diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index f0d8913631a..4731a04ed71 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -9,11 +9,11 @@
//Implementation of an idea by Prof Braino to inform user that any changes made
//to THIS file by the user have been successfully uploaded into firmware.
#define STRING_VERSION_CONFIG_H "2012-02-08j" //Personal revision number for changes to THIS file.
-#define STRING_CONFIG_H_AUTHOR "username" //Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "scuba82" //Who made the changes.
// This determines the communication speed of the printer
-#define BAUDRATE 250000
-//#define BAUDRATE 115200
+//#define BAUDRATE 250000
+#define BAUDRATE 115200
//// The following define selects which electronics board you have. Please choose the one that matches your setup
// MEGA/RAMPS up to 1.2 = 3,
@@ -21,9 +21,12 @@
// Gen6 = 5,
// Sanguinololu 1.2 and above = 62
// Ultimaker = 7,
+// Gen7 custom (Alfons3 Version) = 77, "https://github.com/Alfons3/Generation_7_Electronics"
+// Gen7 v1.1, v1.2 = 78
+// Gen7 v1.3 = 79
// Teensylu = 8,
// Gen3+ =9
-#define MOTHERBOARD 7
+#define MOTHERBOARD 77
//===========================================================================
//=============================Thermal Settings ============================
@@ -41,14 +44,14 @@
// 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01
-#define TEMP_SENSOR_0 -1
+#define TEMP_SENSOR_0 6
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30 // (seconds)
-#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
+#define TEMP_HYSTERESIS 3 // (C�) range of +/- temperatures considered "close" to the target one
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
@@ -108,9 +111,9 @@
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
-const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
-const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
-const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
+const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
+const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
+const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
@@ -124,9 +127,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
-#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
+#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
-#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
+#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
@@ -137,7 +140,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
-#define min_software_endstops true //If true, axis won't move to coordinates less than zero.
+#define min_software_endstops false //If true, axis won't move to coordinates less than zero.
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 205
#define Y_MAX_LENGTH 205
@@ -149,7 +152,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// default settings
-#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker
+#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,2560,760*1.1} // default steps per unit for ultimaker
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
@@ -170,18 +173,18 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support
-//#define EEPROM_SETTINGS
+#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can.
-//#define EEPROM_CHITCHAT
+#define EEPROM_CHITCHAT
//LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2
#define SDSUPPORT // Enable SD Card Support in Hardware Console
-//#define ULTIPANEL
+#define ULTIPANEL
#ifdef ULTIPANEL
- //#define NEWPANEL //enable this if you have a click-encoder panel
+ #define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
diff --git a/Marlin/Gen7/boards.txt b/Marlin/Gen7/boards.txt
new file mode 100644
index 00000000000..d6fbaeeb956
--- /dev/null
+++ b/Marlin/Gen7/boards.txt
@@ -0,0 +1,101 @@
+##############################################################
+
+Gen7-644-16.name=Gen7 with ATmega644 and 16 MHz
+Gen7-644-16.upload.protocol=stk500v2
+Gen7-644-16.upload.maximum_size=63488
+Gen7-644-16.upload.speed=115200
+Gen7-644-16.bootloader.low_fuses=0xF7
+Gen7-644-16.bootloader.high_fuses=0xD4
+Gen7-644-16.bootloader.extended_fuses=0xFD
+Gen7-644-16.bootloader.path=Gen7
+Gen7-644-16.bootloader.file=bootloader-644-16MHz.hex
+Gen7-644-16.bootloader.unlock_bits=0x3F
+Gen7-644-16.bootloader.lock_bits=0x0F
+Gen7-644-16.build.mcu=atmega644
+Gen7-644-16.build.f_cpu=16000000L
+Gen7-644-16.build.core=arduino
+
+##############################################################
+
+Gen7-644-20.name=Gen7 with ATmega644 and 20 MHz
+Gen7-644-20.upload.protocol=stk500v2
+Gen7-644-20.upload.maximum_size=63488
+Gen7-644-20.upload.speed=115200
+Gen7-644-20.bootloader.low_fuses=0xF7
+Gen7-644-20.bootloader.high_fuses=0xD4
+Gen7-644-20.bootloader.extended_fuses=0xFD
+Gen7-644-20.bootloader.path=Gen7
+Gen7-644-20.bootloader.file=bootloader-644-20MHz.hex
+Gen7-644-20.bootloader.unlock_bits=0x3F
+Gen7-644-20.bootloader.lock_bits=0x0F
+Gen7-644-20.build.mcu=atmega644
+Gen7-644-20.build.f_cpu=20000000L
+Gen7-644-20.build.core=arduino
+
+##############################################################
+
+Gen7-644P-16.name=Gen7 with ATmega644P and 16 MHz
+Gen7-644P-16.upload.protocol=stk500v2
+Gen7-644P-16.upload.maximum_size=63488
+Gen7-644P-16.upload.speed=115200
+Gen7-644P-16.bootloader.low_fuses=0xF7
+Gen7-644P-16.bootloader.high_fuses=0xD4
+Gen7-644P-16.bootloader.extended_fuses=0xFD
+Gen7-644P-16.bootloader.path=Gen7
+Gen7-644P-16.bootloader.file=bootloader-644P-16MHz.hex
+Gen7-644P-16.bootloader.unlock_bits=0x3F
+Gen7-644P-16.bootloader.lock_bits=0x0F
+Gen7-644P-16.build.mcu=atmega644p
+Gen7-644P-16.build.f_cpu=16000000L
+Gen7-644P-16.build.core=arduino
+
+##############################################################
+
+Gen7-644P-20.name=Gen7 with ATmega644P and 20 MHz
+Gen7-644P-20.upload.protocol=stk500v2
+Gen7-644P-20.upload.maximum_size=63488
+Gen7-644P-20.upload.speed=115200
+Gen7-644P-20.bootloader.low_fuses=0xF7
+Gen7-644P-20.bootloader.high_fuses=0xD4
+Gen7-644P-20.bootloader.extended_fuses=0xFD
+Gen7-644P-20.bootloader.path=Gen7
+Gen7-644P-20.bootloader.file=bootloader-644P-20MHz.hex
+Gen7-644P-20.bootloader.unlock_bits=0x3F
+Gen7-644P-20.bootloader.lock_bits=0x0F
+Gen7-644P-20.build.mcu=atmega644p
+Gen7-644P-20.build.f_cpu=20000000L
+Gen7-644P-20.build.core=arduino
+
+##############################################################
+
+Gen7-1284p-16.name=Gen7 with ATmega1284 and 16 MHz
+Gen7-1284p-16.upload.protocol=stk500v2
+Gen7-1284p-16.upload.maximum_size=129024
+Gen7-1284p-16.upload.speed=115200
+Gen7-1284p-16.bootloader.low_fuses=0xF7
+Gen7-1284p-16.bootloader.high_fuses=0xD4
+Gen7-1284p-16.bootloader.extended_fuses=0xFD
+Gen7-1284p-16.bootloader.path=Gen7
+Gen7-1284p-16.bootloader.file=bootloader-1284P-16MHz.hex
+Gen7-1284p-16.bootloader.unlock_bits=0x3F
+Gen7-1284p-16.bootloader.lock_bits=0x2F
+Gen7-1284p-16.build.mcu=atmega1284p
+Gen7-1284p-16.build.f_cpu=16000000L
+Gen7-1284p-16.build.core=arduino
+
+##############################################################
+
+Gen7-1284p-20.name=Gen7 with ATmega1284 and 20 MHz
+Gen7-1284p-20.upload.protocol=stk500v2
+Gen7-1284p-20.upload.maximum_size=129024
+Gen7-1284p-20.upload.speed=115200
+Gen7-1284p-20.bootloader.low_fuses=0xF7
+Gen7-1284p-20.bootloader.high_fuses=0xD4
+Gen7-1284p-20.bootloader.extended_fuses=0xFD
+Gen7-1284p-20.bootloader.path=Gen7
+Gen7-1284p-20.bootloader.file=bootloader-1284P-16MHz.hex
+Gen7-1284p-20.bootloader.unlock_bits=0x3F
+Gen7-1284p-20.bootloader.lock_bits=0x2F
+Gen7-1284p-20.build.mcu=atmega1284p
+Gen7-1284p-20.build.f_cpu=20000000L
+Gen7-1284p-20.build.core=arduino
diff --git a/Marlin/Gen7/bootloaders/Gen7/bootloader-1284P-16MHz.hex b/Marlin/Gen7/bootloaders/Gen7/bootloader-1284P-16MHz.hex
new file mode 100644
index 00000000000..93df372ca3e
--- /dev/null
+++ b/Marlin/Gen7/bootloaders/Gen7/bootloader-1284P-16MHz.hex
@@ -0,0 +1,113 @@
+:020000021000EC
+:10F8000011241FBE8FEF90E49EBF8DBF01C32F92C6
+:10F810003F924F925F926F927F928F929F92AF92A0
+:10F82000BF92CF92DF92EF92FF920F931F93DF93DD
+:10F83000CF93CDB7DEB7C252D1400FB6F894DEBF3A
+:10F840000FBECDBF44245524DD24C25EDE4F188296
+:10F85000CE51D1408824992454013AC20E9428FFF5
+:10F86000282F133059F1143028F4113081F0123060
+:10F8700000F507C0153081F1153030F1163071F701
+:10F880003DC08B3159F711E05BE1D52EE7CF8130D8
+:10F8900041F0C25EDE4F3881CE51D140831709F06E
+:10F8A00019C2D226C25EDE4F2883CE51D14012E06B
+:10F8B000D5CFF82EEE24D82613E0D0CF90E0E82A5A
+:10F8C000F92AD22614E0CACF8E3009F003C2D82616
+:10F8D00015E044245524C2CFE1E0F0E0EC0FFD1F19
+:10F8E000E40DF51D80830894411C511CD8264E144C
+:10F8F0005F0409F0B3CF720116E0B0CF8D1509F0A7
+:10F90000E9C1EAC1CC2447C08D81803311F090E079
+:10F910000AC08F81882311F49EE105C0813011F067
+:10F9200095E001C097E91A821B828D818C838E81BC
+:10F930008D839E831F8247E0E42EF12C88C11A82BA
+:10F9400068E06B8383E58C8394E59D83EBE4EE8331
+:10F9500085E38F8380E3888789878FE58A8782E3C1
+:10F960008B873BE0E32EF12C72C18A81813941F013
+:10F97000823941F0803911F48FE005C080E003C086
+:10F9800082E001C08AE01A828B8323E0E22EF12C10
+:10F990005EC1CC24C3941A8292E0E92EF12C58C1A6
+:10F9A0008D81882311F48EE128C0813011F085E02B
+:10F9B00024C087E922C01A8229E0E1E0F0E0209328
+:10F9C000570084911BC08B81803589F48C818830ED
+:10F9D00039F439E0E2E0F0E03093570084910DC053
+:10F9E00069E0E0E0F0E060935700849106C099E0A0
+:10F9F000E3E0F0E09093570084911A828B831C829D
+:10FA000084E0E82EF12C23C18A8190E0A0E0B0E0F0
+:10FA1000B82EAA24992488248B8190E0A0E0B0E03D
+:10FA2000DC0199278827882A992AAA2ABB2A8D814E
+:10FA300090E0A0E0B0E0882A992AAA2ABB2A8C810B
+:10FA400090E0A0E0B0E0BA2FA92F982F8827882A4D
+:10FA5000992AAA2ABB2A88C0EA81C05EDE4FE883C1
+:10FA6000C052D140C15EDE4F1882CF51D1408B8150
+:10FA7000A82FB0E0C15EDE4F28813981CF51D1403F
+:10FA8000A22BB32B933109F042C075016401CC0C59
+:10FA9000DD1CEE1CFF1C33E0F601E0925B003093AE
+:10FAA0005700E89507B600FCFDCF8E01055F1F4F9C
+:10FAB000F801808161810E5F1F4FA5019401220F23
+:10FAC000331F441F551F362E222490E0822993298C
+:10FAD00061E00C01F90140935B0060935700E895E9
+:10FAE00011240894811C911CA11CB11C129701F7D0
+:10FAF00085E0F601E0925B0080935700E89507B639
+:10FB000000FCFDCF81E180935700E8952DC0FE01F8
+:10FB10003B9620E030E040E050E011977D0100E0AE
+:10FB200010E00894E11CF11C011D111D6081F99980
+:10FB3000FECF1FBAC901880D991D92BD81BD60BD60
+:10FB40000FB6F894FA9AF99A0FBE2F5F3F4F4F4FB6
+:10FB50005F4F2E153F054007510711F03196E6CF54
+:10FB6000820E931EA41EB51E1A826EC09A81CE5DAF
+:10FB7000DE4F9883C252D140CF5DDE4F1882C15212
+:10FB8000D1408B81C82EDD24CF5DDE4FE881F98125
+:10FB9000C152D140CE2ADF2A1A8289818431E1F410
+:10FBA0009601BE016D5F7F4FD501C401880F991F7B
+:10FBB000AA1FBB1FABBFFC0187919691FB018083FD
+:10FBC00091836E5F7F4F0894811C911CA11CB11C16
+:10FBD0002250304049F72EC0BE016D5F7F4F20E0BC
+:10FBE00030E040E050E00894C108D108760100E020
+:10FBF00010E00894C11CD11C0894E11CF11C011DEB
+:10FC0000111DF999FECFC901880D991D92BD81BDC5
+:10FC1000F89A80B5FB018193BF012F5F3F4F4F4F93
+:10FC20005F4F2E153F054007510759F7820E931E6F
+:10FC3000A41EB51E23E0E22EF12CEC0CFD1CFB01F2
+:10FC4000108205C080EC8A8392E0E92EF12CCC244E
+:10FC50008BE10E94C7FEC25EDE4F8881CE51D1404B
+:10FC60000E94C7FE8F2D0E94C7FE8E2D0E94C7FEE8
+:10FC70008EE00E94C7FE85E1D82EC25EDE4FF8817D
+:10FC8000CE51D140DF26DE24DF243E010894611CE2
+:10FC9000711C0AC0F30111913F01812F0E94C7FE20
+:10FCA000D1260894E108F108E114F10499F78D2DAB
+:10FCB0000E94C7FECC2009F044C0C25EDE4FF8812E
+:10FCC000CE51D140FF5FC25EDE4FF883CE51D140AE
+:10FCD000EE24FF2410E0C2CD9981933109F4BCCE0B
+:10FCE0009431B0F4933009F440CE943038F491302C
+:10FCF00009F425CE923009F0A5CF04CE903109F455
+:10FD000001CE913109F445CE963009F09BCF7CCEDF
+:10FD1000983109F458CE993150F4953109F49CCEBC
+:10FD2000953108F423CF963109F08CCF1FCF9B314A
+:10FD300009F436CE9D3109F4E7CD9A3109F082CF2E
+:10FD40003ACECE5DDE4F0FB6F894DEBF0FBECDBF0C
+:10FD5000CF91DF911F910F91FF90EF90DF90CF90A7
+:10FD6000BF90AF909F908F907F906F905F904F90DB
+:10FD70003F902F9008958091C00087FFFCCF089599
+:10FD80008091C00087FFFCCF8091C6000895982F16
+:10FD90008091C00085FFFCCF9093C60008959B0121
+:10FDA000AC0197FF11C08091C00082608093C000B9
+:10FDB00050954095309521953F4F4F4F5F4F60E0F4
+:10FDC00074E284EF90E009C08091C0008D7F809341
+:10FDD000C00060E072E18AE790E00E9447FF2C5F7C
+:10FDE0003F4F4F4F5F4F83E0569547953795279587
+:10FDF0008A95D1F7215030403093C5002093C4003C
+:10FE0000089518B817B81F921F921F920895FFCF38
+:10FE100084B714BE90E083709070892B39F418B8C1
+:10FE200017B81F921F921F920895FFCF88E1809309
+:10FE3000C10060E07EE38EEF9FEF0E94CFFE0E9444
+:10FE400007FC18B817B81F921F921F920895FFCF92
+:10FE500020E030E040E050E013C02F5F3F4F4F4FB5
+:10FE60005F4F21308AE6380788E1480780E058076D
+:10FE700039F418B817B81F921F921F920895FFCF38
+:10FE80008091C00087FFE9CF0E94C0FE0895A1E2E3
+:10FE90001A2EAA1BBB1BFD010DC0AA1FBB1FEE1F04
+:10FEA000FF1FA217B307E407F50720F0A21BB30B4F
+:10FEB000E40BF50B661F771F881F991F1A9469F7CB
+:10FEC00060957095809590959B01AC01BD01CF0127
+:02FED000089593
+:040000031000F800F1
+:00000001FF
diff --git a/Marlin/Gen7/bootloaders/Gen7/bootloader-644-16MHz.hex b/Marlin/Gen7/bootloaders/Gen7/bootloader-644-16MHz.hex
new file mode 100644
index 00000000000..58098693d69
--- /dev/null
+++ b/Marlin/Gen7/bootloaders/Gen7/bootloader-644-16MHz.hex
@@ -0,0 +1,75 @@
+:10F800008FEF90E19EBF8DBF11241FBE5A9A00C09A
+:10F81000CDB7DEB7CD51D140DEBFCDBF1092C50010
+:10F8200088E08093C40088E18093C100EE24FF2427
+:10F8300020E0552400E010E039E0432E9BE0292E23
+:10F84000312C2C0E3D1ECFC14150504060407040C5
+:10F8500011F43FE206C08091C00087FFF5CF3091E0
+:10F86000C600933021F1943028F4913099F0923011
+:10F87000C8F407C0953049F1953000F19630D1F5C4
+:10F8800035C03B3119F491E02BE134C03F3291F5A2
+:10F890003983BBC1313011F0351559F52327532E6B
+:10F8A00092E028C0B32FA0E0232793E023C0832F4A
+:10F8B00090E0A82BB92B232794E01CC03E30C9F45C
+:10F8C000232795E0EE24FF2415C0E1E0F0E0EC0FE3
+:10F8D000FD1FEE0DFF1D30830894E11CF11C232752
+:10F8E000EA16FB0639F4D70196E004C0321709F492
+:10F8F0008CC190E044E755E962E470E0ACCF90E061
+:10F9000044C08D81803311F090E00AC08F8188233C
+:10F9100011F49EE105C0813011F099E001C096E933
+:10F920001A821B828D818C838E818D839E831F82A0
+:10F9300047E050E0F4C01A8288E08B8381E48C8336
+:10F9400086E58D8382E58E8389E48F8383E58887CE
+:10F9500080E589878FE58A8782E38B874BE050E0DB
+:10F96000DEC08A81813941F0823941F0803911F459
+:10F970008FE005C080E003C082E001C08AE01A8207
+:10F980008B8343E050E0CBC091E01A8242E050E02C
+:10F99000C7C08D81882311F48EE124C0813011F01D
+:10F9A00089E020C086E91EC01A82E1E0F0E04092C2
+:10F9B0005700849118C08B81803579F48C81883010
+:10F9C00031F4E2E0F0E04092570084910BC0E0E0B7
+:10F9D000F0E040925700849105C0E3E0F0E04092EF
+:10F9E000570084911A828B831C8244E050E097C0B8
+:10F9F000BC80AA248D81082F10E00A291B29000F42
+:10FA0000111F1A828AC09A8088248B81682F70E027
+:10FA100068297929933109F033C0F7EF0F3F1F07A9
+:10FA200010F0A8013FC023E0F80120935700E895AB
+:10FA300007B600FCFDCFA801D1018C9111962C9145
+:10FA400011971296D22ECC2490E08C299D2921E08A
+:10FA5000FA010C0120935700E89511244E5F5F4F87
+:10FA60006250704051F725E0F80120935700E89567
+:10FA700007B600FCFDCF81E180935700E89512C0E6
+:10FA8000A801FB01D10141BD52BD4F5F5F4F8D9178
+:10FA900080BDFA9AF99AF999FECF3197A1F7A8019A
+:10FAA000460F571F1A828A0138C07A8066248B81DC
+:10FAB000A82FB0E0A629B7291A828981843191F450
+:10FAC000BD019E012D5F3F4FF80185919491F90191
+:10FAD000808391832E5F3F4F0E5F1F4F62507040B7
+:10FAE00099F713C0A801BD019E012D5F3F4F41BD95
+:10FAF00052BD4F5F5F4FF89A80B5F90181939F0126
+:10FB000061507040A1F70A0F1B1FAD014D5F5F4FA1
+:10FB1000F901108204C080EC8A8342E050E090E05A
+:10FB2000FBE1F093C6008091C00086FFFCCF80917E
+:10FB3000C00080648093C0005092C6008091C000D5
+:10FB400086FFFCCF8091C00080648093C000652F49
+:10FB50005093C6008091C00086FFFCCF8091C0000A
+:10FB600080648093C000342F4093C6008091C00011
+:10FB700086FFFCCF8091C00080648093C0008EE03F
+:10FB80008093C6008091C00086FFFCCF8091C000AA
+:10FB900080648093C00025E1252523272627FE01C8
+:10FBA000319610C030813093C6008091C00086FF2E
+:10FBB000FCCF31968091C00080648093C0002327E1
+:10FBC000415050404115510569F72093C60080917E
+:10FBD000C00086FFFCCF8091C00080648093C0008D
+:10FBE000992349F4539444E755E962E470E090E0C6
+:10FBF000A0E0B0E030CE5A9881E180935700E895BC
+:10FC000011241F921F920895FFCF9981933109F417
+:10FC1000FACE9431C8F4963009F4EACE973050F415
+:10FC2000923009F46CCE933009F49BCE913009F0F8
+:10FC300072CF81CE913109F4A7CE923108F0E1CE96
+:10FC4000903109F068CF5BCE983109F4B4CE993188
+:10FC500050F4953109F4D7CE953108F426CF96317A
+:10FC600009F059CF22CF9B3109F493CE9C3120F477
+:10FC70009A3109F050CF98CE9D3109F442CE9F328F
+:06FC800009F049CFB8CFE6
+:040000030000F80001
+:00000001FF
diff --git a/Marlin/Gen7/bootloaders/Gen7/bootloader-644-20MHz.hex b/Marlin/Gen7/bootloaders/Gen7/bootloader-644-20MHz.hex
new file mode 100644
index 00000000000..d216c65f9bf
--- /dev/null
+++ b/Marlin/Gen7/bootloaders/Gen7/bootloader-644-20MHz.hex
@@ -0,0 +1,75 @@
+:10F800008FEF90E19EBF8DBF11241FBE5A9A00C09A
+:10F81000CDB7DEB7CD51D140DEBFCDBF1092C50010
+:10F820008AE08093C40088E18093C100EE24FF2425
+:10F8300020E0552400E010E039E0432E9BE0292E23
+:10F84000312C2C0E3D1ECFC14150504060407040C5
+:10F8500011F43FE206C08091C00087FFF5CF3091E0
+:10F86000C600933021F1943028F4913099F0923011
+:10F87000C8F407C0953049F1953000F19630D1F5C4
+:10F8800035C03B3119F491E02BE134C03F3291F5A2
+:10F890003983BBC1313011F0351559F52327532E6B
+:10F8A00092E028C0B32FA0E0232793E023C0832F4A
+:10F8B00090E0A82BB92B232794E01CC03E30C9F45C
+:10F8C000232795E0EE24FF2415C0E1E0F0E0EC0FE3
+:10F8D000FD1FEE0DFF1D30830894E11CF11C232752
+:10F8E000EA16FB0639F4D70196E004C0321709F492
+:10F8F0008CC190E041ED5AE363E570E0ACCF90E05D
+:10F9000044C08D81803311F090E00AC08F8188233C
+:10F9100011F49EE105C0813011F099E001C096E933
+:10F920001A821B828D818C838E818D839E831F82A0
+:10F9300047E050E0F4C01A8288E08B8381E48C8336
+:10F9400086E58D8382E58E8389E48F8383E58887CE
+:10F9500080E589878FE58A8782E38B874BE050E0DB
+:10F96000DEC08A81813941F0823941F0803911F459
+:10F970008FE005C080E003C082E001C08AE01A8207
+:10F980008B8343E050E0CBC091E01A8242E050E02C
+:10F99000C7C08D81882311F48EE124C0813011F01D
+:10F9A00089E020C086E91EC01A82E1E0F0E04092C2
+:10F9B0005700849118C08B81803579F48C81883010
+:10F9C00031F4E2E0F0E04092570084910BC0E0E0B7
+:10F9D000F0E040925700849105C0E3E0F0E04092EF
+:10F9E000570084911A828B831C8244E050E097C0B8
+:10F9F000BC80AA248D81082F10E00A291B29000F42
+:10FA0000111F1A828AC09A8088248B81682F70E027
+:10FA100068297929933109F033C0F7EF0F3F1F07A9
+:10FA200010F0A8013FC023E0F80120935700E895AB
+:10FA300007B600FCFDCFA801D1018C9111962C9145
+:10FA400011971296D22ECC2490E08C299D2921E08A
+:10FA5000FA010C0120935700E89511244E5F5F4F87
+:10FA60006250704051F725E0F80120935700E89567
+:10FA700007B600FCFDCF81E180935700E89512C0E6
+:10FA8000A801FB01D10141BD52BD4F5F5F4F8D9178
+:10FA900080BDFA9AF99AF999FECF3197A1F7A8019A
+:10FAA000460F571F1A828A0138C07A8066248B81DC
+:10FAB000A82FB0E0A629B7291A828981843191F450
+:10FAC000BD019E012D5F3F4FF80185919491F90191
+:10FAD000808391832E5F3F4F0E5F1F4F62507040B7
+:10FAE00099F713C0A801BD019E012D5F3F4F41BD95
+:10FAF00052BD4F5F5F4FF89A80B5F90181939F0126
+:10FB000061507040A1F70A0F1B1FAD014D5F5F4FA1
+:10FB1000F901108204C080EC8A8342E050E090E05A
+:10FB2000FBE1F093C6008091C00086FFFCCF80917E
+:10FB3000C00080648093C0005092C6008091C000D5
+:10FB400086FFFCCF8091C00080648093C000652F49
+:10FB50005093C6008091C00086FFFCCF8091C0000A
+:10FB600080648093C000342F4093C6008091C00011
+:10FB700086FFFCCF8091C00080648093C0008EE03F
+:10FB80008093C6008091C00086FFFCCF8091C000AA
+:10FB900080648093C00025E1252523272627FE01C8
+:10FBA000319610C030813093C6008091C00086FF2E
+:10FBB000FCCF31968091C00080648093C0002327E1
+:10FBC000415050404115510569F72093C60080917E
+:10FBD000C00086FFFCCF8091C00080648093C0008D
+:10FBE000992349F4539441ED5AE363E570E090E0C2
+:10FBF000A0E0B0E030CE5A9881E180935700E895BC
+:10FC000011241F921F920895FFCF9981933109F417
+:10FC1000FACE9431C8F4963009F4EACE973050F415
+:10FC2000923009F46CCE933009F49BCE913009F0F8
+:10FC300072CF81CE913109F4A7CE923108F0E1CE96
+:10FC4000903109F068CF5BCE983109F4B4CE993188
+:10FC500050F4953109F4D7CE953108F426CF96317A
+:10FC600009F059CF22CF9B3109F493CE9C3120F477
+:10FC70009A3109F050CF98CE9D3109F442CE9F328F
+:06FC800009F049CFB8CFE6
+:040000030000F80001
+:00000001FF
diff --git a/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-16MHz.hex b/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-16MHz.hex
new file mode 100644
index 00000000000..a9105a22174
--- /dev/null
+++ b/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-16MHz.hex
@@ -0,0 +1,75 @@
+:10F800008FEF90E19EBF8DBF11241FBE5A9A00C09A
+:10F81000CDB7DEB7CD51D140DEBFCDBF1092C50010
+:10F8200088E08093C40088E18093C100EE24FF2427
+:10F8300020E0552400E010E039E0432E93E0292E2B
+:10F84000312C2C0E3D1ECDC14150504060407040C7
+:10F8500011F43FE206C08091C00087FFF5CF3091E0
+:10F86000C600933021F1943028F4913099F0923011
+:10F87000C8F407C0953049F1953000F19630D1F5C4
+:10F8800035C03B3119F491E02BE134C03F3291F5A2
+:10F890003983B9C1313011F0351559F52327532E6D
+:10F8A00092E028C0B32FA0E0232793E023C0832F4A
+:10F8B00090E0A82BB92B232794E01CC03E30C9F45C
+:10F8C000232795E0EE24FF2415C0E1E0F0E0EC0FE3
+:10F8D000FD1FEE0DFF1D30830894E11CF11C232752
+:10F8E000EA16FB0639F4D70196E004C0321709F492
+:10F8F0008AC190E044E755E962E470E0ACCF90E063
+:10F9000044C08D81803311F090E00AC08F8188233C
+:10F9100011F49EE105C0813011F09AE001C096E932
+:10F920001A821B828D818C838E818D839E831F82A0
+:10F9300047E050E0F2C01A8288E08B8381E48C8338
+:10F9400086E58D8382E58E8389E48F8383E58887CE
+:10F9500080E589878FE58A8782E38B874BE050E0DB
+:10F96000DCC08A81813941F0823941F0803911F45B
+:10F970008FE005C080E003C082E001C08AE01A8207
+:10F980008B8343E050E0C9C091E01A8242E050E02E
+:10F99000C5C08D81882311F48EE124C0813011F01F
+:10F9A0008AE020C086E91EC01A82E1E0F0E04092C1
+:10F9B0005700849118C08B81803579F48C81883010
+:10F9C00031F4E2E0F0E04092570084910BC0E0E0B7
+:10F9D000F0E040925700849105C0E3E0F0E04092EF
+:10F9E000570084911A828B831C8244E050E095C0BA
+:10F9F000BC80AA248D81082F10E00A291B29000F42
+:10FA0000111F1A8288C09A8088248B81682F70E029
+:10FA100068297929933109F034C0F7EF0F3F1F07A8
+:10FA200010F0A80141C023E0F80120935700E895A9
+:10FA300007B600FCFDCFA801DE011B968C91119644
+:10FA40002C9111971296D22ECC2490E08C299D29CE
+:10FA500021E0FA010C0120935700E89511244E5F34
+:10FA60005F4F6250704051F725E0F8012093570036
+:10FA7000E89507B600FCFDCF81E180935700E8953B
+:10FA800013C0A801FB01DE011B9641BD52BD4F5FB3
+:10FA90005F4F8D9180BDFA9AF99AF999FECF31970F
+:10FAA000A1F7A801460F571F1A828A0134C07A8035
+:10FAB00066248B81A82FB0E0A629B7291A828981F4
+:10FAC000843181F4BD019101F80185919491F9018E
+:10FAD000808391832E5F3F4F0E5F1F4F62507040B7
+:10FAE00099F711C0A801BD01910141BD52BD4F5F01
+:10FAF0005F4FF89A80B5F90181939F016150704082
+:10FB0000A1F70A0F1B1FAD014D5F5F4FF901108276
+:10FB100004C080EC8A8342E050E090E0FBE1F09387
+:10FB2000C6008091C00086FFFCCF8091C000806439
+:10FB30008093C0005092C6008091C00086FFFCCF29
+:10FB40008091C00080648093C000652F5093C600F0
+:10FB50008091C00086FFFCCF8091C00080648093BC
+:10FB6000C000342F4093C6008091C00086FFFCCFB8
+:10FB70008091C00080648093C0008EE08093C600B6
+:10FB80008091C00086FFFCCF8091C000806480938C
+:10FB9000C00025E1252523272627FE01319610C028
+:10FBA00030813093C6008091C00086FFFCCF319633
+:10FBB0008091C00080648093C00023274150504052
+:10FBC0004115510569F72093C6008091C00086FF5A
+:10FBD000FCCF8091C00080648093C000992349F4D9
+:10FBE000539444E755E962E470E090E0A0E0B0E0AF
+:10FBF00032CE5A9881E180935700E89511241F92E4
+:10FC00001F920895FFCF9981933109F4FCCE94316E
+:10FC1000C8F4963009F4ECCE973050F4923009F4E1
+:10FC20006ECE933009F49DCE913009F072CF83CE21
+:10FC3000913109F4A9CE923108F0E3CE903109F068
+:10FC400068CF5DCE983109F4B6CE993150F4953134
+:10FC500009F4D9CE953108F42ACF963109F059CF5D
+:10FC600026CF9B3109F495CE9C3120F49A3109F0CE
+:10FC700050CF9ACE9D3109F444CE9F3209F049CF3E
+:02FC8000B8CFFB
+:040000030000F80001
+:00000001FF
diff --git a/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-20MHz.hex b/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-20MHz.hex
new file mode 100644
index 00000000000..4ee0c6b1fcf
--- /dev/null
+++ b/Marlin/Gen7/bootloaders/Gen7/bootloader-644P-20MHz.hex
@@ -0,0 +1,75 @@
+:10F800008FEF90E19EBF8DBF11241FBE5A9A00C09A
+:10F81000CDB7DEB7CD51D140DEBFCDBF1092C50010
+:10F820008AE08093C40088E18093C100EE24FF2425
+:10F8300020E0552400E010E039E0432E93E0292E2B
+:10F84000312C2C0E3D1ECDC14150504060407040C7
+:10F8500011F43FE206C08091C00087FFF5CF3091E0
+:10F86000C600933021F1943028F4913099F0923011
+:10F87000C8F407C0953049F1953000F19630D1F5C4
+:10F8800035C03B3119F491E02BE134C03F3291F5A2
+:10F890003983B9C1313011F0351559F52327532E6D
+:10F8A00092E028C0B32FA0E0232793E023C0832F4A
+:10F8B00090E0A82BB92B232794E01CC03E30C9F45C
+:10F8C000232795E0EE24FF2415C0E1E0F0E0EC0FE3
+:10F8D000FD1FEE0DFF1D30830894E11CF11C232752
+:10F8E000EA16FB0639F4D70196E004C0321709F492
+:10F8F0008AC190E041ED5AE363E570E0ACCF90E05F
+:10F9000044C08D81803311F090E00AC08F8188233C
+:10F9100011F49EE105C0813011F09AE001C096E932
+:10F920001A821B828D818C838E818D839E831F82A0
+:10F9300047E050E0F2C01A8288E08B8381E48C8338
+:10F9400086E58D8382E58E8389E48F8383E58887CE
+:10F9500080E589878FE58A8782E38B874BE050E0DB
+:10F96000DCC08A81813941F0823941F0803911F45B
+:10F970008FE005C080E003C082E001C08AE01A8207
+:10F980008B8343E050E0C9C091E01A8242E050E02E
+:10F99000C5C08D81882311F48EE124C0813011F01F
+:10F9A0008AE020C086E91EC01A82E1E0F0E04092C1
+:10F9B0005700849118C08B81803579F48C81883010
+:10F9C00031F4E2E0F0E04092570084910BC0E0E0B7
+:10F9D000F0E040925700849105C0E3E0F0E04092EF
+:10F9E000570084911A828B831C8244E050E095C0BA
+:10F9F000BC80AA248D81082F10E00A291B29000F42
+:10FA0000111F1A8288C09A8088248B81682F70E029
+:10FA100068297929933109F034C0F7EF0F3F1F07A8
+:10FA200010F0A80141C023E0F80120935700E895A9
+:10FA300007B600FCFDCFA801DE011B968C91119644
+:10FA40002C9111971296D22ECC2490E08C299D29CE
+:10FA500021E0FA010C0120935700E89511244E5F34
+:10FA60005F4F6250704051F725E0F8012093570036
+:10FA7000E89507B600FCFDCF81E180935700E8953B
+:10FA800013C0A801FB01DE011B9641BD52BD4F5FB3
+:10FA90005F4F8D9180BDFA9AF99AF999FECF31970F
+:10FAA000A1F7A801460F571F1A828A0134C07A8035
+:10FAB00066248B81A82FB0E0A629B7291A828981F4
+:10FAC000843181F4BD019101F80185919491F9018E
+:10FAD000808391832E5F3F4F0E5F1F4F62507040B7
+:10FAE00099F711C0A801BD01910141BD52BD4F5F01
+:10FAF0005F4FF89A80B5F90181939F016150704082
+:10FB0000A1F70A0F1B1FAD014D5F5F4FF901108276
+:10FB100004C080EC8A8342E050E090E0FBE1F09387
+:10FB2000C6008091C00086FFFCCF8091C000806439
+:10FB30008093C0005092C6008091C00086FFFCCF29
+:10FB40008091C00080648093C000652F5093C600F0
+:10FB50008091C00086FFFCCF8091C00080648093BC
+:10FB6000C000342F4093C6008091C00086FFFCCFB8
+:10FB70008091C00080648093C0008EE08093C600B6
+:10FB80008091C00086FFFCCF8091C000806480938C
+:10FB9000C00025E1252523272627FE01319610C028
+:10FBA00030813093C6008091C00086FFFCCF319633
+:10FBB0008091C00080648093C00023274150504052
+:10FBC0004115510569F72093C6008091C00086FF5A
+:10FBD000FCCF8091C00080648093C000992349F4D9
+:10FBE000539441ED5AE363E570E090E0A0E0B0E0AB
+:10FBF00032CE5A9881E180935700E89511241F92E4
+:10FC00001F920895FFCF9981933109F4FCCE94316E
+:10FC1000C8F4963009F4ECCE973050F4923009F4E1
+:10FC20006ECE933009F49DCE913009F072CF83CE21
+:10FC3000913109F4A9CE923108F0E3CE903109F068
+:10FC400068CF5DCE983109F4B6CE993150F4953134
+:10FC500009F4D9CE953108F42ACF963109F059CF5D
+:10FC600026CF9B3109F495CE9C3120F49A3109F0CE
+:10FC700050CF9ACE9D3109F444CE9F3209F049CF3E
+:02FC8000B8CFFB
+:040000030000F80001
+:00000001FF
diff --git a/Marlin/Gen7/cores/arduino/HardwareSerial.cpp b/Marlin/Gen7/cores/arduino/HardwareSerial.cpp
new file mode 100644
index 00000000000..8b1fcc60141
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/HardwareSerial.cpp
@@ -0,0 +1,239 @@
+/*
+ HardwareSerial.cpp - Hardware serial library for Wiring
+ Copyright (c) 2006 Nicholas Zambetti. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+
+ Modified 23 November 2006 by David A. Mellis
+*/
+
+#include <stdio.h>
+#include <string.h>
+#include <inttypes.h>
+#include "wiring.h"
+#include "wiring_private.h"
+
+#include "HardwareSerial.h"
+
+// Define constants and variables for buffering incoming serial data. We're
+// using a ring buffer (I think), in which rx_buffer_head is the index of the
+// location to which to write the next incoming character and rx_buffer_tail
+// is the index of the location from which to read.
+#define RX_BUFFER_SIZE 128
+
+struct ring_buffer {
+ unsigned char buffer[RX_BUFFER_SIZE];
+ int head;
+ int tail;
+};
+
+ring_buffer rx_buffer = { { 0 }, 0, 0 };
+
+#ifdef UDR1
+ring_buffer rx_buffer1 = { { 0 }, 0, 0 };
+#endif
+
+#ifdef UDR2
+ring_buffer rx_buffer2 = { { 0 }, 0, 0 };
+#endif
+#ifdef UDR3
+ring_buffer rx_buffer3 = { { 0 }, 0, 0 };
+#endif
+
+inline void store_char(unsigned char c, ring_buffer *rx_buffer)
+{
+ int i = (rx_buffer->head + 1) % RX_BUFFER_SIZE;
+
+ // if we should be storing the received character into the location
+ // just before the tail (meaning that the head would advance to the
+ // current location of the tail), we're about to overflow the buffer
+ // and so we don't write the character or advance the head.
+ if (i != rx_buffer->tail) {
+ rx_buffer->buffer[rx_buffer->head] = c;
+ rx_buffer->head = i;
+ }
+}
+
+ISR(USART0_RX_vect)
+{
+ unsigned char c = UDR0;
+ store_char(c, &rx_buffer);
+}
+
+#ifdef UDR1
+ISR(USART1_RX_vect)
+{
+ unsigned char c = UDR1;
+ store_char(c, &rx_buffer1);
+}
+
+#ifdef UDR2
+ISR(USART2_RX_vect)
+{
+ unsigned char c = UDR2;
+ store_char(c, &rx_buffer2);
+}
+
+#ifdef UDR2
+ISR(USART3_RX_vect)
+{
+ unsigned char c = UDR3;
+ store_char(c, &rx_buffer3);
+}
+#endif
+#endif
+
+#else
+
+#if defined(__AVR_ATmega8__)
+SIGNAL(SIG_UART_RECV)
+#else
+SIGNAL(USART_RX_vect)
+#endif
+{
+#if defined(__AVR_ATmega8__)
+ unsigned char c = UDR;
+#else
+ unsigned char c = UDR0;
+#endif
+ store_char(c, &rx_buffer);
+}
+
+#endif
+
+// Constructors ////////////////////////////////////////////////////////////////
+
+HardwareSerial::HardwareSerial(ring_buffer *rx_buffer,
+ volatile uint8_t *ubrrh, volatile uint8_t *ubrrl,
+ volatile uint8_t *ucsra, volatile uint8_t *ucsrb,
+ volatile uint8_t *udr,
+ uint8_t rxen, uint8_t txen, uint8_t rxcie, uint8_t udre, uint8_t u2x)
+{
+ _rx_buffer = rx_buffer;
+ _ubrrh = ubrrh;
+ _ubrrl = ubrrl;
+ _ucsra = ucsra;
+ _ucsrb = ucsrb;
+ _udr = udr;
+ _rxen = rxen;
+ _txen = txen;
+ _rxcie = rxcie;
+ _udre = udre;
+ _u2x = u2x;
+}
+
+// Public Methods //////////////////////////////////////////////////////////////
+
+void HardwareSerial::begin(long baud)
+{
+ uint16_t baud_setting;
+ bool use_u2x;
+
+ // U2X mode is needed for baud rates higher than (CPU Hz / 16)
+ if (baud > F_CPU / 16) {
+ use_u2x = true;
+ } else {
+ // figure out if U2X mode would allow for a better connection
+
+ // calculate the percent difference between the baud-rate specified and
+ // the real baud rate for both U2X and non-U2X mode (0-255 error percent)
+ uint8_t nonu2x_baud_error = abs((int)(255-((F_CPU/(16*(((F_CPU/8/baud-1)/2)+1))*255)/baud)));
+ uint8_t u2x_baud_error = abs((int)(255-((F_CPU/(8*(((F_CPU/4/baud-1)/2)+1))*255)/baud)));
+
+ // prefer non-U2X mode because it handles clock skew better
+ use_u2x = (nonu2x_baud_error > u2x_baud_error);
+ }
+
+ if (use_u2x) {
+ *_ucsra = 1 << _u2x;
+ baud_setting = (F_CPU / 4 / baud - 1) / 2;
+ } else {
+ *_ucsra = 0;
+ baud_setting = (F_CPU / 8 / baud - 1) / 2;
+ }
+
+ // assign the baud_setting, a.k.a. ubbr (USART Baud Rate Register)
+ *_ubrrh = baud_setting >> 8;
+ *_ubrrl = baud_setting;
+
+ sbi(*_ucsrb, _rxen);
+ sbi(*_ucsrb, _txen);
+ sbi(*_ucsrb, _rxcie);
+}
+
+void HardwareSerial::end()
+{
+ cbi(*_ucsrb, _rxen);
+ cbi(*_ucsrb, _txen);
+ cbi(*_ucsrb, _rxcie);
+}
+
+uint8_t HardwareSerial::available(void)
+{
+ return (RX_BUFFER_SIZE + _rx_buffer->head - _rx_buffer->tail) % RX_BUFFER_SIZE;
+}
+
+int HardwareSerial::read(void)
+{
+ // if the head isn't ahead of the tail, we don't have any characters
+ if (_rx_buffer->head == _rx_buffer->tail) {
+ return -1;
+ } else {
+ unsigned char c = _rx_buffer->buffer[_rx_buffer->tail];
+ _rx_buffer->tail = (_rx_buffer->tail + 1) % RX_BUFFER_SIZE;
+ return c;
+ }
+}
+
+void HardwareSerial::flush()
+{
+ // don't reverse this or there may be problems if the RX interrupt
+ // occurs after reading the value of rx_buffer_head but before writing
+ // the value to rx_buffer_tail; the previous value of rx_buffer_head
+ // may be written to rx_buffer_tail, making it appear as if the buffer
+ // don't reverse this or there may be problems if the RX interrupt
+ // occurs after reading the value of rx_buffer_head but before writing
+ // the value to rx_buffer_tail; the previous value of rx_buffer_head
+ // may be written to rx_buffer_tail, making it appear as if the buffer
+ // were full, not empty.
+ _rx_buffer->head = _rx_buffer->tail;
+}
+
+void HardwareSerial::write(uint8_t c)
+{
+ while (!((*_ucsra) & (1 << _udre)))
+ ;
+
+ *_udr = c;
+}
+
+// Preinstantiate Objects //////////////////////////////////////////////////////
+
+#if defined(__AVR_ATmega8__)
+HardwareSerial Serial(&rx_buffer, &UBRRH, &UBRRL, &UCSRA, &UCSRB, &UDR, RXEN, TXEN, RXCIE, UDRE, U2X);
+#else
+HardwareSerial Serial(&rx_buffer, &UBRR0H, &UBRR0L, &UCSR0A, &UCSR0B, &UDR0, RXEN0, TXEN0, RXCIE0, UDRE0, U2X0);
+#endif
+
+#ifdef UDR1
+HardwareSerial Serial1(&rx_buffer1, &UBRR1H, &UBRR1L, &UCSR1A, &UCSR1B, &UDR1, RXEN1, TXEN1, RXCIE1, UDRE1, U2X1);
+#endif
+
+#ifdef UDR2
+HardwareSerial Serial2(&rx_buffer2, &UBRR2H, &UBRR2L, &UCSR2A, &UCSR2B, &UDR2, RXEN2, TXEN2, RXCIE2, UDRE2, U2X2);
+#endif
+#ifdef UDR3
+HardwareSerial Serial3(&rx_buffer3, &UBRR3H, &UBRR3L, &UCSR3A, &UCSR3B, &UDR3, RXEN3, TXEN3, RXCIE3, UDRE3, U2X3);
+#endif
diff --git a/Marlin/Gen7/cores/arduino/HardwareSerial.h b/Marlin/Gen7/cores/arduino/HardwareSerial.h
new file mode 100644
index 00000000000..f609f73d3dd
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/HardwareSerial.h
@@ -0,0 +1,69 @@
+/*
+ HardwareSerial.h - Hardware serial library for Wiring
+ Copyright (c) 2006 Nicholas Zambetti. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
+#ifndef HardwareSerial_h
+#define HardwareSerial_h
+
+#include <inttypes.h>
+
+#include "Print.h"
+
+struct ring_buffer;
+
+class HardwareSerial : public Print
+{
+ private:
+ ring_buffer *_rx_buffer;
+ volatile uint8_t *_ubrrh;
+ volatile uint8_t *_ubrrl;
+ volatile uint8_t *_ucsra;
+ volatile uint8_t *_ucsrb;
+ volatile uint8_t *_udr;
+ uint8_t _rxen;
+ uint8_t _txen;
+ uint8_t _rxcie;
+ uint8_t _udre;
+ uint8_t _u2x;
+ public:
+ HardwareSerial(ring_buffer *rx_buffer,
+ volatile uint8_t *ubrrh, volatile uint8_t *ubrrl,
+ volatile uint8_t *ucsra, volatile uint8_t *ucsrb,
+ volatile uint8_t *udr,
+ uint8_t rxen, uint8_t txen, uint8_t rxcie, uint8_t udre, uint8_t u2x);
+ void begin(long);
+ void end();
+ uint8_t available(void);
+ int read(void);
+ void flush(void);
+ virtual void write(uint8_t);
+ using Print::write; // pull in write(str) and write(buf, size) from Print
+};
+
+extern HardwareSerial Serial;
+
+#if defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1280__)
+extern HardwareSerial Serial1;
+#endif
+
+#if defined(__AVR_ATmega1280__)
+extern HardwareSerial Serial2;
+extern HardwareSerial Serial3;
+#endif
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/Makefile b/Marlin/Gen7/cores/arduino/Makefile
new file mode 100644
index 00000000000..571687db98f
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/Makefile
@@ -0,0 +1,243 @@
+# Arduino 0011 Makefile
+# Arduino adaptation by mellis, eighthave, oli.keller
+#
+# This makefile allows you to build sketches from the command line
+# without the Arduino environment (or Java).
+#
+# Detailed instructions for using the makefile:
+#
+# 1. Copy this file into the folder with your sketch. There should be a
+# file with the same name as the folder and with the extension .pde
+# (e.g. foo.pde in the foo/ folder).
+#
+# 2. Modify the line containg "INSTALL_DIR" to point to the directory that
+# contains the Arduino installation (for example, under Mac OS X, this
+# might be /Applications/arduino-0012).
+#
+# 3. Modify the line containing "PORT" to refer to the filename
+# representing the USB or serial connection to your Arduino board
+# (e.g. PORT = /dev/tty.USB0). If the exact name of this file
+# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*).
+#
+# 4. Set the line containing "MCU" to match your board's processor.
+# Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
+# or Diecimila have the atmega168. If you're using a LilyPad Arduino,
+# change F_CPU to 8000000.
+#
+# 5. At the command line, change to the directory containing your
+# program's file and the makefile.
+#
+# 6. Type "make" and press enter to compile/verify your program.
+#
+# 7. Type "make upload", reset your Arduino board, and press enter to
+# upload your program to the Arduino board.
+#
+# $Id$
+
+TARGET = $(notdir $(CURDIR))
+INSTALL_DIR = /Users/dmellis/Source/arduino/trunk/build/macosx/build/work
+PORT = /dev/tty.usb*
+UPLOAD_RATE = 19200
+AVRDUDE_PROGRAMMER = stk500v1
+MCU = atmega168
+F_CPU = 16000000
+
+############################################################################
+# Below here nothing should be changed...
+
+ARDUINO = $(INSTALL_DIR)/hardware/cores/arduino
+AVR_TOOLS_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
+SRC = $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \
+$(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
+$(ARDUINO)/wiring_pulse.c $(ARDUINO)/wiring_serial.c \
+$(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
+CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp
+FORMAT = ihex
+
+
+# Name of this Makefile (used for "make depend").
+MAKEFILE = Makefile
+
+# Debugging format.
+# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
+# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
+DEBUG = stabs
+
+OPT = s
+
+# Place -D or -U options here
+CDEFS = -DF_CPU=$(F_CPU)
+CXXDEFS = -DF_CPU=$(F_CPU)
+
+# Place -I options here
+CINCS = -I$(ARDUINO)
+CXXINCS = -I$(ARDUINO)
+
+# Compiler flag to set the C Standard level.
+# c89 - "ANSI" C
+# gnu89 - c89 plus GCC extensions
+# c99 - ISO C99 standard (not yet fully implemented)
+# gnu99 - c99 plus GCC extensions
+CSTANDARD = -std=gnu99
+CDEBUG = -g$(DEBUG)
+CWARN = -Wall -Wstrict-prototypes
+CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
+#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
+
+CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
+CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT)
+#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs
+LDFLAGS = -lm
+
+
+# Programming support using avrdude. Settings and variables.
+AVRDUDE_PORT = $(PORT)
+AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
+AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf \
+-p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
+-b $(UPLOAD_RATE)
+
+# Program settings
+CC = $(AVR_TOOLS_PATH)/avr-gcc
+CXX = $(AVR_TOOLS_PATH)/avr-g++
+OBJCOPY = $(AVR_TOOLS_PATH)/avr-objcopy
+OBJDUMP = $(AVR_TOOLS_PATH)/avr-objdump
+AR = $(AVR_TOOLS_PATH)/avr-ar
+SIZE = $(AVR_TOOLS_PATH)/avr-size
+NM = $(AVR_TOOLS_PATH)/avr-nm
+AVRDUDE = $(AVR_TOOLS_PATH)/avrdude
+REMOVE = rm -f
+MV = mv -f
+
+# Define all object files.
+OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
+
+# Define all listing files.
+LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
+
+# Combine all necessary flags and optional flags.
+# Add target processor to flags.
+ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
+ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
+ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
+
+
+# Default target.
+all: applet_files build sizeafter
+
+build: elf hex
+
+applet_files: $(TARGET).pde
+ # Here is the "preprocessing".
+ # It creates a .cpp file based with the same name as the .pde file.
+ # On top of the new .cpp file comes the WProgram.h header.
+ # At the end there is a generic main() function attached.
+ # Then the .cpp file will be compiled. Errors during compile will
+ # refer to this new, automatically generated, file.
+ # Not the original .pde file you actually edit...
+ test -d applet || mkdir applet
+ echo '#include "WProgram.h"' > applet/$(TARGET).cpp
+ cat $(TARGET).pde >> applet/$(TARGET).cpp
+ cat $(ARDUINO)/main.cxx >> applet/$(TARGET).cpp
+
+elf: applet/$(TARGET).elf
+hex: applet/$(TARGET).hex
+eep: applet/$(TARGET).eep
+lss: applet/$(TARGET).lss
+sym: applet/$(TARGET).sym
+
+# Program the device.
+upload: applet/$(TARGET).hex
+ $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
+
+
+ # Display size of file.
+HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex
+ELFSIZE = $(SIZE) applet/$(TARGET).elf
+sizebefore:
+ @if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi
+
+sizeafter:
+ @if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi
+
+
+# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
+COFFCONVERT=$(OBJCOPY) --debugging \
+--change-section-address .data-0x800000 \
+--change-section-address .bss-0x800000 \
+--change-section-address .noinit-0x800000 \
+--change-section-address .eeprom-0x810000
+
+
+coff: applet/$(TARGET).elf
+ $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof
+
+
+extcoff: $(TARGET).elf
+ $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof
+
+
+.SUFFIXES: .elf .hex .eep .lss .sym
+
+.elf.hex:
+ $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
+
+.elf.eep:
+ -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
+ --change-section-lma .eeprom=0 -O $(FORMAT) $< $@
+
+# Create extended listing file from ELF output file.
+.elf.lss:
+ $(OBJDUMP) -h -S $< > $@
+
+# Create a symbol table from ELF output file.
+.elf.sym:
+ $(NM) -n $< > $@
+
+ # Link: create ELF output file from library.
+applet/$(TARGET).elf: $(TARGET).pde applet/core.a
+ $(CC) $(ALL_CFLAGS) -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
+
+applet/core.a: $(OBJ)
+ @for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
+
+
+
+# Compile: create object files from C++ source files.
+.cpp.o:
+ $(CXX) -c $(ALL_CXXFLAGS) $< -o $@
+
+# Compile: create object files from C source files.
+.c.o:
+ $(CC) -c $(ALL_CFLAGS) $< -o $@
+
+
+# Compile: create assembler files from C source files.
+.c.s:
+ $(CC) -S $(ALL_CFLAGS) $< -o $@
+
+
+# Assemble: create object files from assembler source files.
+.S.o:
+ $(CC) -c $(ALL_ASFLAGS) $< -o $@
+
+
+
+# Target: clean project.
+clean:
+ $(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \
+ applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \
+ $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
+
+depend:
+ if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
+ then \
+ sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
+ $(MAKEFILE).$$$$ && \
+ $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
+ fi
+ echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
+ >> $(MAKEFILE); \
+ $(CC) -M -mmcu=$(MCU) $(CDEFS) $(CINCS) $(SRC) $(ASRC) >> $(MAKEFILE)
+
+.PHONY: all build elf hex eep lss sym program coff extcoff clean depend applet_files sizebefore sizeafter
diff --git a/Marlin/Gen7/cores/arduino/Print.cpp b/Marlin/Gen7/cores/arduino/Print.cpp
new file mode 100644
index 00000000000..d4833da7cb1
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/Print.cpp
@@ -0,0 +1,203 @@
+/*
+ Print.cpp - Base class that provides print() and println()
+ Copyright (c) 2008 David A. Mellis. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+
+ Modified 23 November 2006 by David A. Mellis
+ */
+
+#include <stdio.h>
+#include <string.h>
+#include <inttypes.h>
+#include <math.h>
+#include "wiring.h"
+
+#include "Print.h"
+
+// Public Methods //////////////////////////////////////////////////////////////
+
+void Print::print(uint8_t b)
+{
+ this->write(b);
+}
+
+void Print::print(char c)
+{
+ print((byte) c);
+}
+
+void Print::print(const char c[])
+{
+ while (*c)
+ print(*c++);
+}
+
+void Print::print(int n)
+{
+ print((long) n);
+}
+
+void Print::print(unsigned int n)
+{
+ print((unsigned long) n);
+}
+
+void Print::print(long n)
+{
+ if (n < 0) {
+ print('-');
+ n = -n;
+ }
+ printNumber(n, 10);
+}
+
+void Print::print(unsigned long n)
+{
+ printNumber(n, 10);
+}
+
+void Print::print(long n, int base)
+{
+ if (base == 0)
+ print((char) n);
+ else if (base == 10)
+ print(n);
+ else
+ printNumber(n, base);
+}
+
+void Print::print(double n)
+{
+ printFloat(n, 2);
+}
+
+void Print::println(void)
+{
+ print('\r');
+ print('\n');
+}
+
+void Print::println(char c)
+{
+ print(c);
+ println();
+}
+
+void Print::println(const char c[])
+{
+ print(c);
+ println();
+}
+
+void Print::println(uint8_t b)
+{
+ print(b);
+ println();
+}
+
+void Print::println(int n)
+{
+ print(n);
+ println();
+}
+
+void Print::println(unsigned int n)
+{
+ print(n);
+ println();
+}
+
+void Print::println(long n)
+{
+ print(n);
+ println();
+}
+
+void Print::println(unsigned long n)
+{
+ print(n);
+ println();
+}
+
+void Print::println(long n, int base)
+{
+ print(n, base);
+ println();
+}
+
+void Print::println(double n)
+{
+ print(n);
+ println();
+}
+
+// Private Methods /////////////////////////////////////////////////////////////
+
+void Print::printNumber(unsigned long n, uint8_t base)
+{
+ unsigned char buf[8 * sizeof(long)]; // Assumes 8-bit chars.
+ unsigned long i = 0;
+
+ if (n == 0) {
+ print('0');
+ return;
+ }
+
+ while (n > 0) {
+ buf[i++] = n % base;
+ n /= base;
+ }
+
+ for (; i > 0; i--)
+ print((char) (buf[i - 1] < 10 ?
+ '0' + buf[i - 1] :
+ 'A' + buf[i - 1] - 10));
+}
+
+void Print::printFloat(double number, uint8_t digits)
+{
+ // Handle negative numbers
+ if (number < 0.0)
+ {
+ print('-');
+ number = -number;
+ }
+
+ // Round correctly so that print(1.999, 2) prints as "2.00"
+ double rounding = 0.5;
+ for (uint8_t i=0; i<digits; ++i)
+ rounding /= 10.0;
+
+ number += rounding;
+
+ // Extract the integer part of the number and print it
+ unsigned long int_part = (unsigned long)number;
+ double remainder = number - (double)int_part;
+ print(int_part);
+
+ // Print the decimal point, but only if there are digits beyond
+ if (digits > 0)
+ print(".");
+
+ // Extract digits from the remainder one at a time
+ while (digits-- > 0)
+ {
+ remainder *= 10.0;
+ int toPrint = int(remainder);
+ print(toPrint);
+ remainder -= toPrint;
+ }
+}
diff --git a/Marlin/Gen7/cores/arduino/Print.h b/Marlin/Gen7/cores/arduino/Print.h
new file mode 100644
index 00000000000..c95a0dc094f
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/Print.h
@@ -0,0 +1,59 @@
+/*
+ Print.h - Base class that provides print() and println()
+ Copyright (c) 2008 David A. Mellis. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
+#ifndef Print_h
+#define Print_h
+
+#include <inttypes.h>
+
+#define DEC 10
+#define HEX 16
+#define OCT 8
+#define BIN 2
+#define BYTE 0
+
+class Print
+{
+ private:
+ void printNumber(unsigned long, uint8_t);
+ void printFloat(double, uint8_t);
+ public:
+ virtual void write(uint8_t);
+ void print(char);
+ void print(const char[]);
+ void print(uint8_t);
+ void print(int);
+ void print(unsigned int);
+ void print(long);
+ void print(unsigned long);
+ void print(long, int);
+ void print(double);
+ void println(void);
+ void println(char);
+ void println(const char[]);
+ void println(uint8_t);
+ void println(int);
+ void println(unsigned int);
+ void println(long);
+ void println(unsigned long);
+ void println(long, int);
+ void println(double);
+};
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/Tone.cpp b/Marlin/Gen7/cores/arduino/Tone.cpp
new file mode 100644
index 00000000000..827fe49ef42
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/Tone.cpp
@@ -0,0 +1,515 @@
+/* Tone.cpp
+
+ A Tone Generator Library
+
+ Written by Brett Hagman
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+
+Version Modified By Date Comments
+------- ----------- -------- --------
+0001 B Hagman 09/08/02 Initial coding
+0002 B Hagman 09/08/18 Multiple pins
+0003 B Hagman 09/08/18 Moved initialization from constructor to begin()
+0004 B Hagman 09/09/26 Fixed problems with ATmega8
+0005 B Hagman 09/11/23 Scanned prescalars for best fit on 8 bit timers
+ 09/11/25 Changed pin toggle method to XOR
+ 09/11/25 Fixed timer0 from being excluded
+0006 D Mellis 09/12/29 Replaced objects with functions
+
+*************************************************/
+
+#include <avr/interrupt.h>
+#include <avr/pgmspace.h>
+#include <wiring.h>
+#include <pins_arduino.h>
+
+#if defined(__AVR_ATmega8__)
+#define TCCR2A TCCR2
+#define TCCR2B TCCR2
+#define COM2A1 COM21
+#define COM2A0 COM20
+#define OCR2A OCR2
+#define TIMSK2 TIMSK
+#define OCIE2A OCIE2
+#define TIMER2_COMPA_vect TIMER2_COMP_vect
+#define TIMSK1 TIMSK
+#endif
+
+// timerx_toggle_count:
+// > 0 - duration specified
+// = 0 - stopped
+// < 0 - infinitely (until stop() method called, or new play() called)
+
+#if !defined(__AVR_ATmega8__)
+volatile long timer0_toggle_count;
+volatile uint8_t *timer0_pin_port;
+volatile uint8_t timer0_pin_mask;
+#endif
+
+volatile long timer1_toggle_count;
+volatile uint8_t *timer1_pin_port;
+volatile uint8_t timer1_pin_mask;
+volatile long timer2_toggle_count;
+volatile uint8_t *timer2_pin_port;
+volatile uint8_t timer2_pin_mask;
+
+#if defined(__AVR_ATmega1280__)
+volatile long timer3_toggle_count;
+volatile uint8_t *timer3_pin_port;
+volatile uint8_t timer3_pin_mask;
+volatile long timer4_toggle_count;
+volatile uint8_t *timer4_pin_port;
+volatile uint8_t timer4_pin_mask;
+volatile long timer5_toggle_count;
+volatile uint8_t *timer5_pin_port;
+volatile uint8_t timer5_pin_mask;
+#endif
+
+
+#if defined(__AVR_ATmega1280__)
+
+#define AVAILABLE_TONE_PINS 1
+
+const uint8_t PROGMEM tone_pin_to_timer_PGM[] = { 2 /*, 3, 4, 5, 1, 0 */ };
+static uint8_t tone_pins[AVAILABLE_TONE_PINS] = { 255 /*, 255, 255, 255, 255, 255 */ };
+
+#elif defined(__AVR_ATmega8__)
+
+#define AVAILABLE_TONE_PINS 1
+
+const uint8_t PROGMEM tone_pin_to_timer_PGM[] = { 2 /*, 1 */ };
+static uint8_t tone_pins[AVAILABLE_TONE_PINS] = { 255 /*, 255 */ };
+
+#else
+
+#define AVAILABLE_TONE_PINS 1
+
+// Leave timer 0 to last.
+const uint8_t PROGMEM tone_pin_to_timer_PGM[] = { 2 /*, 1, 0 */ };
+static uint8_t tone_pins[AVAILABLE_TONE_PINS] = { 255 /*, 255, 255 */ };
+
+#endif
+
+
+
+static int8_t toneBegin(uint8_t _pin)
+{
+ int8_t _timer = -1;
+
+ // if we're already using the pin, the timer should be configured.
+ for (int i = 0; i < AVAILABLE_TONE_PINS; i++) {
+ if (tone_pins[i] == _pin) {
+ return pgm_read_byte(tone_pin_to_timer_PGM + i);
+ }
+ }
+
+ // search for an unused timer.
+ for (int i = 0; i < AVAILABLE_TONE_PINS; i++) {
+ if (tone_pins[i] == 255) {
+ tone_pins[i] = _pin;
+ _timer = pgm_read_byte(tone_pin_to_timer_PGM + i);
+ break;
+ }
+ }
+
+ if (_timer != -1)
+ {
+ // Set timer specific stuff
+ // All timers in CTC mode
+ // 8 bit timers will require changing prescalar values,
+ // whereas 16 bit timers are set to either ck/1 or ck/64 prescalar
+ switch (_timer)
+ {
+#if !defined(__AVR_ATmega8__)
+ case 0:
+ // 8 bit timer
+ TCCR0A = 0;
+ TCCR0B = 0;
+ bitWrite(TCCR0A, WGM01, 1);
+ bitWrite(TCCR0B, CS00, 1);
+ timer0_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer0_pin_mask = digitalPinToBitMask(_pin);
+ break;
+#endif
+
+ case 1:
+ // 16 bit timer
+ TCCR1A = 0;
+ TCCR1B = 0;
+ bitWrite(TCCR1B, WGM12, 1);
+ bitWrite(TCCR1B, CS10, 1);
+ timer1_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer1_pin_mask = digitalPinToBitMask(_pin);
+ break;
+ case 2:
+ // 8 bit timer
+ TCCR2A = 0;
+ TCCR2B = 0;
+ bitWrite(TCCR2A, WGM21, 1);
+ bitWrite(TCCR2B, CS20, 1);
+ timer2_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer2_pin_mask = digitalPinToBitMask(_pin);
+ break;
+
+#if defined(__AVR_ATmega1280__)
+ case 3:
+ // 16 bit timer
+ TCCR3A = 0;
+ TCCR3B = 0;
+ bitWrite(TCCR3B, WGM32, 1);
+ bitWrite(TCCR3B, CS30, 1);
+ timer3_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer3_pin_mask = digitalPinToBitMask(_pin);
+ break;
+ case 4:
+ // 16 bit timer
+ TCCR4A = 0;
+ TCCR4B = 0;
+ bitWrite(TCCR4B, WGM42, 1);
+ bitWrite(TCCR4B, CS40, 1);
+ timer4_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer4_pin_mask = digitalPinToBitMask(_pin);
+ break;
+ case 5:
+ // 16 bit timer
+ TCCR5A = 0;
+ TCCR5B = 0;
+ bitWrite(TCCR5B, WGM52, 1);
+ bitWrite(TCCR5B, CS50, 1);
+ timer5_pin_port = portOutputRegister(digitalPinToPort(_pin));
+ timer5_pin_mask = digitalPinToBitMask(_pin);
+ break;
+#endif
+ }
+ }
+
+ return _timer;
+}
+
+
+
+// frequency (in hertz) and duration (in milliseconds).
+
+void tone(uint8_t _pin, unsigned int frequency, unsigned long duration)
+{
+ uint8_t prescalarbits = 0b001;
+ long toggle_count = 0;
+ uint32_t ocr = 0;
+ int8_t _timer;
+
+ _timer = toneBegin(_pin);
+
+ if (_timer >= 0)
+ {
+ // Set the pinMode as OUTPUT
+ pinMode(_pin, OUTPUT);
+
+ // if we are using an 8 bit timer, scan through prescalars to find the best fit
+ if (_timer == 0 || _timer == 2)
+ {
+ ocr = F_CPU / frequency / 2 - 1;
+ prescalarbits = 0b001; // ck/1: same for both timers
+ if (ocr > 255)
+ {
+ ocr = F_CPU / frequency / 2 / 8 - 1;
+ prescalarbits = 0b010; // ck/8: same for both timers
+
+ if (_timer == 2 && ocr > 255)
+ {
+ ocr = F_CPU / frequency / 2 / 32 - 1;
+ prescalarbits = 0b011;
+ }
+
+ if (ocr > 255)
+ {
+ ocr = F_CPU / frequency / 2 / 64 - 1;
+ prescalarbits = _timer == 0 ? 0b011 : 0b100;
+
+ if (_timer == 2 && ocr > 255)
+ {
+ ocr = F_CPU / frequency / 2 / 128 - 1;
+ prescalarbits = 0b101;
+ }
+
+ if (ocr > 255)
+ {
+ ocr = F_CPU / frequency / 2 / 256 - 1;
+ prescalarbits = _timer == 0 ? 0b100 : 0b110;
+ if (ocr > 255)
+ {
+ // can't do any better than /1024
+ ocr = F_CPU / frequency / 2 / 1024 - 1;
+ prescalarbits = _timer == 0 ? 0b101 : 0b111;
+ }
+ }
+ }
+ }
+
+#if !defined(__AVR_ATmega8__)
+ if (_timer == 0)
+ TCCR0B = prescalarbits;
+ else
+#endif
+ TCCR2B = prescalarbits;
+ }
+ else
+ {
+ // two choices for the 16 bit timers: ck/1 or ck/64
+ ocr = F_CPU / frequency / 2 - 1;
+
+ prescalarbits = 0b001;
+ if (ocr > 0xffff)
+ {
+ ocr = F_CPU / frequency / 2 / 64 - 1;
+ prescalarbits = 0b011;
+ }
+
+ if (_timer == 1)
+ TCCR1B = (TCCR1B & 0b11111000) | prescalarbits;
+#if defined(__AVR_ATmega1280__)
+ else if (_timer == 3)
+ TCCR3B = (TCCR3B & 0b11111000) | prescalarbits;
+ else if (_timer == 4)
+ TCCR4B = (TCCR4B & 0b11111000) | prescalarbits;
+ else if (_timer == 5)
+ TCCR5B = (TCCR5B & 0b11111000) | prescalarbits;
+#endif
+
+ }
+
+
+ // Calculate the toggle count
+ if (duration > 0)
+ {
+ toggle_count = 2 * frequency * duration / 1000;
+ }
+ else
+ {
+ toggle_count = -1;
+ }
+
+ // Set the OCR for the given timer,
+ // set the toggle count,
+ // then turn on the interrupts
+ switch (_timer)
+ {
+
+#if !defined(__AVR_ATmega8__)
+ case 0:
+ OCR0A = ocr;
+ timer0_toggle_count = toggle_count;
+ bitWrite(TIMSK0, OCIE0A, 1);
+ break;
+#endif
+
+ case 1:
+ OCR1A = ocr;
+ timer1_toggle_count = toggle_count;
+ bitWrite(TIMSK1, OCIE1A, 1);
+ break;
+ case 2:
+ OCR2A = ocr;
+ timer2_toggle_count = toggle_count;
+ bitWrite(TIMSK2, OCIE2A, 1);
+ break;
+
+#if defined(__AVR_ATmega1280__)
+ case 3:
+ OCR3A = ocr;
+ timer3_toggle_count = toggle_count;
+ bitWrite(TIMSK3, OCIE3A, 1);
+ break;
+ case 4:
+ OCR4A = ocr;
+ timer4_toggle_count = toggle_count;
+ bitWrite(TIMSK4, OCIE4A, 1);
+ break;
+ case 5:
+ OCR5A = ocr;
+ timer5_toggle_count = toggle_count;
+ bitWrite(TIMSK5, OCIE5A, 1);
+ break;
+#endif
+
+ }
+ }
+}
+
+
+void noTone(uint8_t _pin)
+{
+ int8_t _timer = -1;
+
+ for (int i = 0; i < AVAILABLE_TONE_PINS; i++) {
+ if (tone_pins[i] == _pin) {
+ _timer = pgm_read_byte(tone_pin_to_timer_PGM + i);
+ tone_pins[i] = 255;
+ }
+ }
+
+ switch (_timer)
+ {
+#if defined(__AVR_ATmega8__)
+ case 1:
+ bitWrite(TIMSK1, OCIE1A, 0);
+ break;
+ case 2:
+ bitWrite(TIMSK2, OCIE2A, 0);
+ break;
+
+#else
+ case 0:
+ TIMSK0 = 0;
+ break;
+ case 1:
+ TIMSK1 = 0;
+ break;
+ case 2:
+ TIMSK2 = 0;
+ break;
+#endif
+
+#if defined(__AVR_ATmega1280__)
+ case 3:
+ TIMSK3 = 0;
+ break;
+ case 4:
+ TIMSK4 = 0;
+ break;
+ case 5:
+ TIMSK5 = 0;
+ break;
+#endif
+ }
+
+ digitalWrite(_pin, 0);
+}
+
+#if 0
+#if !defined(__AVR_ATmega8__)
+ISR(TIMER0_COMPA_vect)
+{
+ if (timer0_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer0_pin_port ^= timer0_pin_mask;
+
+ if (timer0_toggle_count > 0)
+ timer0_toggle_count--;
+ }
+ else
+ {
+ TIMSK0 = 0; // disable the interrupt
+ *timer0_pin_port &= ~(timer0_pin_mask); // keep pin low after stop
+ }
+}
+#endif
+
+
+ISR(TIMER1_COMPA_vect)
+{
+ if (timer1_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer1_pin_port ^= timer1_pin_mask;
+
+ if (timer1_toggle_count > 0)
+ timer1_toggle_count--;
+ }
+ else
+ {
+ TIMSK1 = 0; // disable the interrupt
+ *timer1_pin_port &= ~(timer1_pin_mask); // keep pin low after stop
+ }
+}
+#endif
+
+
+ISR(TIMER2_COMPA_vect)
+{
+
+ if (timer2_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer2_pin_port ^= timer2_pin_mask;
+
+ if (timer2_toggle_count > 0)
+ timer2_toggle_count--;
+ }
+ else
+ {
+ TIMSK2 = 0; // disable the interrupt
+ *timer2_pin_port &= ~(timer2_pin_mask); // keep pin low after stop
+ }
+}
+
+
+
+//#if defined(__AVR_ATmega1280__)
+#if 0
+
+ISR(TIMER3_COMPA_vect)
+{
+ if (timer3_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer3_pin_port ^= timer3_pin_mask;
+
+ if (timer3_toggle_count > 0)
+ timer3_toggle_count--;
+ }
+ else
+ {
+ TIMSK3 = 0; // disable the interrupt
+ *timer3_pin_port &= ~(timer3_pin_mask); // keep pin low after stop
+ }
+}
+
+ISR(TIMER4_COMPA_vect)
+{
+ if (timer4_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer4_pin_port ^= timer4_pin_mask;
+
+ if (timer4_toggle_count > 0)
+ timer4_toggle_count--;
+ }
+ else
+ {
+ TIMSK4 = 0; // disable the interrupt
+ *timer4_pin_port &= ~(timer4_pin_mask); // keep pin low after stop
+ }
+}
+
+ISR(TIMER5_COMPA_vect)
+{
+ if (timer5_toggle_count != 0)
+ {
+ // toggle the pin
+ *timer5_pin_port ^= timer5_pin_mask;
+
+ if (timer5_toggle_count > 0)
+ timer5_toggle_count--;
+ }
+ else
+ {
+ TIMSK5 = 0; // disable the interrupt
+ *timer5_pin_port &= ~(timer5_pin_mask); // keep pin low after stop
+ }
+}
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/WCharacter.h b/Marlin/Gen7/cores/arduino/WCharacter.h
new file mode 100644
index 00000000000..79733b50a53
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WCharacter.h
@@ -0,0 +1,168 @@
+/*
+ WCharacter.h - Character utility functions for Wiring & Arduino
+ Copyright (c) 2010 Hernando Barragan. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef Character_h
+#define Character_h
+
+#include <ctype.h>
+
+// WCharacter.h prototypes
+inline boolean isAlphaNumeric(int c) __attribute__((always_inline));
+inline boolean isAlpha(int c) __attribute__((always_inline));
+inline boolean isAscii(int c) __attribute__((always_inline));
+inline boolean isWhitespace(int c) __attribute__((always_inline));
+inline boolean isControl(int c) __attribute__((always_inline));
+inline boolean isDigit(int c) __attribute__((always_inline));
+inline boolean isGraph(int c) __attribute__((always_inline));
+inline boolean isLowerCase(int c) __attribute__((always_inline));
+inline boolean isPrintable(int c) __attribute__((always_inline));
+inline boolean isPunct(int c) __attribute__((always_inline));
+inline boolean isSpace(int c) __attribute__((always_inline));
+inline boolean isUpperCase(int c) __attribute__((always_inline));
+inline boolean isHexadecimalDigit(int c) __attribute__((always_inline));
+inline int toAscii(int c) __attribute__((always_inline));
+inline int toLowerCase(int c) __attribute__((always_inline));
+inline int toUpperCase(int c)__attribute__((always_inline));
+
+
+// Checks for an alphanumeric character.
+// It is equivalent to (isalpha(c) || isdigit(c)).
+inline boolean isAlphaNumeric(int c)
+{
+ return ( isalnum(c) == 0 ? false : true);
+}
+
+
+// Checks for an alphabetic character.
+// It is equivalent to (isupper(c) || islower(c)).
+inline boolean isAlpha(int c)
+{
+ return ( isalpha(c) == 0 ? false : true);
+}
+
+
+// Checks whether c is a 7-bit unsigned char value
+// that fits into the ASCII character set.
+inline boolean isAscii(int c)
+{
+ return ( isascii (c) == 0 ? false : true);
+}
+
+
+// Checks for a blank character, that is, a space or a tab.
+inline boolean isWhitespace(int c)
+{
+ return ( isblank (c) == 0 ? false : true);
+}
+
+
+// Checks for a control character.
+inline boolean isControl(int c)
+{
+ return ( iscntrl (c) == 0 ? false : true);
+}
+
+
+// Checks for a digit (0 through 9).
+inline boolean isDigit(int c)
+{
+ return ( isdigit (c) == 0 ? false : true);
+}
+
+
+// Checks for any printable character except space.
+inline boolean isGraph(int c)
+{
+ return ( isgraph (c) == 0 ? false : true);
+}
+
+
+// Checks for a lower-case character.
+inline boolean isLowerCase(int c)
+{
+ return (islower (c) == 0 ? false : true);
+}
+
+
+// Checks for any printable character including space.
+inline boolean isPrintable(int c)
+{
+ return ( isprint (c) == 0 ? false : true);
+}
+
+
+// Checks for any printable character which is not a space
+// or an alphanumeric character.
+inline boolean isPunct(int c)
+{
+ return ( ispunct (c) == 0 ? false : true);
+}
+
+
+// Checks for white-space characters. For the avr-libc library,
+// these are: space, formfeed ('\f'), newline ('\n'), carriage
+// return ('\r'), horizontal tab ('\t'), and vertical tab ('\v').
+inline boolean isSpace(int c)
+{
+ return ( isspace (c) == 0 ? false : true);
+}
+
+
+// Checks for an uppercase letter.
+inline boolean isUpperCase(int c)
+{
+ return ( isupper (c) == 0 ? false : true);
+}
+
+
+// Checks for a hexadecimal digits, i.e. one of 0 1 2 3 4 5 6 7
+// 8 9 a b c d e f A B C D E F.
+inline boolean isHexadecimalDigit(int c)
+{
+ return ( isxdigit (c) == 0 ? false : true);
+}
+
+
+// Converts c to a 7-bit unsigned char value that fits into the
+// ASCII character set, by clearing the high-order bits.
+inline int toAscii(int c)
+{
+ return toascii (c);
+}
+
+
+// Warning:
+// Many people will be unhappy if you use this function.
+// This function will convert accented letters into random
+// characters.
+
+// Converts the letter c to lower case, if possible.
+inline int toLowerCase(int c)
+{
+ return tolower (c);
+}
+
+
+// Converts the letter c to upper case, if possible.
+inline int toUpperCase(int c)
+{
+ return toupper (c);
+}
+
+#endif
\ No newline at end of file
diff --git a/Marlin/Gen7/cores/arduino/WConstants.h b/Marlin/Gen7/cores/arduino/WConstants.h
new file mode 100644
index 00000000000..3e19ac44aac
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WConstants.h
@@ -0,0 +1 @@
+#include "wiring.h"
diff --git a/Marlin/Gen7/cores/arduino/WInterrupts.c b/Marlin/Gen7/cores/arduino/WInterrupts.c
new file mode 100644
index 00000000000..6f3f0b130a4
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WInterrupts.c
@@ -0,0 +1,87 @@
+/* -*- mode: jde; c-basic-offset: 2; indent-tabs-mode: nil -*- */
+
+/*
+ Part of the Wiring project - http://wiring.uniandes.edu.co
+
+ Copyright (c) 2004-05 Hernando Barragan
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ Modified 24 November 2006 by David A. Mellis
+*/
+
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <avr/pgmspace.h>
+#include <stdio.h>
+
+#include "WConstants.h"
+#include "wiring_private.h"
+
+volatile static voidFuncPtr intFunc[EXTERNAL_NUM_INTERRUPTS];
+// volatile static voidFuncPtr twiIntFunc;
+
+void attachInterrupt(uint8_t interruptNum, void (*userFunc)(void), int mode)
+{
+ if(interruptNum < EXTERNAL_NUM_INTERRUPTS)
+ {
+ intFunc[interruptNum] = userFunc;
+
+ //clear the config for the change settings
+ EICRA &= ~(B00000011 << (interruptNum * 2));
+
+ //set our mode.
+ EICRA |= (mode << (interruptNum * 2));
+
+ // Enable the interrupt.
+ EIMSK |= (1 << interruptNum);
+ }
+}
+
+void detachInterrupt(uint8_t interruptNum)
+{
+ if(interruptNum < EXTERNAL_NUM_INTERRUPTS)
+ {
+ // Disable the interrupt.
+ EIMSK &= ~(1 << interruptNum);
+
+ intFunc[interruptNum] = 0;
+ }
+}
+
+ISR(INT0_vect) {
+ if(intFunc[EXTERNAL_INT_0])
+ intFunc[EXTERNAL_INT_0]();
+}
+
+ISR(INT1_vect) {
+ if(intFunc[EXTERNAL_INT_1])
+ intFunc[EXTERNAL_INT_1]();
+}
+
+ISR(INT2_vect) {
+ if(intFunc[EXTERNAL_INT_2])
+ intFunc[EXTERNAL_INT_2]();
+}
+
+/*
+SIGNAL(SIG_2WIRE_SERIAL) {
+ if(twiIntFunc)
+ twiIntFunc();
+}
+*/
+
diff --git a/Marlin/Gen7/cores/arduino/WMath.cpp b/Marlin/Gen7/cores/arduino/WMath.cpp
new file mode 100644
index 00000000000..7a230f542f0
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WMath.cpp
@@ -0,0 +1,60 @@
+/* -*- mode: jde; c-basic-offset: 2; indent-tabs-mode: nil -*- */
+
+/*
+ Part of the Wiring project - http://wiring.org.co
+ Copyright (c) 2004-06 Hernando Barragan
+ Modified 13 August 2006, David A. Mellis for Arduino - http://www.arduino.cc/
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id$
+*/
+
+extern "C" {
+ #include "stdlib.h"
+}
+
+void randomSeed(unsigned int seed)
+{
+ if (seed != 0){
+ srandom(seed);
+ }
+}
+
+long random(long howbig)
+{
+ if (howbig == 0) {
+ return 0;
+ }
+ return random() % howbig;
+}
+
+long random(long howsmall, long howbig)
+{
+ if (howsmall >= howbig) {
+ return howsmall;
+ }
+ long diff = howbig - howsmall;
+ return random(diff) + howsmall;
+}
+
+long map(long x, long in_min, long in_max, long out_min, long out_max)
+{
+ return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
+}
+
+unsigned int makeWord(unsigned int w) { return w; }
+unsigned int makeWord(unsigned char h, unsigned char l) { return (h << 8) | l; }
diff --git a/Marlin/Gen7/cores/arduino/WProgram.h b/Marlin/Gen7/cores/arduino/WProgram.h
new file mode 100644
index 00000000000..2c7ed16d89b
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WProgram.h
@@ -0,0 +1,34 @@
+#ifndef WProgram_h
+#define WProgram_h
+
+#include <stdlib.h>
+#include <string.h>
+#include <math.h>
+
+#include <avr/interrupt.h>
+
+#include "wiring.h"
+
+#ifdef __cplusplus
+#include "WCharacter.h"
+#include "WString.h"
+#include "HardwareSerial.h"
+
+uint16_t makeWord(uint16_t w);
+uint16_t makeWord(byte h, byte l);
+
+#define word(...) makeWord(__VA_ARGS__)
+
+unsigned long pulseIn(uint8_t pin, uint8_t state, unsigned long timeout = 1000000L);
+
+void tone(uint8_t _pin, unsigned int frequency, unsigned long duration = 0);
+void noTone(uint8_t _pin);
+
+// WMath prototypes
+long random(long);
+long random(long, long);
+void randomSeed(unsigned int);
+long map(long, long, long, long, long);
+#endif
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/WString.cpp b/Marlin/Gen7/cores/arduino/WString.cpp
new file mode 100644
index 00000000000..db5a441dc27
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WString.cpp
@@ -0,0 +1,443 @@
+/*
+ WString.cpp - String library for Wiring & Arduino
+ Copyright (c) 2009-10 Hernando Barragan. All rights reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
+#include <stdlib.h>
+#include "WProgram.h"
+#include "WString.h"
+
+
+String::String( const char *value )
+{
+ if ( value == NULL )
+ value = "";
+ getBuffer( _length = strlen( value ) );
+ if ( _buffer != NULL )
+ strcpy( _buffer, value );
+}
+
+String::String( const String &value )
+{
+ getBuffer( _length = value._length );
+ if ( _buffer != NULL )
+ strcpy( _buffer, value._buffer );
+}
+
+String::String( const char value )
+{
+ _length = 1;
+ getBuffer(1);
+ if ( _buffer != NULL ) {
+ _buffer[0] = value;
+ _buffer[1] = 0;
+ }
+}
+
+String::String( const unsigned char value )
+{
+ _length = 1;
+ getBuffer(1);
+ if ( _buffer != NULL) {
+ _buffer[0] = value;
+ _buffer[1] = 0;
+ }
+}
+
+String::String( const int value, const int base )
+{
+ char buf[33];
+ itoa((signed long)value, buf, base);
+ getBuffer( _length = strlen(buf) );
+ if ( _buffer != NULL )
+ strcpy( _buffer, buf );
+}
+
+String::String( const unsigned int value, const int base )
+{
+ char buf[33];
+ ultoa((unsigned long)value, buf, base);
+ getBuffer( _length = strlen(buf) );
+ if ( _buffer != NULL )
+ strcpy( _buffer, buf );
+}
+
+String::String( const long value, const int base )
+{
+ char buf[33];
+ ltoa(value, buf, base);
+ getBuffer( _length = strlen(buf) );
+ if ( _buffer != NULL )
+ strcpy( _buffer, buf );
+}
+
+String::String( const unsigned long value, const int base )
+{
+ char buf[33];
+ ultoa(value, buf, 10);
+ getBuffer( _length = strlen(buf) );
+ if ( _buffer != NULL )
+ strcpy( _buffer, buf );
+}
+
+char String::charAt( unsigned int loc ) const
+{
+ return operator[]( loc );
+}
+
+void String::setCharAt( unsigned int loc, const char aChar )
+{
+ if(_buffer == NULL) return;
+ if(_length > loc) {
+ _buffer[loc] = aChar;
+ }
+}
+
+int String::compareTo( const String &s2 ) const
+{
+ return strcmp( _buffer, s2._buffer );
+}
+
+const String & String::concat( const String &s2 )
+{
+ return (*this) += s2;
+}
+
+const String & String::operator=( const String &rhs )
+{
+ if ( this == &rhs )
+ return *this;
+
+ if ( rhs._length > _length )
+ {
+ free(_buffer);
+ getBuffer( rhs._length );
+ }
+
+ if ( _buffer != NULL ) {
+ _length = rhs._length;
+ strcpy( _buffer, rhs._buffer );
+ }
+ return *this;
+}
+
+//const String & String::operator+=( const char aChar )
+//{
+// if ( _length == _capacity )
+// doubleBuffer();
+//
+// _buffer[ _length++ ] = aChar;
+// _buffer[ _length ] = '\0';
+// return *this;
+//}
+
+const String & String::operator+=( const String &other )
+{
+ _length += other._length;
+ if ( _length > _capacity )
+ {
+ char *temp = (char *)realloc(_buffer, _length + 1);
+ if ( temp != NULL ) {
+ _buffer = temp;
+ _capacity = _length;
+ } else {
+ _length -= other._length;
+ return *this;
+ }
+ }
+ strcat( _buffer, other._buffer );
+ return *this;
+}
+
+
+int String::operator==( const String &rhs ) const
+{
+ return ( _length == rhs._length && strcmp( _buffer, rhs._buffer ) == 0 );
+}
+
+int String::operator!=( const String &rhs ) const
+{
+ return ( _length != rhs.length() || strcmp( _buffer, rhs._buffer ) != 0 );
+}
+
+int String::operator<( const String &rhs ) const
+{
+ return strcmp( _buffer, rhs._buffer ) < 0;
+}
+
+int String::operator>( const String &rhs ) const
+{
+ return strcmp( _buffer, rhs._buffer ) > 0;
+}
+
+int String::operator<=( const String &rhs ) const
+{
+ return strcmp( _buffer, rhs._buffer ) <= 0;
+}
+
+int String::operator>=( const String & rhs ) const
+{
+ return strcmp( _buffer, rhs._buffer ) >= 0;
+}
+
+char & String::operator[]( unsigned int index )
+{
+ static char dummy_writable_char;
+ if (index >= _length || !_buffer) {
+ dummy_writable_char = 0;
+ return dummy_writable_char;
+ }
+ return _buffer[ index ];
+}
+
+char String::operator[]( unsigned int index ) const
+{
+ // need to check for valid index, to do later
+ return _buffer[ index ];
+}
+
+boolean String::endsWith( const String &s2 ) const
+{
+ if ( _length < s2._length )
+ return 0;
+
+ return strcmp( &_buffer[ _length - s2._length], s2._buffer ) == 0;
+}
+
+boolean String::equals( const String &s2 ) const
+{
+ return ( _length == s2._length && strcmp( _buffer,s2._buffer ) == 0 );
+}
+
+boolean String::equalsIgnoreCase( const String &s2 ) const
+{
+ if ( this == &s2 )
+ return true; //1;
+ else if ( _length != s2._length )
+ return false; //0;
+
+ return strcmp(toLowerCase()._buffer, s2.toLowerCase()._buffer) == 0;
+}
+
+String String::replace( char findChar, char replaceChar )
+{
+ if ( _buffer == NULL ) return *this;
+ String theReturn = _buffer;
+ char* temp = theReturn._buffer;
+ while( (temp = strchr( temp, findChar )) != 0 )
+ *temp = replaceChar;
+
+ return theReturn;
+}
+
+String String::replace( const String& match, const String& replace )
+{
+ if ( _buffer == NULL ) return *this;
+ String temp = _buffer, newString;
+
+ int loc;
+ while ( (loc = temp.indexOf( match )) != -1 )
+ {
+ newString += temp.substring( 0, loc );
+ newString += replace;
+ temp = temp.substring( loc + match._length );
+ }
+ newString += temp;
+ return newString;
+}
+
+int String::indexOf( char temp ) const
+{
+ return indexOf( temp, 0 );
+}
+
+int String::indexOf( char ch, unsigned int fromIndex ) const
+{
+ if ( fromIndex >= _length )
+ return -1;
+
+ const char* temp = strchr( &_buffer[fromIndex], ch );
+ if ( temp == NULL )
+ return -1;
+
+ return temp - _buffer;
+}
+
+int String::indexOf( const String &s2 ) const
+{
+ return indexOf( s2, 0 );
+}
+
+int String::indexOf( const String &s2, unsigned int fromIndex ) const
+{
+ if ( fromIndex >= _length )
+ return -1;
+
+ const char *theFind = strstr( &_buffer[ fromIndex ], s2._buffer );
+
+ if ( theFind == NULL )
+ return -1;
+
+ return theFind - _buffer; // pointer subtraction
+}
+
+int String::lastIndexOf( char theChar ) const
+{
+ return lastIndexOf( theChar, _length - 1 );
+}
+
+int String::lastIndexOf( char ch, unsigned int fromIndex ) const
+{
+ if ( fromIndex >= _length )
+ return -1;
+
+ char tempchar = _buffer[fromIndex + 1];
+ _buffer[fromIndex + 1] = '\0';
+ char* temp = strrchr( _buffer, ch );
+ _buffer[fromIndex + 1] = tempchar;
+
+ if ( temp == NULL )
+ return -1;
+
+ return temp - _buffer;
+}
+
+int String::lastIndexOf( const String &s2 ) const
+{
+ return lastIndexOf( s2, _length - s2._length );
+}
+
+int String::lastIndexOf( const String &s2, unsigned int fromIndex ) const
+{
+ // check for empty strings
+ if ( s2._length == 0 || s2._length - 1 > fromIndex || fromIndex >= _length )
+ return -1;
+
+ // matching first character
+ char temp = s2[ 0 ];
+
+ for ( int i = fromIndex; i >= 0; i-- )
+ {
+ if ( _buffer[ i ] == temp && (*this).substring( i, i + s2._length ).equals( s2 ) )
+ return i;
+ }
+ return -1;
+}
+
+boolean String::startsWith( const String &s2 ) const
+{
+ if ( _length < s2._length )
+ return 0;
+
+ return startsWith( s2, 0 );
+}
+
+boolean String::startsWith( const String &s2, unsigned int offset ) const
+{
+ if ( offset > _length - s2._length )
+ return 0;
+
+ return strncmp( &_buffer[offset], s2._buffer, s2._length ) == 0;
+}
+
+String String::substring( unsigned int left ) const
+{
+ return substring( left, _length );
+}
+
+String String::substring( unsigned int left, unsigned int right ) const
+{
+ if ( left > right )
+ {
+ int temp = right;
+ right = left;
+ left = temp;
+ }
+
+ if ( right > _length )
+ {
+ right = _length;
+ }
+
+ char temp = _buffer[ right ]; // save the replaced character
+ _buffer[ right ] = '\0';
+ String outPut = ( _buffer + left ); // pointer arithmetic
+ _buffer[ right ] = temp; //restore character
+ return outPut;
+}
+
+String String::toLowerCase() const
+{
+ String temp = _buffer;
+
+ for ( unsigned int i = 0; i < _length; i++ )
+ temp._buffer[ i ] = (char)tolower( temp._buffer[ i ] );
+ return temp;
+}
+
+String String::toUpperCase() const
+{
+ String temp = _buffer;
+
+ for ( unsigned int i = 0; i < _length; i++ )
+ temp._buffer[ i ] = (char)toupper( temp._buffer[ i ] );
+ return temp;
+}
+
+String String::trim() const
+{
+ if ( _buffer == NULL ) return *this;
+ String temp = _buffer;
+ unsigned int i,j;
+
+ for ( i = 0; i < _length; i++ )
+ {
+ if ( !isspace(_buffer[i]) )
+ break;
+ }
+
+ for ( j = temp._length - 1; j > i; j-- )
+ {
+ if ( !isspace(_buffer[j]) )
+ break;
+ }
+
+ return temp.substring( i, j + 1);
+}
+
+void String::getBytes(unsigned char *buf, unsigned int bufsize)
+{
+ if (!bufsize || !buf) return;
+ unsigned int len = bufsize - 1;
+ if (len > _length) len = _length;
+ strncpy((char *)buf, _buffer, len);
+ buf[len] = 0;
+}
+
+void String::toCharArray(char *buf, unsigned int bufsize)
+{
+ if (!bufsize || !buf) return;
+ unsigned int len = bufsize - 1;
+ if (len > _length) len = _length;
+ strncpy(buf, _buffer, len);
+ buf[len] = 0;
+}
+
+
+long String::toInt() {
+ return atol(_buffer);
+}
diff --git a/Marlin/Gen7/cores/arduino/WString.h b/Marlin/Gen7/cores/arduino/WString.h
new file mode 100644
index 00000000000..cadddb9476f
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/WString.h
@@ -0,0 +1,112 @@
+/*
+ WString.h - String library for Wiring & Arduino
+ Copyright (c) 2009-10 Hernando Barragan. All right reserved.
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
+#ifndef String_h
+#define String_h
+
+//#include "WProgram.h"
+#include <stdlib.h>
+#include <string.h>
+#include <ctype.h>
+
+class String
+{
+ public:
+ // constructors
+ String( const char *value = "" );
+ String( const String &value );
+ String( const char );
+ String( const unsigned char );
+ String( const int, const int base=10);
+ String( const unsigned int, const int base=10 );
+ String( const long, const int base=10 );
+ String( const unsigned long, const int base=10 );
+ ~String() { free(_buffer); _length = _capacity = 0;} //added _length = _capacity = 0;
+
+ // operators
+ const String & operator = ( const String &rhs );
+ const String & operator +=( const String &rhs );
+ //const String & operator +=( const char );
+ int operator ==( const String &rhs ) const;
+ int operator !=( const String &rhs ) const;
+ int operator < ( const String &rhs ) const;
+ int operator > ( const String &rhs ) const;
+ int operator <=( const String &rhs ) const;
+ int operator >=( const String &rhs ) const;
+ char operator []( unsigned int index ) const;
+ char& operator []( unsigned int index );
+ //operator const char *() const { return _buffer; }
+
+ // general methods
+ char charAt( unsigned int index ) const;
+ int compareTo( const String &anotherString ) const;
+ unsigned char endsWith( const String &suffix ) const;
+ unsigned char equals( const String &anObject ) const;
+ unsigned char equalsIgnoreCase( const String &anotherString ) const;
+ int indexOf( char ch ) const;
+ int indexOf( char ch, unsigned int fromIndex ) const;
+ int indexOf( const String &str ) const;
+ int indexOf( const String &str, unsigned int fromIndex ) const;
+ int lastIndexOf( char ch ) const;
+ int lastIndexOf( char ch, unsigned int fromIndex ) const;
+ int lastIndexOf( const String &str ) const;
+ int lastIndexOf( const String &str, unsigned int fromIndex ) const;
+ const unsigned int length( ) const { return _length; }
+ void setCharAt(unsigned int index, const char ch);
+ unsigned char startsWith( const String &prefix ) const;
+ unsigned char startsWith( const String &prefix, unsigned int toffset ) const;
+ String substring( unsigned int beginIndex ) const;
+ String substring( unsigned int beginIndex, unsigned int endIndex ) const;
+ String toLowerCase( ) const;
+ String toUpperCase( ) const;
+ String trim( ) const;
+ void getBytes(unsigned char *buf, unsigned int bufsize);
+ void toCharArray(char *buf, unsigned int bufsize);
+ long toInt( );
+ const String& concat( const String &str );
+ String replace( char oldChar, char newChar );
+ String replace( const String& match, const String& replace );
+ friend String operator + ( String lhs, const String &rhs );
+
+ protected:
+ char *_buffer; // the actual char array
+ unsigned int _capacity; // the array length minus one (for the '\0')
+ unsigned int _length; // the String length (not counting the '\0')
+
+ void getBuffer(unsigned int maxStrLen);
+
+ private:
+
+};
+
+// allocate buffer space
+inline void String::getBuffer(unsigned int maxStrLen)
+{
+ _capacity = maxStrLen;
+ _buffer = (char *) malloc(_capacity + 1);
+ if (_buffer == NULL) _length = _capacity = 0;
+}
+
+inline String operator+( String lhs, const String &rhs )
+{
+ return lhs += rhs;
+}
+
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/binary.h b/Marlin/Gen7/cores/arduino/binary.h
new file mode 100644
index 00000000000..af1498033ab
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/binary.h
@@ -0,0 +1,515 @@
+#ifndef Binary_h
+#define Binary_h
+
+#define B0 0
+#define B00 0
+#define B000 0
+#define B0000 0
+#define B00000 0
+#define B000000 0
+#define B0000000 0
+#define B00000000 0
+#define B1 1
+#define B01 1
+#define B001 1
+#define B0001 1
+#define B00001 1
+#define B000001 1
+#define B0000001 1
+#define B00000001 1
+#define B10 2
+#define B010 2
+#define B0010 2
+#define B00010 2
+#define B000010 2
+#define B0000010 2
+#define B00000010 2
+#define B11 3
+#define B011 3
+#define B0011 3
+#define B00011 3
+#define B000011 3
+#define B0000011 3
+#define B00000011 3
+#define B100 4
+#define B0100 4
+#define B00100 4
+#define B000100 4
+#define B0000100 4
+#define B00000100 4
+#define B101 5
+#define B0101 5
+#define B00101 5
+#define B000101 5
+#define B0000101 5
+#define B00000101 5
+#define B110 6
+#define B0110 6
+#define B00110 6
+#define B000110 6
+#define B0000110 6
+#define B00000110 6
+#define B111 7
+#define B0111 7
+#define B00111 7
+#define B000111 7
+#define B0000111 7
+#define B00000111 7
+#define B1000 8
+#define B01000 8
+#define B001000 8
+#define B0001000 8
+#define B00001000 8
+#define B1001 9
+#define B01001 9
+#define B001001 9
+#define B0001001 9
+#define B00001001 9
+#define B1010 10
+#define B01010 10
+#define B001010 10
+#define B0001010 10
+#define B00001010 10
+#define B1011 11
+#define B01011 11
+#define B001011 11
+#define B0001011 11
+#define B00001011 11
+#define B1100 12
+#define B01100 12
+#define B001100 12
+#define B0001100 12
+#define B00001100 12
+#define B1101 13
+#define B01101 13
+#define B001101 13
+#define B0001101 13
+#define B00001101 13
+#define B1110 14
+#define B01110 14
+#define B001110 14
+#define B0001110 14
+#define B00001110 14
+#define B1111 15
+#define B01111 15
+#define B001111 15
+#define B0001111 15
+#define B00001111 15
+#define B10000 16
+#define B010000 16
+#define B0010000 16
+#define B00010000 16
+#define B10001 17
+#define B010001 17
+#define B0010001 17
+#define B00010001 17
+#define B10010 18
+#define B010010 18
+#define B0010010 18
+#define B00010010 18
+#define B10011 19
+#define B010011 19
+#define B0010011 19
+#define B00010011 19
+#define B10100 20
+#define B010100 20
+#define B0010100 20
+#define B00010100 20
+#define B10101 21
+#define B010101 21
+#define B0010101 21
+#define B00010101 21
+#define B10110 22
+#define B010110 22
+#define B0010110 22
+#define B00010110 22
+#define B10111 23
+#define B010111 23
+#define B0010111 23
+#define B00010111 23
+#define B11000 24
+#define B011000 24
+#define B0011000 24
+#define B00011000 24
+#define B11001 25
+#define B011001 25
+#define B0011001 25
+#define B00011001 25
+#define B11010 26
+#define B011010 26
+#define B0011010 26
+#define B00011010 26
+#define B11011 27
+#define B011011 27
+#define B0011011 27
+#define B00011011 27
+#define B11100 28
+#define B011100 28
+#define B0011100 28
+#define B00011100 28
+#define B11101 29
+#define B011101 29
+#define B0011101 29
+#define B00011101 29
+#define B11110 30
+#define B011110 30
+#define B0011110 30
+#define B00011110 30
+#define B11111 31
+#define B011111 31
+#define B0011111 31
+#define B00011111 31
+#define B100000 32
+#define B0100000 32
+#define B00100000 32
+#define B100001 33
+#define B0100001 33
+#define B00100001 33
+#define B100010 34
+#define B0100010 34
+#define B00100010 34
+#define B100011 35
+#define B0100011 35
+#define B00100011 35
+#define B100100 36
+#define B0100100 36
+#define B00100100 36
+#define B100101 37
+#define B0100101 37
+#define B00100101 37
+#define B100110 38
+#define B0100110 38
+#define B00100110 38
+#define B100111 39
+#define B0100111 39
+#define B00100111 39
+#define B101000 40
+#define B0101000 40
+#define B00101000 40
+#define B101001 41
+#define B0101001 41
+#define B00101001 41
+#define B101010 42
+#define B0101010 42
+#define B00101010 42
+#define B101011 43
+#define B0101011 43
+#define B00101011 43
+#define B101100 44
+#define B0101100 44
+#define B00101100 44
+#define B101101 45
+#define B0101101 45
+#define B00101101 45
+#define B101110 46
+#define B0101110 46
+#define B00101110 46
+#define B101111 47
+#define B0101111 47
+#define B00101111 47
+#define B110000 48
+#define B0110000 48
+#define B00110000 48
+#define B110001 49
+#define B0110001 49
+#define B00110001 49
+#define B110010 50
+#define B0110010 50
+#define B00110010 50
+#define B110011 51
+#define B0110011 51
+#define B00110011 51
+#define B110100 52
+#define B0110100 52
+#define B00110100 52
+#define B110101 53
+#define B0110101 53
+#define B00110101 53
+#define B110110 54
+#define B0110110 54
+#define B00110110 54
+#define B110111 55
+#define B0110111 55
+#define B00110111 55
+#define B111000 56
+#define B0111000 56
+#define B00111000 56
+#define B111001 57
+#define B0111001 57
+#define B00111001 57
+#define B111010 58
+#define B0111010 58
+#define B00111010 58
+#define B111011 59
+#define B0111011 59
+#define B00111011 59
+#define B111100 60
+#define B0111100 60
+#define B00111100 60
+#define B111101 61
+#define B0111101 61
+#define B00111101 61
+#define B111110 62
+#define B0111110 62
+#define B00111110 62
+#define B111111 63
+#define B0111111 63
+#define B00111111 63
+#define B1000000 64
+#define B01000000 64
+#define B1000001 65
+#define B01000001 65
+#define B1000010 66
+#define B01000010 66
+#define B1000011 67
+#define B01000011 67
+#define B1000100 68
+#define B01000100 68
+#define B1000101 69
+#define B01000101 69
+#define B1000110 70
+#define B01000110 70
+#define B1000111 71
+#define B01000111 71
+#define B1001000 72
+#define B01001000 72
+#define B1001001 73
+#define B01001001 73
+#define B1001010 74
+#define B01001010 74
+#define B1001011 75
+#define B01001011 75
+#define B1001100 76
+#define B01001100 76
+#define B1001101 77
+#define B01001101 77
+#define B1001110 78
+#define B01001110 78
+#define B1001111 79
+#define B01001111 79
+#define B1010000 80
+#define B01010000 80
+#define B1010001 81
+#define B01010001 81
+#define B1010010 82
+#define B01010010 82
+#define B1010011 83
+#define B01010011 83
+#define B1010100 84
+#define B01010100 84
+#define B1010101 85
+#define B01010101 85
+#define B1010110 86
+#define B01010110 86
+#define B1010111 87
+#define B01010111 87
+#define B1011000 88
+#define B01011000 88
+#define B1011001 89
+#define B01011001 89
+#define B1011010 90
+#define B01011010 90
+#define B1011011 91
+#define B01011011 91
+#define B1011100 92
+#define B01011100 92
+#define B1011101 93
+#define B01011101 93
+#define B1011110 94
+#define B01011110 94
+#define B1011111 95
+#define B01011111 95
+#define B1100000 96
+#define B01100000 96
+#define B1100001 97
+#define B01100001 97
+#define B1100010 98
+#define B01100010 98
+#define B1100011 99
+#define B01100011 99
+#define B1100100 100
+#define B01100100 100
+#define B1100101 101
+#define B01100101 101
+#define B1100110 102
+#define B01100110 102
+#define B1100111 103
+#define B01100111 103
+#define B1101000 104
+#define B01101000 104
+#define B1101001 105
+#define B01101001 105
+#define B1101010 106
+#define B01101010 106
+#define B1101011 107
+#define B01101011 107
+#define B1101100 108
+#define B01101100 108
+#define B1101101 109
+#define B01101101 109
+#define B1101110 110
+#define B01101110 110
+#define B1101111 111
+#define B01101111 111
+#define B1110000 112
+#define B01110000 112
+#define B1110001 113
+#define B01110001 113
+#define B1110010 114
+#define B01110010 114
+#define B1110011 115
+#define B01110011 115
+#define B1110100 116
+#define B01110100 116
+#define B1110101 117
+#define B01110101 117
+#define B1110110 118
+#define B01110110 118
+#define B1110111 119
+#define B01110111 119
+#define B1111000 120
+#define B01111000 120
+#define B1111001 121
+#define B01111001 121
+#define B1111010 122
+#define B01111010 122
+#define B1111011 123
+#define B01111011 123
+#define B1111100 124
+#define B01111100 124
+#define B1111101 125
+#define B01111101 125
+#define B1111110 126
+#define B01111110 126
+#define B1111111 127
+#define B01111111 127
+#define B10000000 128
+#define B10000001 129
+#define B10000010 130
+#define B10000011 131
+#define B10000100 132
+#define B10000101 133
+#define B10000110 134
+#define B10000111 135
+#define B10001000 136
+#define B10001001 137
+#define B10001010 138
+#define B10001011 139
+#define B10001100 140
+#define B10001101 141
+#define B10001110 142
+#define B10001111 143
+#define B10010000 144
+#define B10010001 145
+#define B10010010 146
+#define B10010011 147
+#define B10010100 148
+#define B10010101 149
+#define B10010110 150
+#define B10010111 151
+#define B10011000 152
+#define B10011001 153
+#define B10011010 154
+#define B10011011 155
+#define B10011100 156
+#define B10011101 157
+#define B10011110 158
+#define B10011111 159
+#define B10100000 160
+#define B10100001 161
+#define B10100010 162
+#define B10100011 163
+#define B10100100 164
+#define B10100101 165
+#define B10100110 166
+#define B10100111 167
+#define B10101000 168
+#define B10101001 169
+#define B10101010 170
+#define B10101011 171
+#define B10101100 172
+#define B10101101 173
+#define B10101110 174
+#define B10101111 175
+#define B10110000 176
+#define B10110001 177
+#define B10110010 178
+#define B10110011 179
+#define B10110100 180
+#define B10110101 181
+#define B10110110 182
+#define B10110111 183
+#define B10111000 184
+#define B10111001 185
+#define B10111010 186
+#define B10111011 187
+#define B10111100 188
+#define B10111101 189
+#define B10111110 190
+#define B10111111 191
+#define B11000000 192
+#define B11000001 193
+#define B11000010 194
+#define B11000011 195
+#define B11000100 196
+#define B11000101 197
+#define B11000110 198
+#define B11000111 199
+#define B11001000 200
+#define B11001001 201
+#define B11001010 202
+#define B11001011 203
+#define B11001100 204
+#define B11001101 205
+#define B11001110 206
+#define B11001111 207
+#define B11010000 208
+#define B11010001 209
+#define B11010010 210
+#define B11010011 211
+#define B11010100 212
+#define B11010101 213
+#define B11010110 214
+#define B11010111 215
+#define B11011000 216
+#define B11011001 217
+#define B11011010 218
+#define B11011011 219
+#define B11011100 220
+#define B11011101 221
+#define B11011110 222
+#define B11011111 223
+#define B11100000 224
+#define B11100001 225
+#define B11100010 226
+#define B11100011 227
+#define B11100100 228
+#define B11100101 229
+#define B11100110 230
+#define B11100111 231
+#define B11101000 232
+#define B11101001 233
+#define B11101010 234
+#define B11101011 235
+#define B11101100 236
+#define B11101101 237
+#define B11101110 238
+#define B11101111 239
+#define B11110000 240
+#define B11110001 241
+#define B11110010 242
+#define B11110011 243
+#define B11110100 244
+#define B11110101 245
+#define B11110110 246
+#define B11110111 247
+#define B11111000 248
+#define B11111001 249
+#define B11111010 250
+#define B11111011 251
+#define B11111100 252
+#define B11111101 253
+#define B11111110 254
+#define B11111111 255
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/main.cpp b/Marlin/Gen7/cores/arduino/main.cpp
new file mode 100644
index 00000000000..cc6e81d906c
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/main.cpp
@@ -0,0 +1,14 @@
+#include <WProgram.h>
+
+int main(void)
+{
+ init();
+
+ setup();
+
+ for (;;)
+ loop();
+
+ return 0;
+}
+
diff --git a/Marlin/Gen7/cores/arduino/main.cxx b/Marlin/Gen7/cores/arduino/main.cxx
new file mode 100644
index 00000000000..52351e4c98b
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/main.cxx
@@ -0,0 +1,12 @@
+int main(void)
+{
+ init();
+
+ setup();
+
+ for (;;)
+ loop();
+
+ return 0;
+}
+
diff --git a/Marlin/Gen7/cores/arduino/pins_arduino.c b/Marlin/Gen7/cores/arduino/pins_arduino.c
new file mode 100644
index 00000000000..ccb88fe989e
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/pins_arduino.c
@@ -0,0 +1,200 @@
+/*
+ pins_arduino.c - pin definitions for the Arduino board
+ Part of Arduino / Wiring Lite
+
+ Copyright (c) 2005 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: pins_arduino.c 254 2007-04-20 23:17:38Z mellis $
+*/
+
+#include <avr/io.h>
+#include "wiring_private.h"
+#include "pins_arduino.h"
+
+// On the Sanguino board, digital pins are also used
+// for the analog output (software PWM). Analog input
+// pins are a separate set.
+
+// ATMEL ATMEGA644P / SANGUINO
+//
+// +---\/---+
+// INT0 (D 0) PB0 1| |40 PA0 (AI 0 / D31)
+// INT1 (D 1) PB1 2| |39 PA1 (AI 1 / D30)
+// INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
+// PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
+// PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
+// MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
+// MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
+// SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
+// RST 9| |32 AREF
+// VCC 10| |31 GND
+// GND 11| |30 AVCC
+// XTAL2 12| |29 PC7 (D 23)
+// XTAL1 13| |28 PC6 (D 22)
+// RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
+// TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
+// RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
+// TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
+// PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
+// PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
+// PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
+// +--------+
+//
+
+#define PA 1
+#define PB 2
+#define PC 3
+#define PD 4
+
+// these arrays map port names (e.g. port B) to the
+// appropriate addresses for various functions (e.g. reading
+// and writing)
+const uint8_t PROGMEM port_to_mode_PGM[] =
+{
+ NOT_A_PORT,
+ &DDRA,
+ &DDRB,
+ &DDRC,
+ &DDRD,
+};
+
+const uint8_t PROGMEM port_to_output_PGM[] =
+{
+ NOT_A_PORT,
+ &PORTA,
+ &PORTB,
+ &PORTC,
+ &PORTD,
+};
+
+const uint8_t PROGMEM port_to_input_PGM[] =
+{
+ NOT_A_PORT,
+ &PINA,
+ &PINB,
+ &PINC,
+ &PIND,
+};
+
+const uint8_t PROGMEM digital_pin_to_port_PGM[] =
+{
+ PB, /* 0 */
+ PB,
+ PB,
+ PB,
+ PB,
+ PB,
+ PB,
+ PB,
+ PD, /* 8 */
+ PD,
+ PD,
+ PD,
+ PD,
+ PD,
+ PD,
+ PD,
+ PC, /* 16 */
+ PC,
+ PC,
+ PC,
+ PC,
+ PC,
+ PC,
+ PC,
+ PA, /* 24 */
+ PA,
+ PA,
+ PA,
+ PA,
+ PA,
+ PA,
+ PA /* 31 */
+};
+
+const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] =
+{
+ _BV(0), /* 0, port B */
+ _BV(1),
+ _BV(2),
+ _BV(3),
+ _BV(4),
+ _BV(5),
+ _BV(6),
+ _BV(7),
+ _BV(0), /* 8, port D */
+ _BV(1),
+ _BV(2),
+ _BV(3),
+ _BV(4),
+ _BV(5),
+ _BV(6),
+ _BV(7),
+ _BV(0), /* 16, port C */
+ _BV(1),
+ _BV(2),
+ _BV(3),
+ _BV(4),
+ _BV(5),
+ _BV(6),
+ _BV(7),
+ _BV(7), /* 24, port A */
+ _BV(6),
+ _BV(5),
+ _BV(4),
+ _BV(3),
+ _BV(2),
+ _BV(1),
+ _BV(0)
+};
+
+const uint8_t PROGMEM digital_pin_to_timer_PGM[] =
+{
+ NOT_ON_TIMER, /* 0 - PB0 */
+ NOT_ON_TIMER, /* 1 - PB1 */
+ NOT_ON_TIMER, /* 2 - PB2 */
+ TIMER0A, /* 3 - PB3 */
+ TIMER0B, /* 4 - PB4 */
+ NOT_ON_TIMER, /* 5 - PB5 */
+ NOT_ON_TIMER, /* 6 - PB6 */
+ NOT_ON_TIMER, /* 7 - PB7 */
+ NOT_ON_TIMER, /* 8 - PD0 */
+ NOT_ON_TIMER, /* 9 - PD1 */
+ NOT_ON_TIMER, /* 10 - PD2 */
+ NOT_ON_TIMER, /* 11 - PD3 */
+ TIMER1B, /* 12 - PD4 */
+ TIMER1A, /* 13 - PD5 */
+ TIMER2B, /* 14 - PD6 */
+ TIMER2A, /* 15 - PD7 */
+ NOT_ON_TIMER, /* 16 - PC0 */
+ NOT_ON_TIMER, /* 17 - PC1 */
+ NOT_ON_TIMER, /* 18 - PC2 */
+ NOT_ON_TIMER, /* 19 - PC3 */
+ NOT_ON_TIMER, /* 20 - PC4 */
+ NOT_ON_TIMER, /* 21 - PC5 */
+ NOT_ON_TIMER, /* 22 - PC6 */
+ NOT_ON_TIMER, /* 23 - PC7 */
+ NOT_ON_TIMER, /* 24 - PA0 */
+ NOT_ON_TIMER, /* 25 - PA1 */
+ NOT_ON_TIMER, /* 26 - PA2 */
+ NOT_ON_TIMER, /* 27 - PA3 */
+ NOT_ON_TIMER, /* 28 - PA4 */
+ NOT_ON_TIMER, /* 29 - PA5 */
+ NOT_ON_TIMER, /* 30 - PA6 */
+ NOT_ON_TIMER /* 31 - PA7 */
+};
diff --git a/Marlin/Gen7/cores/arduino/pins_arduino.h b/Marlin/Gen7/cores/arduino/pins_arduino.h
new file mode 100644
index 00000000000..e0b7add867b
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/pins_arduino.h
@@ -0,0 +1,65 @@
+/*
+ pins_arduino.h - Pin definition functions for Arduino
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2007 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.h 249 2007-02-03 16:52:51Z mellis $
+*/
+
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <avr/pgmspace.h>
+
+#define NOT_A_PIN 0
+#define NOT_A_PORT 0
+
+#define NOT_ON_TIMER 0
+#define TIMER0A 1
+#define TIMER0B 2
+#define TIMER1A 3
+#define TIMER1B 4
+#define TIMER2 5
+#define TIMER2A 6
+#define TIMER2B 7
+
+extern const uint8_t PROGMEM port_to_mode_PGM[];
+extern const uint8_t PROGMEM port_to_input_PGM[];
+extern const uint8_t PROGMEM port_to_output_PGM[];
+
+extern const uint8_t PROGMEM digital_pin_to_port_PGM[];
+extern const uint8_t PROGMEM digital_pin_to_bit_PGM[];
+extern const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[];
+
+extern const uint8_t PROGMEM digital_pin_to_timer_PGM[];
+
+// Get the bit location within the hardware port of the given virtual pin.
+// This comes from the pins_*.c file for the active board configuration.
+//
+// These perform slightly better as macros compared to inline functions
+//
+#define digitalPinToPort(P) ( pgm_read_byte( digital_pin_to_port_PGM + (P) ) )
+#define digitalPinToBitMask(P) ( pgm_read_byte( digital_pin_to_bit_mask_PGM + (P) ) )
+#define digitalPinToTimer(P) ( pgm_read_byte( digital_pin_to_timer_PGM + (P) ) )
+#define analogInPinToBit(P) (P)
+#define portOutputRegister(P) ( (volatile uint8_t *)( pgm_read_byte( port_to_output_PGM + (P))) )
+#define portInputRegister(P) ( (volatile uint8_t *)( pgm_read_byte( port_to_input_PGM + (P))) )
+#define portModeRegister(P) ( (volatile uint8_t *)( pgm_read_byte( port_to_mode_PGM + (P))) )
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/wiring.c b/Marlin/Gen7/cores/arduino/wiring.c
new file mode 100644
index 00000000000..1a102ae0f69
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring.c
@@ -0,0 +1,203 @@
+/*
+ wiring.c - Partial implementation of the Wiring API for the ATmega8.
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 388 2008-03-08 22:05:23Z mellis $
+*/
+
+#include "wiring_private.h"
+
+volatile unsigned long timer0_overflow_count = 0;
+volatile unsigned long timer0_clock_cycles = 0;
+volatile unsigned long timer0_millis = 0;
+
+SIGNAL(TIMER0_OVF_vect)
+{
+ timer0_overflow_count++;
+ // timer 0 prescale factor is 64 and the timer overflows at 256
+ timer0_clock_cycles += 64UL * 256UL;
+ while (timer0_clock_cycles > clockCyclesPerMicrosecond() * 1000UL) {
+ timer0_clock_cycles -= clockCyclesPerMicrosecond() * 1000UL;
+ timer0_millis++;
+ }
+}
+
+unsigned long millis()
+{
+ unsigned long m;
+ uint8_t oldSREG = SREG;
+
+ // disable interrupts while we read timer0_millis or we might get an
+ // inconsistent value (e.g. in the middle of the timer0_millis++)
+ cli();
+ m = timer0_millis;
+ SREG = oldSREG;
+
+ return m;
+}
+
+unsigned long micros() {
+ unsigned long m, t;
+ uint8_t oldSREG = SREG;
+
+ cli();
+ t = TCNT0;
+
+#ifdef TIFR0
+ if ((TIFR0 & _BV(TOV0)) && (t == 0))
+ t = 256;
+#else
+ if ((TIFR & _BV(TOV0)) && (t == 0))
+ t = 256;
+#endif
+
+ m = timer0_overflow_count;
+ SREG = oldSREG;
+
+ return ((m << 8) + t) * (64 / clockCyclesPerMicrosecond());
+}
+
+void delay(unsigned long ms)
+{
+ unsigned long start = millis();
+
+ while (millis() - start <= ms)
+ ;
+}
+
+/* Delay for the given number of microseconds. Assumes a 8 or 16 MHz clock.
+ * Disables interrupts, which will disrupt the millis() function if used
+ * too frequently. */
+void delayMicroseconds(unsigned int us)
+{
+ uint8_t oldSREG;
+
+ // calling avrlib's delay_us() function with low values (e.g. 1 or
+ // 2 microseconds) gives delays longer than desired.
+ //delay_us(us);
+
+#if F_CPU >= 16000000L
+ // for the 16 MHz clock on most Arduino boards
+
+ // for a one-microsecond delay, simply return. the overhead
+ // of the function call yields a delay of approximately 1 1/8 us.
+ if (--us == 0)
+ return;
+
+ // the following loop takes a quarter of a microsecond (4 cycles)
+ // per iteration, so execute it four times for each microsecond of
+ // delay requested.
+ us <<= 2;
+
+ // account for the time taken in the preceeding commands.
+ us -= 2;
+#else
+ // for the 8 MHz internal clock on the ATmega168
+
+ // for a one- or two-microsecond delay, simply return. the overhead of
+ // the function calls takes more than two microseconds. can't just
+ // subtract two, since us is unsigned; we'd overflow.
+ if (--us == 0)
+ return;
+ if (--us == 0)
+ return;
+
+ // the following loop takes half of a microsecond (4 cycles)
+ // per iteration, so execute it twice for each microsecond of
+ // delay requested.
+ us <<= 1;
+
+ // partially compensate for the time taken by the preceeding commands.
+ // we can't subtract any more than this or we'd overflow w/ small delays.
+ us--;
+#endif
+
+ // disable interrupts, otherwise the timer 0 overflow interrupt that
+ // tracks milliseconds will make us delay longer than we want.
+ oldSREG = SREG;
+ cli();
+
+ // busy wait
+ __asm__ __volatile__ (
+ "1: sbiw %0,1" "\n\t" // 2 cycles
+ "brne 1b" : "=w" (us) : "0" (us) // 2 cycles
+ );
+
+ // reenable interrupts.
+ SREG = oldSREG;
+}
+
+void init()
+{
+ // this needs to be called before setup() or some functions won't
+ // work there
+ sei();
+
+ // on the ATmega168, timer 0 is also used for fast hardware pwm
+ // (using phase-correct PWM would mean that timer 0 overflowed half as often
+ // resulting in different millis() behavior on the ATmega8 and ATmega168)
+ sbi(TCCR0A, WGM01);
+ sbi(TCCR0A, WGM00);
+
+ // set timer 0 prescale factor to 64
+ sbi(TCCR0B, CS01);
+ sbi(TCCR0B, CS00);
+
+ // enable timer 0 overflow interrupt
+ sbi(TIMSK0, TOIE0);
+
+ // timers 1 and 2 are used for phase-correct hardware pwm
+ // this is better for motors as it ensures an even waveform
+ // note, however, that fast pwm mode can achieve a frequency of up
+ // 8 MHz (with a 16 MHz clock) at 50% duty cycle
+
+ // set timer 1 prescale factor to 64
+ sbi(TCCR1B, CS11);
+ sbi(TCCR1B, CS10);
+
+ // put timer 1 in 8-bit phase correct pwm mode
+ sbi(TCCR1A, WGM10);
+
+ // set timer 2 prescale factor to 64
+ sbi(TCCR2B, CS22);
+
+ // configure timer 2 for phase correct pwm (8-bit)
+ sbi(TCCR2A, WGM20);
+
+ // set a2d prescale factor to 128
+ // 16 MHz / 128 = 125 KHz, inside the desired 50-200 KHz range.
+ // XXX: this will not work properly for other clock speeds, and
+ // this code should use F_CPU to determine the prescale factor.
+ sbi(ADCSRA, ADPS2);
+ sbi(ADCSRA, ADPS1);
+ sbi(ADCSRA, ADPS0);
+
+ // enable a2d conversions
+ sbi(ADCSRA, ADEN);
+
+ // the bootloader connects pins 0 and 1 to the USART; disconnect them
+ // here so they can be used as normal digital i/o; they will be
+ // reconnected in Serial.begin()
+ UCSR0B = 0;
+ #if defined(__AVR_ATmega644P__)
+ //TODO: test to see if disabling this helps?
+ //UCSR1B = 0;
+ #endif
+}
diff --git a/Marlin/Gen7/cores/arduino/wiring.h b/Marlin/Gen7/cores/arduino/wiring.h
new file mode 100644
index 00000000000..6309a364fca
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring.h
@@ -0,0 +1,133 @@
+/*
+ wiring.h - Partial implementation of the Wiring API for the ATmega8.
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.h 387 2008-03-08 21:30:00Z mellis $
+*/
+
+#ifndef Wiring_h
+#define Wiring_h
+
+#include <avr/io.h>
+#include "binary.h"
+
+#ifdef __cplusplus
+extern "C"{
+#endif
+
+#define HIGH 0x1
+#define LOW 0x0
+
+#define INPUT 0x0
+#define OUTPUT 0x1
+
+#define true 0x1
+#define false 0x0
+
+#define PI 3.14159265
+#define HALF_PI 1.57079
+#define TWO_PI 6.283185
+#define DEG_TO_RAD 0.01745329
+#define RAD_TO_DEG 57.2957786
+
+#define SERIAL 0x0
+#define DISPLAY 0x1
+
+#define LSBFIRST 0
+#define MSBFIRST 1
+
+#define CHANGE 1
+#define FALLING 2
+#define RISING 3
+
+#define INTERNAL 3
+#define DEFAULT 1
+#define EXTERNAL 0
+
+// undefine stdlib's abs if encountered
+#ifdef abs
+#undef abs
+#endif
+
+#define min(a,b) ((a)<(b)?(a):(b))
+#define max(a,b) ((a)>(b)?(a):(b))
+#define abs(x) ((x)>0?(x):-(x))
+#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))
+#define round(x) ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
+#define radians(deg) ((deg)*DEG_TO_RAD)
+#define degrees(rad) ((rad)*RAD_TO_DEG)
+#define sq(x) ((x)*(x))
+
+#define interrupts() sei()
+#define noInterrupts() cli()
+
+#define clockCyclesPerMicrosecond() ( F_CPU / 1000000L )
+#define clockCyclesToMicroseconds(a) ( (a) / clockCyclesPerMicrosecond() )
+#define microsecondsToClockCycles(a) ( (a) * clockCyclesPerMicrosecond() )
+
+#define lowByte(w) ((w) & 0xff)
+#define highByte(w) ((w) >> 8)
+
+#define bitRead(value, bit) (((value) >> (bit)) & 0x01)
+#define bitSet(value, bit) ((value) |= (1UL << (bit)))
+#define bitClear(value, bit) ((value) &= ~(1UL << (bit)))
+#define bitWrite(value, bit, bitvalue) (bitvalue ? bitSet(value, bit) : bitClear(value, bit))
+
+typedef unsigned int word;
+
+#define bit(b) (1 << (b))
+
+typedef uint8_t boolean;
+typedef uint8_t byte;
+
+void init(void);
+
+void pinMode(uint8_t, uint8_t);
+void digitalWrite(uint8_t, uint8_t);
+int digitalRead(uint8_t);
+int analogRead(uint8_t);
+void analogReference(uint8_t mode);
+void analogWrite(uint8_t, int);
+
+void beginSerial(uint8_t, long);
+void serialWrite(uint8_t, unsigned char);
+int serialAvailable(uint8_t);
+int serialRead(uint8_t);
+void serialFlush(uint8_t);
+
+unsigned long millis(void);
+unsigned long micros(void);
+void delay(unsigned long);
+void delayMicroseconds(unsigned int us);
+unsigned long pulseIn(uint8_t pin, uint8_t state, unsigned long timeout);
+
+void shiftOut(uint8_t dataPin, uint8_t clockPin, uint8_t bitOrder, byte val);
+
+void attachInterrupt(uint8_t, void (*)(void), int mode);
+void detachInterrupt(uint8_t);
+
+void setup(void);
+void loop(void);
+
+#ifdef __cplusplus
+} // extern "C"
+#endif
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/wiring_analog.c b/Marlin/Gen7/cores/arduino/wiring_analog.c
new file mode 100644
index 00000000000..b98bb1a196a
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_analog.c
@@ -0,0 +1,116 @@
+/*
+ wiring_analog.c - analog input and output
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 248 2007-02-03 15:36:30Z mellis $
+*/
+
+#include "wiring_private.h"
+#include "pins_arduino.h"
+
+uint8_t analog_reference = DEFAULT;
+
+void analogReference(uint8_t mode)
+{
+ // can't actually set the register here because the default setting
+ // will connect AVCC and the AREF pin, which would cause a short if
+ // there's something connected to AREF.
+ analog_reference = mode;
+}
+
+int analogRead(uint8_t pin)
+{
+ uint8_t low, high, ch = analogInPinToBit(pin);
+
+ // set the analog reference (high two bits of ADMUX) and select the
+ // channel (low 4 bits). this also sets ADLAR (left-adjust result)
+ // to 0 (the default).
+ // the final AND is to clear the pos/neg reference bits
+ ADMUX = ((analog_reference << 6) | (pin & 0x0f)) & B11000111;
+
+ // without a delay, we seem to read from the wrong channel
+ //delay(1);
+
+ // start the conversion
+ sbi(ADCSRA, ADSC);
+
+ // ADSC is cleared when the conversion finishes
+ while (bit_is_set(ADCSRA, ADSC));
+
+ // we have to read ADCL first; doing so locks both ADCL
+ // and ADCH until ADCH is read. reading ADCL second would
+ // cause the results of each conversion to be discarded,
+ // as ADCL and ADCH would be locked when it completed.
+ low = ADCL;
+ high = ADCH;
+
+ // combine the two bytes
+ return (high << 8) | low;
+}
+
+// Right now, PWM output only works on the pins with
+// hardware support. These are defined in the appropriate
+// pins_*.c file. For the rest of the pins, we default
+// to digital output.
+void analogWrite(uint8_t pin, int val)
+{
+ // We need to make sure the PWM output is enabled for those pins
+ // that support it, as we turn it off when digitally reading or
+ // writing with them. Also, make sure the pin is in output mode
+ // for consistenty with Wiring, which doesn't require a pinMode
+ // call for the analog output pins.
+ pinMode(pin, OUTPUT);
+
+ if (digitalPinToTimer(pin) == TIMER1A) {
+ // connect pwm to pin on timer 1, channel A
+ sbi(TCCR1A, COM1A1);
+ // set pwm duty
+ OCR1A = val;
+ } else if (digitalPinToTimer(pin) == TIMER1B) {
+ // connect pwm to pin on timer 1, channel B
+ sbi(TCCR1A, COM1B1);
+ // set pwm duty
+ OCR1B = val;
+ } else if (digitalPinToTimer(pin) == TIMER0A) {
+ // connect pwm to pin on timer 0, channel A
+ sbi(TCCR0A, COM0A1);
+ // set pwm duty
+ OCR0A = val;
+ } else if (digitalPinToTimer(pin) == TIMER0B) {
+ // connect pwm to pin on timer 0, channel B
+ sbi(TCCR0A, COM0B1);
+ // set pwm duty
+ OCR0B = val;
+ } else if (digitalPinToTimer(pin) == TIMER2A) {
+ // connect pwm to pin on timer 2, channel A
+ sbi(TCCR2A, COM2A1);
+ // set pwm duty
+ OCR2A = val;
+ } else if (digitalPinToTimer(pin) == TIMER2B) {
+ // connect pwm to pin on timer 2, channel B
+ sbi(TCCR2A, COM2B1);
+ // set pwm duty
+ OCR2B = val;
+ } else if (val < 128)
+ //fail semi-intelligently
+ digitalWrite(pin, LOW);
+ else
+ digitalWrite(pin, HIGH);
+}
diff --git a/Marlin/Gen7/cores/arduino/wiring_digital.c b/Marlin/Gen7/cores/arduino/wiring_digital.c
new file mode 100644
index 00000000000..3d4b4ebd1c3
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_digital.c
@@ -0,0 +1,95 @@
+/*
+ wiring_digital.c - digital input and output functions
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 248 2007-02-03 15:36:30Z mellis $
+*/
+
+#include "wiring_private.h"
+#include "pins_arduino.h"
+
+void pinMode(uint8_t pin, uint8_t mode)
+{
+ uint8_t bit = digitalPinToBitMask(pin);
+ uint8_t port = digitalPinToPort(pin);
+ volatile uint8_t *reg;
+
+ if (port == NOT_A_PIN) return;
+
+ // JWS: can I let the optimizer do this?
+ reg = portModeRegister(port);
+
+ if (mode == INPUT) *reg &= ~bit;
+ else *reg |= bit;
+}
+
+// Forcing this inline keeps the callers from having to push their own stuff
+// on the stack. It is a good performance win and only takes 1 more byte per
+// user than calling. (It will take more bytes on the 168.)
+//
+// But shouldn't this be moved into pinMode? Seems silly to check and do on
+// each digitalread or write.
+//
+static inline void turnOffPWM(uint8_t timer) __attribute__ ((always_inline));
+static inline void turnOffPWM(uint8_t timer)
+{
+ if (timer == TIMER0A) cbi(TCCR0A, COM0A1);
+ if (timer == TIMER0B) cbi(TCCR0A, COM0B1);
+ if (timer == TIMER1A) cbi(TCCR1A, COM1A1);
+ if (timer == TIMER1B) cbi(TCCR1A, COM1B1);
+ if (timer == TIMER2A) cbi(TCCR2A, COM2A1);
+ if (timer == TIMER2B) cbi(TCCR2A, COM2B1);
+}
+
+void digitalWrite(uint8_t pin, uint8_t val)
+{
+ uint8_t timer = digitalPinToTimer(pin);
+ uint8_t bit = digitalPinToBitMask(pin);
+ uint8_t port = digitalPinToPort(pin);
+ volatile uint8_t *out;
+
+ if (port == NOT_A_PIN) return;
+
+ // If the pin that support PWM output, we need to turn it off
+ // before doing a digital write.
+ if (timer != NOT_ON_TIMER) turnOffPWM(timer);
+
+ out = portOutputRegister(port);
+
+ if (val == LOW) *out &= ~bit;
+ else *out |= bit;
+}
+
+int digitalRead(uint8_t pin)
+{
+ uint8_t timer = digitalPinToTimer(pin);
+ uint8_t bit = digitalPinToBitMask(pin);
+ uint8_t port = digitalPinToPort(pin);
+
+ if (port == NOT_A_PIN) return LOW;
+
+ // If the pin that support PWM output, we need to turn it off
+ // before getting a digital reading.
+ if (timer != NOT_ON_TIMER) turnOffPWM(timer);
+
+ if (*portInputRegister(port) & bit) return HIGH;
+
+ return LOW;
+}
diff --git a/Marlin/Gen7/cores/arduino/wiring_private.h b/Marlin/Gen7/cores/arduino/wiring_private.h
new file mode 100644
index 00000000000..14394a0b612
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_private.h
@@ -0,0 +1,60 @@
+/*
+ wiring_private.h - Internal header file.
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.h 239 2007-01-12 17:58:39Z mellis $
+*/
+
+#ifndef WiringPrivate_h
+#define WiringPrivate_h
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <avr/signal.h>
+#include <avr/delay.h>
+#include <stdio.h>
+#include <stdarg.h>
+
+#include "wiring.h"
+
+#ifdef __cplusplus
+extern "C"{
+#endif
+
+#ifndef cbi
+#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
+#endif
+#ifndef sbi
+#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
+#endif
+
+#define EXTERNAL_INT_0 0
+#define EXTERNAL_INT_1 1
+#define EXTERNAL_INT_2 2
+
+#define EXTERNAL_NUM_INTERRUPTS 3
+
+typedef void (*voidFuncPtr)(void);
+
+#ifdef __cplusplus
+} // extern "C"
+#endif
+
+#endif
diff --git a/Marlin/Gen7/cores/arduino/wiring_pulse.c b/Marlin/Gen7/cores/arduino/wiring_pulse.c
new file mode 100644
index 00000000000..8f232f1d558
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_pulse.c
@@ -0,0 +1,66 @@
+/*
+ wiring_pulse.c - pulseIn() function
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 248 2007-02-03 15:36:30Z mellis $
+*/
+
+#include "wiring_private.h"
+#include "pins_arduino.h"
+
+/* Measures the length (in microseconds) of a pulse on the pin; state is HIGH
+ * or LOW, the type of pulse to measure. Works on pulses from 2-3 microseconds
+ * to 3 minutes in length, but must be called at least a few dozen microseconds
+ * before the start of the pulse. */
+unsigned long pulseIn(uint8_t pin, uint8_t state, unsigned long timeout)
+{
+ // cache the port and bit of the pin in order to speed up the
+ // pulse width measuring loop and achieve finer resolution. calling
+ // digitalRead() instead yields much coarser resolution.
+ uint8_t bit = digitalPinToBitMask(pin);
+ uint8_t port = digitalPinToPort(pin);
+ uint8_t stateMask = (state ? bit : 0);
+ unsigned long width = 0; // keep initialization out of time critical area
+
+ // convert the timeout from microseconds to a number of times through
+ // the initial loop; it takes 16 clock cycles per iteration.
+ unsigned long numloops = 0;
+ unsigned long maxloops = microsecondsToClockCycles(timeout) / 16;
+
+ // wait for any previous pulse to end
+ while ((*portInputRegister(port) & bit) == stateMask)
+ if (numloops++ == maxloops)
+ return 0;
+
+ // wait for the pulse to start
+ while ((*portInputRegister(port) & bit) != stateMask)
+ if (numloops++ == maxloops)
+ return 0;
+
+ // wait for the pulse to stop
+ while ((*portInputRegister(port) & bit) == stateMask)
+ width++;
+
+ // convert the reading to microseconds. The loop has been determined
+ // to be 10 clock cycles long and have about 16 clocks between the edge
+ // and the start of the loop. There will be some error introduced by
+ // the interrupt handlers.
+ return clockCyclesToMicroseconds(width * 10 + 16);
+}
diff --git a/Marlin/Gen7/cores/arduino/wiring_serial.c b/Marlin/Gen7/cores/arduino/wiring_serial.c
new file mode 100644
index 00000000000..a3314faa892
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_serial.c
@@ -0,0 +1,138 @@
+/*
+ wiring_serial.c - serial functions.
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+ Modified 29 January 2009, Marius Kintel for Sanguino - http://www.sanguino.cc/
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 248 2007-02-03 15:36:30Z mellis $
+*/
+
+
+#include "wiring_private.h"
+
+// Define constants and variables for buffering incoming serial data. We're
+// using a ring buffer (I think), in which rx_buffer_head is the index of the
+// location to which to write the next incoming character and rx_buffer_tail
+// is the index of the location from which to read.
+#define RX_BUFFER_SIZE 128
+
+#if defined(__AVR_ATmega644P__)
+unsigned char rx_buffer[2][RX_BUFFER_SIZE];
+int rx_buffer_head[2] = {0, 0};
+int rx_buffer_tail[2] = {0, 0};
+#else
+unsigned char rx_buffer[1][RX_BUFFER_SIZE];
+int rx_buffer_head[1] = {0};
+int rx_buffer_tail[1] = {0};
+#endif
+
+
+#define BEGIN_SERIAL(uart_, baud_) \
+{ \
+ UBRR##uart_##H = ((F_CPU / 16 + baud / 2) / baud - 1) >> 8; \
+ UBRR##uart_##L = ((F_CPU / 16 + baud / 2) / baud - 1); \
+ \
+ /* reset config for UART */ \
+ UCSR##uart_##A = 0; \
+ UCSR##uart_##B = 0; \
+ UCSR##uart_##C = 0; \
+ \
+ /* enable rx and tx */ \
+ sbi(UCSR##uart_##B, RXEN##uart_);\
+ sbi(UCSR##uart_##B, TXEN##uart_);\
+ \
+ /* enable interrupt on complete reception of a byte */ \
+ sbi(UCSR##uart_##B, RXCIE##uart_); \
+ UCSR##uart_##C = _BV(UCSZ##uart_##1)|_BV(UCSZ##uart_##0); \
+ /* defaults to 8-bit, no parity, 1 stop bit */ \
+}
+
+void beginSerial(uint8_t uart, long baud)
+{
+ if (uart == 0) BEGIN_SERIAL(0, baud)
+#if defined(__AVR_ATmega644P__)
+ else BEGIN_SERIAL(1, baud)
+#endif
+}
+
+#define SERIAL_WRITE(uart_, c_) \
+ while (!(UCSR##uart_##A & (1 << UDRE##uart_))) \
+ ; \
+ UDR##uart_ = c
+
+void serialWrite(uint8_t uart, unsigned char c)
+{
+ if (uart == 0) {
+ SERIAL_WRITE(0, c);
+ }
+#if defined(__AVR_ATmega644P__)
+ else {
+ SERIAL_WRITE(1, c);
+ }
+#endif
+}
+
+int serialAvailable(uint8_t uart)
+{
+ return (RX_BUFFER_SIZE + rx_buffer_head[uart] - rx_buffer_tail[uart]) % RX_BUFFER_SIZE;
+}
+
+int serialRead(uint8_t uart)
+{
+ // if the head isn't ahead of the tail, we don't have any characters
+ if (rx_buffer_head[uart] == rx_buffer_tail[uart]) {
+ return -1;
+ } else {
+ unsigned char c = rx_buffer[uart][rx_buffer_tail[uart]];
+ rx_buffer_tail[uart] = (rx_buffer_tail[uart] + 1) % RX_BUFFER_SIZE;
+ return c;
+ }
+}
+
+void serialFlush(uint8_t uart)
+{
+ // don't reverse this or there may be problems if the RX interrupt
+ // occurs after reading the value of rx_buffer_head but before writing
+ // the value to rx_buffer_tail; the previous value of rx_buffer_head
+ // may be written to rx_buffer_tail, making it appear as if the buffer
+ // were full, not empty.
+ rx_buffer_head[uart] = rx_buffer_tail[uart];
+}
+
+#define UART_ISR(uart_) \
+ISR(USART##uart_##_RX_vect) \
+{ \
+ unsigned char c = UDR##uart_; \
+ \
+ int i = (rx_buffer_head[uart_] + 1) % RX_BUFFER_SIZE; \
+ \
+ /* if we should be storing the received character into the location \
+ just before the tail (meaning that the head would advance to the \
+ current location of the tail), we're about to overflow the buffer \
+ and so we don't write the character or advance the head. */ \
+ if (i != rx_buffer_tail[uart_]) { \
+ rx_buffer[uart_][rx_buffer_head[uart_]] = c; \
+ rx_buffer_head[uart_] = i; \
+ } \
+}
+
+UART_ISR(0)
+#if defined(__AVR_ATmega644P__)
+UART_ISR(1)
+#endif
diff --git a/Marlin/Gen7/cores/arduino/wiring_shift.c b/Marlin/Gen7/cores/arduino/wiring_shift.c
new file mode 100644
index 00000000000..956f8642972
--- /dev/null
+++ b/Marlin/Gen7/cores/arduino/wiring_shift.c
@@ -0,0 +1,40 @@
+/*
+ wiring_shift.c - shiftOut() function
+ Part of Arduino - http://www.arduino.cc/
+
+ Copyright (c) 2005-2006 David A. Mellis
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ Lesser General Public License for more details.
+
+ You should have received a copy of the GNU Lesser General
+ Public License along with this library; if not, write to the
+ Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ Boston, MA 02111-1307 USA
+
+ $Id: wiring.c 248 2007-02-03 15:36:30Z mellis $
+*/
+
+#include "wiring_private.h"
+
+void shiftOut(uint8_t dataPin, uint8_t clockPin, uint8_t bitOrder, byte val)
+{
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ if (bitOrder == LSBFIRST)
+ digitalWrite(dataPin, !!(val & (1 << i)));
+ else
+ digitalWrite(dataPin, !!(val & (1 << (7 - i))));
+
+ digitalWrite(clockPin, HIGH);
+ digitalWrite(clockPin, LOW);
+ }
+}
diff --git a/Marlin/Marlin.pde b/Marlin/Marlin.pde
index b122e58d826..b576ef7b8b7 100644
--- a/Marlin/Marlin.pde
+++ b/Marlin/Marlin.pde
@@ -226,11 +226,11 @@ void setup_photpin()
void setup_powerhold()
{
#ifdef SUICIDE_PIN
- #if (SUICIDE_PIN> -1)
+ #if (SUICIDE_PIN> -1)
SET_OUTPUT(SUICIDE_PIN);
WRITE(SUICIDE_PIN, HIGH);
- #endif
- #endif
+ #endif
+ #endif
}
void suicide()
diff --git a/Marlin/fastio.h b/Marlin/fastio.h
index 42f4ebb4f74..cb4399a9505 100644
--- a/Marlin/fastio.h
+++ b/Marlin/fastio.h
@@ -424,7 +424,7 @@ pins
#define PD7_PWM NULL
#endif /* _AVR_ATmega{168,328,328P}__ */
-#if defined (__AVR_ATmega644__) || defined (__AVR_ATmega644P__) || defined (__AVR_ATmega644PA__)
+#if defined (__AVR_ATmega644__) || defined (__AVR_ATmega644P__) || defined (__AVR_ATmega644PA__) || defined (__AVR_ATmega1284P__)
// UART
#define RXD DIO8
#define TXD DIO9
diff --git a/Marlin/hardware/tools/avr/etc/avrdude.conf b/Marlin/hardware/tools/avr/etc/avrdude.conf
new file mode 100644
index 00000000000..ec921df42f6
--- /dev/null
+++ b/Marlin/hardware/tools/avr/etc/avrdude.conf
@@ -0,0 +1,12104 @@
+# $Id: avrdude.conf.in,v 1.122 2007/05/16 21:29:36 joerg_wunsch Exp $
+#
+# AVRDUDE Configuration File
+#
+# This file contains configuration data used by AVRDUDE which describes
+# the programming hardware pinouts and also provides part definitions.
+# AVRDUDE's "-C" command line option specifies the location of the
+# configuration file. The "-c" option names the programmer configuration
+# which must match one of the entry's "id" parameter. The "-p" option
+# identifies which part AVRDUDE is going to be programming and must match
+# one of the parts' "id" parameter.
+#
+# Possible entry formats are:
+#
+# programmer
+# id = <id1> [, <id2> [, <id3>] ...] ; # <idN> are quoted strings
+# desc = <description> ; # quoted string
+# type = par | stk500 | stk500v2 | stk500pp | stk500hvsp | stk500generic |
+# avr910 | butterfly | usbasp |
+# jtagmki | jtagmkii | jtagmkii_isp | jtagmkii_dw |
+# dragon_dw | dragon_jtag | dragon_isp | dragon_pp |
+# dragon_hvsp; # programmer type
+# baudrate = <num> ; # baudrate for avr910-programmer
+# vcc = <num1> [, <num2> ... ] ; # pin number(s)
+# reset = <num> ; # pin number
+# sck = <num> ; # pin number
+# mosi = <num> ; # pin number
+# miso = <num> ; # pin number
+# errled = <num> ; # pin number
+# rdyled = <num> ; # pin number
+# pgmled = <num> ; # pin number
+# vfyled = <num> ; # pin number
+# ;
+#
+# part
+# id = <id> ; # quoted string
+# desc = <description> ; # quoted string
+# has_jtag = <yes/no> ; # part has JTAG i/f
+# has_debugwire = <yes/no> ; # part has debugWire i/f
+# devicecode = <num> ; # deprecated, use stk500_devcode
+# stk500_devcode = <num> ; # numeric
+# avr910_devcode = <num> ; # numeric
+# signature = <num> <num> <num> ; # signature bytes
+# chip_erase_delay = <num> ; # micro-seconds
+# reset = dedicated | io;
+# retry_pulse = reset | sck;
+# pgm_enable = <instruction format> ;
+# chip_erase = <instruction format> ;
+# chip_erase_delay = <num> ; # chip erase delay (us)
+# # STK500 parameters (parallel programming IO lines)
+# pagel = <num> ; # pin name in hex, i.e., 0xD7
+# bs2 = <num> ; # pin name in hex, i.e., 0xA0
+# serial = <yes/no> ; # can use serial downloading
+# parallel = <yes/no/pseudo>; # can use par. programming
+# # STK500v2 parameters, to be taken from Atmel's XML files
+# timeout = <num> ;
+# stabdelay = <num> ;
+# cmdexedelay = <num> ;
+# synchloops = <num> ;
+# bytedelay = <num> ;
+# pollvalue = <num> ;
+# pollindex = <num> ;
+# predelay = <num> ;
+# postdelay = <num> ;
+# pollmethod = <num> ;
+# mode = <num> ;
+# delay = <num> ;
+# blocksize = <num> ;
+# readsize = <num> ;
+# hvspcmdexedelay = <num> ;
+# # STK500v2 HV programming parameters, from XML
+# pp_controlstack = <num>, <num>, ...; # PP only
+# hvsp_controlstack = <num>, <num>, ...; # HVSP only
+# hventerstabdelay = <num>;
+# progmodedelay = <num>; # PP only
+# latchcycles = <num>;
+# togglevtg = <num>;
+# poweroffdelay = <num>;
+# resetdelayms = <num>;
+# resetdelayus = <num>;
+# hvleavestabdelay = <num>;
+# resetdelay = <num>;
+# synchcycles = <num>; # HVSP only
+# chiperasepulsewidth = <num>; # PP only
+# chiperasepolltimeout = <num>;
+# chiperasetime = <num>; # HVSP only
+# programfusepulsewidth = <num>; # PP only
+# programfusepolltimeout = <num>;
+# programlockpulsewidth = <num>; # PP only
+# programlockpolltimeout = <num>;
+# # JTAG ICE mkII parameters, also from XML files
+# allowfullpagebitstream = <yes/no> ;
+# enablepageprogramming = <yes/no> ;
+# idr = <num> ; # IO addr of IDR (OCD) reg.
+# rampz = <num> ; # IO addr of RAMPZ reg.
+# spmcr = <num> ; # mem addr of SPMC[S]R reg.
+# eecr = <num> ; # mem addr of EECR reg.
+# # (only when != 0x3c)
+#
+# memory <memtype>
+# paged = <yes/no> ; # yes / no
+# size = <num> ; # bytes
+# page_size = <num> ; # bytes
+# num_pages = <num> ; # numeric
+# min_write_delay = <num> ; # micro-seconds
+# max_write_delay = <num> ; # micro-seconds
+# readback_p1 = <num> ; # byte value
+# readback_p2 = <num> ; # byte value
+# pwroff_after_write = <yes/no> ; # yes / no
+# read = <instruction format> ;
+# write = <instruction format> ;
+# read_lo = <instruction format> ;
+# read_hi = <instruction format> ;
+# write_lo = <instruction format> ;
+# write_hi = <instruction format> ;
+# loadpage_lo = <instruction format> ;
+# loadpage_hi = <instruction format> ;
+# writepage = <instruction format> ;
+# ;
+# ;
+#
+# If any of the above parameters are not specified, the default value
+# of 0 is used for numerics or the empty string ("") for string
+# values. If a required parameter is left empty, AVRDUDE will
+# complain.
+#
+# NOTES:
+# * 'devicecode' is the device code used by the STK500 (see codes
+# listed below)
+# * Not all memory types will implement all instructions.
+# * AVR Fuse bits and Lock bits are implemented as a type of memory.
+# * Example memory types are:
+# "flash", "eeprom", "fuse", "lfuse" (low fuse), "hfuse" (high
+# fuse), "signature", "calibration", "lock"
+# * The memory type specified on the avrdude command line must match
+# one of the memory types defined for the specified chip.
+# * The pwroff_after_write flag causes avrdude to attempt to
+# power the device off and back on after an unsuccessful write to
+# the affected memory area if VCC programmer pins are defined. If
+# VCC pins are not defined for the programmer, a message
+# indicating that the device needs a power-cycle is printed out.
+# This flag was added to work around a problem with the
+# at90s4433/2333's; see the at90s4433 errata at:
+#
+# http://www.atmel.com/atmel/acrobat/doc1280.pdf
+#
+# INSTRUCTION FORMATS
+#
+# Instruction formats are specified as a comma seperated list of
+# string values containing information (bit specifiers) about each
+# of the 32 bits of the instruction. Bit specifiers may be one of
+# the following formats:
+#
+# '1' = the bit is always set on input as well as output
+#
+# '0' = the bit is always clear on input as well as output
+#
+# 'x' = the bit is ignored on input and output
+#
+# 'a' = the bit is an address bit, the bit-number matches this bit
+# specifier's position within the current instruction byte
+#
+# 'aN' = the bit is the Nth address bit, bit-number = N, i.e., a12
+# is address bit 12 on input, a0 is address bit 0.
+#
+# 'i' = the bit is an input data bit
+#
+# 'o' = the bit is an output data bit
+#
+# Each instruction must be composed of 32 bit specifiers. The
+# instruction specification closely follows the instruction data
+# provided in Atmel's data sheets for their parts.
+#
+# See below for some examples.
+#
+#
+# The following are STK500 part device codes to use for the
+# "devicecode" field of the part. These came from Atmel's software
+# section avr061.zip which accompanies the application note
+# AVR061 available from:
+#
+# http://www.atmel.com/atmel/acrobat/doc2525.pdf
+#
+
+#define ATTINY10 0x10
+#define ATTINY11 0x11
+#define ATTINY12 0x12
+#define ATTINY15 0x13
+#define ATTINY13 0x14
+
+#define ATTINY22 0x20
+#define ATTINY26 0x21
+#define ATTINY28 0x22
+#define ATTINY2313 0x23
+
+#define AT90S1200 0x33
+
+#define AT90S2313 0x40
+#define AT90S2323 0x41
+#define AT90S2333 0x42
+#define AT90S2343 0x43
+
+#define AT90S4414 0x50
+#define AT90S4433 0x51
+#define AT90S4434 0x52
+#define ATMEGA48 0x59
+
+#define AT90S8515 0x60
+#define AT90S8535 0x61
+#define AT90C8534 0x62
+#define ATMEGA8515 0x63
+#define ATMEGA8535 0x64
+
+#define ATMEGA8 0x70
+#define ATMEGA88 0x73
+#define ATMEGA168 0x86
+
+#define ATMEGA161 0x80
+#define ATMEGA163 0x81
+#define ATMEGA16 0x82
+#define ATMEGA162 0x83
+#define ATMEGA169 0x84
+
+#define ATMEGA323 0x90
+#define ATMEGA32 0x91
+
+#define ATMEGA64 0xA0
+
+#define ATMEGA103 0xB1
+#define ATMEGA128 0xB2
+#define AT90CAN128 0xB3
+
+#define AT86RF401 0xD0
+
+#define AT89START 0xE0
+#define AT89S51 0xE0
+#define AT89S52 0xE1
+
+# The following table lists the devices in the original AVR910
+# appnote:
+# |Device |Signature | Code |
+# +-------+----------+------+
+# |tiny12 | 1E 90 05 | 0x55 |
+# |tiny15 | 1E 90 06 | 0x56 |
+# | | | |
+# | S1200 | 1E 90 01 | 0x13 |
+# | | | |
+# | S2313 | 1E 91 01 | 0x20 |
+# | S2323 | 1E 91 02 | 0x48 |
+# | S2333 | 1E 91 05 | 0x34 |
+# | S2343 | 1E 91 03 | 0x4C |
+# | | | |
+# | S4414 | 1E 92 01 | 0x28 |
+# | S4433 | 1E 92 03 | 0x30 |
+# | S4434 | 1E 92 02 | 0x6C |
+# | | | |
+# | S8515 | 1E 93 01 | 0x38 |
+# | S8535 | 1E 93 03 | 0x68 |
+# | | | |
+# |mega32 | 1E 95 01 | 0x72 |
+# |mega83 | 1E 93 05 | 0x65 |
+# |mega103| 1E 97 01 | 0x41 |
+# |mega161| 1E 94 01 | 0x60 |
+# |mega163| 1E 94 02 | 0x64 |
+
+# Appnote AVR109 also has a table of AVR910 device codes, which
+# lists:
+# dev avr910 signature
+# ATmega8 0x77 0x1E 0x93 0x07
+# ATmega8515 0x3B 0x1E 0x93 0x06
+# ATmega8535 0x6A 0x1E 0x93 0x08
+# ATmega16 0x75 0x1E 0x94 0x03
+# ATmega162 0x63 0x1E 0x94 0x04
+# ATmega163 0x66 0x1E 0x94 0x02
+# ATmega169 0x79 0x1E 0x94 0x05
+# ATmega32 0x7F 0x1E 0x95 0x02
+# ATmega323 0x73 0x1E 0x95 0x01
+# ATmega64 0x46 0x1E 0x96 0x02
+# ATmega128 0x44 0x1E 0x97 0x02
+#
+# These codes refer to "BOOT" device codes which are apparently
+# different than standard device codes, for whatever reasons
+# (often one above the standard code).
+
+# There are several extended versions of AVR910 implementations around
+# in the Internet. These add the following codes (only devices that
+# actually exist are listed):
+
+# ATmega8515 0x3A
+# ATmega128 0x43
+# ATmega64 0x45
+# ATtiny26 0x5E
+# ATmega8535 0x69
+# ATmega32 0x72
+# ATmega16 0x74
+# ATmega8 0x76
+# ATmega169 0x78
+
+#
+# Overall avrdude defaults
+#
+default_parallel = "lpt1";
+default_serial = "com1";
+
+
+#
+# PROGRAMMER DEFINITIONS
+#
+
+programmer
+ id = "avrisp";
+ desc = "Atmel AVR ISP";
+ type = stk500;
+;
+
+programmer
+ id = "avrispv2";
+ desc = "Atmel AVR ISP V2";
+ type = stk500v2;
+;
+
+programmer
+ id = "avrispmkII";
+ desc = "Atmel AVR ISP mkII";
+ type = stk500v2;
+;
+
+programmer
+ id = "avrisp2";
+ desc = "Atmel AVR ISP mkII";
+ type = stk500v2;
+;
+
+# This is supposed to be the "default" STK500 entry.
+# Attempts to select the correct firmware version
+# by probing for it. Better use one of the entries
+# below instead.
+programmer
+ id = "stk500";
+ desc = "Atmel STK500";
+ type = stk500generic;
+;
+
+programmer
+ id = "stk500v1";
+ desc = "Atmel STK500 Version 1.x firmware";
+ type = stk500;
+;
+
+programmer
+ id = "stk500v2";
+ desc = "Atmel STK500 Version 2.x firmware";
+ type = stk500v2;
+;
+
+programmer
+ id = "stk500pp";
+ desc = "Atmel STK500 V2 in parallel programming mode";
+ type = stk500pp;
+;
+
+programmer
+ id = "stk500hvsp";
+ desc = "Atmel STK500 V2 in high-voltage serial programming mode";
+ type = stk500hvsp;
+;
+
+programmer
+ id = "avr910";
+ desc = "Atmel Low Cost Serial Programmer";
+ type = avr910;
+;
+
+programmer
+ id = "usbasp";
+ desc = "USBasp, http://www.fischl.de/usbasp/";
+ type = usbasp;
+;
+
+programmer
+ id = "usbtiny";
+ desc = "USBtiny simple USB programmer";
+ type = usbtiny;
+;
+
+programmer
+ id = "butterfly";
+ desc = "Atmel Butterfly Development Board";
+ type = butterfly;
+;
+
+programmer
+ id = "avr109";
+ desc = "Atmel AppNote AVR109 Boot Loader";
+ type = butterfly;
+;
+
+programmer
+ id = "avr911";
+ desc = "Atmel AppNote AVR911 AVROSP";
+ type = butterfly;
+;
+
+programmer
+ id = "jtagmkI";
+ desc = "Atmel JTAG ICE (mkI)";
+ baudrate = 115200; # default is 115200
+ type = jtagmki;
+;
+
+# easier to type
+programmer
+ id = "jtag1";
+ desc = "Atmel JTAG ICE (mkI)";
+ baudrate = 115200; # default is 115200
+ type = jtagmki;
+;
+
+# easier to type
+programmer
+ id = "jtag1slow";
+ desc = "Atmel JTAG ICE (mkI)";
+ baudrate = 19200;
+ type = jtagmki;
+;
+
+programmer
+ id = "jtagmkII";
+ desc = "Atmel JTAG ICE mkII";
+ baudrate = 19200; # default is 19200
+ type = jtagmkii;
+;
+
+# easier to type
+programmer
+ id = "jtag2slow";
+ desc = "Atmel JTAG ICE mkII";
+ baudrate = 19200; # default is 19200
+ type = jtagmkii;
+;
+
+# JTAG ICE mkII @ 115200 Bd
+programmer
+ id = "jtag2fast";
+ desc = "Atmel JTAG ICE mkII";
+ baudrate = 115200;
+ type = jtagmkii;
+;
+
+# make the fast one the default, people will love that
+programmer
+ id = "jtag2";
+ desc = "Atmel JTAG ICE mkII";
+ baudrate = 115200;
+ type = jtagmkii;
+;
+
+# JTAG ICE mkII in ISP mode
+programmer
+ id = "jtag2isp";
+ desc = "Atmel JTAG ICE mkII in ISP mode";
+ baudrate = 115200;
+ type = jtagmkii_isp;
+;
+
+# JTAG ICE mkII in debugWire mode
+programmer
+ id = "jtag2dw";
+ desc = "Atmel JTAG ICE mkII in debugWire mode";
+ baudrate = 115200;
+ type = jtagmkii_dw;
+;
+
+# AVR Dragon in JTAG mode
+programmer
+ id = "dragon_jtag";
+ desc = "Atmel AVR Dragon in JTAG mode";
+ baudrate = 115200;
+ type = dragon_jtag;
+;
+
+# AVR Dragon in ISP mode
+programmer
+ id = "dragon_isp";
+ desc = "Atmel AVR Dragon in ISP mode";
+ baudrate = 115200;
+ type = dragon_isp;
+;
+
+# AVR Dragon in PP mode
+programmer
+ id = "dragon_pp";
+ desc = "Atmel AVR Dragon in PP mode";
+ baudrate = 115200;
+ type = dragon_pp;
+;
+
+# AVR Dragon in HVSP mode
+programmer
+ id = "dragon_hvsp";
+ desc = "Atmel AVR Dragon in HVSP mode";
+ baudrate = 115200;
+ type = dragon_hvsp;
+;
+
+# AVR Dragon in debugWire mode
+programmer
+ id = "dragon_dw";
+ desc = "Atmel AVR Dragon in debugWire mode";
+ baudrate = 115200;
+ type = dragon_dw;
+;
+
+programmer
+ id = "pavr";
+ desc = "Jason Kyle's pAVR Serial Programmer";
+ type = avr910;
+;
+
+# Parallel port programmers.
+
+programmer
+ id = "bsd";
+ desc = "Brian Dean's Programmer, http://www.bsdhome.com/avrdude/";
+ type = par;
+ vcc = 2, 3, 4, 5;
+ reset = 7;
+ sck = 8;
+ mosi = 9;
+ miso = 10;
+;
+
+programmer
+ id = "stk200";
+ desc = "STK200";
+ type = par;
+ buff = 4, 5;
+ sck = 6;
+ mosi = 7;
+ reset = 9;
+ miso = 10;
+;
+
+# The programming dongle used by the popular Ponyprog
+# utility. It is almost similar to the STK200 one,
+# except that there is a LED indicating that the
+# programming is currently in progress.
+
+programmer
+ id = "pony-stk200";
+ desc = "Pony Prog STK200";
+ type = par;
+ buff = 4, 5;
+ sck = 6;
+ mosi = 7;
+ reset = 9;
+ miso = 10;
+ pgmled = 8;
+;
+
+programmer
+ id = "dt006";
+ desc = "Dontronics DT006";
+ type = par;
+ reset = 4;
+ sck = 5;
+ mosi = 2;
+ miso = 11;
+;
+
+programmer
+ id = "bascom";
+ desc = "Bascom SAMPLE programming cable";
+ type = par;
+ reset = 4;
+ sck = 5;
+ mosi = 2;
+ miso = 11;
+;
+
+programmer
+ id = "alf";
+ desc = "Nightshade ALF-PgmAVR, http://nightshade.homeip.net/";
+ type = par;
+ vcc = 2, 3, 4, 5;
+ buff = 6;
+ reset = 7;
+ sck = 8;
+ mosi = 9;
+ miso = 10;
+ errled = 1;
+ rdyled = 14;
+ pgmled = 16;
+ vfyled = 17;
+;
+
+programmer
+ id = "sp12";
+ desc = "Steve Bolt's Programmer";
+ type = par;
+ vcc = 4,5,6,7,8;
+ reset = 3;
+ sck = 2;
+ mosi = 9;
+ miso = 11;
+;
+
+programmer
+ id = "picoweb";
+ desc = "Picoweb Programming Cable, http://www.picoweb.net/";
+ type = par;
+ reset = 2;
+ sck = 3;
+ mosi = 4;
+ miso = 13;
+;
+
+programmer
+ id = "abcmini";
+ desc = "ABCmini Board, aka Dick Smith HOTCHIP";
+ type = par;
+ reset = 4;
+ sck = 3;
+ mosi = 2;
+ miso = 10;
+;
+
+programmer
+ id = "futurlec";
+ desc = "Futurlec.com programming cable.";
+ type = par;
+ reset = 3;
+ sck = 2;
+ mosi = 1;
+ miso = 10;
+;
+
+
+# From the contributor of the "xil" jtag cable:
+# The "vcc" definition isn't really vcc (the cable gets its power from
+# the programming circuit) but is necessary to switch one of the
+# buffer lines (trying to add it to the "buff" lines doesn't work).
+# With this, TMS connects to RESET, TDI to MOSI, TDO to MISO and TCK
+# to SCK (plus vcc/gnd of course)
+programmer
+ id = "xil";
+ desc = "Xilinx JTAG cable";
+ type = par;
+ mosi = 2;
+ sck = 3;
+ reset = 4;
+ buff = 5;
+ miso = 13;
+ vcc = 6;
+;
+
+
+programmer
+ id = "dapa";
+ desc = "Direct AVR Parallel Access cable";
+ type = par;
+ vcc = 3;
+ reset = 16;
+ sck = 1;
+ mosi = 2;
+ miso = 11;
+;
+
+programmer
+ id = "atisp";
+ desc = "AT-ISP V1.1 programming cable for AVR-SDK1 from <http://micro-research.co.th/> micro-research.co.th";
+ type = par;
+ reset = ~6;
+ sck = ~8;
+ mosi = ~7;
+ miso = ~10;
+;
+
+programmer
+ id = "ere-isp-avr";
+ desc = "ERE ISP-AVR <http://www.ere.co.th/download/sch050713.pdf>";
+ type = par;
+ reset = ~4;
+ sck = 3;
+ mosi = 2;
+ miso = 10;
+;
+
+programmer
+ id = "blaster";
+ desc = "Altera ByteBlaster";
+ type = par;
+ sck = 2;
+ miso = 11;
+ reset = 3;
+ mosi = 8;
+ buff = 14;
+;
+
+# It is almost same as pony-stk200, except vcc on pin 5 to auto
+# disconnect port (download on http://electropol.free.fr)
+programmer
+ id = "frank-stk200";
+ desc = "Frank STK200";
+ type = par;
+ vcc = 5;
+ sck = 6;
+ mosi = 7;
+ reset = 9;
+ miso = 10;
+ pgmled = 8;
+;
+
+
+#
+# some ultra cheap programmers use bitbanging on the
+# serialport.
+#
+# PC - DB9 - Pins for RS232:
+#
+# GND 5 -- |O
+# | O| <- 9 RI
+# DTR 4 <- |O |
+# | O| <- 8 CTS
+# TXD 3 <- |O |
+# | O| -> 7 RTS
+# RXD 2 -> |O |
+# | O| <- 6 DSR
+# DCD 1 -> |O
+#
+# Using RXD is currently not supported.
+# Using RI is not supported under Win32 but is supported under Posix.
+
+# serial ponyprog design (dasa2 in uisp)
+# reset=!txd sck=rts mosi=dtr miso=cts
+
+programmer
+ id = "ponyser";
+ desc = "design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts";
+ type = serbb;
+ reset = ~3;
+ sck = 7;
+ mosi = 4;
+ miso = 8;
+;
+
+# Same as above, different name
+# reset=!txd sck=rts mosi=dtr miso=cts
+
+programmer
+ id = "siprog";
+ desc = "Lancos SI-Prog <http://www.lancos.com/siprogsch.html>";
+ type = serbb;
+ reset = ~3;
+ sck = 7;
+ mosi = 4;
+ miso = 8;
+;
+
+# unknown (dasa in uisp)
+# reset=rts sck=dtr mosi=txd miso=cts
+
+programmer
+ id = "dasa";
+ desc = "serial port banging, reset=rts sck=dtr mosi=txd miso=cts";
+ type = serbb;
+ reset = 7;
+ sck = 4;
+ mosi = 3;
+ miso = 8;
+;
+
+# unknown (dasa3 in uisp)
+# reset=!dtr sck=rts mosi=txd miso=cts
+
+programmer
+ id = "dasa3";
+ desc = "serial port banging, reset=!dtr sck=rts mosi=txd miso=cts";
+ type = serbb;
+ reset = ~4;
+ sck = 7;
+ mosi = 3;
+ miso = 8;
+;
+
+#
+# PART DEFINITIONS
+#
+
+#------------------------------------------------------------
+# ATtiny11
+#------------------------------------------------------------
+
+# This is an HVSP-only device.
+
+part
+ id = "t11";
+ desc = "ATtiny11";
+ stk500_devcode = 0x11;
+ signature = 0x1e 0x90 0x04;
+ chip_erase_delay = 20000;
+
+ timeout = 200;
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x00,
+ 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78,
+ 0x78, 0x00, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 50;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 64;
+ blocksize = 64;
+ readsize = 256;
+ delay = 5;
+ ;
+
+ memory "flash"
+ size = 1024;
+ blocksize = 128;
+ readsize = 256;
+ delay = 3;
+ ;
+
+ memory "signature"
+ size = 3;
+ ;
+
+ memory "lock"
+ size = 1;
+ ;
+
+ memory "calibration"
+ size = 1;
+ ;
+
+ memory "fuse"
+ size = 1;
+ ;
+;
+
+#------------------------------------------------------------
+# ATtiny12
+#------------------------------------------------------------
+
+part
+ id = "t12";
+ desc = "ATtiny12";
+ stk500_devcode = 0x12;
+ avr910_devcode = 0x55;
+ signature = 0x1e 0x90 0x05;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x00,
+ 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78,
+ 0x78, 0x00, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 50;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 64;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 8;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ size = 1024;
+ min_write_delay = 4500;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 5;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "fuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 x x x x x",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+;
+
+#------------------------------------------------------------
+# ATtiny13
+#------------------------------------------------------------
+
+part
+ id = "t13";
+ desc = "ATtiny13";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x0E, 0x1E;
+ eeprom_instr = 0xBB, 0xFE, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x0E, 0xB4, 0x0E, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+ stk500_devcode = 0x14;
+ signature = 0x1e 0x90 0x07;
+ chip_erase_delay = 4000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 90;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 64;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 5;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 1024;
+ page_size = 32;
+ num_pages = 32;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 0 0 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 0 0 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 2;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ ;
+
+;
+
+
+#------------------------------------------------------------
+# ATtiny15
+#------------------------------------------------------------
+
+part
+ id = "t15";
+ desc = "ATtiny15";
+ stk500_devcode = 0x13;
+ avr910_devcode = 0x56;
+ signature = 0x1e 0x90 0x06;
+ chip_erase_delay = 8200;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x00,
+ 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78,
+ 0x78, 0x00, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 5;
+ synchcycles = 6;
+ latchcycles = 16;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 50;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 64;
+ min_write_delay = 8200;
+ max_write_delay = 8200;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ size = 1024;
+ min_write_delay = 4100;
+ max_write_delay = 4100;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 5;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "fuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x o o o o x x o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 x x x x x",
+ "x x x x x x x x i i i i 1 1 i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+;
+
+#------------------------------------------------------------
+# AT90s1200
+#------------------------------------------------------------
+
+part
+ id = "1200";
+ desc = "AT90S1200";
+ stk500_devcode = 0x33;
+ avr910_devcode = 0x13;
+ signature = 0x1e 0x90 0x01;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 1;
+ bytedelay = 0;
+ pollindex = 0;
+ pollvalue = 0xFF;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 64;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x x a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 20;
+ blocksize = 32;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 1024;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x02;
+ delay = 15;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ ;
+ memory "lock"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s4414
+#------------------------------------------------------------
+
+part
+ id = "4414";
+ desc = "AT90S4414";
+ stk500_devcode = 0x50;
+ avr910_devcode = 0x28;
+ signature = 0x1e 0x92 0x01;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 256;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x80;
+ readback_p2 = 0x7f;
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x7f;
+ readback_p2 = 0x7f;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s2313
+#------------------------------------------------------------
+
+part
+ id = "2313";
+ desc = "AT90S2313";
+ stk500_devcode = 0x40;
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x91 0x01;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 128;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x80;
+ readback_p2 = 0x7f;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 2048;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x7f;
+ readback_p2 = 0x7f;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x i i x",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s2333
+#------------------------------------------------------------
+
+part
+ id = "2333";
+##### WARNING: No XML file for device 'AT90S2333'! #####
+ desc = "AT90S2333";
+ stk500_devcode = 0x42;
+ avr910_devcode = 0x34;
+ signature = 0x1e 0x91 0x05;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ memory "eeprom"
+ size = 128;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+ ;
+ memory "flash"
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ pwroff_after_write = yes;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 i i i i i",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ memory "lock"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega1284P
+#------------------------------------------------------------
+
+# similar to ATmega164p
+
+part
+ id = "m1284p";
+ desc = "ATMEGA1284P";
+ has_jtag = yes;
+ stk500_devcode = 0x82; # no STK500v1 support, use the ATmega16 one
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x97 0x05;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s2343 (also AT90s2323 and ATtiny22)
+#------------------------------------------------------------
+
+part
+ id = "2343";
+ desc = "AT90S2343";
+ stk500_devcode = 0x43;
+ avr910_devcode = 0x4c;
+ signature = 0x1e 0x91 0x03;
+ chip_erase_delay = 18000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x00,
+ 0x68, 0x78, 0x68, 0x68, 0x00, 0x00, 0x68, 0x78,
+ 0x78, 0x00, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 0;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 50;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 128;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 128;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x o o o x x x x o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 1 1 1 1 i",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ memory "lock"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x o o o x x x x o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# AT90s4433
+#------------------------------------------------------------
+
+part
+ id = "4433";
+ desc = "AT90S4433";
+ stk500_devcode = 0x51;
+ avr910_devcode = 0x30;
+ signature = 0x1e 0x92 0x03;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 256;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ pwroff_after_write = yes;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 i i i i i",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ memory "lock"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s4434
+#------------------------------------------------------------
+
+part
+ id = "4434";
+##### WARNING: No XML file for device 'AT90S4434'! #####
+ desc = "AT90S4434";
+ stk500_devcode = 0x52;
+ avr910_devcode = 0x6c;
+ signature = 0x1e 0x92 0x02;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ memory "eeprom"
+ size = 256;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+ ;
+ memory "flash"
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 i i i i i",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ memory "lock"
+ size = 1;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s8515
+#------------------------------------------------------------
+
+part
+ id = "8515";
+ desc = "AT90S8515";
+ stk500_devcode = 0x60;
+ avr910_devcode = 0x38;
+ signature = 0x1e 0x93 0x01;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x80;
+ readback_p2 = 0x7f;
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 8192;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x7f;
+ readback_p2 = 0x7f;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90s8535
+#------------------------------------------------------------
+
+part
+ id = "8535";
+ desc = "AT90S8535";
+ stk500_devcode = 0x61;
+ avr910_devcode = 0x68;
+ signature = 0x1e 0x93 0x03;
+ chip_erase_delay = 20000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 1;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0x00;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ size = 8192;
+ min_write_delay = 9000;
+ max_write_delay = 20000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ write_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "fuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x x x o";
+ write = "1 0 1 0 1 1 0 0 1 0 1 1 1 1 1 i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x o o x x x x x x";
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega103
+#------------------------------------------------------------
+
+part
+ id = "m103";
+ desc = "ATMEGA103";
+ stk500_devcode = 0xB1;
+ avr910_devcode = 0x41;
+ signature = 0x1e 0x97 0x01;
+ chip_erase_delay = 112000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x8E, 0x9E, 0x2E, 0x3E, 0xAE, 0xBE,
+ 0x4E, 0x5E, 0xCE, 0xDE, 0x6E, 0x7E, 0xEE, 0xDE,
+ 0x66, 0x76, 0xE6, 0xF6, 0x6A, 0x7A, 0xEA, 0x7A,
+ 0x7F, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 15;
+ chiperasepolltimeout = 0;
+ programfusepulsewidth = 2;
+ programfusepolltimeout = 0;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 10;
+
+ memory "eeprom"
+ size = 4096;
+ min_write_delay = 4000;
+ max_write_delay = 9000;
+ readback_p1 = 0x80;
+ readback_p2 = 0x7f;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 22000;
+ max_write_delay = 56000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x11;
+ delay = 70;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "fuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x o x o 1 o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 1 i 1 i i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x o o x";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 i i 1",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega64
+#------------------------------------------------------------
+
+part
+ id = "m64";
+ desc = "ATMEGA64";
+ has_jtag = yes;
+ stk500_devcode = 0xA0;
+ avr910_devcode = 0x45;
+ signature = 0x1e 0x96 0x02;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x22;
+ spmcr = 0x68;
+ allowfullpagebitstream = yes;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 20;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+
+
+#------------------------------------------------------------
+# ATmega128
+#------------------------------------------------------------
+
+part
+ id = "m128";
+ desc = "ATMEGA128";
+ has_jtag = yes;
+ stk500_devcode = 0xB2;
+ avr910_devcode = 0x43;
+ signature = 0x1e 0x97 0x02;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x22;
+ spmcr = 0x68;
+ rampz = 0x3b;
+ allowfullpagebitstream = yes;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 12;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90CAN128
+#------------------------------------------------------------
+
+part
+ id = "c128";
+ desc = "AT90CAN128";
+ has_jtag = yes;
+ stk500_devcode = 0xB3;
+# avr910_devcode = 0x43;
+ signature = 0x1e 0x97 0x81;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ eecr = 0x3f;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega16
+#------------------------------------------------------------
+
+part
+ id = "m16";
+ desc = "ATMEGA16";
+ has_jtag = yes;
+ stk500_devcode = 0x82;
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x94 0x03;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 100;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = yes;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "calibration"
+ size = 4;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega164P
+#------------------------------------------------------------
+
+# close to ATmega16
+
+part
+ id = "m164p";
+ desc = "ATMEGA164P";
+ has_jtag = yes;
+# stk500_devcode = 0x82; # no STK500v1 support
+# avr910_devcode = 0x?; # try the ATmega16 one:^
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x94 0x0a;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega324P
+#------------------------------------------------------------
+
+# similar to ATmega164P
+
+part
+ id = "m324p";
+ desc = "ATMEGA324P";
+ has_jtag = yes;
+# stk500_devcode = 0x82; # no STK500v1 support
+# avr910_devcode = 0x?; # try the ATmega16 one:^
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x95 0x08;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega644
+#------------------------------------------------------------
+
+# similar to ATmega164
+
+part
+ id = "m644";
+ desc = "ATMEGA644";
+ has_jtag = yes;
+# stk500_devcode = 0x82; # no STK500v1 support
+# avr910_devcode = 0x?; # try the ATmega16 one:^
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x96 0x09;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega644P
+#------------------------------------------------------------
+
+# similar to ATmega164p
+
+part
+ id = "m644p";
+ desc = "ATMEGA644P";
+ has_jtag = yes;
+# stk500_devcode = 0x82; # no STK500v1 support
+# avr910_devcode = 0x?; # try the ATmega16 one:^
+ avr910_devcode = 0x74;
+ signature = 0x1e 0x96 0x0a;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+
+
+#------------------------------------------------------------
+# ATmega162
+#------------------------------------------------------------
+
+part
+ id = "m162";
+ desc = "ATMEGA162";
+ has_jtag = yes;
+ stk500_devcode = 0x83;
+ avr910_devcode = 0x63;
+ signature = 0x1e 0x94 0x04;
+ chip_erase_delay = 9000;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+
+ idr = 0x04;
+ spmcr = 0x57;
+ allowfullpagebitstream = yes;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+
+ ;
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 16000;
+ max_write_delay = 16000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 16000;
+ max_write_delay = 16000;
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 16000;
+ max_write_delay = 16000;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 16000;
+ max_write_delay = 16000;
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+
+ read = "0 0 1 1 0 0 0 0 0 0 x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+;
+
+
+
+#------------------------------------------------------------
+# ATmega163
+#------------------------------------------------------------
+
+part
+ id = "m163";
+ desc = "ATMEGA163";
+ stk500_devcode = 0x81;
+ avr910_devcode = 0x64;
+ signature = 0x1e 0x94 0x02;
+ chip_erase_delay = 32000;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 30;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 2;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 2;
+
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 4000;
+ max_write_delay = 4000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 16000;
+ max_write_delay = 16000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o x x o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i 1 1 i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x 1 o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x 1 1 1 1 1 i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x 0 x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega169
+#------------------------------------------------------------
+
+part
+ id = "m169";
+ desc = "ATMEGA169";
+ has_jtag = yes;
+ stk500_devcode = 0x85;
+ avr910_devcode = 0x78;
+ signature = 0x1e 0x94 0x05;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega329
+#------------------------------------------------------------
+
+part
+ id = "m329";
+ desc = "ATMEGA329";
+ has_jtag = yes;
+# stk500_devcode = 0x85; # no STK500 support, only STK500v2
+# avr910_devcode = 0x?; # try the ATmega169 one:
+ avr910_devcode = 0x75;
+ signature = 0x1e 0x95 0x03;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega3290
+#------------------------------------------------------------
+
+# identical to ATmega329
+
+part
+ id = "m3290";
+ desc = "ATMEGA3290";
+ has_jtag = yes;
+# stk500_devcode = 0x85; # no STK500 support, only STK500v2
+# avr910_devcode = 0x?; # try the ATmega169 one:
+ avr910_devcode = 0x75;
+ signature = 0x1e 0x95 0x04;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a3 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega649
+#------------------------------------------------------------
+
+part
+ id = "m649";
+ desc = "ATMEGA649";
+ has_jtag = yes;
+# stk500_devcode = 0x85; # no STK500 support, only STK500v2
+# avr910_devcode = 0x?; # try the ATmega169 one:
+ avr910_devcode = 0x75;
+ signature = 0x1e 0x96 0x03;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega6490
+#------------------------------------------------------------
+
+# identical to ATmega649
+
+part
+ id = "m6490";
+ desc = "ATMEGA6490";
+ has_jtag = yes;
+# stk500_devcode = 0x85; # no STK500 support, only STK500v2
+# avr910_devcode = 0x?; # try the ATmega169 one:
+ avr910_devcode = 0x75;
+ signature = 0x1e 0x96 0x04;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 20;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega32
+#------------------------------------------------------------
+
+part
+ id = "m32";
+ desc = "ATMEGA32";
+ has_jtag = yes;
+ stk500_devcode = 0x91;
+ avr910_devcode = 0x72;
+ signature = 0x1e 0x95 0x02;
+ chip_erase_delay = 9000;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = yes;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 0 0 x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega161
+#------------------------------------------------------------
+
+part
+ id = "m161";
+ desc = "ATMEGA161";
+ stk500_devcode = 0x80;
+ avr910_devcode = 0x60;
+ signature = 0x1e 0x94 0x01;
+ chip_erase_delay = 28000;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 0;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 30;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 2;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 2;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 3400;
+ max_write_delay = 3400;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 5;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 14000;
+ max_write_delay = 14000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 16;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "fuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x x x x o x o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 x x x x x",
+ "x x x x x x x x 1 i 1 i i i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega8
+#------------------------------------------------------------
+
+part
+ id = "m8";
+ desc = "ATMEGA8";
+ stk500_devcode = 0x70;
+ avr910_devcode = 0x76;
+ signature = 0x1e 0x93 0x07;
+ pagel = 0xd7;
+ bs2 = 0xc2;
+ chip_erase_delay = 10000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 2;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 20;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 10;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 0 0 x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+
+#------------------------------------------------------------
+# ATmega8515
+#------------------------------------------------------------
+
+part
+ id = "m8515";
+ desc = "ATMEGA8515";
+ stk500_devcode = 0x63;
+ avr910_devcode = 0x3A;
+ signature = 0x1e 0x93 0x06;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 0 0 x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+
+
+#------------------------------------------------------------
+# ATmega8535
+#------------------------------------------------------------
+
+part
+ id = "m8535";
+ desc = "ATMEGA8535";
+ stk500_devcode = 0x64;
+ avr910_devcode = 0x69;
+ signature = 0x1e 0x93 0x08;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 6;
+ togglevtg = 0;
+ poweroffdelay = 0;
+ resetdelayms = 0;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 2000;
+ max_write_delay = 2000;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 0 0 x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATtiny26
+#------------------------------------------------------------
+
+part
+ id = "t26";
+ desc = "ATTINY26";
+ stk500_devcode = 0x21;
+ avr910_devcode = 0x5e;
+ signature = 0x1e 0x91 0x09;
+ pagel = 0xb3;
+ bs2 = 0xb2;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0xC4, 0xE4, 0xC4, 0xE4, 0xCC, 0xEC, 0xCC, 0xEC,
+ 0xD4, 0xF4, 0xD4, 0xF4, 0xDC, 0xFC, 0xDC, 0xFC,
+ 0xC8, 0xE8, 0xD8, 0xF8, 0x4C, 0x6C, 0x5C, 0x7C,
+ 0xEC, 0xBC, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 2;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 128;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ mode = 0x04;
+ delay = 10;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 2048;
+ page_size = 32;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x21;
+ delay = 6;
+ blocksize = 16;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x x o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 1 i i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x x x x i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 4;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+;
+
+
+#------------------------------------------------------------
+# ATtiny261
+#------------------------------------------------------------
+# Close to ATtiny26
+
+part
+ id = "t261";
+ desc = "ATTINY261";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x00, 0x10;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x00, 0xB4, 0x00, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+# stk500_devcode = 0x21;
+# avr910_devcode = 0x5e;
+ signature = 0x1e 0x91 0x0c;
+ pagel = 0xb3;
+ bs2 = 0xb2;
+ chip_erase_delay = 4000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0xC4, 0xE4, 0xC4, 0xE4, 0xCC, 0xEC, 0xCC, 0xEC,
+ 0xD4, 0xF4, 0xD4, 0xF4, 0xDC, 0xFC, 0xDC, 0xFC,
+ 0xC8, 0xE8, 0xD8, 0xF8, 0x4C, 0x6C, 0x5C, 0x7C,
+ 0xEC, 0xBC, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 2;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ size = 128;
+ page_size = 4;
+ num_pages = 32;
+ min_write_delay = 4000;
+ max_write_delay = 4000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read = "1 0 1 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 x x x x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 2048;
+ page_size = 32;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x x x x a9 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x x o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 1 i i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x x x o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+;
+
+
+#------------------------------------------------------------
+# ATtiny461
+#------------------------------------------------------------
+# Close to ATtiny261
+
+part
+ id = "t461";
+ desc = "ATTINY461";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x00, 0x10;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x00, 0xB4, 0x00, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+# stk500_devcode = 0x21;
+# avr910_devcode = 0x5e;
+ signature = 0x1e 0x92 0x08;
+ pagel = 0xb3;
+ bs2 = 0xb2;
+ chip_erase_delay = 4000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0xC4, 0xE4, 0xC4, 0xE4, 0xCC, 0xEC, 0xCC, 0xEC,
+ 0xD4, 0xF4, 0xD4, 0xF4, 0xDC, 0xFC, 0xDC, 0xFC,
+ 0xC8, 0xE8, 0xD8, 0xF8, 0x4C, 0x6C, 0x5C, 0x7C,
+ 0xEC, 0xBC, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 2;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ size = 256;
+ page_size = 4;
+ num_pages = 64;
+ min_write_delay = 4000;
+ max_write_delay = 4000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 4096;
+ page_size = 64;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x x o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 1 i i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x x x o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+;
+
+
+#------------------------------------------------------------
+# ATtiny861
+#------------------------------------------------------------
+# Close to ATtiny461
+
+part
+ id = "t861";
+ desc = "ATTINY861";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x00, 0x10;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x00, 0xB4, 0x00, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+# stk500_devcode = 0x21;
+# avr910_devcode = 0x5e;
+ signature = 0x1e 0x93 0x0d;
+ pagel = 0xb3;
+ bs2 = 0xb2;
+ chip_erase_delay = 4000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 0;
+
+ pp_controlstack =
+ 0xC4, 0xE4, 0xC4, 0xE4, 0xCC, 0xEC, 0xCC, 0xEC,
+ 0xD4, 0xF4, 0xD4, 0xF4, 0xDC, 0xFC, 0xDC, 0xFC,
+ 0xC8, 0xE8, 0xD8, 0xF8, 0x4C, 0x6C, 0x5C, 0x7C,
+ 0xEC, 0xBC, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 2;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ size = 512;
+ num_pages = 128;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read = " 1 0 1 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0 x x x x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 x x x x x x x x",
+ "x x x x x x x x x x x x x x o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 1 1 1 i i",
+ "x x x x x x x x x x x x x x x x";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x x x o";
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+;
+
+
+#------------------------------------------------------------
+# ATmega48
+#------------------------------------------------------------
+
+part
+ id = "m48";
+ desc = "ATMEGA48";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x59;
+# avr910_devcode = 0x;
+ signature = 0x1e 0x92 0x05;
+ pagel = 0xd7;
+ bs2 = 0xc2;
+ chip_erase_delay = 45000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ page_size = 4;
+ size = 256;
+ min_write_delay = 3600;
+ max_write_delay = 3600;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 5;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 4096;
+ page_size = 64;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x x x o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+
+#------------------------------------------------------------
+# ATmega88
+#------------------------------------------------------------
+
+part
+ id = "m88";
+ desc = "ATMEGA88";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x73;
+# avr910_devcode = 0x;
+ signature = 0x1e 0x93 0x0a;
+ pagel = 0xd7;
+ bs2 = 0xc2;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ page_size = 4;
+ size = 512;
+ min_write_delay = 3600;
+ max_write_delay = 3600;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 5;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega168
+#------------------------------------------------------------
+
+part
+ id = "m168";
+ desc = "ATMEGA168";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x86;
+ # avr910_devcode = 0x;
+ signature = 0x1e 0x94 0x06;
+ pagel = 0xd7;
+ bs2 = 0xc2;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ page_size = 4;
+ size = 512;
+ min_write_delay = 3600;
+ max_write_delay = 3600;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 5;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 16384;
+ page_size = 128;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+;
+
+#------------------------------------------------------------
+# ATmega328
+#------------------------------------------------------------
+
+part
+ id = "m328p";
+ desc = "ATMEGA328P";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x86;
+ # avr910_devcode = 0x;
+ signature = 0x1e 0x95 0x0F;
+ pagel = 0xd7;
+ bs2 = 0xc2;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ resetdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ paged = no;
+ page_size = 4;
+ size = 1024;
+ min_write_delay = 3600;
+ max_write_delay = 3600;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 5;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 a13 a12 a11 a10 a9 a8",
+ " a7 a6 x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 128;
+ readsize = 256;
+
+ ;
+
+ memory "lfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "hfuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+ ;
+
+ memory "efuse"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x x x x x x o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+ ;
+
+ memory "lock"
+ size = 1;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+;
+
+#------------------------------------------------------------
+# ATtiny2313
+#------------------------------------------------------------
+
+part
+ id = "t2313";
+ desc = "ATtiny2313";
+ has_debugwire = yes;
+ flash_instr = 0xB2, 0x0F, 0x1F;
+ eeprom_instr = 0xBB, 0xFE, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBA, 0x0F, 0xB2, 0x0F, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+ stk500_devcode = 0x23;
+## Use the ATtiny26 devcode:
+ avr910_devcode = 0x5e;
+ signature = 0x1e 0x91 0x0a;
+ pagel = 0xD4;
+ bs2 = 0xD6;
+ reset = io;
+ chip_erase_delay = 9000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0E, 0x1E, 0x2E, 0x3E, 0x2E, 0x3E,
+ 0x4E, 0x5E, 0x4E, 0x5E, 0x6E, 0x7E, 0x6E, 0x7E,
+ 0x26, 0x36, 0x66, 0x76, 0x2A, 0x3A, 0x6A, 0x7A,
+ 0x2E, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 128;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 2048;
+ page_size = 32;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+# The information in the data sheet of April/2004 is wrong, this works:
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+# The information in the data sheet of April/2004 is wrong, this works:
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+# The information in the data sheet of April/2004 is wrong, this works:
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny2313 has Signature Bytes: 0x1E 0x91 0x0A.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+# The Tiny2313 has calibration data for both 4 MHz and 8 MHz.
+# The information in the data sheet of April/2004 is wrong, this works:
+
+ memory "calibration"
+ size = 2;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90PWM2
+#------------------------------------------------------------
+
+part
+ id = "pwm2";
+ desc = "AT90PWM2";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x65;
+## avr910_devcode = ?;
+ signature = 0x1e 0x93 0x81;
+ pagel = 0xD8;
+ bs2 = 0xE2;
+ reset = io;
+ chip_erase_delay = 9000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+# AT90PWM2 has Signature Bytes: 0x1E 0x93 0x81.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90PWM3
+#------------------------------------------------------------
+
+# Completely identical to AT90PWM2 (including the signature!)
+
+part
+ id = "pwm3";
+ desc = "AT90PWM3";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x65;
+## avr910_devcode = ?;
+ signature = 0x1e 0x93 0x81;
+ pagel = 0xD8;
+ bs2 = 0xE2;
+ reset = io;
+ chip_erase_delay = 9000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+# AT90PWM2 has Signature Bytes: 0x1E 0x93 0x81.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90PWM2B
+#------------------------------------------------------------
+# Same as AT90PWM2 but different signature.
+
+part
+ id = "pwm2b";
+ desc = "AT90PWM2B";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x65;
+## avr910_devcode = ?;
+ signature = 0x1e 0x93 0x83;
+ pagel = 0xD8;
+ bs2 = 0xE2;
+ reset = io;
+ chip_erase_delay = 9000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90PWM3B
+#------------------------------------------------------------
+
+# Completely identical to AT90PWM2B (including the signature!)
+
+part
+ id = "pwm3b";
+ desc = "AT90PWM3B";
+ has_debugwire = yes;
+ flash_instr = 0xB6, 0x01, 0x11;
+ eeprom_instr = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+ 0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+ 0x99, 0xF9, 0xBB, 0xAF;
+ stk500_devcode = 0x65;
+## avr910_devcode = ?;
+ signature = 0x1e 0x93 0x83;
+ pagel = 0xD8;
+ bs2 = 0xE2;
+ reset = io;
+ chip_erase_delay = 9000;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 64;
+ readsize = 256;
+ ;
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny25
+#------------------------------------------------------------
+
+part
+ id = "t25";
+ desc = "ATtiny25";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x02, 0x12;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x02, 0xB4, 0x02, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+## no STK500 devcode in XML file, use the ATtiny45 one
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x91 0x08;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 128;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 2048;
+ page_size = 32;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny25 has Signature Bytes: 0x1E 0x91 0x08.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 2;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny45
+#------------------------------------------------------------
+
+part
+ id = "t45";
+ desc = "ATtiny45";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x02, 0x12;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x02, 0xB4, 0x02, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x92 0x06;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 256;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 4096;
+ page_size = 64;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny45 has Signature Bytes: 0x1E 0x92 0x08. (Data sheet 2586C-AVR-06/05 (doc2586.pdf) indicates otherwise!)
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 2;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny85
+#------------------------------------------------------------
+
+part
+ id = "t85";
+ desc = "ATtiny85";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x02, 0x12;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x02, 0xB4, 0x02, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+## no STK500 devcode in XML file, use the ATtiny45 one
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x93 0x0b;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x00;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a8 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny85 has Signature Bytes: 0x1E 0x93 0x08.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 2;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega640
+#------------------------------------------------------------
+# Almost same as ATmega1280, except for different memory sizes
+
+part
+ id = "m640";
+ desc = "ATMEGA640";
+ signature = 0x1e 0x96 0x08;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega1280
+#------------------------------------------------------------
+
+part
+ id = "m1280";
+ desc = "ATMEGA1280";
+ signature = 0x1e 0x97 0x03;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega1281
+#------------------------------------------------------------
+# Identical to ATmega1280
+
+part
+ id = "m1281";
+ desc = "ATMEGA1281";
+ signature = 0x1e 0x97 0x04;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega2560
+#------------------------------------------------------------
+
+part
+ id = "m2560";
+ desc = "ATMEGA2560";
+ signature = 0x1e 0x98 0x01;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 262144;
+ page_size = 256;
+ num_pages = 1024;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ load_ext_addr = " 0 1 0 0 1 1 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 a16",
+ " 0 0 0 0 0 0 0 0";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega2561
+#------------------------------------------------------------
+
+part
+ id = "m2561";
+ desc = "ATMEGA2561";
+ signature = 0x1e 0x98 0x02;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 262144;
+ page_size = 256;
+ num_pages = 1024;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ load_ext_addr = " 0 1 0 0 1 1 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 a16",
+ " 0 0 0 0 0 0 0 0";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny24
+#------------------------------------------------------------
+
+part
+ id = "t24";
+ desc = "ATtiny24";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x07, 0x17;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x07, 0xB4, 0x07, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+## no STK500 devcode in XML file, use the ATtiny45 one
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x91 0x0b;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0F;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 70;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 128;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "x a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 2048;
+ page_size = 32;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x x a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny24 has Signature Bytes: 0x1E 0x91 0x0B.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x x x x x x x i i";
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny44
+#------------------------------------------------------------
+
+part
+ id = "t44";
+ desc = "ATtiny44";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x07, 0x17;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x07, 0xB4, 0x07, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+## no STK500 devcode in XML file, use the ATtiny45 one
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x92 0x07;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0F;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 70;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 256;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x x",
+ "a7 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 4096;
+ page_size = 64;
+ num_pages = 64;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny44 has Signature Bytes: 0x1E 0x92 0x07.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x x x x x x x i i";
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATtiny84
+#------------------------------------------------------------
+
+part
+ id = "t84";
+ desc = "ATtiny84";
+ has_debugwire = yes;
+ flash_instr = 0xB4, 0x07, 0x17;
+ eeprom_instr = 0xBB, 0xFF, 0xBB, 0xEE, 0xBB, 0xCC, 0xB2, 0x0D,
+ 0xBC, 0x07, 0xB4, 0x07, 0xBA, 0x0D, 0xBB, 0xBC,
+ 0x99, 0xE1, 0xBB, 0xAC;
+## no STK500 devcode in XML file, use the ATtiny45 one
+ stk500_devcode = 0x14;
+## avr910_devcode = ?;
+## Try the AT90S2313 devcode:
+ avr910_devcode = 0x20;
+ signature = 0x1e 0x93 0x0c;
+ reset = io;
+ chip_erase_delay = 4500;
+
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ hvsp_controlstack =
+ 0x4C, 0x0C, 0x1C, 0x2C, 0x3C, 0x64, 0x74, 0x66,
+ 0x68, 0x78, 0x68, 0x68, 0x7A, 0x6A, 0x68, 0x78,
+ 0x78, 0x7D, 0x6D, 0x0C, 0x80, 0x40, 0x20, 0x10,
+ 0x11, 0x08, 0x04, 0x02, 0x03, 0x08, 0x04, 0x0F;
+ hventerstabdelay = 100;
+ hvspcmdexedelay = 0;
+ synchcycles = 6;
+ latchcycles = 1;
+ togglevtg = 1;
+ poweroffdelay = 25;
+ resetdelayms = 0;
+ resetdelayus = 70;
+ hvleavestabdelay = 100;
+ resetdelay = 25;
+ chiperasepolltimeout = 40;
+ chiperasetime = 0;
+ programfusepolltimeout = 25;
+ programlockpolltimeout = 25;
+
+ memory "eeprom"
+ size = 512;
+ paged = no;
+ page_size = 4;
+ min_write_delay = 4000;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = "1 0 1 0 0 0 0 0 0 0 0 x x x x a8",
+ "a7 a6 a5 a4 a3 a2 a1 a0 o o o o o o o o";
+
+ write = "1 1 0 0 0 0 0 0 0 0 0 x x x x a8",
+ "a8 a6 a5 a4 a3 a2 a1 a0 i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x x x x",
+ " x a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 4;
+ readsize = 256;
+ ;
+ memory "flash"
+ paged = yes;
+ size = 8192;
+ page_size = 64;
+ num_pages = 128;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 x x x x x",
+ " x x x a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 0 0 0 a11 a10 a9 a8",
+ " a7 a6 a5 x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 32;
+ readsize = 256;
+ ;
+# ATtiny84 has Signature Bytes: 0x1E 0x93 0x0C.
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+
+ memory "lock"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x x x x x x x i i";
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x x x x i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+ "0 0 0 0 0 0 0 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90USB646
+#------------------------------------------------------------
+
+part
+ id = "usb646";
+ desc = "AT90USB646";
+# signature = 0x1e 0x96 0x82; ?
+ signature = 0x1e 0x97 0x82;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90USB647
+#------------------------------------------------------------
+# identical to AT90USB646
+
+part
+ id = "usb647";
+ desc = "AT90USB647";
+# signature = 0x1e 0x96 0x82; ?
+ signature = 0x1e 0x97 0x82;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90USB1286
+#------------------------------------------------------------
+
+part
+ id = "usb1286";
+ desc = "AT90USB1286";
+ signature = 0x1e 0x97 0x82;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# AT90USB1287
+#------------------------------------------------------------
+# identical to AT90USB1286
+
+part
+ id = "usb1287";
+ desc = "AT90USB1287";
+ signature = 0x1e 0x97 0x82;
+ has_jtag = yes;
+# stk500_devcode = 0xB2;
+# avr910_devcode = 0x43;
+ chip_erase_delay = 9000;
+ pagel = 0xD7;
+ bs2 = 0xA0;
+ reset = dedicated;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "x x x x x x x x x x x x x x x x";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "x x x x x x x x x x x x x x x x";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ rampz = 0x3b;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 4096;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read = " 1 0 1 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " x x x x a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 x x x a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 131072;
+ page_size = 256;
+ num_pages = 512;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0x00;
+ readback_p2 = 0x00;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " x x x x x x x x",
+ " x a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ "a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 x x x x x x x",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 6;
+ blocksize = 256;
+ readsize = 256;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "x x x x x x x x i i i i i i i i";
+
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "x x x x x x x x x x x x i i i i";
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "x x x x x x x x o o o o o o o o";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+ "x x x x x x x x 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "calibration"
+ size = 1;
+ read = "0 0 1 1 1 0 0 0 x x x x x x x x",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 x x x x x x x x",
+ "x x x x x x a1 a0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega325
+#------------------------------------------------------------
+
+part
+ id = "m325";
+ desc = "ATMEGA325";
+ signature = 0x1e 0x95 0x05;
+ has_jtag = yes;
+# stk500_devcode = 0x??; # No STK500v1 support?
+# avr910_devcode = 0x??; # Try the ATmega16 one
+ avr910_devcode = 0x74;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "0 0 0 0 0 0 0 0 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega645
+#------------------------------------------------------------
+
+part
+ id = "m645";
+ desc = "ATMEGA645";
+ signature = 0x1E 0x96 0x05;
+ has_jtag = yes;
+# stk500_devcode = 0x??; # No STK500v1 support?
+# avr910_devcode = 0x??; # Try the ATmega16 one
+ avr910_devcode = 0x74;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 8;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " 0 0 0 0 0 0 0 0";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "0 0 0 0 0 0 0 0 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega3250
+#------------------------------------------------------------
+
+part
+ id = "m3250";
+ desc = "ATMEGA3250";
+ signature = 0x1E 0x95 0x06;
+ has_jtag = yes;
+# stk500_devcode = 0x??; # No STK500v1 support?
+# avr910_devcode = 0x??; # Try the ATmega16 one
+ avr910_devcode = 0x74;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 4; /* for parallel programming */
+ size = 1024;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 0 0 0 0 a9 a8",
+ " a7 a6 a5 a4 a3 a2 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 32768;
+ page_size = 128;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " 0 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "0 0 0 0 0 0 0 0 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
+
+#------------------------------------------------------------
+# ATmega6450
+#------------------------------------------------------------
+
+part
+ id = "m6450";
+ desc = "ATMEGA6450";
+ signature = 0x1E 0x96 0x06;
+ has_jtag = yes;
+# stk500_devcode = 0x??; # No STK500v1 support?
+# avr910_devcode = 0x??; # Try the ATmega16 one
+ avr910_devcode = 0x74;
+ pagel = 0xd7;
+ bs2 = 0xa0;
+ chip_erase_delay = 9000;
+ pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ chip_erase = "1 0 1 0 1 1 0 0 1 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0";
+
+ timeout = 200;
+ stabdelay = 100;
+ cmdexedelay = 25;
+ synchloops = 32;
+ bytedelay = 0;
+ pollindex = 3;
+ pollvalue = 0x53;
+ predelay = 1;
+ postdelay = 1;
+ pollmethod = 1;
+
+ pp_controlstack =
+ 0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+ 0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+ 0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+ 0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+ hventerstabdelay = 100;
+ progmodedelay = 0;
+ latchcycles = 5;
+ togglevtg = 1;
+ poweroffdelay = 15;
+ resetdelayms = 1;
+ resetdelayus = 0;
+ hvleavestabdelay = 15;
+ chiperasepulsewidth = 0;
+ chiperasepolltimeout = 10;
+ programfusepulsewidth = 0;
+ programfusepolltimeout = 5;
+ programlockpulsewidth = 0;
+ programlockpolltimeout = 5;
+
+ idr = 0x31;
+ spmcr = 0x57;
+ allowfullpagebitstream = no;
+
+ memory "eeprom"
+ paged = no; /* leave this "no" */
+ page_size = 8; /* for parallel programming */
+ size = 2048;
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read = " 1 0 1 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ write = " 1 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_lo = " 1 1 0 0 0 0 0 1",
+ " 0 0 0 0 0 0 0 0",
+ " 0 0 0 0 0 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 1 1 0 0 0 0 1 0",
+ " 0 0 0 0 0 a10 a9 a8",
+ " a7 a6 a5 a4 a3 0 0 0",
+ " x x x x x x x x";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 4;
+ readsize = 256;
+ ;
+
+ memory "flash"
+ paged = yes;
+ size = 65536;
+ page_size = 256;
+ num_pages = 256;
+ min_write_delay = 4500;
+ max_write_delay = 4500;
+ readback_p1 = 0xff;
+ readback_p2 = 0xff;
+ read_lo = " 0 0 1 0 0 0 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ read_hi = " 0 0 1 0 1 0 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " o o o o o o o o";
+
+ loadpage_lo = " 0 1 0 0 0 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ loadpage_hi = " 0 1 0 0 1 0 0 0",
+ " 0 0 0 0 0 0 0 0",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " i i i i i i i i";
+
+ writepage = " 0 1 0 0 1 1 0 0",
+ " a15 a14 a13 a12 a11 a10 a9 a8",
+ " a7 a6 a5 a4 a3 a2 a1 a0",
+ " 0 0 0 0 0 0 0 0";
+
+ mode = 0x41;
+ delay = 10;
+ blocksize = 128;
+ readsize = 256;
+ ;
+
+ memory "lock"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "x x x x x x x x x x o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 1 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 1 1 i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "lfuse"
+ size = 1;
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "hfuse"
+ size = 1;
+ read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 i i i i i i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "efuse"
+ size = 1;
+
+ read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+
+ write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+ "0 0 0 0 0 0 0 0 1 1 1 1 1 i i i";
+ min_write_delay = 9000;
+ max_write_delay = 9000;
+ ;
+
+ memory "signature"
+ size = 3;
+ read = "0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 a1 a0 o o o o o o o o";
+ ;
+
+ memory "calibration"
+ size = 1;
+
+ read = "0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0",
+ "0 0 0 0 0 0 0 0 o o o o o o o o";
+ ;
+ ;
diff --git a/Marlin/pins.h b/Marlin/pins.h
index f7c3e292a43..ce21a9ade21 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -567,6 +567,180 @@
#endif
+/****************************************************************************************
+* Gen7 v1.1, v1.2, v1.3 pin assignment
+*
+****************************************************************************************/
+
+#if MOTHERBOARD == 79
+#define MOTHERBOARD 78
+#define GEN7_V_1_3
+#endif
+
+#if MOTHERBOARD == 78
+#define KNOWN_BOARD
+
+#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
+#error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
+
+#endif
+
+//x axis pins
+#define X_STEP_PIN 19
+#define X_DIR_PIN 18
+#define X_ENABLE_PIN 24
+#define X_MIN_PIN 7
+#define X_MAX_PIN -1
+
+//y axis pins
+#define Y_STEP_PIN 23
+#define Y_DIR_PIN 22
+#define Y_ENABLE_PIN 24
+#define Y_MIN_PIN 5
+#define Y_MAX_PIN -1
+
+//z axis pins
+#define Z_STEP_PIN 26
+#define Z_DIR_PIN 25
+#define Z_ENABLE_PIN 24
+#define Z_MIN_PIN 1
+#define Z_MAX_PIN -1
+
+//extruder pins
+#define E0_STEP_PIN 28
+#define E0_DIR_PIN 27
+#define E0_ENABLE_PIN 24
+
+#define TEMP_0_PIN 1
+#define TEMP_1_PIN -1
+#define TEMP_2_PIN -1
+#define TEMP_BED_PIN 2
+
+#define HEATER_0_PIN 4
+#define HEATER_1_PIN -1
+#define HEATER_2_PIN -1
+#define HEATER_BED_PIN 3
+
+
+#define SDPOWER -1
+#define SDSS -1 // SCL pin of I2C header
+#define LED_PIN -1
+
+#ifdef GEN7_V_1_3
+// Gen7 v1.3 removed the fan pin
+#define FAN_PIN -1
+#else
+#define FAN_PIN 31
+#endif
+#define PS_ON_PIN 15
+
+//our pin for debugging.
+#define DEBUG_PIN 0
+
+//our RS485 pins
+#define TX_ENABLE_PIN 12
+#define RX_ENABLE_PIN 13
+
+#endif
+
+/*******************************************************************************
+*********
+* Gen7 Alfons3 pin assignment
+*
+********************************************************************************
+********/
+/* These Pins are assigned for the modified GEN7 Board from Alfons3 Please review the pins and adjust it for your needs*/
+
+#if MOTHERBOARD == 77
+#define KNOWN_BOARD
+
+#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
+ #error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
+
+#endif
+
+//x axis pins
+ #define X_STEP_PIN 21 //different from stanard GEN7
+ #define X_DIR_PIN 20 //different from stanard GEN7
+ #define X_ENABLE_PIN 24
+ #define X_MIN_PIN 0
+ #define X_MAX_PIN -1
+
+ //y axis pins
+ #define Y_STEP_PIN 23
+ #define Y_DIR_PIN 22
+ #define Y_ENABLE_PIN 24
+ #define Y_MIN_PIN 1
+ #define Y_MAX_PIN -1
+
+ //z axis pins
+ #define Z_STEP_PIN 26
+ #define Z_DIR_PIN 25
+ #define Z_ENABLE_PIN 24
+ #define Z_MIN_PIN 2
+ #define Z_MAX_PIN -1
+
+ //extruder pins
+ #define E0_STEP_PIN 28
+ #define E0_DIR_PIN 27
+ #define E0_ENABLE_PIN 24
+
+ #define TEMP_0_PIN 2
+ #define TEMP_1_PIN -1
+ #define TEMP_2_PIN -1
+ #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
+
+ #define HEATER_0_PIN 4
+ #define HEATER_1_PIN -1
+ #define HEATER_2_PIN -1
+ #define HEATER_BED_PIN 3 // (bed)
+
+
+
+
+ #define SDPOWER -1
+ #define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
+ #define LED_PIN -1
+
+ #define FAN_PIN -1
+ #define PS_ON_PIN 19
+ //our pin for debugging.
+
+ #define DEBUG_PIN -1
+
+ //our RS485 pins
+ //#define TX_ENABLE_PIN 12
+ //#define RX_ENABLE_PIN 13
+
+ #define BEEPER -1
+ #define SDCARDDETECT -1
+ #define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work
+
+ //Pins for 4bit LCD Support
+ #define LCD_PINS_RS 18
+ #define LCD_PINS_ENABLE 17
+ #define LCD_PINS_D4 16
+ #define LCD_PINS_D5 15
+ #define LCD_PINS_D6 13
+ #define LCD_PINS_D7 14
+
+ //buttons are directly attached
+ #define BTN_EN1 11
+ #define BTN_EN2 10
+ #define BTN_ENC 12 //the click
+
+ #define BLEN_C 2
+ #define BLEN_B 1
+ #define BLEN_A 0
+
+
+ #define encrot0 0
+ #define encrot1 2
+ #define encrot2 3
+ #define encrot3 1
+
+
+#endif
#if MOTHERBOARD == 7
#define KNOWN_BOARD
diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp
index 2f3888c0187..95f0f867486 100644
--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@@ -851,13 +851,21 @@ ISR(TIMER0_COMPB_vect)
for(unsigned char e = 0; e < EXTRUDERS; e++) {
if(current_raw[e] >= maxttemp[e]) {
target_raw[e] = 0;
- max_temp_error(e);
- kill();;
+ #if (PS_ON != -1)
+ {
+ max_temp_error(e);
+ kill();;
+ }
+ #endif
}
if(current_raw[e] <= minttemp[e]) {
target_raw[e] = 0;
- min_temp_error(e);
- kill();
+ #if (PS_ON != -1)
+ {
+ min_temp_error(e);
+ kill();
+ }
+ #endif
}
}
diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h
index 08ac950d38e..db8a1318364 100644
--- a/Marlin/ultralcd.h
+++ b/Marlin/ultralcd.h
@@ -27,7 +27,11 @@
#define CLICKED (buttons&EN_C)
#define BLOCK {blocking=millis()+blocktime;}
- #define CARDINSERTED (READ(SDCARDDETECT)==0)
+ #if (SDCARDDETECT > -1)
+ {
+ #define CARDINSERTED (READ(SDCARDDETECT)==0)
+ }
+ #endif
#else
@@ -50,7 +54,7 @@
#define blocktime 500
#define lcdslow 5
- enum MainStatus{Main_Status, Main_Menu, Main_Prepare, Main_Control, Main_SD,Sub_TempControl,Sub_MotionControl};
+ enum MainStatus{Main_Status, Main_Menu, Main_Prepare,Sub_PrepareMove, Main_Control, Main_SD,Sub_TempControl,Sub_MotionControl};
class MainMenu{
public:
@@ -67,6 +71,7 @@
void showControl();
void showControlMotion();
void showControlTemp();
+ void showAxisMove();
void showSD();
bool force_lcd_update;
int lastencoderpos;
diff --git a/Marlin/ultralcd.pde b/Marlin/ultralcd.pde
index 68a59547524..32ef2f3b873 100644
--- a/Marlin/ultralcd.pde
+++ b/Marlin/ultralcd.pde
@@ -130,13 +130,17 @@ void beep()
{
//return;
#ifdef ULTIPANEL
- pinMode(BEEPER,OUTPUT);
- for(int8_t i=0;i<20;i++){
- WRITE(BEEPER,HIGH);
- delay(5);
- WRITE(BEEPER,LOW);
- delay(5);
- }
+ #if (BEEPER > -1)
+ {
+ pinMode(BEEPER,OUTPUT);
+ for(int8_t i=0;i<20;i++){
+ WRITE(BEEPER,HIGH);
+ delay(5);
+ WRITE(BEEPER,LOW);
+ delay(5);
+ }
+ }
+ #endif
#endif
}
@@ -144,13 +148,17 @@ void beepshort()
{
//return;
#ifdef ULTIPANEL
- pinMode(BEEPER,OUTPUT);
- for(int8_t i=0;i<10;i++){
- WRITE(BEEPER,HIGH);
- delay(3);
- WRITE(BEEPER,LOW);
- delay(3);
- }
+ #if (BEEPER > -1)
+ {
+ pinMode(BEEPER,OUTPUT);
+ for(int8_t i=0;i<10;i++){
+ WRITE(BEEPER,HIGH);
+ delay(3);
+ WRITE(BEEPER,LOW);
+ delay(3);
+ }
+ }
+ #endif
#endif
}
@@ -197,7 +205,11 @@ void buttons_init()
WRITE(BTN_EN1,HIGH);
WRITE(BTN_EN2,HIGH);
WRITE(BTN_ENC,HIGH);
- WRITE(SDCARDDETECT,HIGH);
+ #if (SDCARDDETECT > -1)
+ {
+ WRITE(SDCARDDETECT,HIGH);
+ }
+ #endif
#else
pinMode(SHIFT_CLK,OUTPUT);
pinMode(SHIFT_LD,OUTPUT);
@@ -445,7 +457,7 @@ void MainMenu::showStatus()
force_lcd_update=false;
}
-enum {ItemP_exit, ItemP_autostart,ItemP_disstep,ItemP_home, ItemP_origin, ItemP_preheat, ItemP_cooldown,ItemP_extrude};
+enum {ItemP_exit, ItemP_autostart,ItemP_disstep,ItemP_home, ItemP_origin, ItemP_preheat, ItemP_cooldown,/*ItemP_extrude,*/ItemP_move};
//any action must not contain a ',' character anywhere, or this breaks:
#define MENUITEM(repaint_action, click_action) \
@@ -473,28 +485,193 @@ void MainMenu::showPrepare()
MENUITEM( lcdprintPGM(" Disable Steppers") , BLOCK;enquecommand("M84");beepshort(); ) ;
break;
case ItemP_home:
- MENUITEM( lcdprintPGM(" Auto Home") , BLOCK;enquecommand("G28 X-105 Y-105 Z0");beepshort(); ) ;
+ MENUITEM( lcdprintPGM(" Auto Home") , BLOCK;enquecommand("G28 X0 Y0 Z0");beepshort(); ) ;
break;
case ItemP_origin:
MENUITEM( lcdprintPGM(" Set Origin") , BLOCK;enquecommand("G92 X0 Y0 Z0");beepshort(); ) ;
break;
case ItemP_preheat:
- MENUITEM( lcdprintPGM(" Preheat") , BLOCK;setTargetHotend0(170);setTargetBed(70);beepshort(); ) ;
+ MENUITEM( lcdprintPGM(" Preheat") , BLOCK;setTargetHotend0(227);setTargetBed(105);beepshort(); ) ;
break;
case ItemP_cooldown:
MENUITEM( lcdprintPGM(" Cooldown") , BLOCK;setTargetHotend0(0);setTargetBed(0);beepshort(); ) ;
break;
- case ItemP_extrude:
- MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E50");beepshort(); ) ;
+// case ItemP_extrude:
+ // MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E50");beepshort(); ) ;
+ // break;
+ case ItemP_move:
+ MENUITEM( lcdprintPGM(" Move Axis \x7E") , BLOCK;status=Sub_PrepareMove;beepshort(); );
break;
-
-
- default:
+ default:
break;
}
line++;
}
- updateActiveLines(ItemP_extrude,encoderpos);
+ updateActiveLines(ItemP_move,encoderpos);
+}
+
+enum {
+ ItemAM_exit,
+ ItemAM_X, ItemAM_Y, ItemAM_Z, ItemAM_E
+};
+
+void MainMenu::showAxisMove()
+{
+ uint8_t line=0;
+ int oldencoderpos=0;
+ clearIfNecessary();
+ for(int8_t i=lineoffset;i<lineoffset+LCD_HEIGHT;i++)
+ {
+ switch(i)
+ {
+ case ItemAM_exit:
+ MENUITEM( lcdprintPGM(" Prepare \003") , BLOCK;status=Main_Menu;beepshort(); ) ;
+ break;
+ case ItemAM_X:
+ {
+ //oldencoderpos=0;
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" X:");
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[X_AXIS]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ enquecommand("G91");
+ }
+ else
+ {
+ enquecommand("G90");
+ encoderpos=activeline*lcdslow;
+ beepshort();
+ }
+ BLOCK;
+ }
+ if(linechanging)
+ {
+ if (encoderpos >0)
+ {
+ enquecommand("G1 F700 X0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+
+ else if (encoderpos < 0)
+ {
+ enquecommand("G1 F700 X-0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[X_AXIS]));
+ }
+ }
+ break;
+ case ItemAM_Y:
+ {
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" Y:");
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[Y_AXIS]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ enquecommand("G91");
+ }
+ else
+ {
+ enquecommand("G90");
+ encoderpos=activeline*lcdslow;
+ beepshort();
+ }
+ BLOCK;
+ }
+ if(linechanging)
+ {
+ if (encoderpos >0)
+ {
+ enquecommand("G1 F700 Y0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+
+ else if (encoderpos < 0)
+ {
+ enquecommand("G1 F700 Y-0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[Y_AXIS]));
+ }
+ }
+ break;
+ case ItemAM_Z:
+ {
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" Z:");
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[Z_AXIS]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ enquecommand("G91");
+ }
+ else
+ {
+ enquecommand("G90");
+ encoderpos=activeline*lcdslow;
+ beepshort();
+ }
+ BLOCK;
+ }
+ if(linechanging)
+ {
+ if (encoderpos >0)
+ {
+ enquecommand("G1 F170 Z0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+
+ else if (encoderpos < 0)
+ {
+ enquecommand("G1 F1700 Z-0.1");
+ oldencoderpos=encoderpos;
+ encoderpos=0;
+ }
+ lcd.setCursor(13,line);lcd.print(ftostr32(current_position[Z_AXIS]));
+ }
+ }
+ break;
+ case ItemAM_E:
+ MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E5");beepshort(); ) ;
+ break;
+ default:
+ break;
+ }
+ line++;
+ }
+ updateActiveLines(ItemAM_E,encoderpos);
}
enum {ItemT_exit,ItemT_speed,ItemT_flow,ItemT_nozzle,
@@ -1140,7 +1317,7 @@ enum {
ItemCM_vmaxx, ItemCM_vmaxy, ItemCM_vmaxz, ItemCM_vmaxe,
ItemCM_vtravmin,ItemCM_vmin,
ItemCM_amaxx, ItemCM_amaxy, ItemCM_amaxz, ItemCM_amaxe,
- ItemCM_aret,ItemCM_esteps
+ ItemCM_aret, ItemCM_xsteps,ItemCM_ysteps, ItemCM_zsteps, ItemCM_esteps
};
@@ -1416,11 +1593,126 @@ void MainMenu::showControlMotion()
}
}break;
+ case ItemCM_xsteps://axis_steps_per_unit[i] = code_value();
+ {
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" X steps/mm:");
+ lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[0]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ encoderpos=(int)axis_steps_per_unit[0];
+ }
+ else
+ {
+ float factor=float(encoderpos)/float(axis_steps_per_unit[0]);
+ position[X_AXIS]=lround(position[X_AXIS]*factor);
+ //current_position[3]*=factor;
+ axis_steps_per_unit[X_AXIS]= encoderpos;
+ encoderpos=activeline*lcdslow;
+
+ }
+ BLOCK;
+ beepshort();
+ }
+ if(linechanging)
+ {
+ if(encoderpos<5) encoderpos=5;
+ if(encoderpos>9999) encoderpos=9999;
+ lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
+ }
+
+ }break;
+ case ItemCM_ysteps://axis_steps_per_unit[i] = code_value();
+ {
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" Y steps/mm:");
+ lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[1]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ encoderpos=(int)axis_steps_per_unit[1];
+ }
+ else
+ {
+ float factor=float(encoderpos)/float(axis_steps_per_unit[1]);
+ position[Y_AXIS]=lround(position[Y_AXIS]*factor);
+ //current_position[3]*=factor;
+ axis_steps_per_unit[Y_AXIS]= encoderpos;
+ encoderpos=activeline*lcdslow;
+
+ }
+ BLOCK;
+ beepshort();
+ }
+ if(linechanging)
+ {
+ if(encoderpos<5) encoderpos=5;
+ if(encoderpos>9999) encoderpos=9999;
+ lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
+ }
+
+ }break;
+ case ItemCM_zsteps://axis_steps_per_unit[i] = code_value();
+ {
+ if(force_lcd_update)
+ {
+ lcd.setCursor(0,line);lcdprintPGM(" Z steps/mm:");
+ lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[2]));
+ }
+
+ if((activeline!=line) )
+ break;
+
+ if(CLICKED)
+ {
+ linechanging=!linechanging;
+ if(linechanging)
+ {
+ encoderpos=(int)axis_steps_per_unit[2];
+ }
+ else
+ {
+ float factor=float(encoderpos)/float(axis_steps_per_unit[2]);
+ position[Z_AXIS]=lround(position[Z_AXIS]*factor);
+ //current_position[3]*=factor;
+ axis_steps_per_unit[Z_AXIS]= encoderpos;
+ encoderpos=activeline*lcdslow;
+
+ }
+ BLOCK;
+ beepshort();
+ }
+ if(linechanging)
+ {
+ if(encoderpos<5) encoderpos=5;
+ if(encoderpos>9999) encoderpos=9999;
+ lcd.setCursor(13,line);lcd.print(itostr4(encoderpos));
+ }
+
+ }break;
+
case ItemCM_esteps://axis_steps_per_unit[i] = code_value();
{
if(force_lcd_update)
{
- lcd.setCursor(0,line);lcdprintPGM(" Esteps/mm:");
+ lcd.setCursor(0,line);lcdprintPGM(" E steps/mm:");
lcd.setCursor(13,line);lcd.print(itostr4(axis_steps_per_unit[3]));
}
@@ -1636,7 +1928,7 @@ void MainMenu::showSD()
status=Main_Status;
lcd_status(card.filename);
}
- }
+ }
}
}
@@ -1801,6 +2093,10 @@ void MainMenu::update()
showPrepare();
}
}break;
+ case Sub_PrepareMove:
+ {
+ showAxisMove();
+ }break;
case Main_Control:
{
showControl();
diff --git a/README b/README
deleted file mode 100644
index 2487d4875d7..00000000000
--- a/README
+++ /dev/null
@@ -1,64 +0,0 @@
-This RepRap firmware is a mashup between Sprinter, grbl and many original parts.
- (https://github.com/kliment/Sprinter)
- (https://github.com/simen/grbl/tree)
-
-Derived from Sprinter and Grbl by Erik van der Zalm.
-Sprinters lead developers are Kliment and caru.
-Grbls lead developer is Simen Svale Skogsrud.
-It has been adapted to the Ultimaker Printer by:
-Bernhard Kubicek, Matthijs Keuper, Bradley Feldman, and others...
-
-
-Features:
- - Interrupt based movement with real linear acceleration
- - High steprate
- - Look ahead (Keep the speed high when possible. High cornering speed)
- - Interrupt based temperature protection
- - preliminary support for Matthew Roberts advance algorithm
- For more info see: http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
- - Full endstop support
- - Simple LCD support (16x2)
- - SD Card support
- - Provisions for Bernhard Kubicek's new hardware control console and 20x4 lcd
-
-This firmware is optimized for Ultimaker's gen6 electronics (including the Ultimaker 1.5.x daughterboard and Arduino Mega 2560).
-
-The default baudrate is 115200.
-
-
-========================================================================================
-
-Configuring and compilation
-
-
-Install the latest arduino software IDE/toolset (currently 0022)
- http://www.arduino.cc/en/Main/Software
-
-Install Ultimaker's RepG 25 build
- http://software.ultimaker.com
-(or alternatively install Kliment's printrun/pronterface https://github.com/kliment/Printrun_)
-
-Copy the Ultimaker Marlin firmware
- https:/github.com/bkubicek/Marlin
- (Use the download button)
-
-Start the arduino IDE.
-Select Tools -> Board -> Arduino Mega 2560
-Select the correct serial port in Tools ->Serial Port
-Open Marlin.pde
-
-Click the Verify/Compile button
-
-Click the Upload button
-If all goes well the firmware is uploading
-
-Start Ultimaker's Custom RepG 25
-Make sure Show Experimental Profiles is enabled in Preferences
-Select Sprinter as the Driver
-
-Press the Connect button.
-
-KNOWN ISSUES: RepG will display: Unknown: marlin x.y.z
-
-That's ok. Enjoy Silky Smooth Printing.
-
diff --git a/README.md b/README.md
index 6f04764c94e..11b4be60f01 100644
--- a/README.md
+++ b/README.md
@@ -1,3 +1,23 @@
+SCUBA82's fork:
+-----------------
+
+The main goal of my fork is porting the brilliant Marlin firmware to GEN7 Boards.
+I'm working on a 16MHz GEN7 board and have only tested with this configuration.
+But there were reports about successfully running it at 20 MHz. Expect 25% faster moves and maybe some other issues.
+
+Using lcd and sdcard support on an ATMega644(P) is not possible cause the sketch is way too big for its memory.
+I switched to an ATMega1284P which has double size program memory. Unfortunately it's not supported in Arduino IDE out of the box but expect a tutorial on how to compile for it soon.
+For the necessary pin breakouts I used Alfons3 design of GEN7 (https://github.com/Alfons3/Generation_7_Electronics) with an additional breakout for pin A0/D31.
+I'll publish my desing as soon as possible.
+
+You have to use different chip fuses to get Marlin running.
+The fuses I'm using are lfuse: 0xF7 hfuse: 0xD4 efuse: 0xFD
+
+For questions take a look into http://forums.reprap.org/read.php?181,118329 or send me an e-mail: christian_thalhammer@gmx.at
+
+
+Expect this fork to be highly experimental.
+
WARNING:
--------
THIS IS RELEASE CANDIDATE 1 FOR MARLIN 1.0.0