mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-27 05:48:43 +00:00
Unify step pulse timing of ISR / babystep (#16813)
This commit is contained in:
Scott Lahteine
GitHub
parent
d8b2726fd3
commit
2836834d7e
@ -402,6 +402,7 @@ constexpr uint32_t NS_TO_PULSE_TIMER_TICKS(uint32_t NS) { return (NS + (NS_PER_P
|
||||
#define PULSE_HIGH_TICK_COUNT hal_timer_t(NS_TO_PULSE_TIMER_TICKS(_MIN_PULSE_HIGH_NS - _MIN(_MIN_PULSE_HIGH_NS, TIMER_SETUP_NS)))
|
||||
#define PULSE_LOW_TICK_COUNT hal_timer_t(NS_TO_PULSE_TIMER_TICKS(_MIN_PULSE_LOW_NS - _MIN(_MIN_PULSE_LOW_NS, TIMER_SETUP_NS)))
|
||||
|
||||
#define USING_TIMED_PULSE() hal_timer_t end_tick_count = 0
|
||||
#define START_TIMED_PULSE(DIR) (end_tick_count = HAL_timer_get_count(PULSE_TIMER_NUM) + PULSE_##DIR##_TICK_COUNT)
|
||||
#define AWAIT_TIMED_PULSE() while (HAL_timer_get_count(PULSE_TIMER_NUM) < end_tick_count) { }
|
||||
#define START_HIGH_PULSE() START_TIMED_PULSE(HIGH)
|
||||
@ -409,6 +410,18 @@ constexpr uint32_t NS_TO_PULSE_TIMER_TICKS(uint32_t NS) { return (NS + (NS_PER_P
|
||||
#define AWAIT_HIGH_PULSE() AWAIT_TIMED_PULSE()
|
||||
#define AWAIT_LOW_PULSE() AWAIT_TIMED_PULSE()
|
||||
|
||||
#if MINIMUM_STEPPER_PRE_DIR_DELAY > 0
|
||||
#define DIR_WAIT_BEFORE() DELAY_NS(MINIMUM_STEPPER_PRE_DIR_DELAY)
|
||||
#else
|
||||
#define DIR_WAIT_BEFORE()
|
||||
#endif
|
||||
|
||||
#if MINIMUM_STEPPER_POST_DIR_DELAY > 0
|
||||
#define DIR_WAIT_AFTER() DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY)
|
||||
#else
|
||||
#define DIR_WAIT_AFTER()
|
||||
#endif
|
||||
|
||||
void Stepper::wake_up() {
|
||||
// TCNT1 = 0;
|
||||
ENABLE_STEPPER_DRIVER_INTERRUPT();
|
||||
@ -423,9 +436,7 @@ void Stepper::wake_up() {
|
||||
*/
|
||||
void Stepper::set_directions() {
|
||||
|
||||
#if MINIMUM_STEPPER_PRE_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_PRE_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_BEFORE();
|
||||
|
||||
#define SET_STEP_DIR(A) \
|
||||
if (motor_direction(_AXIS(A))) { \
|
||||
@ -494,10 +505,7 @@ void Stepper::set_directions() {
|
||||
}
|
||||
#endif
|
||||
|
||||
// A small delay may be needed after changing direction
|
||||
#if MINIMUM_STEPPER_POST_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_AFTER();
|
||||
}
|
||||
|
||||
#if ENABLED(S_CURVE_ACCELERATION)
|
||||
@ -1488,12 +1496,12 @@ void Stepper::stepper_pulse_phase_isr() {
|
||||
// Take multiple steps per interrupt (For high speed moves)
|
||||
#if ISR_MULTI_STEPS
|
||||
bool firstStep = true;
|
||||
hal_timer_t end_tick_count = 0;
|
||||
USING_TIMED_PULSE();
|
||||
#endif
|
||||
xyze_bool_t step_needed{0};
|
||||
|
||||
do {
|
||||
#define _APPLY_STEP(AXIS) AXIS ##_APPLY_STEP
|
||||
#define _APPLY_STEP(AXIS, INV, ALWAYS) AXIS ##_APPLY_STEP(INV, ALWAYS)
|
||||
#define _INVERT_STEP_PIN(AXIS) INVERT_## AXIS ##_STEP_PIN
|
||||
|
||||
// Determine if a pulse is needed using Bresenham
|
||||
@ -1509,14 +1517,14 @@ void Stepper::stepper_pulse_phase_isr() {
|
||||
// Start an active pulse, if Bresenham says so, and update position
|
||||
#define PULSE_START(AXIS) do{ \
|
||||
if (step_needed[_AXIS(AXIS)]) { \
|
||||
_APPLY_STEP(AXIS)(!_INVERT_STEP_PIN(AXIS), 0); \
|
||||
_APPLY_STEP(AXIS, !_INVERT_STEP_PIN(AXIS), 0); \
|
||||
} \
|
||||
}while(0)
|
||||
|
||||
// Stop an active pulse, if any, and adjust error term
|
||||
#define PULSE_STOP(AXIS) do { \
|
||||
if (step_needed[_AXIS(AXIS)]) { \
|
||||
_APPLY_STEP(AXIS)(_INVERT_STEP_PIN(AXIS), 0); \
|
||||
_APPLY_STEP(AXIS, _INVERT_STEP_PIN(AXIS), 0); \
|
||||
} \
|
||||
}while(0)
|
||||
|
||||
@ -1978,9 +1986,7 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
||||
else
|
||||
interval = LA_ADV_NEVER;
|
||||
|
||||
#if MINIMUM_STEPPER_PRE_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_PRE_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_BEFORE();
|
||||
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
// We don't know which steppers will be stepped because LA loop follows,
|
||||
@ -1996,17 +2002,14 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
||||
REV_E_DIR(stepper_extruder);
|
||||
#endif
|
||||
|
||||
// A small delay may be needed after changing direction
|
||||
#if MINIMUM_STEPPER_POST_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_AFTER();
|
||||
|
||||
//const hal_timer_t added_step_ticks = hal_timer_t(ADDED_STEP_TICKS);
|
||||
|
||||
// Step E stepper if we have steps
|
||||
#if ISR_MULTI_STEPS
|
||||
bool firstStep = true;
|
||||
hal_timer_t end_tick_count = 0;
|
||||
USING_TIMED_PULSE();
|
||||
#endif
|
||||
|
||||
while (LA_steps) {
|
||||
@ -2424,57 +2427,52 @@ void Stepper::report_positions() {
|
||||
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
#define STEP_PULSE_CYCLES ((MINIMUM_STEPPER_PULSE) * CYCLES_PER_MICROSECOND)
|
||||
#else
|
||||
#define STEP_PULSE_CYCLES 0
|
||||
#endif
|
||||
|
||||
#if ENABLED(DELTA)
|
||||
#define CYCLES_EATEN_BABYSTEP (2 * 15)
|
||||
#else
|
||||
#define CYCLES_EATEN_BABYSTEP 0
|
||||
#endif
|
||||
#define EXTRA_CYCLES_BABYSTEP (STEP_PULSE_CYCLES - (CYCLES_EATEN_BABYSTEP))
|
||||
|
||||
#define _ENABLE_AXIS(AXIS) ENABLE_AXIS_## AXIS()
|
||||
#define _READ_DIR(AXIS) AXIS ##_DIR_READ()
|
||||
#define _INVERT_DIR(AXIS) INVERT_## AXIS ##_DIR
|
||||
#define _APPLY_DIR(AXIS, INVERT) AXIS ##_APPLY_DIR(INVERT, true)
|
||||
|
||||
#if EXTRA_CYCLES_BABYSTEP > 20
|
||||
#define _SAVE_START const hal_timer_t pulse_start = HAL_timer_get_count(PULSE_TIMER_NUM)
|
||||
#define _PULSE_WAIT while (EXTRA_CYCLES_BABYSTEP > (uint32_t)(HAL_timer_get_count(PULSE_TIMER_NUM) - pulse_start) * (PULSE_TIMER_PRESCALE)) { /* nada */ }
|
||||
#else
|
||||
#define _SAVE_START NOOP
|
||||
#if EXTRA_CYCLES_BABYSTEP > 0
|
||||
#define _PULSE_WAIT DELAY_NS(EXTRA_CYCLES_BABYSTEP * NANOSECONDS_PER_CYCLE)
|
||||
#elif ENABLED(DELTA)
|
||||
#define _PULSE_WAIT DELAY_US(2);
|
||||
#elif STEP_PULSE_CYCLES > 0
|
||||
#define _PULSE_WAIT NOOP
|
||||
#else
|
||||
#define _PULSE_WAIT DELAY_US(4);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define BABYSTEP_AXIS(AXIS, INVERT, DIR) { \
|
||||
#if DISABLED(DELTA)
|
||||
#define BABYSTEP_AXIS(AXIS, INV, DIR) do{ \
|
||||
const uint8_t old_dir = _READ_DIR(AXIS); \
|
||||
_ENABLE_AXIS(AXIS); \
|
||||
DELAY_NS(MINIMUM_STEPPER_PRE_DIR_DELAY); \
|
||||
_APPLY_DIR(AXIS, _INVERT_DIR(AXIS)^DIR^INVERT); \
|
||||
DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY); \
|
||||
_SAVE_START; \
|
||||
_APPLY_STEP(AXIS)(!_INVERT_STEP_PIN(AXIS), true); \
|
||||
_PULSE_WAIT; \
|
||||
_APPLY_STEP(AXIS)(_INVERT_STEP_PIN(AXIS), true); \
|
||||
DIR_WAIT_BEFORE(); \
|
||||
_APPLY_DIR(AXIS, _INVERT_DIR(AXIS)^DIR^INV); \
|
||||
DIR_WAIT_AFTER(); \
|
||||
USING_TIMED_PULSE(); \
|
||||
START_HIGH_PULSE(); \
|
||||
_APPLY_STEP(AXIS, !_INVERT_STEP_PIN(AXIS), true); \
|
||||
AWAIT_HIGH_PULSE(); \
|
||||
_APPLY_STEP(AXIS, _INVERT_STEP_PIN(AXIS), true); \
|
||||
_APPLY_DIR(AXIS, old_dir); \
|
||||
}
|
||||
}while(0)
|
||||
#endif
|
||||
|
||||
#if IS_CORE
|
||||
#define BABYSTEP_CORE(A, B, INV, DIR) do{ \
|
||||
const xy_byte_t old_dir = { _READ_DIR(A), _READ_DIR(B) }; \
|
||||
_ENABLE_AXIS(A); _ENABLE_AXIS(B); \
|
||||
DIR_WAIT_BEFORE(); \
|
||||
_APPLY_DIR(A, _INVERT_DIR(A)^DIR^INV); \
|
||||
_APPLY_DIR(B, _INVERT_DIR(B)^DIR^INV^(CORESIGN(1)<0)); \
|
||||
DIR_WAIT_AFTER(); \
|
||||
USING_TIMED_PULSE(); \
|
||||
START_HIGH_PULSE(); \
|
||||
_APPLY_STEP(A, !_INVERT_STEP_PIN(A), true); \
|
||||
_APPLY_STEP(B, !_INVERT_STEP_PIN(B), true); \
|
||||
AWAIT_HIGH_PULSE(); \
|
||||
_APPLY_STEP(A, _INVERT_STEP_PIN(A), true); \
|
||||
_APPLY_STEP(B, _INVERT_STEP_PIN(B), true); \
|
||||
_APPLY_DIR(A, old_dir.a); _APPLY_DIR(B, old_dir.b); \
|
||||
}while(0)
|
||||
#endif
|
||||
|
||||
// MUST ONLY BE CALLED BY AN ISR,
|
||||
// No other ISR should ever interrupt this!
|
||||
void Stepper::babystep(const AxisEnum axis, const bool direction) {
|
||||
cli();
|
||||
DISABLE_ISRS();
|
||||
|
||||
USING_TIMED_PULSE();
|
||||
|
||||
switch (axis) {
|
||||
|
||||
@ -2482,11 +2480,9 @@ void Stepper::report_positions() {
|
||||
|
||||
case X_AXIS:
|
||||
#if CORE_IS_XY
|
||||
BABYSTEP_AXIS(X, false, direction);
|
||||
BABYSTEP_AXIS(Y, false, direction);
|
||||
BABYSTEP_CORE(X, Y, false, direction);
|
||||
#elif CORE_IS_XZ
|
||||
BABYSTEP_AXIS(X, false, direction);
|
||||
BABYSTEP_AXIS(Z, false, direction);
|
||||
BABYSTEP_CORE(X, Z, false, direction);
|
||||
#else
|
||||
BABYSTEP_AXIS(X, false, direction);
|
||||
#endif
|
||||
@ -2494,11 +2490,9 @@ void Stepper::report_positions() {
|
||||
|
||||
case Y_AXIS:
|
||||
#if CORE_IS_XY
|
||||
BABYSTEP_AXIS(X, false, direction);
|
||||
BABYSTEP_AXIS(Y, false, direction^(CORESIGN(1)<0));
|
||||
BABYSTEP_CORE(X, Y, false, direction);
|
||||
#elif CORE_IS_YZ
|
||||
BABYSTEP_AXIS(Y, false, direction);
|
||||
BABYSTEP_AXIS(Z, false, direction^(CORESIGN(1)<0));
|
||||
BABYSTEP_CORE(Y, Z, false, direction);
|
||||
#else
|
||||
BABYSTEP_AXIS(Y, false, direction);
|
||||
#endif
|
||||
@ -2509,13 +2503,9 @@ void Stepper::report_positions() {
|
||||
case Z_AXIS: {
|
||||
|
||||
#if CORE_IS_XZ
|
||||
BABYSTEP_AXIS(X, BABYSTEP_INVERT_Z, direction);
|
||||
BABYSTEP_AXIS(Z, BABYSTEP_INVERT_Z, direction^(CORESIGN(1)<0));
|
||||
|
||||
BABYSTEP_CORE(X, Z, BABYSTEP_INVERT_Z, direction);
|
||||
#elif CORE_IS_YZ
|
||||
BABYSTEP_AXIS(Y, BABYSTEP_INVERT_Z, direction);
|
||||
BABYSTEP_AXIS(Z, BABYSTEP_INVERT_Z, direction^(CORESIGN(1)<0));
|
||||
|
||||
BABYSTEP_CORE(Y, Z, BABYSTEP_INVERT_Z, direction);
|
||||
#elif DISABLED(DELTA)
|
||||
BABYSTEP_AXIS(Z, BABYSTEP_INVERT_Z, direction);
|
||||
|
||||
@ -2527,38 +2517,32 @@ void Stepper::report_positions() {
|
||||
ENABLE_AXIS_Y();
|
||||
ENABLE_AXIS_Z();
|
||||
|
||||
#if MINIMUM_STEPPER_PRE_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_PRE_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_BEFORE();
|
||||
|
||||
const uint8_t old_x_dir_pin = X_DIR_READ(),
|
||||
old_y_dir_pin = Y_DIR_READ(),
|
||||
old_z_dir_pin = Z_DIR_READ();
|
||||
const xyz_byte_t old_dir = { X_DIR_READ(), Y_DIR_READ(), Z_DIR_READ() };
|
||||
|
||||
X_DIR_WRITE(INVERT_X_DIR ^ z_direction);
|
||||
Y_DIR_WRITE(INVERT_Y_DIR ^ z_direction);
|
||||
Z_DIR_WRITE(INVERT_Z_DIR ^ z_direction);
|
||||
|
||||
#if MINIMUM_STEPPER_POST_DIR_DELAY > 0
|
||||
DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY);
|
||||
#endif
|
||||
DIR_WAIT_AFTER();
|
||||
|
||||
_SAVE_START;
|
||||
START_HIGH_PULSE();
|
||||
|
||||
X_STEP_WRITE(!INVERT_X_STEP_PIN);
|
||||
Y_STEP_WRITE(!INVERT_Y_STEP_PIN);
|
||||
Z_STEP_WRITE(!INVERT_Z_STEP_PIN);
|
||||
|
||||
_PULSE_WAIT;
|
||||
AWAIT_HIGH_PULSE();
|
||||
|
||||
X_STEP_WRITE(INVERT_X_STEP_PIN);
|
||||
Y_STEP_WRITE(INVERT_Y_STEP_PIN);
|
||||
Z_STEP_WRITE(INVERT_Z_STEP_PIN);
|
||||
|
||||
// Restore direction bits
|
||||
X_DIR_WRITE(old_x_dir_pin);
|
||||
Y_DIR_WRITE(old_y_dir_pin);
|
||||
Z_DIR_WRITE(old_z_dir_pin);
|
||||
X_DIR_WRITE(old_dir.x);
|
||||
Y_DIR_WRITE(old_dir.y);
|
||||
Z_DIR_WRITE(old_dir.z);
|
||||
|
||||
#endif
|
||||
|
||||
@ -2566,7 +2550,9 @@ void Stepper::report_positions() {
|
||||
|
||||
default: break;
|
||||
}
|
||||
sei();
|
||||
|
||||
START_LOW_PULSE(); AWAIT_LOW_PULSE(); // Prevent Stepper::ISR pulsing too soon
|
||||
ENABLE_ISRS(); // Now it's ok for the ISR to run
|
||||
}
|
||||
|
||||
#endif // BABYSTEPPING
|
||||
|
||||
Loading…
Reference in New Issue
Block a user