " Reset (watchdog)"
+ #define MSG_SOFTWARE_RESET " Reset (programowy)"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Autor: "
+ #define MSG_CONFIGURATION_VER " Ostatnia aktualizacja: "
+ #define MSG_FREE_MEMORY " Wolna pamiec: "
+ #define MSG_PLANNER_BUFFER_BYTES " Bufor planisty krokow (w bajtach): "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Plik zapisany."
+ #define MSG_ERR_LINE_NO "Numer linijki nie jest ostatnim numerem linijki+1; ostatnia linijka:"
+ #define MSG_ERR_CHECKSUM_MISMATCH "Niezgodna suma kontrolna; ostatnia linijka: "
+ #define MSG_ERR_NO_CHECKSUM "Brak sumy kontrolnej w linijce; ostatnia linijka:"
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Brak numery linijki przy sumie kontrolnej; ostatnia linijka:"
+ #define MSG_FILE_PRINTED "Ukonczono wydruk z pliku"
+ #define MSG_BEGIN_FILE_LIST "Start listy plikow"
+ #define MSG_END_FILE_LIST "Koniec listy plikow"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Niepoprawny ekstruder "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Niepoprawny ekstruder "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Niepoprawny ekstruder "
+ #define MSG_ERR_NO_THERMISTORS "Brak termistorow - brak temperatury :("
+ #define MSG_M109_INVALID_EXTRUDER "M109 Niepoprawny ekstruder "
+ #define MSG_HEATING "Nagrzewanie ekstrudera..."
+ #define MSG_HEATING_COMPLETE "Nagrzewanie ekstrudera zakonczone."
+ #define MSG_BED_HEATING "Nagrzewanie loza..."
+ #define MSG_BED_DONE "Nagrzewanie loza zakonczone."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Liczenie X: "
+ #define MSG_ERR_KILLED "Drukarka zatrzymana. Wywolano kill()"
+ #define MSG_ERR_STOPPED "Drukarka zatrzymana z powodu bledu. Usun problem i zrestartuj drukartke komenda M999. (temperatura zostala zresetowana; ustaw temperature po restarcie)"
+ #define MSG_RESEND "Wyslij ponownie: "
+ #define MSG_UNKNOWN_COMMAND "Nieznane polecenie: \""
+ #define MSG_ACTIVE_EXTRUDER "Aktywny ekstruder: "
+ #define MSG_INVALID_EXTRUDER "Niepoprawny ekstruder"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Zgloszenie statusu wylacznikow krancowych"
+ #define MSG_ENDSTOP_HIT "WYZWOLONY"
+ #define MSG_ENDSTOP_OPEN "otwarty"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Nie mozna otworzyc podkatalogu"
+ #define MSG_SD_INIT_FAIL "Blad inicjalizacji karty SD"
+ #define MSG_SD_VOL_INIT_FAIL "Blad inizjalizacji wolumenu"
+ #define MSG_SD_OPENROOT_FAIL "Blad odczytywania katalogu glownego"
+ #define MSG_SD_CARD_OK "Karta SD zainicjalizowana"
+ #define MSG_SD_WORKDIR_FAIL "Blad odczytywania katalogu roboczego"
+ #define MSG_SD_OPEN_FILE_FAIL "Nie mozna otworzyc pliku: "
+ #define MSG_SD_FILE_OPENED "Otwarto plik:"
+ #define MSG_SD_SIZE " Rozmiar:"
+ #define MSG_SD_FILE_SELECTED "Wybrano plik"
+ #define MSG_SD_WRITE_TO_FILE "Zapisywanie do pliku: "
+ #define MSG_SD_PRINTING_BYTE "Drukowanie z karty SD, bajt "
+ #define MSG_SD_NOT_PRINTING "Nie trwa drukowanie z karty SD"
+ #define MSG_SD_ERR_WRITE_TO_FILE "blad podczas zapisu do pliku"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Nie mozna odczytac podkatalogu: "
+
+ #define MSG_STEPPER_TOO_HIGH "Za duza czestotliwosc krokow: "
+ #define MSG_ENDSTOPS_HIT "Wylacznik krancowy zostal wyzwolony na pozycji: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " uniemozliwiono zimna ekstruzje"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " uniemozliwiono zbyt dluga ekstruzje"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 3
+
+ #define WELCOME_MSG MACHINE_NAME " Pret."
+ #define MSG_SD_INSERTED "Carte inseree"
+ #define MSG_SD_REMOVED "Carte retiree"
+ #define MSG_MAIN " Principal \003"
+ #define MSG_AUTOSTART " Demarrage auto."
+ #define MSG_DISABLE_STEPPERS " Desactiver moteurs"
+ #define MSG_AUTO_HOME " Home auto."
+ #define MSG_SET_ORIGIN " Regler origine"
+ #define MSG_PREHEAT_PLA " Prechauffage PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS " Regl. prechauffe PLA"
+ #define MSG_PREHEAT_ABS " Prechauffage ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS " Regl. prechauffe ABS"
+ #define MSG_COOLDOWN " Refroidissement"
+ #define MSG_SWITCH_PS_ON "Allumer alimentation"
+ #define MSG_SWITCH_PS_OFF "Eteindre alimentation"
+ #define MSG_EXTRUDE " Extrusion"
+ #define MSG_RETRACT " Retractation"
+ #define MSG_PREHEAT_PLA " Prechauffage PLA"
+ #define MSG_PREHEAT_ABS " Prechauffage ABS"
+ #define MSG_MOVE_AXIS " Deplacer axe \x7E"
+ #define MSG_SPEED " Vitesse:"
+ #define MSG_NOZZLE " \002Buse:"
+ #define MSG_NOZZLE1 " \002Buse2:"
+ #define MSG_NOZZLE2 " \002Buse3:"
+ #define MSG_BED " \002Lit:"
+ #define MSG_FAN_SPEED " Vitesse ventilateur:"
+ #define MSG_FLOW " Flux:"
+ #define MSG_CONTROL " Controle \003"
+ #define MSG_MIN " \002 Min:"
+ #define MSG_MAX " \002 Max:"
+ #define MSG_FACTOR " \002 Facteur:"
+ #define MSG_AUTOTEMP " Temp. Auto.:"
+ #define MSG_ON "Marche "
+ #define MSG_OFF "Arret"
+ #define MSG_PID_P " PID-P: "
+ #define MSG_PID_I " PID-I: "
+ #define MSG_PID_D " PID-D: "
+ #define MSG_PID_C " PID-C: "
+ #define MSG_ACC " Acc:"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX " Vmax "
+ #define MSG_X "x:"
+ #define MSG_Y "y:"
+ #define MSG_Z "z:"
+ #define MSG_E "e:"
+ #define MSG_VMIN " Vmin:"
+ #define MSG_VTRAV_MIN " Vdepl min:"
+ #define MSG_AMAX " Amax "
+ #define MSG_A_RETRACT " A-retract:"
+ #define MSG_XSTEPS " Xpas/mm:"
+ #define MSG_YSTEPS " Ypas/mm:"
+ #define MSG_ZSTEPS " Zpas/mm:"
+ #define MSG_ESTEPS " Epas/mm:"
+ #define MSG_MAIN_WIDE " Principal \003"
+ #define MSG_RECTRACT "Rectracter"
+ #define MSG_TEMPERATURE "Temperature"
+ #define MSG_MOTION "Mouvement"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM " Sauvegarder memoire"
+ #define MSG_LOAD_EPROM " Lire memoire"
+ #define MSG_RESTORE_FAILSAFE " Restaurer memoire"
+ #define MSG_REFRESH "\004Actualiser"
+ #define MSG_WATCH " Surveiller \003"
+ #define MSG_PREPARE " Preparer \x7E"
+ #define MSG_PREPARE_ALT " Prepare \003"
+ #define MSG_CONTROL_ARROW " Controle \x7E"
+ #define MSG_RETRACT_ARROW " Retracter \x7E"
+ #define MSG_TUNE " Regler \x7E"
+ #define MSG_PAUSE_PRINT " Pause impression \x7E"
+ #define MSG_RESUME_PRINT " Reprendre impression \x7E"
+ #define MSG_STOP_PRINT " Arreter impression \x7E"
+ #define MSG_CARD_MENU " Menu carte \x7E"
+ #define MSG_NO_CARD " Pas de carte"
+ #define MSG_DWELL "Repos..."
+ #define MSG_USERWAIT "Attente de l'utilisateur..."
+ #define MSG_RESUMING "Reprise de l'impression"
+ #define MSG_NO_MOVE "Aucun mouvement."
+ #define MSG_PART_RELEASE "Relache partielle"
+ #define MSG_KILLED "TUE."
+ #define MSG_STOPPED "STOPPE."
+ #define MSG_STEPPER_RELEASED "RELACHE."
+ #define MSG_CONTROL_RETRACT " Retractation mm:"
+ #define MSG_CONTROL_RETRACTF " Retractation F:"
+ #define MSG_CONTROL_RETRACT_ZLIFT " Hop mm:"
+ #define MSG_CONTROL_RETRACT_RECOVER " UnRet +mm:"
+ #define MSG_CONTROL_RETRACT_RECOVERF " UnRet F:"
+ #define MSG_AUTORETRACT " Retract. Auto.:"
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. la carte SD"
+ #define MSG_CNG_SDCARD "Changer de carte SD"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "Mise en tampon \""
+ #define MSG_POWERUP "Allumage"
+ #define MSG_EXTERNAL_RESET " RAZ Externe"
+ #define MSG_BROWNOUT_RESET " RAZ defaut alim."
+ #define MSG_WATCHDOG_RESET " RAZ Watchdog"
+ #define MSG_SOFTWARE_RESET " RAZ logicielle"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Auteur: "
+ #define MSG_CONFIGURATION_VER " Derniere MaJ: "
+ #define MSG_FREE_MEMORY " Memoire libre: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Fichier enregistre."
+ #define MSG_ERR_LINE_NO "Le numero de ligne n'est pas la derniere ligne + 1, derniere ligne: "
+ #define MSG_ERR_CHECKSUM_MISMATCH "Erreur somme de controle, derniere ligne: "
+ #define MSG_ERR_NO_CHECKSUM "Pas de somme de controle avec le numero de ligne, derniere ligne: "
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Pas de numero de ligne avec somme de controle, derniere ligne: "
+ #define MSG_FILE_PRINTED "Impression terminee"
+ #define MSG_BEGIN_FILE_LIST "Debut de la liste de fichiers"
+ #define MSG_END_FILE_LIST "Fin de la liste de fichiers"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Extruder invalide"
+ #define MSG_M105_INVALID_EXTRUDER "M105 Extruder invalide"
+ #define MSG_M218_INVALID_EXTRUDER "M218 Extruder invalide"
+ #define MSG_ERR_NO_THERMISTORS "Pas de thermistor, pas de temperature"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Extruder invalide "
+ #define MSG_HEATING "En chauffe..."
+ #define MSG_HEATING_COMPLETE "Chauffe terminee."
+ #define MSG_BED_HEATING "Chauffe du lit."
+ #define MSG_BED_DONE "Chauffe du lit terminee."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Compteur X: "
+ #define MSG_ERR_KILLED "Impression arretee. kill() appelee!"
+ #define MSG_ERR_STOPPED "Impression arretee a cause d'erreurs. Corriger les erreurs et utiliser M999 pour la reprendre. (Temperature remise a zero. Reactivez la apres redemarrage)"
+ #define MSG_RESEND "Renvoie: "
+ #define MSG_UNKNOWN_COMMAND "Commande inconnue: \""
+ #define MSG_ACTIVE_EXTRUDER "Extrudeur actif: "
+ #define MSG_INVALID_EXTRUDER "Extrudeur invalide"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Affichage du status des fin de course"
+ #define MSG_ENDSTOP_HIT "DECLENCHE"
+ #define MSG_ENDSTOP_OPEN "OUVERT"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Impossible d'ouvrir le sous-repertoire"
+ #define MSG_SD_INIT_FAIL "Echec de l'initialisation de la SD"
+ #define MSG_SD_VOL_INIT_FAIL "Echec de volume.init"
+ #define MSG_SD_OPENROOT_FAIL "Echec openRoot"
+ #define MSG_SD_CARD_OK "Carte SD Ok"
+ #define MSG_SD_WORKDIR_FAIL "Echec d'ouverture workDir"
+ #define MSG_SD_OPEN_FILE_FAIL "Echec d'ouverture, Fichier: "
+ #define MSG_SD_FILE_OPENED "Fichier ouvert: "
+ #define MSG_SD_SIZE " Taille: "
+ #define MSG_SD_FILE_SELECTED "Fichier selectionne"
+ #define MSG_SD_WRITE_TO_FILE "Ecriture dans le fichier: "
+ #define MSG_SD_PRINTING_BYTE "Octet impression SD "
+ #define MSG_SD_NOT_PRINTING "Pas d'impression SD"
+ #define MSG_SD_ERR_WRITE_TO_FILE "Erreur d'ecriture dans le fichier"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Impossible d'entrer dans le sous-repertoire: "
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate trop eleve: "
+ #define MSG_ENDSTOPS_HIT "Fin de course atteint: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " Extrusion a froid evitee"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " Extrusion longue evitee"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 4
+
+// LCD Menu Messages
+
+ #define WELCOME_MSG MACHINE_NAME " Bereit."
+
+ #define MSG_SD_INSERTED "SDKarte erkannt"
+ #define MSG_SD_REMOVED "SDKarte entfernt"
+ #define MSG_MAIN "Hauptmenü"
+ #define MSG_AUTOSTART "Autostart"
+ #define MSG_DISABLE_STEPPERS "Stepper abschalten"
+ #define MSG_AUTO_HOME "Auto Nullpunkt"
+ #define MSG_SET_ORIGIN "Setze Nullpunkt"
+ #define MSG_PREHEAT_PLA "Vorwärmen PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Vorwärmen PLA Einstellungen"
+ #define MSG_PREHEAT_ABS "Vorwärmen ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Vorwärmen ABS Einstellungen"
+ #define MSG_COOLDOWN "Abkühlen"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Extrude"
+ #define MSG_RETRACT "Retract"
+ #define MSG_MOVE_AXIS "Achsen bewegen"
+ #define MSG_SPEED "Geschw"
+ #define MSG_NOZZLE "Düse"
+ #define MSG_NOZZLE1 "Düse2"
+ #define MSG_NOZZLE2 "Düse3"
+ #define MSG_BED "Bett"
+ #define MSG_FAN_SPEED "Lüftergeschw."
+ #define MSG_FLOW "Fluss"
+ #define MSG_CONTROL "Einstellungen"
+ #define MSG_MIN "\002 Min"
+ #define MSG_MAX "\002 Max"
+ #define MSG_FACTOR "\002 Faktor"
+ #define MSG_AUTOTEMP "AutoTemp"
+ #define MSG_ON "Ein"
+ #define MSG_OFF "Aus"
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Acc"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX "Vmax "
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "VTrav min"
+ #define MSG_AMAX "Amax "
+ #define MSG_A_RETRACT "A-Retract"
+ #define MSG_XSTEPS "Xsteps/mm"
+ #define MSG_YSTEPS "Ysteps/mm"
+ #define MSG_ZSTEPS "Zsteps/mm"
+ #define MSG_ESTEPS "Esteps/mm"
+ #define MSG_RECTRACT_WIDE "Rectract"
+ #define MSG_WATCH "Beobachten"
+ #define MSG_TEMPERATURE "Temperatur"
+ #define MSG_MOTION "Bewegung"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM "EPROM speichern"
+ #define MSG_LOAD_EPROM "EPROM laden"
+ #define MSG_RESTORE_FAILSAFE "Standardkonfig."
+ #define MSG_REFRESH "Aktualisieren"
+ #define MSG_PREPARE "Vorbereitung"
+ #define MSG_CONTROL "Einstellungen"
+ #define MSG_TUNE "Justierung"
+ #define MSG_PAUSE_PRINT "Druck anhalten"
+ #define MSG_RESUME_PRINT "Druck fortsetz"
+ #define MSG_STOP_PRINT "Druck stoppen"
+ #define MSG_CARD_MENU "SDKarten Menü"
+ #define MSG_NO_CARD "Keine SDKarte"
+ #define MSG_DWELL "Warten..."
+ #define MSG_USERWAIT "Warte auf Nutzer..."
+ #define MSG_RESUMING "Druck fortsetzung"
+ #define MSG_NO_MOVE "Kein Zug."
+ #define MSG_PART_RELEASE "Stepper tlw frei"
+ #define MSG_KILLED "KILLED"
+ #define MSG_STOPPED "GESTOPPT"
+ #define MSG_STEPPER_RELEASED "Stepper frei"
+ #define MSG_CONTROL_RETRACT "Retract mm"
+ #define MSG_CONTROL_RETRACTF "Retract F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
+ #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
+ #define MSG_AUTORETRACT "AutoRetr."
+ #define MSG_FILAMENTCHANGE "Filament wechseln"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "enqueing \""
+ #define MSG_POWERUP "PowerUp"
+ #define MSG_EXTERNAL_RESET " External Reset"
+ #define MSG_BROWNOUT_RESET " Brown out Reset"
+ #define MSG_WATCHDOG_RESET " Watchdog Reset"
+ #define MSG_SOFTWARE_RESET " Software Reset"
+ #define MSG_MARLIN "Marlin: "
+ #define MSG_AUTHOR " | Author: "
+ #define MSG_CONFIGURATION_VER " Last Updated: "
+ #define MSG_FREE_MEMORY " Free Memory: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Done saving file."
+ #define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
+ #define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
+ #define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
+ #define MSG_FILE_PRINTED "Done printing file"
+ #define MSG_BEGIN_FILE_LIST "Begin file list"
+ #define MSG_END_FILE_LIST "End file list"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
+ #define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
+ #define MSG_HEATING "Heating..."
+ #define MSG_HEATING_COMPLETE "Heating done."
+ #define MSG_BED_HEATING "Bed Heating."
+ #define MSG_BED_DONE "Bed done."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Count X:"
+ #define MSG_ERR_KILLED "Printer halted. kill() called !!"
+ #define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart!"
+ #define MSG_RESEND "Resend:"
+ #define MSG_UNKNOWN_COMMAND "Unknown command:\""
+ #define MSG_ACTIVE_EXTRUDER "Active Extruder: "
+ #define MSG_INVALID_EXTRUDER "Invalid extruder"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Reporting endstop status"
+ #define MSG_ENDSTOP_HIT "TRIGGERED"
+ #define MSG_ENDSTOP_OPEN "open"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
+ #define MSG_SD_INIT_FAIL "SD init fail"
+ #define MSG_SD_VOL_INIT_FAIL "volume.init failed"
+ #define MSG_SD_OPENROOT_FAIL "openRoot failed"
+ #define MSG_SD_CARD_OK "SD card ok"
+ #define MSG_SD_WORKDIR_FAIL "workDir open failed"
+ #define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
+ #define MSG_SD_FILE_OPENED "File opened:"
+ #define MSG_SD_SIZE " Size:"
+ #define MSG_SD_FILE_SELECTED "File selected"
+ #define MSG_SD_WRITE_TO_FILE "Writing to file: "
+ #define MSG_SD_PRINTING_BYTE "SD printing byte "
+ #define MSG_SD_NOT_PRINTING "Not SD printing"
+ #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate too high : "
+ #define MSG_ENDSTOPS_HIT "endstops hit: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 5
+
+// LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME "Lista."
+ #define MSG_SD_INSERTED "Tarjeta SD Colocada"
+ #define MSG_SD_REMOVED "Tarjeta SD Retirada"
+ #define MSG_MAIN "Menu Principal"
+ #define MSG_AUTOSTART " Autostart"
+ #define MSG_DISABLE_STEPPERS "Apagar Motores"
+ #define MSG_AUTO_HOME "Llevar al Origen" // "Llevar Ejes al Cero"
+ #define MSG_SET_ORIGIN "Establecer Cero"
+ #define MSG_PREHEAT_PLA "Precalentar PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Ajustar temp. PLA"
+ #define MSG_PREHEAT_ABS "Precalentar ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
+ #define MSG_COOLDOWN "Enfriar"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Extruir"
+ #define MSG_RETRACT "Retraer"
+ #define MSG_MOVE_AXIS "Mover Ejes"
+ #define MSG_SPEED "Velocidad"
+ #define MSG_NOZZLE "Nozzle"
+ #define MSG_NOZZLE1 "Nozzle2"
+ #define MSG_NOZZLE2 "Nozzle3"
+ #define MSG_BED "Base"
+ #define MSG_FAN_SPEED "Ventilador"
+ #define MSG_FLOW "Flujo"
+ #define MSG_CONTROL "Control"
+ #define MSG_MIN "\002 Min"
+ #define MSG_MAX "\002 Max"
+ #define MSG_FACTOR "\002 Fact"
+ #define MSG_AUTOTEMP "Autotemp"
+ #define MSG_ON "On"
+ #define MSG_OFF "Off"
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Acel"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX "Vmax"
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "VTrav min"
+ #define MSG_AMAX "Amax"
+ #define MSG_A_RETRACT "A-retrac."
+ #define MSG_XSTEPS "X pasos/mm"
+ #define MSG_YSTEPS "Y pasos/mm"
+ #define MSG_ZSTEPS "Z pasos/mm"
+ #define MSG_ESTEPS "E pasos/mm"
+ #define MSG_RECTRACT "Retraer"
+ #define MSG_TEMPERATURE "Temperatura"
+ #define MSG_MOTION "Movimiento"
+ #define MSG_STORE_EPROM "Guardar Memoria"
+ #define MSG_LOAD_EPROM "Cargar Memoria"
+ #define MSG_RESTORE_FAILSAFE "Rest. de emergencia"
+ #define MSG_REFRESH "Volver a cargar"
+ #define MSG_WATCH "Monitorizar"
+ #define MSG_PREPARE "Preparar"
+ #define MSG_TUNE "Ajustar"
+ #define MSG_PAUSE_PRINT "Pausar Impresion"
+ #define MSG_RESUME_PRINT "Reanudar Impresion"
+ #define MSG_STOP_PRINT "Detener Impresion"
+ #define MSG_CARD_MENU "Menu de SD"
+ #define MSG_NO_CARD "No hay Tarjeta SD"
+ #define MSG_DWELL "Reposo..."
+ #define MSG_USERWAIT "Esperando Ordenes..."
+ #define MSG_RESUMING "Resumiendo Impresion"
+ #define MSG_NO_MOVE "Sin movimiento"
+ #define MSG_KILLED "PARADA DE EMERGENCIA. "
+ #define MSG_STOPPED "PARADA."
+ #define MSG_CONTROL_RETRACT "Retraer mm"
+ #define MSG_CONTROL_RETRACTF "Retraer F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Levantar mm"
+ #define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "DesRet F"
+ #define MSG_AUTORETRACT "AutoRetr."
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Iniciando. Tarjeta-SD"
+ #define MSG_CNG_SDCARD "Cambiar Tarjeta-SD"
+ #define MSG_RECTRACT_WIDE "Retraer"
+ #define MSG_TEMPERATURE_WIDE "Temperatura"
+ #define MSG_TEMPERATURE_RTN "Temperatura"
+ #define MSG_MAIN_WIDE "Menu Principal"
+ #define MSG_MOTION_WIDE "Movimiento"
+ #define MSG_PREPARE_ALT "Preparar"
+ #define MSG_CONTROL_ARROW "Control"
+ #define MSG_RETRACT_ARROW "Retraer"
+ #define MSG_PART_RELEASE "Desacople Parcial"
+ #define MSG_STEPPER_RELEASED "Desacoplada."
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "En cola \""
+ #define MSG_POWERUP "PowerUp"
+ #define MSG_EXTERNAL_RESET " Reset Externo"
+ #define MSG_BROWNOUT_RESET " Reset por Voltaje Incorrecto"
+ #define MSG_WATCHDOG_RESET " Reset por Bloqueo"
+ #define MSG_SOFTWARE_RESET " Reset por Software"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Autor: "
+ #define MSG_CONFIGURATION_VER " Ultima actualizacion: "
+ #define MSG_FREE_MEMORY " Memoria libre: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Guardado."
+ #define MSG_ERR_LINE_NO "El Numero de Linea no es igual al Ultimo Numero de Linea+1, Ultima Linea:"
+ #define MSG_ERR_CHECKSUM_MISMATCH "el checksum no coincide, Ultima Linea:"
+ #define MSG_ERR_NO_CHECKSUM "No se pudo hallar el Checksum con el numero de linea, Ultima Linea:"
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No se hallo el Numero de Linea con el Checksum, Ultima Linea:"
+ #define MSG_FILE_PRINTED "Impresion terminada"
+ #define MSG_BEGIN_FILE_LIST "Comienzo de la lista de archivos"
+ #define MSG_END_FILE_LIST "Fin de la lista de archivos"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Extrusor Invalido "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Extrusor Invalido "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Extrusor Invalido "
+ #define MSG_ERR_NO_THERMISTORS "No hay termistores - no temp"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Extrusor Invalido "
+ #define MSG_HEATING "Calentando..."
+ #define MSG_HEATING_COMPLETE "Calentamiento Hecho."
+ #define MSG_BED_HEATING "Calentando la base."
+ #define MSG_BED_DONE "Base Caliente."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Cuenta X:"
+ #define MSG_ERR_KILLED "¡¡Impresora Parada con kill()!!"
+ #define MSG_ERR_STOPPED "¡Impresora parada por errores. Arregle el error y use M999 Para reiniciar!. (La temperatura se reestablece. Ajustela antes de continuar)"
+ #define MSG_RESEND "Reenviar:"
+ #define MSG_UNKNOWN_COMMAND "Comando Desconocido:\""
+ #define MSG_ACTIVE_EXTRUDER "Extrusor Activo: "
+ #define MSG_INVALID_EXTRUDER "Extrusor Invalido"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Comprobando fines de carrera."
+ #define MSG_ENDSTOP_HIT "PULSADO"
+ #define MSG_ENDSTOP_OPEN "abierto"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+ #define MSG_SD_CANT_OPEN_SUBDIR "No se pudo abrir la subcarpeta."
+ #define MSG_SD_INIT_FAIL "Fallo al iniciar la SD"
+ #define MSG_SD_VOL_INIT_FAIL "Fallo al montar el volumen"
+ #define MSG_SD_OPENROOT_FAIL "Fallo al abrir la carpeta raiz"
+ #define MSG_SD_CARD_OK "Tarjeta SD OK"
+ #define MSG_SD_WORKDIR_FAIL "Fallo al abrir la carpeta de trabajo"
+ #define MSG_SD_OPEN_FILE_FAIL "Error al abrir, Archivo: "
+ #define MSG_SD_FILE_OPENED "Archivo abierto:"
+ #define MSG_SD_SIZE " Tamaño:"
+ #define MSG_SD_FILE_SELECTED "Archivo Seleccionado"
+ #define MSG_SD_WRITE_TO_FILE "Escribiendo en el archivo: "
+ #define MSG_SD_PRINTING_BYTE "SD imprimiendo el byte "
+ #define MSG_SD_NOT_PRINTING "No se esta imprimiendo con SD"
+ #define MSG_SD_ERR_WRITE_TO_FILE "Error al escribir en el archivo"
+ #define MSG_SD_CANT_ENTER_SUBDIR "No se puede abrir la carpeta:"
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate demasiado alto : "
+ #define MSG_ENDSTOPS_HIT "Se ha tocado el fin de carril: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " extrusion fria evitada"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " extrusion demasiado larga evitada"
+
+#endif
+
+#if LANGUAGE_CHOICE == 6
+
+ // LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " Готов"
+ #define MSG_SD_INSERTED "Карта вставлена"
+ #define MSG_SD_REMOVED "Карта извлечена"
+ #define MSG_MAIN " Меню \003"
+ #define MSG_AUTOSTART " Автостарт "
+ #define MSG_DISABLE_STEPPERS " Выключить двигатели"
+ #define MSG_AUTO_HOME " Парковка "
+ #define MSG_SET_ORIGIN " Запомнить ноль "
+ #define MSG_PREHEAT_PLA " Преднагрев PLA "
+ #define MSG_PREHEAT_PLA_SETTINGS " Настр. преднагр.PLA"
+ #define MSG_PREHEAT_ABS " Преднагрев ABS "
+ #define MSG_PREHEAT_ABS_SETTINGS " Настр. преднагр.ABS"
+ #define MSG_COOLDOWN " Охлаждение "
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE " Экструзия "
+ #define MSG_RETRACT " Откат"
+ #define MSG_MOVE_AXIS " Движение по осям \x7E"
+ #define MSG_SPEED " Скорость:"
+ #define MSG_NOZZLE " \002 Фильера:"
+ #define MSG_NOZZLE1 " \002 Фильера2:"
+ #define MSG_NOZZLE2 " \002 Фильера3:"
+ #define MSG_BED " \002 Кровать:"
+ #define MSG_FAN_SPEED " Куллер:"
+ #define MSG_FLOW " Поток:"
+ #define MSG_CONTROL " Настройки \003"
+ #define MSG_MIN " \002 Минимум:"
+ #define MSG_MAX " \002 Максимум:"
+ #define MSG_FACTOR " \002 Фактор:"
+ #define MSG_AUTOTEMP " Autotemp:"
+ #define MSG_ON "Вкл. "
+ #define MSG_OFF "Выкл. "
+ #define MSG_PID_P " PID-P: "
+ #define MSG_PID_I " PID-I: "
+ #define MSG_PID_D " PID-D: "
+ #define MSG_PID_C " PID-C: "
+ #define MSG_ACC " Acc:"
+ #define MSG_VXY_JERK " Vxy-jerk: "
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX " Vmax "
+ #define MSG_X "x:"
+ #define MSG_Y "y:"
+ #define MSG_Z "z:"
+ #define MSG_E "e:"
+ #define MSG_VMIN " Vmin:"
+ #define MSG_VTRAV_MIN " VTrav min:"
+ #define MSG_AMAX " Amax "
+ #define MSG_A_RETRACT " A-retract:"
+ #define MSG_XSTEPS " X шаг/mm:"
+ #define MSG_YSTEPS " Y шаг/mm:"
+ #define MSG_ZSTEPS " Z шаг/mm:"
+ #define MSG_ESTEPS " E шаг/mm:"
+ #define MSG_RECTRACT " Откат подачи \x7E"
+ #define MSG_TEMPERATURE " Температура \x7E"
+ #define MSG_MOTION " Скорости \x7E"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM " Сохранить настройки"
+ #define MSG_LOAD_EPROM " Загрузить настройки"
+ #define MSG_RESTORE_FAILSAFE " Сброс настроек "
+ #define MSG_REFRESH "\004Обновить "
+ #define MSG_WATCH " Обзор \003"
+ #define MSG_PREPARE " Действия \x7E"
+ #define MSG_TUNE " Настройки \x7E"
+ #define MSG_PAUSE_PRINT " Пауза печати \x7E"
+ #define MSG_RESUME_PRINT " Продолжить печать \x7E"
+ #define MSG_STOP_PRINT " Остановить печать \x7E"
+ #define MSG_CARD_MENU " Меню карты \x7E"
+ #define MSG_NO_CARD " Нет карты"
+ #define MSG_DWELL "Сон..."
+ #define MSG_USERWAIT "Нажмите для продолж."
+ #define MSG_RESUMING "Resuming print"
+ #define MSG_NO_MOVE "Нет движения. "
+ #define MSG_PART_RELEASE " Извлечение принта "
+ #define MSG_KILLED "УБИТО. "
+ #define MSG_STOPPED "ОСТАНОВЛЕНО. "
+ #define MSG_CONTROL_RETRACT " Откат mm:"
+ #define MSG_CONTROL_RETRACTF " Откат F:"
+ #define MSG_CONTROL_RETRACT_ZLIFT " Прыжок mm:"
+ #define MSG_CONTROL_RETRACT_RECOVER " Возврат +mm:"
+ #define MSG_CONTROL_RETRACT_RECOVERF " Возврат F:"
+ #define MSG_AUTORETRACT " АвтоОткат:"
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "Запланировано \""
+ #define MSG_POWERUP "Включение питания"
+ #define MSG_EXTERNAL_RESET " Внешний сброс"
+ #define MSG_BROWNOUT_RESET " Brown out сброс"
+ #define MSG_WATCHDOG_RESET " Watchdog сброс"
+ #define MSG_SOFTWARE_RESET " программный сброс"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Автор: "
+ #define MSG_CONFIGURATION_VER " Последнее обновление: "
+ #define MSG_FREE_MEMORY " Памяти свободно: "
+ #define MSG_PLANNER_BUFFER_BYTES " Буффер очереди команд Bytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Файл записан."
+ #define MSG_ERR_LINE_NO "Номен строки это не последняя строка+1, последняя строка:"
+ #define MSG_ERR_CHECKSUM_MISMATCH "контрольная сумма не совпадает, последняя строка:"
+ #define MSG_ERR_NO_CHECKSUM "нет контрольной суммы для строки, последняя строка:"
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "нет строки для контрольной суммы, последняя строка:"
+ #define MSG_FILE_PRINTED "Печать файла завершена"
+ #define MSG_BEGIN_FILE_LIST "Список файлов"
+ #define MSG_END_FILE_LIST "Конец списка файлов"
+ #define MSG_M104_INVALID_EXTRUDER "M104 ошибка экструдера "
+ #define MSG_M105_INVALID_EXTRUDER "M105 ошибка экструдера "
+ #define MSG_M218_INVALID_EXTRUDER "M218 ошибка экструдера "
+ #define MSG_ERR_NO_THERMISTORS "Нет термистра - нет температуры"
+ #define MSG_M109_INVALID_EXTRUDER "M109 ошибка экструдера "
+ #define MSG_HEATING "Нагрев... "
+ #define MSG_HEATING_COMPLETE "Наргето. "
+ #define MSG_BED_HEATING "Нагрев стола... "
+ #define MSG_BED_DONE "Стол нагрет. "
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Count X:"
+ #define MSG_ERR_KILLED "Принтер остановлен. вызов kill() !!"
+ #define MSG_ERR_STOPPED "Ошибка принтера, останов. Устраните неисправность и используйте M999 для перезагрузки!. (Температура недоступна. Проверьте датчики)"
+ #define MSG_RESEND "Переотправка:"
+ #define MSG_UNKNOWN_COMMAND "Неизвестная команда:\""
+ #define MSG_ACTIVE_EXTRUDER "Активный экструдер: "
+ #define MSG_INVALID_EXTRUDER "Ошибка экструдера"
+ #define MSG_X_MIN "x_min:"
+ #define MSG_X_MAX "x_max:"
+ #define MSG_Y_MIN "y_min:"
+ #define MSG_Y_MAX "y_max:"
+ #define MSG_Z_MIN "z_min:"
+ #define MSG_Z_MAX "z_max:"
+ #define MSG_M119_REPORT "Статус концевиков"
+ #define MSG_ENDSTOP_HIT "Срабатывание концевика"
+ #define MSG_ENDSTOP_OPEN "Концевик освобожден"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+ #define MSG_SD_CANT_OPEN_SUBDIR "Не открыть папку"
+ #define MSG_SD_INIT_FAIL "Ошибка инициализации SD"
+ #define MSG_SD_VOL_INIT_FAIL "Ошибка инициализации раздела"
+ #define MSG_SD_OPENROOT_FAIL "Не прочесть содержимое корня"
+ #define MSG_SD_CARD_OK "SD карта в порядке"
+ #define MSG_SD_WORKDIR_FAIL "не открыть рабочую папку"
+ #define MSG_SD_OPEN_FILE_FAIL "Ошибка чтения, файл: "
+ #define MSG_SD_FILE_OPENED "Файл открыт:"
+ #define MSG_SD_SIZE " Размер:"
+ #define MSG_SD_FILE_SELECTED "Файл выбран"
+ #define MSG_SD_WRITE_TO_FILE "Запись в файл: "
+ #define MSG_SD_PRINTING_BYTE "SD печать byte "
+ #define MSG_SD_NOT_PRINTING "нет SD печати"
+ #define MSG_SD_ERR_WRITE_TO_FILE "ошибка записи в файл"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Не зайти в папку:"
+ #define MSG_STEPPER_TOO_HIGH "Частота шагов очень высока : "
+ #define MSG_ENDSTOPS_HIT "концевик сработал: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " защита холодной экструзии"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " защита превышения длинны экструзии"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 7
+
+ // LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " Pronta"
+ #define MSG_SD_INSERTED "SD Card inserita"
+ #define MSG_SD_REMOVED "SD Card rimossa"
+ #define MSG_MAIN "Menu principale"
+ #define MSG_AUTOSTART "Autostart"
+ #define MSG_DISABLE_STEPPERS "Disabilita Motori"
+ #define MSG_AUTO_HOME "Auto Home"
+ #define MSG_SET_ORIGIN "Imposta Origine"
+ #define MSG_PREHEAT_PLA "Preriscalda PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Preris. PLA Conf"
+ #define MSG_PREHEAT_ABS "Preriscalda ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Preris. ABS Conf"
+ #define MSG_COOLDOWN "Raffredda"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Estrudi"
+ #define MSG_RETRACT "Ritrai"
+ #define MSG_MOVE_AXIS "Muovi Asse"
+ #define MSG_SPEED "Velcità"
+ #define MSG_NOZZLE "Ugello"
+ #define MSG_NOZZLE1 "Ugello2"
+ #define MSG_NOZZLE2 "Ugello3"
+ #define MSG_BED "Piatto"
+ #define MSG_FAN_SPEED "Ventola"
+ #define MSG_FLOW "Flusso"
+ #define MSG_CONTROL "Controllo"
+ #define MSG_MIN " \002 Min:"
+ #define MSG_MAX " \002 Max:"
+ #define MSG_FACTOR " \002 Fact:"
+ #define MSG_AUTOTEMP "Autotemp"
+ #define MSG_ON "On "
+ #define MSG_OFF "Off"
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Accel"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX "Vmax"
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "VTrav min"
+ #define MSG_AMAX "Amax"
+ #define MSG_A_RETRACT "A-retract"
+ #define MSG_XSTEPS "Xpassi/mm"
+ #define MSG_YSTEPS "Ypassi/mm"
+ #define MSG_ZSTEPS "Zpassi/mm"
+ #define MSG_ESTEPS "Epassi/mm"
+ #define MSG_RECTRACT "Ritrai"
+ #define MSG_TEMPERATURE "Temperatura"
+ #define MSG_MOTION "Movimento"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM "Salva in EEPROM"
+ #define MSG_LOAD_EPROM "Carica da EEPROM"
+ #define MSG_RESTORE_FAILSAFE "Impostaz. default"
+ #define MSG_REFRESH "Aggiorna"
+ #define MSG_WATCH "Guarda"
+ #define MSG_PREPARE "Prepara"
+ #define MSG_TUNE "Adatta"
+ #define MSG_PAUSE_PRINT "Pausa"
+ #define MSG_RESUME_PRINT "Riprendi Stampa"
+ #define MSG_STOP_PRINT "Arresta Stampa"
+ #define MSG_CARD_MENU "SD Card Menu"
+ #define MSG_NO_CARD "No SD Card"
+ #define MSG_DWELL "Sospensione..."
+ #define MSG_USERWAIT "Attendi Utente..."
+ #define MSG_RESUMING "Riprendi Stampa"
+ #define MSG_NO_MOVE "Nessun Movimento."
+ #define MSG_KILLED "UCCISO. "
+ #define MSG_STOPPED "ARRESTATO. "
+ #define MSG_CONTROL_RETRACT "Ritrai mm"
+ #define MSG_CONTROL_RETRACTF "Ritrai F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Salta mm"
+ #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
+ #define MSG_AUTORETRACT "AutoArretramento"
+ #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Qualcosa non va in MenuStructure."
+ #define MSG_FILAMENTCHANGE "Cambia filamento"
+ #define MSG_INIT_SDCARD "Iniz. SD-Card"
+ #define MSG_CNG_SDCARD "Cambia SD-Card"
+
+ // Serial Console Messages
+
+ #define MSG_Enqueing "accodamento \""
+ #define MSG_POWERUP "Accensione"
+ #define MSG_EXTERNAL_RESET " Reset Esterno"
+ #define MSG_BROWNOUT_RESET " Brown out Reset"
+ #define MSG_WATCHDOG_RESET " Watchdog Reset"
+ #define MSG_SOFTWARE_RESET " Software Reset"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Autore: "
+ #define MSG_CONFIGURATION_VER " Ultimo Aggiornamento: "
+ #define MSG_FREE_MEMORY " Memoria Libera: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "File Salvato."
+ #define MSG_ERR_LINE_NO "Il Numero della Linea non corrisponde al Numero dell'Ultima Linea+1, Ultima Linea: "
+ #define MSG_ERR_CHECKSUM_MISMATCH "checksum non corrispondente, Ultima Linea: "
+ #define MSG_ERR_NO_CHECKSUM "Nessun Checksum con Numero di Linea, Ultima Linea: "
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Nessun Numero di Linea con Checksum, Ultima Linea: "
+ #define MSG_FILE_PRINTED "File stampato"
+ #define MSG_BEGIN_FILE_LIST "Inizio Lista File"
+ #define MSG_END_FILE_LIST "Fine Lista File"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Estrusore non valido "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Estrusore non valido "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Estrusore non valido "
+ #define MSG_ERR_NO_THERMISTORS "Nessun Termistore - nessuna temperatura"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Estrusore non valido "
+ #define MSG_HEATING "Riscaldamento..."
+ #define MSG_HEATING_COMPLETE "Stampante Calda."
+ #define MSG_BED_HEATING "Riscaldamento Piatto."
+ #define MSG_BED_DONE "Piatto Pronto."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Calcola X: "
+ #define MSG_ERR_KILLED "Stampante Calda. kill() chiamata !!"
+ #define MSG_ERR_STOPPED "Stampante fermata a causa di errori. Risolvi l'errore e usa M999 per ripartire!. (Reset temperatura. Impostala prima di ripartire)"
+ #define MSG_RESEND "Reinviato:"
+ #define MSG_UNKNOWN_COMMAND "Comando sconosciuto: \""
+ #define MSG_ACTIVE_EXTRUDER "Attiva Estrusore: "
+ #define MSG_INVALID_EXTRUDER "Estrusore non valido"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Segnalazione stato degli endstop"
+ #define MSG_ENDSTOP_HIT "INNESCATO"
+ #define MSG_ENDSTOP_OPEN "aperto"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Impossibile aprire sottocartella"
+ #define MSG_SD_INIT_FAIL "Fallita Inizializzazione SD"
+ #define MSG_SD_VOL_INIT_FAIL "Fallito il montaggio del Volume"
+ #define MSG_SD_OPENROOT_FAIL "Fallita l'apertura Cartella Principale"
+ #define MSG_SD_CARD_OK "SD card ok"
+ #define MSG_SD_WORKDIR_FAIL "Fallita l'apertura Cartella di Lavoro"
+ #define MSG_SD_OPEN_FILE_FAIL "Fallita l'apertura del File: "
+ #define MSG_SD_FILE_OPENED "File aperto: "
+ #define MSG_SD_SIZE " Dimensione: "
+ #define MSG_SD_FILE_SELECTED "File selezionato"
+ #define MSG_SD_WRITE_TO_FILE "Scrittura su file: "
+ #define MSG_SD_PRINTING_BYTE "Si sta scrivendo il byte su SD "
+ #define MSG_SD_NOT_PRINTING "Non si sta scrivendo su SD"
+ #define MSG_SD_ERR_WRITE_TO_FILE "Errore nella scrittura su file"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Impossibile entrare nella sottocartella: "
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate troppo alto: "
+ #define MSG_ENDSTOPS_HIT "Raggiunto il fondo carrello: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " prevenuta estrusione fredda"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " prevenuta estrusione troppo lunga"
+
+#endif
+
+
+#if LANGUAGE_CHOICE == 8
+
+// LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " Pronta."
+ #define MSG_SD_INSERTED "Cartao SD inserido"
+ #define MSG_SD_REMOVED "Cartao SD removido"
+ #define MSG_MAIN " Menu Principal \003"
+ #define MSG_AUTOSTART " Autostart"
+ #define MSG_DISABLE_STEPPERS " Apagar Motores"
+ #define MSG_AUTO_HOME " Ir para Origen"
+ #define MSG_SET_ORIGIN " Estabelecer Origen"
+ #define MSG_PREHEAT_PLA " pre-aquecer PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS " pre-aquecer PLA Setting"
+ #define MSG_PREHEAT_ABS " pre-aquecer ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS " pre-aquecer ABS Setting"
+ #define MSG_COOLDOWN " Esfriar"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE " Extrudar"
+ #define MSG_RETRACT " Retrair"
+ #define MSG_PREHEAT_PLA " pre-aquecer PLA"
+ #define MSG_PREHEAT_ABS " pre-aquecer ABS"
+ #define MSG_MOVE_AXIS " Mover eixo \x7E"
+ #define MSG_SPEED " Velocidade:"
+ #define MSG_NOZZLE " \002Nozzle:"
+ #define MSG_NOZZLE1 " \002Nozzle2:"
+ #define MSG_NOZZLE2 " \002Nozzle3:"
+ #define MSG_BED " \002Base:"
+ #define MSG_FAN_SPEED " Velocidade Ventoinha:"
+ #define MSG_FLOW " Fluxo:"
+ #define MSG_CONTROL " Controle \003"
+ #define MSG_MIN " \002 Min:"
+ #define MSG_MAX " \002 Max:"
+ #define MSG_FACTOR " \002 Fact:"
+ #define MSG_AUTOTEMP " Autotemp:"
+ #define MSG_ON "On "
+ #define MSG_OFF "Off"
+ #define MSG_PID_P " PID-P: "
+ #define MSG_PID_I " PID-I: "
+ #define MSG_PID_D " PID-D: "
+ #define MSG_PID_C " PID-C: "
+ #define MSG_ACC " Acc:"
+ #define MSG_VXY_JERK " Vxy-jerk: "
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX " Vmax "
+ #define MSG_X "x:"
+ #define MSG_Y "y:"
+ #define MSG_Z "z:"
+ #define MSG_E "e:"
+ #define MSG_VMIN " Vmin:"
+ #define MSG_VTRAV_MIN " VTrav min:"
+ #define MSG_AMAX " Amax "
+ #define MSG_A_RETRACT " A-retract:"
+ #define MSG_XSTEPS " Xpasso/mm:"
+ #define MSG_YSTEPS " Ypasso/mm:"
+ #define MSG_ZSTEPS " Zpasso/mm:"
+ #define MSG_ESTEPS " Epasso/mm:"
+ #define MSG_MAIN_WIDE " Menu Principal \003"
+ #define MSG_RECTRACT "Retrair"
+ #define MSG_TEMPERATURE "Temperatura"
+ #define MSG_MOTION "Movimento"
+ #define MSG_STORE_EPROM " Guardar memoria"
+ #define MSG_LOAD_EPROM " Carregar memoria"
+ #define MSG_RESTORE_FAILSAFE " Rest. de emergencia"
+ #define MSG_REFRESH "\004Recarregar"
+ #define MSG_WATCH " Monitorar \003"
+ #define MSG_PREPARE " Preparar \x7E"
+ #define MSG_PREPARE_ALT " Preparar \003"
+ #define MSG_CONTROL_ARROW " Controle \x7E"
+ #define MSG_RETRACT_ARROW " Retrair \x7E"
+ #define MSG_TUNE " Tune \x7E"
+ #define MSG_PAUSE_PRINT " Pausar Impressao \x7E"
+ #define MSG_RESUME_PRINT " Resumir Impressao \x7E"
+ #define MSG_STOP_PRINT " Parar Impressao \x7E"
+ #define MSG_CARD_MENU " Menu cartao SD \x7E"
+ #define MSG_NO_CARD " Sem cartao SD"
+ #define MSG_DWELL "Repouso..."
+ #define MSG_USERWAIT "Esperando Ordem..."
+ #define MSG_RESUMING "Resuming print"
+ #define MSG_NO_MOVE "Sem movimento."
+ #define MSG_PART_RELEASE "Lancamento Parcial"
+ #define MSG_KILLED "PARADA DE EMERGENCIA. "
+ #define MSG_STOPPED "PARADA. "
+ #define MSG_STEPPER_RELEASED "Lancado."
+ #define MSG_CONTROL_RETRACT " Retrair mm:"
+ #define MSG_CONTROL_RETRACTF " Retrair F:"
+ #define MSG_CONTROL_RETRACT_ZLIFT " Levantar mm:"
+ #define MSG_CONTROL_RETRACT_RECOVER " DesRet +mm:"
+ #define MSG_CONTROL_RETRACT_RECOVERF " DesRet F:"
+ #define MSG_AUTORETRACT " AutoRetr.:"
+ #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Algo esta errado na estrutura do Menu."
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "enqueing \""
+ #define MSG_POWERUP "PowerUp"
+ #define MSG_EXTERNAL_RESET " Reset Externo"
+ #define MSG_BROWNOUT_RESET " Reset por voltagem incorreta"
+ #define MSG_WATCHDOG_RESET " Reset por Bloqueio"
+ #define MSG_SOFTWARE_RESET " Reset por Software"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Author: "
+ #define MSG_CONFIGURATION_VER " Ultima atualizacao: "
+ #define MSG_FREE_MEMORY " memoria Livre: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Guardado."
+ #define MSG_ERR_LINE_NO "O Numero da linha Nao e igual ao ultimo Numero da linha+1, Ultima linha:"
+ #define MSG_ERR_CHECKSUM_MISMATCH "O checksum Nao coincide, Ultima linha:"
+ #define MSG_ERR_NO_CHECKSUM "Nao foi possivel encontrar o checksum com o numero da linha, Ultima linha :"
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Nao ha o numero da linha com o checksum, Ultima linha:"
+ #define MSG_FILE_PRINTED "Impressao terminada"
+ #define MSG_BEGIN_FILE_LIST "Começo da lista de arquivos"
+ #define MSG_END_FILE_LIST "Fim da lista de arquivos"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Extrusor inválido "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Extrusor inválido "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Extrusor inválido "
+ #define MSG_ERR_NO_THERMISTORS "Nao ha termistor - no temp"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Extrusor inválido "
+ #define MSG_HEATING "Aquecendo..."
+ #define MSG_HEATING_COMPLETE "Aquecido."
+ #define MSG_BED_HEATING "Aquecendo a Base."
+ #define MSG_BED_DONE "Base quente."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Conta X:"
+ #define MSG_ERR_KILLED "Impressora parada com kill() !!"
+ #define MSG_ERR_STOPPED "Impressora parada por erros. Coserte o erro e use M999 para recomeçar!. (Temperatura reiniciada. Ajuste antes de recomeçar)"
+ #define MSG_RESEND "Reenviar:"
+ #define MSG_UNKNOWN_COMMAND "Comando desconhecido:\""
+ #define MSG_ACTIVE_EXTRUDER "Extrusor ativo: "
+ #define MSG_INVALID_EXTRUDER "Extrusor invalido"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Relatando estado do ponto final"
+ #define MSG_ENDSTOP_HIT "PULSADO"
+ #define MSG_ENDSTOP_OPEN "Aberto"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Nao pode abrir sub diretorio"
+ #define MSG_SD_INIT_FAIL "Falha ao iniciar SD"
+ #define MSG_SD_VOL_INIT_FAIL "Falha ao montar volume"
+ #define MSG_SD_OPENROOT_FAIL "Falha ao abrir diretorio raiz"
+ #define MSG_SD_CARD_OK "cartao SD ok"
+ #define MSG_SD_WORKDIR_FAIL "Falha ao abrir diretorio de trabalho"
+ #define MSG_SD_OPEN_FILE_FAIL "Erro ao abrir, Arquivo: "
+ #define MSG_SD_FILE_OPENED "Arquivo aberto:"
+ #define MSG_SD_SIZE " Size:"
+ #define MSG_SD_FILE_SELECTED "Arquivo selecionado"
+ #define MSG_SD_WRITE_TO_FILE "Escrevendo no arquivo: "
+ #define MSG_SD_PRINTING_BYTE "SD imprimindo o byte "
+ #define MSG_SD_NOT_PRINTING "Nao esta se imprimindo com o SD"
+ #define MSG_SD_ERR_WRITE_TO_FILE "Erro ao escrever no arquivo"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Nao pode abrir o sub diretorio:"
+
+ #define MSG_STEPPER_TOO_HIGH "Steprate muito alto : "
+ #define MSG_ENDSTOPS_HIT "O ponto final foi tocado: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " Extrusao a frio evitada"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " Extrusao muito larga evitada"
+
+
+#endif
+
+
+
+#if LANGUAGE_CHOICE == 9
+
+// Finnish
+
+// LCD Menu Messages
+ #define WELCOME_MSG MACHINE_NAME " valmis"
+ #define MSG_SD_INSERTED "Kortti asetettu"
+ #define MSG_SD_REMOVED "Kortti poistettu"
+ #define MSG_MAIN "Palaa"
+ #define MSG_AUTOSTART "Automaatti"
+ #define MSG_DISABLE_STEPPERS "Vapauta moottorit"
+ #define MSG_AUTO_HOME "Aja referenssiin"
+ #define MSG_SET_ORIGIN "Aseta origo"
+ #define MSG_PREHEAT_PLA "Esilammita PLA"
+ #define MSG_PREHEAT_PLA_SETTINGS "Esilammita PLA konf"
+ #define MSG_PREHEAT_ABS "Esilammita ABS"
+ #define MSG_PREHEAT_ABS_SETTINGS "Esilammita ABS konf"
+ #define MSG_COOLDOWN "Jaahdyta"
+ #define MSG_SWITCH_PS_ON "Switch Power On"
+ #define MSG_SWITCH_PS_OFF "Switch Power Off"
+ #define MSG_EXTRUDE "Pursota"
+ #define MSG_RETRACT "Veda takaisin"
+ #define MSG_MOVE_AXIS "Liikuta akseleita"
+ #define MSG_SPEED "Nopeus"
+ #define MSG_NOZZLE "Suutin"
+ #define MSG_NOZZLE1 "Suutin2"
+ #define MSG_NOZZLE2 "Suutin3"
+ #define MSG_BED "Alusta"
+ #define MSG_FAN_SPEED "Tuul. nopeus"
+ #define MSG_FLOW "Virtaus"
+ #define MSG_CONTROL "Kontrolli"
+ #define MSG_MIN " \002 Min"
+ #define MSG_MAX " \002 Max"
+ #define MSG_FACTOR " \002 Kerr"
+ #define MSG_AUTOTEMP "Autotemp"
+ #define MSG_ON "On "
+ #define MSG_OFF "Off"
+ #define MSG_PID_P "PID-P"
+ #define MSG_PID_I "PID-I"
+ #define MSG_PID_D "PID-D"
+ #define MSG_PID_C "PID-C"
+ #define MSG_ACC "Kiihtyv"
+ #define MSG_VXY_JERK "Vxy-jerk"
+ #define MSG_VZ_JERK "Vz-jerk"
+ #define MSG_VE_JERK "Ve-jerk"
+ #define MSG_VMAX "Vmax "
+ #define MSG_X "x"
+ #define MSG_Y "y"
+ #define MSG_Z "z"
+ #define MSG_E "e"
+ #define MSG_VMIN "Vmin"
+ #define MSG_VTRAV_MIN "VLiike min"
+ #define MSG_AMAX "Amax "
+ #define MSG_A_RETRACT "A-peruuta"
+ #define MSG_XSTEPS "Xsteps/mm"
+ #define MSG_YSTEPS "Ysteps/mm"
+ #define MSG_ZSTEPS "Zsteps/mm"
+ #define MSG_ESTEPS "Esteps/mm"
+ #define MSG_RECTRACT "Veda takaisin"
+ #define MSG_TEMPERATURE "Lampotila"
+ #define MSG_MOTION "Liike"
+ #define MSG_CONTRAST "LCD contrast"
+ #define MSG_STORE_EPROM "Tallenna muistiin"
+ #define MSG_LOAD_EPROM "Lataa muistista"
+ #define MSG_RESTORE_FAILSAFE "Palauta oletus"
+ #define MSG_REFRESH "Paivita"
+ #define MSG_WATCH "Seuraa"
+ #define MSG_PREPARE "Valmistele"
+ #define MSG_TUNE "Saada"
+ #define MSG_PAUSE_PRINT "Keskeyta tulostus"
+ #define MSG_RESUME_PRINT "Jatka tulostusta"
+ #define MSG_STOP_PRINT "Pysayta tulostus"
+ #define MSG_CARD_MENU "Korttivalikko"
+ #define MSG_NO_CARD "Ei korttia"
+ #define MSG_DWELL "Nukkumassa..."
+ #define MSG_USERWAIT "Odotetaan valintaa..."
+ #define MSG_RESUMING "Jatketaan tulostusta"
+ #define MSG_NO_MOVE "Ei liiketta."
+ #define MSG_KILLED "KILLED. "
+ #define MSG_STOPPED "STOPPED. "
+ #define MSG_CONTROL_RETRACT "Veda mm"
+ #define MSG_CONTROL_RETRACTF "Veda F"
+ #define MSG_CONTROL_RETRACT_ZLIFT "Z mm"
+ #define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
+ #define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
+ #define MSG_AUTORETRACT "AutoVeto."
+ #define MSG_FILAMENTCHANGE "Change filament"
+ #define MSG_INIT_SDCARD "Init. SD-Card"
+ #define MSG_CNG_SDCARD "Change SD-Card"
+
+// Serial Console Messages
+
+ #define MSG_Enqueing "jonoon \""
+ #define MSG_POWERUP "Kaynnistys"
+ #define MSG_EXTERNAL_RESET " Ulkoinen Reset"
+ #define MSG_BROWNOUT_RESET " Alajannite Reset"
+ #define MSG_WATCHDOG_RESET " Vahtikoira Reset"
+ #define MSG_SOFTWARE_RESET " Ohjelmisto Reset"
+ #define MSG_MARLIN "Marlin "
+ #define MSG_AUTHOR " | Author: "
+ #define MSG_CONFIGURATION_VER " Paivitetty viimeksi: "
+ #define MSG_FREE_MEMORY " Vapaata muistia: "
+ #define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
+ #define MSG_OK "ok"
+ #define MSG_FILE_SAVED "Tiedosto tallennettu."
+ #define MSG_ERR_LINE_NO "Rivinumero ei ole Viimeisin rivi+1, Viimeisin rivi: "
+ #define MSG_ERR_CHECKSUM_MISMATCH "Tarkistesummassa virhe, Viimeisin rivi: "
+ #define MSG_ERR_NO_CHECKSUM "Rivilla ei tarkistesummaa, Viimeisin rivi: "
+ #define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Ei rivinumeroa tarkistesumman kanssa, Viimeisin rivi: "
+ #define MSG_FILE_PRINTED "Tiedoston tulostus valmis"
+ #define MSG_BEGIN_FILE_LIST "Tiedostolistauksen alku"
+ #define MSG_END_FILE_LIST "Tiedostolistauksen loppu"
+ #define MSG_M104_INVALID_EXTRUDER "M104 Virheellinen suutin "
+ #define MSG_M105_INVALID_EXTRUDER "M105 Virheellinen suutin "
+ #define MSG_M218_INVALID_EXTRUDER "M218 Virheellinen suutin "
+ #define MSG_ERR_NO_THERMISTORS "Ei termistoreja - ei lampotiloja"
+ #define MSG_M109_INVALID_EXTRUDER "M109 Virheellinen suutin "
+ #define MSG_HEATING "Lammitan..."
+ #define MSG_HEATING_COMPLETE "Lammitys valmis."
+ #define MSG_BED_HEATING "Alusta lampiaa."
+ #define MSG_BED_DONE "Alusta valmis."
+ #define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
+ #define MSG_COUNT_X " Laskuri X: "
+ #define MSG_ERR_KILLED "Tulostin pysaytetty. kill():ia kutsuttu!"
+ #define MSG_ERR_STOPPED "Tulostin pysaytetty virheiden vuoksi. Korjaa virheet ja kayta M999 kaynnistaaksesi uudelleen. (Lampotila nollattiin. Aseta lampotila sen jalkeen kun jatkat.)"
+ #define MSG_RESEND "Uudelleenlahetys: "
+ #define MSG_UNKNOWN_COMMAND "Tuntematon komento: \""
+ #define MSG_ACTIVE_EXTRUDER "Aktiivinen suutin: "
+ #define MSG_INVALID_EXTRUDER "Virheellinen suutin"
+ #define MSG_X_MIN "x_min: "
+ #define MSG_X_MAX "x_max: "
+ #define MSG_Y_MIN "y_min: "
+ #define MSG_Y_MAX "y_max: "
+ #define MSG_Z_MIN "z_min: "
+ #define MSG_Z_MAX "z_max: "
+ #define MSG_M119_REPORT "Rajakytkimien tilaraportti"
+ #define MSG_ENDSTOP_HIT "AKTIIVISENA"
+ #define MSG_ENDSTOP_OPEN "avoinna"
+ #define MSG_HOTEND_OFFSET "Hotend offsets:"
+
+ #define MSG_SD_CANT_OPEN_SUBDIR "Alihakemistoa ei voitu avata"
+ #define MSG_SD_INIT_FAIL "SD alustus epaonnistui"
+ #define MSG_SD_VOL_INIT_FAIL "volume.init epaonnistui"
+ #define MSG_SD_OPENROOT_FAIL "openRoot epaonnistui"
+ #define MSG_SD_CARD_OK "SD kortti ok"
+ #define MSG_SD_WORKDIR_FAIL "workDir open epaonnistui"
+ #define MSG_SD_OPEN_FILE_FAIL "avaus epaonnistui, Tiedosto: "
+ #define MSG_SD_FILE_OPENED "Tiedosto avattu: "
+ #define MSG_SD_SIZE " Koko: "
+ #define MSG_SD_FILE_SELECTED "Tiedosto valittu"
+ #define MSG_SD_WRITE_TO_FILE "Kirjoitetaan tiedostoon: "
+ #define MSG_SD_PRINTING_BYTE "SD tulostus byte "
+ #define MSG_SD_NOT_PRINTING "Ei SD tulostus"
+ #define MSG_SD_ERR_WRITE_TO_FILE "virhe kirjoitettaessa tiedostoon"
+ #define MSG_SD_CANT_ENTER_SUBDIR "Alihakemistoon ei voitu siirtya: "
+
+ #define MSG_STEPPER_TOO_HIGH "Askellustaajuus liian suuri: "
+ #define MSG_ENDSTOPS_HIT "paatyrajat aktivoitu: "
+ #define MSG_ERR_COLD_EXTRUDE_STOP " kylmana pursotus estetty"
+ #define MSG_ERR_LONG_EXTRUDE_STOP " liian pitka pursotus estetty"
+
+#endif
+#endif // ifndef LANGUAGE_H
diff --git a/Marlin/pins.h b/Marlin/pins.h
index 877b86024e..60235800a4 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -298,7 +298,7 @@
* Arduino Mega pin assignment
*
****************************************************************************************/
-#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
#define KNOWN_BOARD 1
//////////////////FIX THIS//////////////
@@ -314,7 +314,7 @@
// #define RAMPS_V_1_0
-#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
#define LARGE_FLASH true
@@ -392,7 +392,7 @@
#define LED_PIN 13
#endif
- #if MOTHERBOARD == 33
+ #if MOTHERBOARD == 33 || MOTHERBOARD == 35
#define FAN_PIN 9 // (Sprinter config)
#else
#define FAN_PIN 4 // IO pin. Buffer needed
@@ -401,6 +401,10 @@
#if MOTHERBOARD == 77
#define FAN_PIN 8
#endif
+
+ #if MOTHERBOARD == 35
+ #define CONTROLLERFAN_PIN 10 //Pin used for the fan to cool controller
+ #endif
#define PS_ON_PIN 12
@@ -410,12 +414,18 @@
#define KILL_PIN -1
#endif
- #define HEATER_0_PIN 10 // EXTRUDER 1
+ #if MOTHERBOARD == 35
+ #define HEATER_0_PIN 8
+ #else
+ #define HEATER_0_PIN 10 // EXTRUDER 1
+ #endif
+
#if MOTHERBOARD == 33
#define HEATER_1_PIN -1
#else
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
#endif
+
#define HEATER_2_PIN -1
#if MOTHERBOARD == 77
@@ -427,10 +437,15 @@
#define TEMP_0_PIN 13 // ANALOG NUMBERING
#define TEMP_1_PIN 15 // ANALOG NUMBERING
#define TEMP_2_PIN -1 // ANALOG NUMBERING
- #if MOTHERBOARD == 77
- #define HEATER_BED_PIN 9 // BED
+
+ #if MOTHERBOARD == 35
+ #define HEATER_BED_PIN -1 // NO BED
#else
- #define HEATER_BED_PIN 8 // BED
+ #if MOTHERBOARD == 77
+ #define HEATER_BED_PIN 9 // BED
+ #else
+ #define HEATER_BED_PIN 8 // BED
+ #endif
#endif
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
@@ -578,7 +593,7 @@
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
-#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
// SPI for Max6675 Thermocouple
@@ -592,9 +607,7 @@
#define MAX6675_SS 49
#endif
-#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
-
-
+#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
/****************************************************************************************
* Duemilanove w/ ATMega328P pin assignment
diff --git a/Marlin/stepper.cpp b/Marlin/stepper.cpp
index a7991501e9..2f1d912600 100644
--- a/Marlin/stepper.cpp
+++ b/Marlin/stepper.cpp
@@ -348,11 +348,21 @@ ISR(TIMER1_COMPA_vect)
// Set the direction bits (X_AXIS=A_AXIS and Y_AXIS=B_AXIS for COREXY)
if((out_bits & (1<<X_AXIS))!=0){
- WRITE(X_DIR_PIN, INVERT_X_DIR);
+ #ifdef DUAL_X_CARRIAGE
+ if (active_extruder != 0)
+ WRITE(X2_DIR_PIN,INVERT_X_DIR);
+ else
+ #endif
+ WRITE(X_DIR_PIN, INVERT_X_DIR);
count_direction[X_AXIS]=-1;
}
else{
- WRITE(X_DIR_PIN, !INVERT_X_DIR);
+ #ifdef DUAL_X_CARRIAGE
+ if (active_extruder != 0)
+ WRITE(X2_DIR_PIN,!INVERT_X_DIR);
+ else
+ #endif
+ WRITE(X_DIR_PIN, !INVERT_X_DIR);
count_direction[X_AXIS]=1;
}
if((out_bits & (1<<Y_AXIS))!=0){
@@ -372,29 +382,41 @@ ISR(TIMER1_COMPA_vect)
#endif
CHECK_ENDSTOPS
{
- #if defined(X_MIN_PIN) && X_MIN_PIN > -1
- bool x_min_endstop=(READ(X_MIN_PIN) != X_ENDSTOPS_INVERTING);
- if(x_min_endstop && old_x_min_endstop && (current_block->steps_x > 0)) {
- endstops_trigsteps[X_AXIS] = count_position[X_AXIS];
- endstop_x_hit=true;
- step_events_completed = current_block->step_event_count;
- }
- old_x_min_endstop = x_min_endstop;
- #endif
+ #ifdef DUAL_X_CARRIAGE
+ // with 2 x-carriages, endstops are only checked in the homing direction for the active extruder
+ if ((active_extruder == 0 && X_HOME_DIR == -1) || (active_extruder != 0 && X2_HOME_DIR == -1))
+ #endif
+ {
+ #if defined(X_MIN_PIN) && X_MIN_PIN > -1
+ bool x_min_endstop=(READ(X_MIN_PIN) != X_ENDSTOPS_INVERTING);
+ if(x_min_endstop && old_x_min_endstop && (current_block->steps_x > 0)) {
+ endstops_trigsteps[X_AXIS] = count_position[X_AXIS];
+ endstop_x_hit=true;
+ step_events_completed = current_block->step_event_count;
+ }
+ old_x_min_endstop = x_min_endstop;
+ #endif
+ }
}
}
else { // +direction
CHECK_ENDSTOPS
{
- #if defined(X_MAX_PIN) && X_MAX_PIN > -1
- bool x_max_endstop=(READ(X_MAX_PIN) != X_ENDSTOPS_INVERTING);
- if(x_max_endstop && old_x_max_endstop && (current_block->steps_x > 0)){
- endstops_trigsteps[X_AXIS] = count_position[X_AXIS];
- endstop_x_hit=true;
- step_events_completed = current_block->step_event_count;
- }
- old_x_max_endstop = x_max_endstop;
- #endif
+ #ifdef DUAL_X_CARRIAGE
+ // with 2 x-carriages, endstops are only checked in the homing direction for the active extruder
+ if ((active_extruder == 0 && X_HOME_DIR == 1) || (active_extruder != 0 && X2_HOME_DIR == 1))
+ #endif
+ {
+ #if defined(X_MAX_PIN) && X_MAX_PIN > -1
+ bool x_max_endstop=(READ(X_MAX_PIN) != X_ENDSTOPS_INVERTING);
+ if(x_max_endstop && old_x_max_endstop && (current_block->steps_x > 0)){
+ endstops_trigsteps[X_AXIS] = count_position[X_AXIS];
+ endstop_x_hit=true;
+ step_events_completed = current_block->step_event_count;
+ }
+ old_x_max_endstop = x_max_endstop;
+ #endif
+ }
}
}
@@ -507,10 +529,20 @@ ISR(TIMER1_COMPA_vect)
counter_x += current_block->steps_x;
if (counter_x > 0) {
- WRITE(X_STEP_PIN, !INVERT_X_STEP_PIN);
+ #ifdef DUAL_X_CARRIAGE
+ if (active_extruder != 0)
+ WRITE(X2_STEP_PIN,!INVERT_X_STEP_PIN);
+ else
+ #endif
+ WRITE(X_STEP_PIN, !INVERT_X_STEP_PIN);
counter_x -= current_block->step_event_count;
count_position[X_AXIS]+=count_direction[X_AXIS];
- WRITE(X_STEP_PIN, INVERT_X_STEP_PIN);
+ #ifdef DUAL_X_CARRIAGE
+ if (active_extruder != 0)
+ WRITE(X2_STEP_PIN,INVERT_X_STEP_PIN);
+ else
+ #endif
+ WRITE(X_STEP_PIN, INVERT_X_STEP_PIN);
}
counter_y += current_block->steps_y;
@@ -685,6 +717,9 @@ void st_init()
#if defined(X_DIR_PIN) && X_DIR_PIN > -1
SET_OUTPUT(X_DIR_PIN);
#endif
+ #if defined(X2_DIR_PIN) && X2_DIR_PIN > -1
+ SET_OUTPUT(X2_DIR_PIN);
+ #endif
#if defined(Y_DIR_PIN) && Y_DIR_PIN > -1
SET_OUTPUT(Y_DIR_PIN);
#endif
@@ -711,6 +746,10 @@ void st_init()
SET_OUTPUT(X_ENABLE_PIN);
if(!X_ENABLE_ON) WRITE(X_ENABLE_PIN,HIGH);
#endif
+ #if defined(X2_ENABLE_PIN) && X2_ENABLE_PIN > -1
+ SET_OUTPUT(X2_ENABLE_PIN);
+ if(!X_ENABLE_ON) WRITE(X2_ENABLE_PIN,HIGH);
+ #endif
#if defined(Y_ENABLE_PIN) && Y_ENABLE_PIN > -1
SET_OUTPUT(Y_ENABLE_PIN);
if(!Y_ENABLE_ON) WRITE(Y_ENABLE_PIN,HIGH);
@@ -788,6 +827,11 @@ void st_init()
WRITE(X_STEP_PIN,INVERT_X_STEP_PIN);
disable_x();
#endif
+ #if defined(X2_STEP_PIN) && (X2_STEP_PIN > -1)
+ SET_OUTPUT(X2_STEP_PIN);
+ WRITE(X2_STEP_PIN,INVERT_X_STEP_PIN);
+ disable_x();
+ #endif
#if defined(Y_STEP_PIN) && (Y_STEP_PIN > -1)
SET_OUTPUT(Y_STEP_PIN);
WRITE(Y_STEP_PIN,INVERT_Y_STEP_PIN);
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index ab94a5b914..f6fc82d40c 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -40,6 +40,7 @@ void copy_and_scalePID_d();
/* Different menus */
static void lcd_status_screen();
#ifdef ULTIPANEL
+extern bool powersupply;
static void lcd_main_menu();
static void lcd_tune_menu();
static void lcd_prepare_menu();
@@ -348,6 +349,14 @@ static void lcd_prepare_menu()
MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla);
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs);
MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
+#if PS_ON_PIN > -1
+ if (powersupply)
+ {
+ MENU_ITEM(gcode, MSG_SWITCH_PS_OFF, PSTR("M81"));
+ }else{
+ MENU_ITEM(gcode, MSG_SWITCH_PS_ON, PSTR("M80"));
+ }
+#endif
MENU_ITEM(submenu, MSG_MOVE_AXIS, lcd_move_menu);
END_MENU();
}
diff --git a/README.md b/README.md
index f5792ea066..014871739a 100644
--- a/README.md
+++ b/README.md
@@ -41,6 +41,8 @@ Features:
* Heater power reporting. Useful for PID monitoring.
* PID tuning
* CoreXY kinematics (www.corexy.com/theory.html)
+* Delta kinematics
+* Dual X-carriage support for multiple extruder systems
* Configurable serial port to support connection of wireless adaptors.
* Automatic operation of extruder/cold-end cooling fans based on nozzle temperature
* RC Servo Support, specify angle or duration for continuous rotation servos.