mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2025-01-22 17:52:57 +00:00
🚸 Thermistor updates
This commit is contained in:
Scott Lahteine
parent
20ee8dde8c
commit
244c257461
4 changed files with 336 additions and 209 deletions
|
|
@ -443,78 +443,70 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
* 2 : 200kΩ ATC Semitec 204GT-2
|
||||
* 202 : 200kΩ Copymaster 3D
|
||||
* 3 : ???Ω Mendel-parts thermistor
|
||||
* 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
|
||||
* 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
|
||||
* 501 : 100kΩ Zonestar - Tronxy X3A
|
||||
* 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
|
||||
* 503 : 100kΩ Zonestar (Z8XM2) Heated Bed thermistor
|
||||
* 504 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-B3950) Hotend Thermistor
|
||||
* 505 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-3950) Bed Thermistor
|
||||
* 512 : 100kΩ RPW-Ultra hotend
|
||||
* 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
|
||||
* 7 : 100kΩ Honeywell 135-104LAG-J01
|
||||
* 71 : 100kΩ Honeywell 135-104LAF-J01
|
||||
* 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
|
||||
* 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
|
||||
* 10 : 100kΩ RS PRO 198-961
|
||||
* 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
|
||||
* 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
|
||||
* 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
|
||||
* 15 : 100kΩ Calibrated for JGAurora A5 hotend
|
||||
* 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
|
||||
* 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
|
||||
* 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
|
||||
* 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
|
||||
* 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
|
||||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
* 2 : 200kΩ ATC Semitec 204GT-2
|
||||
* 202 : 200kΩ Copymaster 3D
|
||||
* 3 : ???Ω Mendel-parts thermistor
|
||||
* 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
|
||||
* 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
|
||||
* 501 : 100kΩ Zonestar - Tronxy X3A
|
||||
* 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
|
||||
* 503 : 100kΩ Zonestar (Z8XM2) Heated Bed thermistor
|
||||
* 504 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-B3950) Hotend Thermistor
|
||||
* 505 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-3950) Bed Thermistor
|
||||
* 512 : 100kΩ RPW-Ultra hotend
|
||||
* 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
|
||||
* 7 : 100kΩ Honeywell 135-104LAG-J01
|
||||
* 71 : 100kΩ Honeywell 135-104LAF-J01
|
||||
* 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
|
||||
* 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
|
||||
* 10 : 100kΩ RS PRO 198-961
|
||||
* 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
|
||||
* 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
|
||||
* 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
|
||||
* 14 : 100kΩ (R25), 4092K (beta25), 4.7kΩ pull-up, bed thermistor as used in Ender-5 S1
|
||||
* 15 : 100kΩ Calibrated for JGAurora A5 hotend
|
||||
* 17 : 100kΩ Dagoma NTC white thermistor
|
||||
* 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
|
||||
* 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
|
||||
* 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
|
||||
* 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
|
||||
* 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
|
||||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 666 : 200kΩ Einstart S custom thermistor with 10k pullup.
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -526,15 +518,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-2 and bed)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-2 and bed)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-2 and bed)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
|
|||
|
|
@ -23,6 +23,10 @@
|
|||
|
||||
// R25 = 100 kOhm, beta25 = 4092 K, 4.7 kOhm pull-up, bed thermistor
|
||||
constexpr temp_entry_t temptable_1[] PROGMEM = {
|
||||
{ OV( 18), 320 },
|
||||
{ OV( 19), 315 },
|
||||
{ OV( 20), 310 },
|
||||
{ OV( 22), 305 },
|
||||
{ OV( 23), 300 },
|
||||
{ OV( 25), 295 },
|
||||
{ OV( 27), 290 },
|
||||
|
|
|
|||
85
Marlin/src/module/thermistor/thermistor_14.h
Normal file
85
Marlin/src/module/thermistor/thermistor_14.h
Normal file
|
|
@ -0,0 +1,85 @@
|
|||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
// R25 = 100 kOhm, beta25 = 4092 K, 4.7 kOhm pull-up, bed thermistor
|
||||
constexpr temp_entry_t temptable_14[] PROGMEM = {
|
||||
{ OV( 23), 275 },
|
||||
{ OV( 25), 270 },
|
||||
{ OV( 27), 265 },
|
||||
{ OV( 28), 260 },
|
||||
{ OV( 31), 255 },
|
||||
{ OV( 33), 250 },
|
||||
{ OV( 35), 245 },
|
||||
{ OV( 38), 240 },
|
||||
{ OV( 41), 235 },
|
||||
{ OV( 44), 230 },
|
||||
{ OV( 47), 225 },
|
||||
{ OV( 52), 220 },
|
||||
{ OV( 56), 215 },
|
||||
{ OV( 62), 210 },
|
||||
{ OV( 68), 205 },
|
||||
{ OV( 74), 200 },
|
||||
{ OV( 81), 195 },
|
||||
{ OV( 90), 190 },
|
||||
{ OV( 99), 185 },
|
||||
{ OV( 108), 180 },
|
||||
{ OV( 121), 175 },
|
||||
{ OV( 133), 170 },
|
||||
{ OV( 147), 165 },
|
||||
{ OV( 162), 160 },
|
||||
{ OV( 180), 155 },
|
||||
{ OV( 199), 150 },
|
||||
{ OV( 219), 145 },
|
||||
{ OV( 243), 140 },
|
||||
{ OV( 268), 135 },
|
||||
{ OV( 296), 130 },
|
||||
{ OV( 326), 125 },
|
||||
{ OV( 358), 120 },
|
||||
{ OV( 398), 115 },
|
||||
{ OV( 435), 110 },
|
||||
{ OV( 476), 105 },
|
||||
{ OV( 519), 100 },
|
||||
{ OV( 566), 95 },
|
||||
{ OV( 610), 90 },
|
||||
{ OV( 658), 85 },
|
||||
{ OV( 703), 80 },
|
||||
{ OV( 742), 75 },
|
||||
{ OV( 773), 70 },
|
||||
{ OV( 807), 65 },
|
||||
{ OV( 841), 60 },
|
||||
{ OV( 871), 55 },
|
||||
{ OV( 895), 50 },
|
||||
{ OV( 918), 45 },
|
||||
{ OV( 937), 40 },
|
||||
{ OV( 954), 35 },
|
||||
{ OV( 968), 30 },
|
||||
{ OV( 978), 25 },
|
||||
{ OV( 985), 20 },
|
||||
{ OV( 993), 15 },
|
||||
{ OV( 999), 10 },
|
||||
{ OV(1004), 5 },
|
||||
{ OV(1008), 0 },
|
||||
{ OV(1012), -5 },
|
||||
{ OV(1016), -10 },
|
||||
{ OV(1020), -15 }
|
||||
};
|
||||
|
|
@ -52,163 +52,190 @@ typedef struct { raw_adc_t value; celsius_t celsius; } temp_entry_t;
|
|||
#define PtAdVal(T,R0,Rup) (short)(1024 / (Rup / PtRt(T, R0) + 1))
|
||||
#define PtLine(T,R0,Rup) { OV(PtAdVal(T, R0, Rup)), T }
|
||||
|
||||
#if ANY_THERMISTOR_IS(1) // beta25 = 4092 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "EPCOS"
|
||||
//
|
||||
// Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
//
|
||||
|
||||
#if ANY_THERMISTOR_IS(1) // beta25 = 4092 K, R25 = 100kΩ, Pullup = 4.7kΩ, "EPCOS"
|
||||
#include "thermistor_1.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(2) // 4338 K, R25 = 200 kOhm, Pull-up = 4.7 kOhm, "ATC Semitec 204GT-2"
|
||||
#include "thermistor_2.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(3) // beta25 = 4120 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Mendel-parts"
|
||||
#include "thermistor_3.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(4) // beta25 = 3950 K, R25 = 10 kOhm, Pull-up = 4.7 kOhm, "Generic"
|
||||
#include "thermistor_4.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(5) // beta25 = 4267 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "ParCan, ATC 104GT-2"
|
||||
#include "thermistor_5.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(501) // 100K Zonestar thermistor
|
||||
#include "thermistor_501.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(502) // Unknown thermistor used by the Zonestar Průša P802M hot bed
|
||||
#include "thermistor_502.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(503) // Zonestar (Z8XM2) Heated Bed thermistor
|
||||
#include "thermistor_503.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(504) // Zonestar (P802QR2 Hot End) thermistors
|
||||
#include "thermistor_504.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(505) // Zonestar (P802QR2 Bed) thermistor
|
||||
#include "thermistor_505.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(512) // 100k thermistor in RPW-Ultra hotend, Pull-up = 4.7 kOhm, "unknown model"
|
||||
#include "thermistor_512.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(6) // beta25 = 4092 K, R25 = 100 kOhm, Pull-up = 8.2 kOhm, "EPCOS ?"
|
||||
#include "thermistor_6.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(7) // beta25 = 3974 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Honeywell 135-104LAG-J01"
|
||||
#include "thermistor_7.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(71) // beta25 = 3974 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Honeywell 135-104LAF-J01"
|
||||
#include "thermistor_71.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(8) // beta25 = 3950 K, R25 = 100 kOhm, Pull-up = 10 kOhm, "Vishay E3104FHT"
|
||||
#include "thermistor_8.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(9) // beta25 = 3960 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "GE Sensing AL03006-58.2K-97-G1"
|
||||
#include "thermistor_9.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(10) // beta25 = 3960 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "RS 198-961"
|
||||
#include "thermistor_10.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(11) // beta25 = 3950 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "QU-BD silicone bed, QWG-104F-3950"
|
||||
#include "thermistor_11.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(13) // beta25 = 4100 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Hisens"
|
||||
#include "thermistor_13.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(15) // JGAurora A5 thermistor calibration
|
||||
#include "thermistor_15.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(17) // Dagoma NTC 100k white thermistor
|
||||
#include "thermistor_17.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(18) // ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
|
||||
#include "thermistor_18.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(20) // Pt100 with INA826 amp on Ultimaker v2.0 electronics
|
||||
#include "thermistor_20.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(21) // Pt100 with INA826 amp with 3.3v excitation based on "Pt100 with INA826 amp on Ultimaker v2.0 electronics"
|
||||
#include "thermistor_21.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(22) // Thermistor in a Rostock 301 hot end, calibrated with a multimeter
|
||||
#include "thermistor_22.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(23) // By AluOne #12622. Formerly 22 above. May need calibration/checking.
|
||||
#include "thermistor_23.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(30) // Kis3d Silicone mat 24V 200W/300W with 6mm Precision cast plate (EN AW 5083)
|
||||
#include "thermistor_30.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(51) // beta25 = 4092 K, R25 = 100 kOhm, Pull-up = 1 kOhm, "EPCOS"
|
||||
#include "thermistor_51.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(52) // beta25 = 4338 K, R25 = 200 kOhm, Pull-up = 1 kOhm, "ATC Semitec 204GT-2"
|
||||
#include "thermistor_52.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(55) // beta25 = 4267 K, R25 = 100 kOhm, Pull-up = 1 kOhm, "ATC Semitec 104GT-2 (Used on ParCan)"
|
||||
#include "thermistor_55.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(60) // beta25 = 3950 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Maker's Tool Works Kapton Bed"
|
||||
#include "thermistor_60.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(61) // beta25 = 3950 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Formbot 350°C Thermistor"
|
||||
#include "thermistor_61.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(66) // beta25 = 4500 K, R25 = 2.5 MOhm, Pull-up = 4.7 kOhm, "DyzeDesign 500 °C Thermistor"
|
||||
#include "thermistor_66.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(67) // R25 = 500 KOhm, beta25 = 3800 K, 4.7 kOhm pull-up, SliceEngineering 450 °C Thermistor
|
||||
#include "thermistor_67.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(68) // PT-100 with Dyze amplifier board
|
||||
#include "thermistor_68.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(12) // beta25 = 4700 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Personal calibration for Makibox hot bed"
|
||||
#include "thermistor_12.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(70) // beta25 = 4100 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Hephestos 2, bqh2 stock thermistor"
|
||||
#include "thermistor_70.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(75) // beta25 = 4100 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "MGB18-104F39050L32 thermistor"
|
||||
#include "thermistor_75.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(99) // 100k bed thermistor with a 10K pull-up resistor (on some Wanhao i3 models)
|
||||
#include "thermistor_99.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(110) // Pt100 with 1k0 pullup
|
||||
#include "thermistor_110.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(147) // Pt100 with 4k7 pullup
|
||||
#include "thermistor_147.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(201) // Pt100 with LMV324 Overlord
|
||||
#include "thermistor_201.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(202) // 200K thermistor in Copymaker3D hotend
|
||||
#include "thermistor_202.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(331) // Like table 1, but with 3V3 as input voltage for MEGA
|
||||
#if ANY_THERMISTOR_IS(331) // Like table 1, but with 3V3 as input voltage for MEGA
|
||||
#include "thermistor_331.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(332) // Like table 1, but with 3V3 as input voltage for DUE
|
||||
#if ANY_THERMISTOR_IS(332) // Like table 1, but with 3V3 as input voltage for DUE
|
||||
#include "thermistor_332.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(666) // beta25 = UNK, R25 = 200K, Pull-up = 10 kOhm, "Unidentified 200K NTC thermistor (Einstart S)"
|
||||
#if ANY_THERMISTOR_IS(2) // 4338 K, R25 = 200kΩ, Pullup = 4.7kΩ, "ATC Semitec 204GT-2"
|
||||
#include "thermistor_2.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(202) // 200K thermistor in Copymaker3D hotend
|
||||
#include "thermistor_202.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(3) // beta25 = 4120 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Mendel-parts"
|
||||
#include "thermistor_3.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(4) // beta25 = 3950 K, R25 = 10kΩ, Pullup = 4.7kΩ, "Generic"
|
||||
#include "thermistor_4.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(5) // beta25 = 4267 K, R25 = 100kΩ, Pullup = 4.7kΩ, "ParCan, ATC 104GT-2"
|
||||
#include "thermistor_5.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(501) // 100K Zonestar thermistor
|
||||
#include "thermistor_501.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(502) // Unknown thermistor used by the Zonestar Průša P802M hot bed
|
||||
#include "thermistor_502.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(503) // Zonestar (Z8XM2) Heated Bed thermistor
|
||||
#include "thermistor_503.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(504) // Zonestar (P802QR2 Hot End) thermistors
|
||||
#include "thermistor_504.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(505) // Zonestar (P802QR2 Bed) thermistor
|
||||
#include "thermistor_505.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(512) // 100k thermistor in RPW-Ultra hotend, Pullup = 4.7kΩ, "unknown model"
|
||||
#include "thermistor_512.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(6) // beta25 = 4092 K, R25 = 100kΩ, Pullup = 8.2kΩ, "EPCOS ?"
|
||||
#include "thermistor_6.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(7) // beta25 = 3974 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Honeywell 135-104LAG-J01"
|
||||
#include "thermistor_7.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(71) // beta25 = 3974 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Honeywell 135-104LAF-J01"
|
||||
#include "thermistor_71.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(8) // beta25 = 3950 K, R25 = 100kΩ, Pullup = 10kΩ, "Vishay E3104FHT"
|
||||
#include "thermistor_8.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(9) // beta25 = 3960 K, R25 = 100kΩ, Pullup = 4.7kΩ, "GE Sensing AL03006-58.2K-97-G1"
|
||||
#include "thermistor_9.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(10) // beta25 = 3960 K, R25 = 100kΩ, Pullup = 4.7kΩ, "RS 198-961"
|
||||
#include "thermistor_10.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(11) // beta25 = 3950 K, R25 = 100kΩ, Pullup = 4.7kΩ, "QU-BD silicone bed, QWG-104F-3950"
|
||||
#include "thermistor_11.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(12) // beta25 = 4700 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Personal calibration for Makibox hot bed"
|
||||
#include "thermistor_12.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(13) // beta25 = 4100 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Hisens"
|
||||
#include "thermistor_13.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(14) // beta25 = 4092 K, R25 = 100kΩ, Pullup = 4.7kΩ, "EPCOS" for hot bed
|
||||
#include "thermistor_14.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(15) // JGAurora A5 thermistor calibration
|
||||
#include "thermistor_15.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(17) // Dagoma NTC 100k white thermistor
|
||||
#include "thermistor_17.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(18) // ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
|
||||
#include "thermistor_18.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(22) // Thermistor in a Rostock 301 hot end, calibrated with a multimeter
|
||||
#include "thermistor_22.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(23) // By AluOne #12622. Formerly 22 above. May need calibration/checking.
|
||||
#include "thermistor_23.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(30) // Kis3d Silicone mat 24V 200W/300W with 6mm Precision cast plate (EN AW 5083)
|
||||
#include "thermistor_30.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(60) // beta25 = 3950 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Maker's Tool Works Kapton Bed"
|
||||
#include "thermistor_60.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(61) // beta25 = 3950 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Formbot 350°C Thermistor"
|
||||
#include "thermistor_61.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(66) // beta25 = 4500 K, R25 = 2.5MΩ, Pullup = 4.7kΩ, "DyzeDesign 500 °C Thermistor"
|
||||
#include "thermistor_66.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(67) // R25 = 500kΩ, beta25 = 3800 K, 4.7kΩ pull-up, SliceEngineering 450 °C Thermistor
|
||||
#include "thermistor_67.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(68) // PT-100 with Dyze amplifier board
|
||||
#include "thermistor_68.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(70) // beta25 = 4100 K, R25 = 100kΩ, Pullup = 4.7kΩ, "Hephestos 2, bqh2 stock thermistor"
|
||||
#include "thermistor_70.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(75) // beta25 = 4100 K, R25 = 100kΩ, Pullup = 4.7kΩ, "MGB18-104F39050L32 thermistor"
|
||||
#include "thermistor_75.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(666) // beta25 = UNK, R25 = 200K, Pullup = 10kΩ, "Unidentified 200K NTC thermistor (Einstart S)"
|
||||
#include "thermistor_666.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1010) // Pt1000 with 1k0 pullup
|
||||
#include "thermistor_1010.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1022) // Pt1000 with 2k2 pullup
|
||||
#include "thermistor_1022.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1047) // Pt1000 with 4k7 pullup
|
||||
#include "thermistor_1047.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(2000) // "Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor" https://product.tdk.com/en/search/sensor/ntc/chip-ntc-thermistor/info?part_no=NTCG104LH104KT1
|
||||
#if ANY_THERMISTOR_IS(2000) // "Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor" https://product.tdk.com/en/search/sensor/ntc/chip-ntc-thermistor/info?part_no=NTCG104LH104KT1
|
||||
#include "thermistor_2000.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(998) // User-defined table 1
|
||||
|
||||
//
|
||||
// Analog Thermistors - 1kΩ pullup
|
||||
//
|
||||
|
||||
#if ANY_THERMISTOR_IS(51) // beta25 = 4092 K, R25 = 100kΩ, Pullup = 1kΩ, "EPCOS"
|
||||
#include "thermistor_51.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(52) // beta25 = 4338 K, R25 = 200kΩ, Pullup = 1kΩ, "ATC Semitec 204GT-2"
|
||||
#include "thermistor_52.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(55) // beta25 = 4267 K, R25 = 100kΩ, Pullup = 1kΩ, "ATC Semitec 104GT-2 (Used on ParCan)"
|
||||
#include "thermistor_55.h"
|
||||
#endif
|
||||
|
||||
//
|
||||
// Analog Thermistors - 10kΩ pullup - Atypical
|
||||
//
|
||||
|
||||
#if ANY_THERMISTOR_IS(99) // 100k bed thermistor with a 10K pull-up resistor (on some Wanhao i3 models)
|
||||
#include "thermistor_99.h"
|
||||
#endif
|
||||
|
||||
//
|
||||
// Analog RTDs (Pt100/Pt1000)
|
||||
//
|
||||
|
||||
#if ANY_THERMISTOR_IS(110) // Pt100 with 1k0 pullup
|
||||
#include "thermistor_110.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(147) // Pt100 with 4k7 pullup
|
||||
#include "thermistor_147.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1010) // Pt1000 with 1k0 pullup
|
||||
#include "thermistor_1010.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1022) // Pt1000 with 2k2 pullup
|
||||
#include "thermistor_1022.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1047) // Pt1000 with 4k7 pullup
|
||||
#include "thermistor_1047.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(20) // Pt100 with INA826 amp on Ultimaker v2.0 electronics
|
||||
#include "thermistor_20.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(21) // Pt100 with INA826 amp with 3.3v excitation based on "Pt100 with INA826 amp on Ultimaker v2.0 electronics"
|
||||
#include "thermistor_21.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(201) // Pt100 with LMV324 Overlord
|
||||
#include "thermistor_201.h"
|
||||
#endif
|
||||
|
||||
//
|
||||
// Custom/Dummy/Other Thermal Sensors
|
||||
//
|
||||
|
||||
#if ANY_THERMISTOR_IS(998) // User-defined table 1
|
||||
#include "thermistor_998.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(999) // User-defined table 2
|
||||
#if ANY_THERMISTOR_IS(999) // User-defined table 2
|
||||
#include "thermistor_999.h"
|
||||
#endif
|
||||
#if ANY_THERMISTOR_IS(1000) // Custom
|
||||
#if ANY_THERMISTOR_IS(1000) // Custom
|
||||
constexpr temp_entry_t temptable_1000[] PROGMEM = { { 0, 0 } };
|
||||
#endif
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue