mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2025-09-16 17:17:54 +00:00
Merge branch 'import-2.1.x' into pr/1141
This commit is contained in:
Scott Lahteine
commit
a264f161b4
764 changed files with 9160 additions and 794 deletions
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -906,7 +906,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2289,7 +2289,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -1984,7 +1984,6 @@
|
|||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_PIN 24
|
||||
|
||||
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
|
|
@ -2288,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -1984,7 +1984,6 @@
|
|||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_PIN 24
|
||||
|
||||
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
|
|
@ -2288,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -973,7 +973,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2366,7 +2366,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2278,6 +2278,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2364,6 +2366,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3696,6 +3716,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -974,7 +974,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2367,7 +2367,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2269,6 +2269,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2355,6 +2357,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3687,6 +3707,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -905,7 +905,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2288,7 +2288,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3688,6 +3708,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -905,7 +905,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2363,7 +2363,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 5
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -2290,7 +2290,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -2289,7 +2289,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -906,7 +906,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2289,7 +2289,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -906,7 +906,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2289,7 +2289,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -910,7 +910,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2293,7 +2293,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -910,7 +910,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2293,7 +2293,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -910,7 +910,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2293,7 +2293,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -910,7 +910,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2293,7 +2293,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -908,7 +908,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2291,7 +2291,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -905,7 +905,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2288,7 +2288,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -905,7 +905,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2288,7 +2288,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 0 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 7 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 7
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -943,7 +943,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2347,7 +2347,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 5
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -911,7 +911,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2303,7 +2303,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -905,7 +905,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2288,7 +2288,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2273,6 +2273,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2359,6 +2361,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3691,6 +3711,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -919,7 +919,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2303,7 +2303,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2288,7 +2288,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -904,7 +904,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2287,7 +2287,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2265,6 +2265,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2351,6 +2353,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3683,6 +3703,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -902,7 +902,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2285,7 +2285,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -902,7 +902,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2285,7 +2285,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2268,6 +2268,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2354,6 +2356,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3686,6 +3706,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -911,7 +911,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2301,7 +2301,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2270,6 +2270,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2356,6 +2358,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3688,6 +3708,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -924,7 +924,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2309,7 +2309,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2270,6 +2270,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2356,6 +2358,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3688,6 +3708,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -907,7 +907,7 @@
|
|||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
|
|
@ -2290,7 +2290,7 @@
|
|||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
|
|
|||
|
|
@ -2269,6 +2269,8 @@
|
|||
#define ADC_BUTTON_DEBOUNCE_DELAY 16 // (count) Increase if buttons bounce or repeat too fast
|
||||
#endif
|
||||
|
||||
//#define FAST_BUTTON_POLLING // Poll buttons at ~1kHz on 8-bit AVR. Set to 'false' for slow polling on 32-bit.
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
|
|
@ -2355,6 +2357,24 @@
|
|||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
|
||||
//#define SMOOTH_LIN_ADVANCE // Remove limits on acceleration by gradual increase of nozzle pressure
|
||||
#if ENABLED(SMOOTH_LIN_ADVANCE)
|
||||
/**
|
||||
* ADVANCE_TAU is also the time ahead that the smoother needs to look
|
||||
* into the planner, so the planner needs to have enough blocks loaded.
|
||||
* For k=0.04 at 10k acceleration and an "Orbiter 2" extruder it can be as low as 0.0075.
|
||||
* Adjust by lowering the value until you observe the extruder skipping, then raise slightly.
|
||||
* Higher k and higher XY acceleration may require larger ADVANCE_TAU to avoid skipping steps.
|
||||
*/
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_TAU { 0.01 } // (s) Smoothing time to reduce extruder acceleration, per extruder
|
||||
#else
|
||||
#define ADVANCE_TAU 0.01 // (s) Smoothing time to reduce extruder acceleration
|
||||
#endif
|
||||
#define SMOOTH_LIN_ADV_HZ 5000 // (Hz) How often to update extruder speed
|
||||
#define INPUT_SHAPING_E_SYNC // Synchronize the extruder-shaped XY axes (to increase precision)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -3687,6 +3707,8 @@
|
|||
#define SPEED_POWER_MIN 5000 // (RPM)
|
||||
#define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
|
||||
#define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
|
||||
|
||||
//#define DEFAULT_ACCELERATION_SPINDLE 1000 // (°/s/s) Default spindle acceleration (speed change with time)
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
|
|
|||
Some files were not shown because too many files have changed in this diff Show more
Loading…
Add table
Add a link
Reference in a new issue