1
0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-12-13 22:11:38 +00:00
MarlinFirmware/Marlin/src/pins/pins_MKS_SBASE.h

204 lines
5.5 KiB
C
Raw Normal View History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* MKS SBASE pin assignments
*/
#ifndef TARGET_LPC1768
#error "Oops! Make sure you have LPC1768 selected."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "MKS SBASE"
#define DEFAULT_WEBSITE_URL "https://github.com/makerbase-mks/MKS-SBASE"
#endif
// unused
/*
#define PIN_P0_27 P0_27
#define PIN_P0_28 P0_28
*/
//
// Limit Switches
//
#define X_MIN_PIN P1_24 //10k pullup to 3.3V, 1K series
#define X_MAX_PIN P1_25 //10k pullup to 3.3V, 1K series
#define Y_MIN_PIN P1_26 //10k pullup to 3.3V, 1K series
#define Y_MAX_PIN P1_27 //10k pullup to 3.3V, 1K series
#define Z_MIN_PIN P1_28 //The original Mks Sbase DIO19 has a 10k pullup to 3.3V or 5V, 1K series, so when using a Zprobe we must use DIO41 (J8 P1.22)
#define Z_MAX_PIN P1_29 //10k pullup to 3.3V, 1K series
//
// Steppers
//
#define X_STEP_PIN P2_0
#define X_DIR_PIN P0_5
#define X_ENABLE_PIN P0_4
#define Y_STEP_PIN P2_1
#define Y_DIR_PIN P0_11
#define Y_ENABLE_PIN P0_10
#define Z_STEP_PIN P2_2
#define Z_DIR_PIN P0_20
#define Z_ENABLE_PIN P0_19
#define E0_STEP_PIN P2_3
#define E0_DIR_PIN P0_22
#define E0_ENABLE_PIN P0_21
#define E1_STEP_PIN P2_8
#define E1_DIR_PIN P2_13
#define E1_ENABLE_PIN P4_29
//
// Temperature Sensors
// 3.3V max when defined as an analog input
//
#define TEMP_BED_PIN 0 // A0 (TH1)
#define TEMP_0_PIN 1 // A1 (TH2)
#define TEMP_1_PIN 2 // A2 (TH3)
#define TEMP_2_PIN 3 // A3 (TH4)
//
// Heaters / Fans
//
#define HEATER_BED_PIN P2_5
#define HEATER_0_PIN P2_7
#define HEATER_1_PIN P2_6
#define FAN_PIN P2_4
#define PS_ON_PIN P0_25
//
// Connector J7
//
// 5V
// NC
// GND
#define PIN_P0_17 P0_17
#define PIN_P0_16 P0_16
#define PIN_P0_14 P0_14
//
// Connector J8
//
// GND
#define PIN_P1_22 P1_22
#define PIN_P1_23 P1_23
#define PIN_P2_12 P2_12
#define PIN_P2_11 P2_11
#define PIN_P4_28 P4_28
//
// Prusa i3 MK2 Multi Material Multiplexer Support
//
#if ENABLED(MK2_MULTIPLEXER)
#define E_MUX0_PIN P1_23 // J8-3
#define E_MUX1_PIN P2_12 // J8-4
#define E_MUX2_PIN P2_11 // J8-5
#endif
/**
* Smart LCD adapter
*
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
* is needed to pick up 5V for the EXP1 connection.
*
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
* on the LCD display during accesses of the SD card. The menus/code has been arranged so
* that the garbage/lines are erased immediately after the SD card accesses are completed.
*/
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_31 // EXP1.1
#define BTN_ENC P1_30 // EXP1.2
#define BTN_EN1 P3_26 // EXP2.5
#define BTN_EN2 P3_25 // EXP2.3
#define SD_DETECT_PIN P0_27 // EXP2.7
#define LCD_PINS_RS P0_16 // EXP1.4
#define LCD_SDSS P0_28 // EXP2.4
#define LCD_PINS_ENABLE P0_18 // EXP1.3
#define LCD_PINS_D4 P0_15 // EXP1.5
#endif // ULTRA_LCD
//
// Ethernet pins
//
#ifndef ULTIPANEL
#define ENET_MDIO P1_17 // J12-4
#define ENET_RX_ER P1_14 // J12-6
#define ENET_RXD1 P1_10 // J12-8
#endif
#define ENET_MOC P1_16 // J12-3
#define REF_CLK P1_15 // J12-5
#define ENET_RXD0 P1_9 // J12-7
#define ENET_CRS P1_8 // J12-9
#define ENET_TX_EN P1_4 // J12-10
#define ENET_TXD0 P1_0 // J12-11
#define ENET_TXD1 P1_1 // J12-12
/**
* PWMs
*
* There are 6 PWMs. Each PWM can be assigned to one of two pins.
*
* SERVO2 does NOT have a PWM assigned to it.
*
* PWM1.1 P1_18 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM
* PWM1.1 P2_0 E0_STEP_PIN
* PWM1.2 P1_20 SERVO0_PIN
* PWM1.2 P2_1 X_STEP_PIN
* PWM1.3 P1_21 SERVO1_PIN J5-1
* PWM1.3 P2_2 Y_STEP_PIN
* PWM1.4 P1_23 SDSS(SSEL0) J3-5 AUX-3
* PWM1.4 P2_3 Z_STEP_PIN
* PWM1.5 P1_24 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.5 P2_4 RAMPS_D9_PIN
* PWM1.6 P1_26 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.6 P2_5 RAMPS_D10_PIN
*/
/**
* Special pins
* P1_30 - not 5V tolerant
* P1_31 - not 5V tolerant
* P0_27 - open collector
* P0_28 - open collector
*
*/