1
0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-12-14 06:21:44 +00:00
MarlinFirmware/Marlin/src/pins/pins_RAMPS_SMART.h

114 lines
3.7 KiB
C
Raw Normal View History

2017-07-18 23:29:06 +00:00
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Arduino Due with RAMPS-SMART pin assignments
*
* Applies to the following boards:
*
* RAMPS_SMART_EFB (Hotend, Fan, Bed)
* RAMPS_SMART_EEB (Hotend0, Hotend1, Bed)
* RAMPS_SMART_EFF (Hotend, Fan0, Fan1)
* RAMPS_SMART_EEF (Hotend0, Hotend1, Fan)
* RAMPS_SMART_SF (Spindle, Controller Fan)
*
* Differences between
* RAMPS_14 | RAMPS-SMART
* NONE | D16 (Additional AUX-3 pin(AUX3_2PIN), shares the same pin with AUX4_18PIN)
* NONE | D17 (Additional AUX-3 pin(AUX3_1PIN), shares the same pin with AUX4_17PIN)
* D0 | NONE
* D1 | NONE
* A3/D57 | NONE
* A4/D58 | NONE
* A5/D59 | A3/D57
* A9/D63 | A4/D58
* A10/D64 | A5/D59
* A11/D65 | D66
* A12/D66 | D67
* A13 | A9
* A14 | A10
* A15 | A11
*
*
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER works fine connected to AUX-4 with
* Smart Adapter, but requires removing the AUX3 pin header on the adapter to fit.
* To use the SD card reader, wire its pins to AUX-3 (and use Software SPI).
*
* To use Hardware SPI for SD, the SDSS pin must be set to 52 instead of 53.
* Hardware SPI also requires additional wiring because the board doesn't pass
* the 6-pin SPI header from the DUE board.
* (Search the web for "Arduino DUE Board Pinout" to see the correct header.)
2017-07-18 23:29:06 +00:00
*/
#ifndef __SAM3X8E__
#error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
2017-07-18 23:29:06 +00:00
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "RAMPS-SMART"
#endif
#define IS_RAMPS_SMART
#include "pins_RAMPS.h"
// I2C EEPROM with 4K of space
#define I2C_EEPROM
#define E2END 0xFFF
2018-04-10 08:34:20 +00:00
#define RESET_PIN 42 // Resets the board if the jumper is attached
2017-07-18 23:29:06 +00:00
//
// Temperature Sensors
//
#undef TEMP_0_PIN
#define TEMP_0_PIN 9 // Analog Input
#undef TEMP_1_PIN
#define TEMP_1_PIN 10 // Analog Input
#undef TEMP_BED_PIN
#define TEMP_BED_PIN 11 // Analog Input
// SPI for Max6675 or Max31855 Thermocouple
#if DISABLED(SDSUPPORT)
#undef MAX6675_SS
2018-03-28 17:51:59 +00:00
#define MAX6675_SS 67 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
2017-07-18 23:29:06 +00:00
#else
#undef MAX6675_SS
2018-03-28 17:51:59 +00:00
#define MAX6675_SS 67 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
2017-07-18 23:29:06 +00:00
#endif
//
// LCD / Controller
//
// Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel
#if ENABLED(AZSMZ_12864)
2018-03-28 17:51:59 +00:00
#define BEEPER_PIN 66 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65
2017-07-18 23:29:06 +00:00
#define DOGLCD_A0 59
#define DOGLCD_CS 44
#define BTN_EN1 58
#define BTN_EN2 40
2018-03-28 17:51:59 +00:00
#define BTN_ENC 67 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66
#define SD_DETECT_PIN 49 // Pin 49 for display sd interface, 72 for easy adapter board
2017-07-18 23:29:06 +00:00
#define KILL_PIN 42
#endif