mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-12-01 23:58:33 +00:00
94 lines
2.2 KiB
C
94 lines
2.2 KiB
C
|
/**
|
||
|
|
* Marlin 3D Printer Firmware
|
||
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
*
|
||
|
|
* Based on Sprinter and grbl.
|
||
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
|
*
|
||
|
|
* This program is free software: you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License as published by
|
||
|
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
|
* (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
#if ENABLED(EXT_SOLENOID)
|
||
|
|
|
||
|
|
void enable_solenoid(const uint8_t num) {
|
||
|
|
switch (num) {
|
||
|
|
case 0:
|
||
|
|
OUT_WRITE(SOL0_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
#if HAS_SOLENOID_1 && EXTRUDERS > 1
|
||
|
|
case 1:
|
||
|
|
OUT_WRITE(SOL1_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_2 && EXTRUDERS > 2
|
||
|
|
case 2:
|
||
|
|
OUT_WRITE(SOL2_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_3 && EXTRUDERS > 3
|
||
|
|
case 3:
|
||
|
|
OUT_WRITE(SOL3_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_4 && EXTRUDERS > 4
|
||
|
|
case 4:
|
||
|
|
OUT_WRITE(SOL4_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
#endif
|
||
|
|
default:
|
||
|
|
SERIAL_ECHO_START();
|
||
|
|
SERIAL_ECHOLNPGM(MSG_INVALID_SOLENOID);
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void enable_solenoid_on_active_extruder() { enable_solenoid(active_extruder); }
|
||
|
|
|
||
|
|
void disable_all_solenoids() {
|
||
|
|
OUT_WRITE(SOL0_PIN, LOW);
|
||
|
|
#if HAS_SOLENOID_1 && EXTRUDERS > 1
|
||
|
|
OUT_WRITE(SOL1_PIN, LOW);
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_2 && EXTRUDERS > 2
|
||
|
|
OUT_WRITE(SOL2_PIN, LOW);
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_3 && EXTRUDERS > 3
|
||
|
|
OUT_WRITE(SOL3_PIN, LOW);
|
||
|
|
#endif
|
||
|
|
#if HAS_SOLENOID_4 && EXTRUDERS > 4
|
||
|
|
OUT_WRITE(SOL4_PIN, LOW);
|
||
|
|
#endif
|
||
|
|
}
|
||
|
|
|
||
|
|
/**
|
||
|
|
* M380: Enable solenoid on the active extruder
|
||
|
|
*/
|
||
|
|
void gcode_M380() {
|
||
|
|
|
||
|
|
enable_solenoid_on_active_extruder();
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
/**
|
||
|
|
* M381: Disable all solenoids
|
||
|
|
*/
|
||
|
|
void gcode_M381() {
|
||
|
|
|
||
|
|
disable_all_solenoids();
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
#endif // EXT_SOLENOID
|