3DPrinting/MarlinFirmware-Configurations
0
0
Fork 0
mirror of https://github.com/MarlinFirmware/Configurations.git synced 2025-09-17 01:27:55 +00:00
Code Issues Releases Wiki Activity

Examples Customizations

Browse source
This commit is contained in:
GitHub Actions 2025-09-14 04:13:03 +00:00
parent cffd397f39
commit 68cf772c7c
768 changed files with 48121 additions and 36228 deletions
Download patch file Download diff file Expand all files Collapse all files

61
config/examples/UltiMachine/Archim1/Configuration_adv.h
View file

@ -21,6 +21,8 @@
*/
#pragma once
#define CONFIG_EXAMPLES_DIR "UltiMachine/Archim1"
/**
* Configuration_adv.h
*
@ -1079,7 +1081,7 @@
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
#define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
#define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
@ -1150,18 +1152,16 @@
#if ENABLED(FT_MOTION)
//#define FTM_IS_DEFAULT_MOTION // Use FT Motion as the factory default?
#define FTM_DEFAULT_DYNFREQ_MODE dynFreqMode_DISABLED // Default mode of dynamic frequency calculation. (DISABLED, Z_BASED, MASS_BASED)
#define FTM_DEFAULT_SHAPER_X ftMotionShaper_NONE // Default shaper mode on X axis (NONE, ZV, ZVD, ZVDD, ZVDDD, EI, 2HEI, 3HEI, MZV)
#define FTM_DEFAULT_SHAPER_Y ftMotionShaper_NONE // Default shaper mode on Y axis
#define FTM_SHAPING_DEFAULT_FREQ_X 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_SHAPING_DEFAULT_FREQ_Y 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_LINEAR_ADV_DEFAULT_ENA false // Default linear advance enable (true) or disable (false)
#define FTM_LINEAR_ADV_DEFAULT_K 0.0f // Default linear advance gain. (Acceleration-based scaling factor.)
#define FTM_DEFAULT_SHAPER_X ftMotionShaper_NONE // Default shaper mode on X axis (NONE, ZV, ZVD, ZVDD, ZVDDD, EI, 2HEI, 3HEI, MZV)
#define FTM_SHAPING_DEFAULT_FREQ_X 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_SHAPING_ZETA_X 0.1f // Zeta used by input shapers for X axis
#define FTM_SHAPING_V_TOL_X 0.05f // Vibration tolerance used by EI input shapers for X axis
#define FTM_DEFAULT_SHAPER_Y ftMotionShaper_NONE // Default shaper mode on Y axis
#define FTM_SHAPING_DEFAULT_FREQ_Y 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_SHAPING_ZETA_Y 0.1f // Zeta used by input shapers for Y axis
#define FTM_SHAPING_V_TOL_X 0.05f // Vibration tolerance used by EI input shapers for X axis
#define FTM_SHAPING_V_TOL_Y 0.05f // Vibration tolerance used by EI input shapers for Y axis
//#define FT_MOTION_MENU // Provide a MarlinUI menu to set M493 parameters
@ -1424,15 +1424,15 @@
* Custom Microstepping
* Override as-needed for your setup. Up to 3 MS pins are supported.
*/
//#define MICROSTEP1 LOW,LOW,LOW
//#define MICROSTEP2 HIGH,LOW,LOW
//#define MICROSTEP4 LOW,HIGH,LOW
//#define MICROSTEP8 HIGH,HIGH,LOW
//#define MICROSTEP16 LOW,LOW,HIGH
//#define MICROSTEP32 HIGH,LOW,HIGH
#define MICROSTEP1 LOW,LOW,LOW
#define MICROSTEP2 HIGH,LOW,LOW
#define MICROSTEP4 LOW,HIGH,LOW
#define MICROSTEP8 HIGH,HIGH,LOW
#define MICROSTEP16 LOW,LOW,HIGH
#define MICROSTEP32 HIGH,LOW,HIGH
// Microstep settings (Requires a board with pins named X_MS1, X_MS2, etc.)
#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
#define MICROSTEP_MODES { 32, 32, 32, 32, 32, 32 } // [1,2,4,8,16]
/**
* @section stepper motor current
@ -1454,7 +1454,7 @@
* M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
* M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
*/
//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
#define PWM_MOTOR_CURRENT { 1200, 1200, 1200 } // Values in milliamps
//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
@ -1743,7 +1743,7 @@
*
* :['SPI_HALF_SPEED', 'SPI_QUARTER_SPEED', 'SPI_EIGHTH_SPEED']
*/
//#define SD_SPI_SPEED SPI_HALF_SPEED
#define SD_SPI_SPEED SPI_HALF_SPEED
// The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
// Enable this option and set to HIGH if your SD cards are incorrectly detected.
@ -2339,8 +2339,12 @@
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
//#define BABYSTEP_GLOBAL_Z // Combine M424 Z and Babystepping
#if ANY(BABYSTEP_ZPROBE_OFFSET, BABYSTEP_GLOBAL_Z)
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
#endif
//#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
#endif
#endif
@ -3932,6 +3936,14 @@
*/
//#define CNC_COORDINATE_SYSTEMS
/**
* CNC Drilling Cycle - UNDER DEVELOPMENT
*
* Enables G81 to perform a drilling cycle.
* Currently only supports a single cycle, no G-code chaining.
*/
//#define CNC_DRILLING_CYCLE
// @section security
/**
@ -4028,6 +4040,15 @@
//#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
#endif
/**
* Variables
*
* Define a variable from 100-115 with G-code like '#101=19.6'.
* A variable can then be used in a G-code expression like 'G0 X[#101+3]'.
* See https://gcodetutor.com/cnc-macro-programming/cnc-variables.html
*/
//#define GCODE_VARIABLES
/**
* Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
*/