✨ Add TEMP_SENSOR_BOARD (#22279)

Marlin/Configuration.h

@@ -474,7 +474,7 @@
  *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
  *
- *  Custom/Dummy/Other Thermos
+ *  Custom/Dummy/Other Thermal Sensors
  *  ------
  *     0 : not used
  *  1000 : Custom - Specify parameters in Configuration_adv.h
@@ -496,6 +496,7 @@
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
+#define TEMP_SENSOR_BOARD 0
 #define TEMP_SENSOR_REDUNDANT 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -528,17 +529,11 @@
  * the print will be aborted. Whichever sensor is selected will have its normal functions disabled; i.e. selecting
  * the Bed sensor (-1) will disable bed heating/monitoring.
  *
- * Use the following to select temp sensors:
+ * For selecting source/target use: COOLER, PROBE, BOARD, CHAMBER, BED, E0, E1, E2, E3, E4, E5, E6, E7
- *    -5 : Cooler
- *    -4 : Probe
- *    -3 : not used
- *    -2 : Chamber
- *    -1 : Bed
- *   0-7 : E0 through E7
  */
 #if TEMP_SENSOR_REDUNDANT
-  #define TEMP_SENSOR_REDUNDANT_SOURCE     1  // The sensor that will provide the redundant reading.
+  #define TEMP_SENSOR_REDUNDANT_SOURCE    E1  // The sensor that will provide the redundant reading.
-  #define TEMP_SENSOR_REDUNDANT_TARGET     0  // The sensor that we are providing a redundant reading for.
+  #define TEMP_SENSOR_REDUNDANT_TARGET    E0  // The sensor that we are providing a redundant reading for.
   #define TEMP_SENSOR_REDUNDANT_MAX_DIFF  10  // (°C) Temperature difference that will trigger a print abort.
 #endif
 

Marlin/Configuration_adv.h

@@ -125,6 +125,12 @@
   #define PROBE_BETA                   3950    // Beta value
 #endif
 
+#if TEMP_SENSOR_BOARD == 1000
+  #define BOARD_PULLUP_RESISTOR_OHMS   4700    // Pullup resistor
+  #define BOARD_RESISTANCE_25C_OHMS    100000  // Resistance at 25C
+  #define BOARD_BETA                   3950    // Beta value
+#endif
+
 #if TEMP_SENSOR_REDUNDANT == 1000
   #define REDUNDANT_PULLUP_RESISTOR_OHMS   4700    // Pullup resistor
   #define REDUNDANT_RESISTANCE_25C_OHMS    100000  // Resistance at 25C
@@ -224,6 +230,18 @@
   #endif
 #endif
 
+//
+// Motherboard Sensor options
+//
+#if TEMP_SENSOR_BOARD
+  #define THERMAL_PROTECTION_BOARD   // Halt the printer if the board sensor leaves the temp range below.
+  #define BOARD_MINTEMP           8  // (°C)
+  #define BOARD_MAXTEMP          70  // (°C)
+  #ifndef TEMP_BOARD_PIN
+    //#define TEMP_BOARD_PIN -1      // Board temp sensor pin, if not set in pins file.
+  #endif
+#endif
+
 //
 // Laser Coolant Flow Meter
 //
@@ -487,6 +505,10 @@
   #define CONTROLLERFAN_SPEED_ACTIVE    255 // (0-255) Active speed, used when any motor is enabled
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
+
+  // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
+  //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
+
   //#define CONTROLLER_FAN_EDITABLE         // Enable M710 configurable settings
   #if ENABLED(CONTROLLER_FAN_EDITABLE)
     #define CONTROLLER_FAN_MENU             // Enable the Controller Fan submenu

Marlin/src/MarlinCore.cpp

@@ -1168,10 +1168,10 @@ void setup() {
   SETUP_RUN(HAL_init());
 
   // Init and disable SPI thermocouples; this is still needed
-  #if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0)
+  #if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E0))
     OUT_WRITE(TEMP_0_CS_PIN, HIGH);  // Disable
   #endif
-  #if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+  #if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E1))
     OUT_WRITE(TEMP_1_CS_PIN, HIGH);
   #endif
 

Marlin/src/core/language.h

@@ -231,6 +231,9 @@
 #define STR_HEATER_BED                      "bed"
 #define STR_HEATER_CHAMBER                  "chamber"
 #define STR_COOLER                          "cooler"
+#define STR_MOTHERBOARD                     "motherboard"
+#define STR_PROBE                           "probe"
+#define STR_REDUNDANT                       "redundant "
 #define STR_LASER_TEMP                      "laser temperature"
 
 #define STR_STOPPED_HEATER                  ", system stopped! Heater_ID: "

Marlin/src/feature/controllerfan.cpp

@@ -76,9 +76,14 @@ void ControllerFan::update() {
       )
     );
 
-    // If any of the drivers or the heated bed are enabled...
+    // If any triggers for the controller fan are true...
-    if (motor_on || TERN0(HAS_HEATED_BED, thermalManager.temp_bed.soft_pwm_amount > 0))
+    //   - At least one stepper driver is enabled
-      lastMotorOn = ms; //... set time to NOW so the fan will turn on
+    //   - The heated bed is enabled
+    //   - TEMP_SENSOR_BOARD is reporting >= CONTROLLER_FAN_MIN_BOARD_TEMP
+    if ( motor_on
+      || TERN0(HAS_HEATED_BED, thermalManager.temp_bed.soft_pwm_amount > 0)
+      || TERN0(HAS_CONTROLLER_FAN_MIN_BOARD_TEMP, thermalManager.wholeDegBoard() >= CONTROLLER_FAN_MIN_BOARD_TEMP)
+    ) lastMotorOn = ms; //... set time to NOW so the fan will turn on
 
     // Fan Settings. Set fan > 0:
     //  - If AutoMode is on and steppers have been enabled for CONTROLLERFAN_IDLE_TIME seconds.

Marlin/src/inc/Conditionals_adv.h

@@ -125,6 +125,29 @@
   #undef THERMAL_PROTECTION_COOLER
 #endif
 
+// Usurp a sensor to do redundant readings
+#if TEMP_SENSOR_REDUNDANT
+  #define REDUNDANT_TEMP_MATCH(M,N) (TEMP_SENSOR_REDUNDANT_##M == HID_##N)
+#else
+  #define REDUNDANT_TEMP_MATCH(...) 0
+#endif
+
+// Temperature sensor IDs
+#define HID_REDUNDANT -6
+#define HID_COOLER    -5
+#define HID_PROBE     -4
+#define HID_BOARD     -3
+#define HID_CHAMBER   -2
+#define HID_BED       -1
+#define HID_E0         0
+#define HID_E1         1
+#define HID_E2         2
+#define HID_E3         3
+#define HID_E4         4
+#define HID_E5         5
+#define HID_E6         6
+#define HID_E7         7
+
 #if ENABLED(MIXING_EXTRUDER) && (ENABLED(RETRACT_SYNC_MIXING) || BOTH(FILAMENT_LOAD_UNLOAD_GCODES, FILAMENT_UNLOAD_ALL_EXTRUDERS))
   #define HAS_MIXER_SYNC_CHANNEL 1
 #endif

Marlin/src/inc/Conditionals_post.h

@@ -532,84 +532,84 @@
 // Usurp a sensor to do redundant readings
 #if TEMP_SENSOR_REDUNDANT
   #ifndef TEMP_SENSOR_REDUNDANT_SOURCE
-    #define TEMP_SENSOR_REDUNDANT_SOURCE 1
+    #define TEMP_SENSOR_REDUNDANT_SOURCE E1
   #endif
   #ifndef TEMP_SENSOR_REDUNDANT_TARGET
-    #define TEMP_SENSOR_REDUNDANT_TARGET 0
+    #define TEMP_SENSOR_REDUNDANT_TARGET E0
   #endif
   #if !PIN_EXISTS(TEMP_REDUNDANT)
     #ifndef TEMP_SENSOR_REDUNDANT_MAX_DIFF
       #define TEMP_SENSOR_REDUNDANT_MAX_DIFF 10
     #endif
-    #if TEMP_SENSOR_REDUNDANT_SOURCE == -5
+    #if REDUNDANT_TEMP_MATCH(SOURCE, COOLER)
       #if !PIN_EXISTS(TEMP_COOLER)
         #error "TEMP_SENSOR_REDUNDANT_SOURCE set to COOLER requires TEMP_COOLER_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_COOLER_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == -4
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, PROBE)
       #if !PIN_EXISTS(TEMP_PROBE)
         #error "TEMP_SENSOR_REDUNDANT_SOURCE set to PROBE requires TEMP_PROBE_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_PROBE_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == -2
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, CHAMBER)
       #if !PIN_EXISTS(TEMP_CHAMBER)
         #error "TEMP_SENSOR_REDUNDANT_SOURCE set to CHAMBER requires TEMP_CHAMBER_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_CHAMBER_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == -1
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, BED)
       #if !PIN_EXISTS(TEMP_BED)
         #error "TEMP_SENSOR_REDUNDANT_SOURCE set to BED requires TEMP_BED_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_BED_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 0
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E0)
       #if !PIN_EXISTS(TEMP_0)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 0 requires TEMP_0_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E0 requires TEMP_0_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_0_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 1
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E1)
       #if !PIN_EXISTS(TEMP_1)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 1 requires TEMP_1_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E1 requires TEMP_1_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_1_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 2
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E2)
       #if !PIN_EXISTS(TEMP_2)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 2 requires TEMP_2_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E2 requires TEMP_2_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_2_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 3
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E3)
       #if !PIN_EXISTS(TEMP_3)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 3 requires TEMP_3_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E3 requires TEMP_3_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_3_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 4
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E4)
       #if !PIN_EXISTS(TEMP_4)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 4 requires TEMP_4_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E4 requires TEMP_4_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_4_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 5
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E5)
       #if !PIN_EXISTS(TEMP_5)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 5 requires TEMP_5_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E5 requires TEMP_5_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_5_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 6
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E6)
       #if !PIN_EXISTS(TEMP_6)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 6 requires TEMP_6_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E6 requires TEMP_6_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_6_PIN
       #endif
-    #elif TEMP_SENSOR_REDUNDANT_SOURCE == 7
+    #elif REDUNDANT_TEMP_MATCH(SOURCE, E7)
       #if !PIN_EXISTS(TEMP_7)
-        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to 7 requires TEMP_7_PIN."
+        #error "TEMP_SENSOR_REDUNDANT_SOURCE set to E7 requires TEMP_7_PIN."
       #else
         #define TEMP_REDUNDANT_PIN TEMP_7_PIN
       #endif
@@ -699,7 +699,7 @@
   #define TEMP_SENSOR_REDUNDANT_IS_MAX_TC 1
 
   #if TEMP_SENSOR_REDUNDANT == -5
-    #if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
+    #if !REDUNDANT_TEMP_MATCH(SOURCE, E0) && !REDUNDANT_TEMP_MATCH(SOURCE, E1)
       #error "MAX31865 Thermocouples (-5) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
     #endif
 
@@ -707,7 +707,7 @@
     #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN    0
     #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1024
   #elif TEMP_SENSOR_REDUNDANT == -3
-    #if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
+    #if !REDUNDANT_TEMP_MATCH(SOURCE, E0) && !REDUNDANT_TEMP_MATCH(SOURCE, E1)
       #error "MAX31855 Thermocouples (-3) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
     #endif
 
@@ -715,7 +715,7 @@
     #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN -270
     #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1800
   #elif TEMP_SENSOR_REDUNDANT == -2
-    #if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
+    #if !REDUNDANT_TEMP_MATCH(SOURCE, E0) && !REDUNDANT_TEMP_MATCH(SOURCE, E1)
       #error "MAX6675 Thermocouples (-2) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
     #endif
 
@@ -725,13 +725,13 @@
   #endif
 
   // mimic setting up the source TEMP_SENSOR
-  #if TEMP_SENSOR_REDUNDANT_SOURCE == 0
+  #if REDUNDANT_TEMP_MATCH(SOURCE, E0)
     #define TEMP_SENSOR_0_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
     #define TEMP_SENSOR_0_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
     #ifndef MAX31865_SENSOR_WIRES_0
       #define MAX31865_SENSOR_WIRES_0 2
     #endif
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == 1
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, E1)
     #define TEMP_SENSOR_1_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
     #define TEMP_SENSOR_1_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
     #ifndef MAX31865_SENSOR_WIRES_1
@@ -780,7 +780,7 @@
 #if HAS_MAX_TC
 
   // Translate old _SS, _CS, _SCK, _DO, _DI, _MISO, and _MOSI PIN defines.
-  #if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+  #if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E1))
 
     #if !PIN_EXISTS(TEMP_0_CS) // SS, CS
       #if PIN_EXISTS(MAX6675_SS)
@@ -849,7 +849,7 @@
 
   #endif // TEMP_SENSOR_0_IS_MAX_TC
 
-  #if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+  #if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E1))
 
     #if !PIN_EXISTS(TEMP_1_CS) // SS2, CS2
       #if PIN_EXISTS(MAX6675_SS2)
@@ -2584,6 +2584,9 @@
 #if HAS_ADC_TEST(COOLER)
   #define HAS_TEMP_ADC_COOLER 1
 #endif
+#if HAS_ADC_TEST(BOARD)
+  #define HAS_TEMP_ADC_BOARD 1
+#endif
 #if HAS_ADC_TEST(REDUNDANT)
   #define HAS_TEMP_ADC_REDUNDANT 1
 #endif
@@ -2604,6 +2607,9 @@
 #if HAS_TEMP(COOLER)
   #define HAS_TEMP_COOLER 1
 #endif
+#if HAS_TEMP(BOARD)
+  #define HAS_TEMP_BOARD 1
+#endif
 #if HAS_TEMP(REDUNDANT)
   #define HAS_TEMP_REDUNDANT 1
 #endif
@@ -2675,7 +2681,8 @@
 #if HAS_HEATED_BED || HAS_TEMP_CHAMBER
   #define BED_OR_CHAMBER 1
 #endif
-#if HAS_TEMP_HOTEND || BED_OR_CHAMBER || HAS_TEMP_PROBE || HAS_TEMP_COOLER
+
+#if HAS_TEMP_HOTEND || BED_OR_CHAMBER || HAS_TEMP_PROBE || HAS_TEMP_COOLER || HAS_TEMP_BOARD
   #define HAS_TEMP_SENSOR 1
 #endif
 
@@ -2813,9 +2820,6 @@
 #endif
 #undef _NOT_E_AUTO
 #undef _HAS_FAN
-#if PIN_EXISTS(CONTROLLER_FAN)
-  #define HAS_CONTROLLER_FAN 1
-#endif
 
 #if BED_OR_CHAMBER || HAS_FAN0
   #define BED_OR_CHAMBER_OR_FAN 1
@@ -2892,6 +2896,27 @@
   #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1)) // Fan frequency default
 #endif
 
+/**
+ * Controller Fan Settings
+ */
+#if PIN_EXISTS(CONTROLLER_FAN)
+  #define HAS_CONTROLLER_FAN 1
+  #if CONTROLLER_FAN_MIN_BOARD_TEMP
+    #define HAS_CONTROLLER_FAN_MIN_BOARD_TEMP 1
+  #endif
+#endif
+
+#if HAS_CONTROLLER_FAN
+  #if ENABLED(CONTROLLER_FAN_USE_BOARD_TEMP)
+    #define HAS_CONTROLLER_FAN_BOARD_TEMP_TRIGGER 1
+    #ifndef CONTROLLER_FAN_TRIGGER_TEMP
+      #define CONTROLLER_FAN_TRIGGER_TEMP 30
+    #endif
+  #else
+    #undef CONTROLLER_FAN_TRIGGER_TEMP
+  #endif
+#endif
+
 // Servos
 #if PIN_EXISTS(SERVO0) && NUM_SERVOS > 0
   #define HAS_SERVO_0 1

Marlin/src/inc/SanityCheck.h

@@ -583,6 +583,10 @@
   #error "TEMP_SENSOR_1_AS_REDUNDANT is now TEMP_SENSOR_REDUNDANT, with associated TEMP_SENSOR_REDUNDANT_* config."
 #elif defined(MAX_REDUNDANT_TEMP_SENSOR_DIFF)
   #error "MAX_REDUNDANT_TEMP_SENSOR_DIFF is now TEMP_SENSOR_REDUNDANT_MAX_DIFF"
+#elif MOTHERBOARD == BOARD_DUE3DOM_MINI && PIN_EXISTS(TEMP_2) && DISABLED(TEMP_SENSOR_BOARD)
+  #warning "Onboard temperature sensor for BOARD_DUE3DOM_MINI has moved from TEMP_SENSOR_2 (TEMP_2_PIN) to TEMP_SENSOR_BOARD (TEMP_BOARD_PIN)."
+#elif MOTHERBOARD == BOARD_BTT_SKR_E3_TURBO && PIN_EXISTS(TEMP_2) && DISABLED(TEMP_SENSOR_BOARD)
+  #warning "Onboard temperature sensor for BOARD_BTT_SKR_E3_TURBO has moved from TEMP_SENSOR_2 (TEMP_2_PIN) to TEMP_SENSOR_BOARD (TEMP_BOARD_PIN)."
 #endif
 
 constexpr float arm[] = AXIS_RELATIVE_MODES;
@@ -1959,6 +1963,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   #error "TEMP_SENSOR_CHAMBER 1000 requires CHAMBER_PULLUP_RESISTOR_OHMS, CHAMBER_RESISTANCE_25C_OHMS and CHAMBER_BETA in Configuration_adv.h."
 #elif TEMP_SENSOR_PROBE_IS_CUSTOM && !(defined(PROBE_PULLUP_RESISTOR_OHMS) && defined(PROBE_RESISTANCE_25C_OHMS) && defined(PROBE_BETA))
   #error "TEMP_SENSOR_PROBE 1000 requires PROBE_PULLUP_RESISTOR_OHMS, PROBE_RESISTANCE_25C_OHMS and PROBE_BETA in Configuration_adv.h."
+#elif TEMP_SENSOR_BOARD_IS_CUSTOM && !(defined(BOARD_PULLUP_RESISTOR_OHMS) && defined(BOARD_RESISTANCE_25C_OHMS) && defined(BOARD_BETA))
+  #error "TEMP_SENSOR_BOARD 1000 requires BOARD_PULLUP_RESISTOR_OHMS, BOARD_RESISTANCE_25C_OHMS and BOARD_BETA in Configuration_adv.h."
 #elif TEMP_SENSOR_REDUNDANT_IS_CUSTOM && !(defined(REDUNDANT_PULLUP_RESISTOR_OHMS) && defined(REDUNDANT_RESISTANCE_25C_OHMS) && defined(REDUNDANT_BETA))
   #error "TEMP_SENSOR_REDUNDANT 1000 requires REDUNDANT_PULLUP_RESISTOR_OHMS, REDUNDANT_RESISTANCE_25C_OHMS and REDUNDANT_BETA in Configuration_adv.h."
 #endif
@@ -1966,14 +1972,14 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * Required MAX31865 settings
  */
-#if TEMP_SENSOR_0_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && TEMP_SENSOR_REDUNDANT_SOURCE == 0)
+#if TEMP_SENSOR_0_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && REDUNDANT_TEMP_MATCH(SOURCE, E0))
   #if !defined(MAX31865_SENSOR_WIRES_0) || !WITHIN(MAX31865_SENSOR_WIRES_0, 2, 4)
     #error "MAX31865_SENSOR_WIRES_0 must be defined as an integer between 2 and 4."
   #elif !defined(MAX31865_SENSOR_OHMS_0) || !defined(MAX31865_CALIBRATION_OHMS_0)
     #error "MAX31865_SENSOR_OHMS_0 and MAX31865_CALIBRATION_OHMS_0 must be set if TEMP_SENSOR_0/TEMP_SENSOR_REDUNDANT is MAX31865."
   #endif
 #endif
-#if TEMP_SENSOR_1_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+#if TEMP_SENSOR_1_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && REDUNDANT_TEMP_MATCH(SOURCE, E1))
   #if !defined(MAX31865_SENSOR_WIRES_1) || !WITHIN(MAX31865_SENSOR_WIRES_1, 2, 4)
     #error "MAX31865_SENSOR_WIRES_1 must be defined as an integer between 2 and 4."
   #elif !defined(MAX31865_SENSOR_OHMS_1) || !defined(MAX31865_CALIBRATION_OHMS_1)
@@ -1989,62 +1995,58 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
     #error "TEMP_SENSOR_REDUNDANT requires TEMP_SENSOR_REDUNDANT_SOURCE."
   #elif !defined(TEMP_SENSOR_REDUNDANT_TARGET)
     #error "TEMP_SENSOR_REDUNDANT requires TEMP_SENSOR_REDUNDANT_TARGET."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == TEMP_SENSOR_REDUNDANT_TARGET
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, TEMP_SENSOR_REDUNDANT_TARGET)
     #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be the same as TEMP_SENSOR_REDUNDANT_TARGET."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE < -5 || TEMP_SENSOR_REDUNDANT_SOURCE > 7
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE must be between -5 and 7."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET < -5 || TEMP_SENSOR_REDUNDANT_TARGET > 7
-    #error "TEMP_SENSOR_REDUNDANT_TARGET must be between -5 and 7."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == -3
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be -3 (not used)."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == -3
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be -3 (not used)."
   #elif HAS_MULTI_HOTEND && TEMP_SENSOR_REDUNDANT_SOURCE < HOTENDS
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE must be after the last TEMP_SENSOR used with a hotend; you can't use a sensor in the middle of two hotends."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE must be after the last used hotend TEMP_SENSOR."
   #endif
 
-  #if TEMP_SENSOR_REDUNDANT_SOURCE == 0 && HAS_HOTEND
+  #if REDUNDANT_TEMP_MATCH(SOURCE, E0) && HAS_HOTEND
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can not be 0 if a hotend is used. E0 always uses TEMP_SENSOR_0."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be 0 if a hotend is used. E0 always uses TEMP_SENSOR_0."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == -5 && HAS_TEMP_COOLER
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, COOLER) && HAS_TEMP_COOLER
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be Cooler (-5): TEMP_SENSOR_COOLER has already defined the sensor."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be COOLER. TEMP_SENSOR_COOLER is in use."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == -4 && HAS_TEMP_PROBE
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, PROBE) && HAS_TEMP_PROBE
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be Probe (-4): TEMP_SENSOR_PROBE has already defined the sensor."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be PROBE. TEMP_SENSOR_PROBE is in use."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == -2 && HAS_TEMP_CHAMBER
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, BOARD) && HAS_TEMP_BOARD
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be Chamber (-2): TEMP_SENSOR_CHAMBER has already defined the sensor."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be BOARD. TEMP_SENSOR_BOARD is in use."
-  #elif TEMP_SENSOR_REDUNDANT_SOURCE == -1 && HAS_TEMP_BED
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, CHAMBER) && HAS_TEMP_CHAMBER
-    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be Bed (-1): TEMP_SENSOR_BED has already defined the sensor."
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be CHAMBER. TEMP_SENSOR_CHAMBER is in use."
+  #elif REDUNDANT_TEMP_MATCH(SOURCE, BED) && HAS_TEMP_BED
+    #error "TEMP_SENSOR_REDUNDANT_SOURCE can't be BED. TEMP_SENSOR_BED is in use."
   #endif
 
-  #if TEMP_SENSOR_REDUNDANT_TARGET == 0 && !PIN_EXISTS(TEMP_0)
+  #if REDUNDANT_TEMP_MATCH(TARGET, E0) && !PIN_EXISTS(TEMP_0)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E0 (0): requires TEMP_0_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E0 without TEMP_0_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 1 && !PIN_EXISTS(TEMP_1)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E1) && !PIN_EXISTS(TEMP_1)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E1 (1): requires TEMP_1_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E1 without TEMP_1_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 2 && !PIN_EXISTS(TEMP_2)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E2) && !PIN_EXISTS(TEMP_2)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E2 (2): requires TEMP_2_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E2 without TEMP_2_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 3 && !PIN_EXISTS(TEMP_3)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E3) && !PIN_EXISTS(TEMP_3)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E3 (3): requires TEMP_3_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E3 without TEMP_3_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 4 && !PIN_EXISTS(TEMP_4)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E4) && !PIN_EXISTS(TEMP_4)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E4 (4): requires TEMP_4_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E4 without TEMP_4_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 5 && !PIN_EXISTS(TEMP_5)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E5) && !PIN_EXISTS(TEMP_5)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E5 (5): requires TEMP_5_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E5 without TEMP_5_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 6 && !PIN_EXISTS(TEMP_6)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E6) && !PIN_EXISTS(TEMP_6)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E6 (6): requires TEMP_6_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E6 without TEMP_6_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == 7 && !PIN_EXISTS(TEMP_7)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, E7) && !PIN_EXISTS(TEMP_7)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E7 (7): requires TEMP_7_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be E7 without TEMP_7_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == -1 && !PIN_EXISTS(TEMP_BED)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, BED) && !PIN_EXISTS(TEMP_BED)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be Bed (-1): requires TEMP_BED_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be BED without TEMP_BED_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == -2 && !PIN_EXISTS(TEMP_CHAMBER)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, CHAMBER) && !PIN_EXISTS(TEMP_CHAMBER)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be Chamber (-2): requires TEMP_CHAMBER_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be CHAMBER without TEMP_CHAMBER_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == -4 && !PIN_EXISTS(TEMP_PROBE)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, BOARD) && !PIN_EXISTS(TEMP_BOARD)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be Probe (-4): requires TEMP_PROBE_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be BOARD without TEMP_BOARD_PIN defined."
-  #elif TEMP_SENSOR_REDUNDANT_TARGET == -5 && !PIN_EXISTS(TEMP_COOLER)
+  #elif REDUNDANT_TEMP_MATCH(TARGET, PROBE) && !PIN_EXISTS(TEMP_PROBE)
-    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be Cooler (-5): requires TEMP_COOLER_PIN"
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be PROBE without TEMP_PROBE_PIN defined."
+  #elif REDUNDANT_TEMP_MATCH(TARGET, COOLER) && !PIN_EXISTS(TEMP_COOLER)
+    #error "TEMP_SENSOR_REDUNDANT_TARGET can't be COOLER without TEMP_COOLER_PIN defined."
   #endif
 
-  #if TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0 && !PIN_EXISTS(TEMP_0_CS)
+  #if TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E0) && !PIN_EXISTS(TEMP_0_CS)
-    #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 0 requires TEMP_0_CS_PIN."
+    #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE E0 requires TEMP_0_CS_PIN."
-  #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1 && !PIN_EXISTS(TEMP_1_CS)
+  #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E1) && !PIN_EXISTS(TEMP_1_CS)
-    #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 1 requires TEMP_1_CS_PIN."
+    #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE E1 requires TEMP_1_CS_PIN."
   #endif
 #endif
 
@@ -2209,6 +2211,28 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   #endif
 #endif
 
+#if TEMP_SENSOR_PROBE
+  #if !PIN_EXISTS(TEMP_PROBE)
+    #error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN."
+  #elif !HAS_TEMP_ADC_PROBE
+    #error "TEMP_PROBE_PIN must be an ADC pin."
+  #elif DISABLED(FIX_MOUNTED_PROBE)
+    #error "TEMP_SENSOR_PROBE shouldn't be set without FIX_MOUNTED_PROBE."
+  #endif
+#endif
+
+#if TEMP_SENSOR_BOARD
+  #if !PIN_EXISTS(TEMP_BOARD)
+    #error "TEMP_SENSOR_BOARD requires TEMP_BOARD_PIN."
+  #elif !HAS_TEMP_ADC_BOARD
+    #error "TEMP_BOARD_PIN must be an ADC pin."
+  #elif ENABLED(THERMAL_PROTECTION_BOARD) && (!defined(BOARD_MINTEMP) || !defined(BOARD_MAXTEMP))
+    #error "THERMAL_PROTECTION_BOARD requires BOARD_MINTEMP and BOARD_MAXTEMP."
+  #endif
+#elif CONTROLLER_FAN_MIN_BOARD_TEMP
+  #error "CONTROLLER_FAN_MIN_BOARD_TEMP requires TEMP_SENSOR_BOARD."
+#endif
+
 #if ENABLED(LASER_COOLANT_FLOW_METER) && !(PIN_EXISTS(FLOWMETER) && ENABLED(LASER_FEATURE))
   #error "LASER_COOLANT_FLOW_METER requires FLOWMETER_PIN and LASER_FEATURE."
 #endif

Marlin/src/module/temperature.cpp

@@ -58,8 +58,8 @@
 #endif
 
 // MAX TC related macros
-#define TEMP_SENSOR_IS_MAX(n, M) (ENABLED(TEMP_SENSOR_##n##_IS_MAX##M) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX##M) && TEMP_SENSOR_REDUNDANT_SOURCE == (n)))
+#define TEMP_SENSOR_IS_MAX(n, M) (ENABLED(TEMP_SENSOR_##n##_IS_MAX##M) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX##M) && REDUNDANT_TEMP_MATCH(SOURCE, E##n)))
-#define TEMP_SENSOR_IS_ANY_MAX_TC(n) (ENABLED(TEMP_SENSOR_##n##_IS_MAX_TC) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX_TC) && TEMP_SENSOR_REDUNDANT_SOURCE == n))
+#define TEMP_SENSOR_IS_ANY_MAX_TC(n) (ENABLED(TEMP_SENSOR_##n##_IS_MAX_TC) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX_TC) && REDUNDANT_TEMP_MATCH(SOURCE, E##n)))
 
 // LIB_MAX6675 can be added to the build_flags in platformio.ini to use a user-defined library
 // If LIB_MAX6675 is not on the build_flags then raw SPI reads will be used.
@@ -262,7 +262,7 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
 #endif
 
 #if HAS_TEMP_REDUNDANT
-  redundant_temp_info_t Temperature::temp_redundant;
+  redundant_info_t Temperature::temp_redundant;
 #endif
 
 #if ENABLED(AUTO_POWER_E_FANS)
@@ -436,6 +436,14 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
   probe_info_t Temperature::temp_probe; // = { 0 }
 #endif
 
+#if HAS_TEMP_BOARD
+  board_info_t Temperature::temp_board; // = { 0 }
+  #if ENABLED(THERMAL_PROTECTION_BOARD)
+    int16_t Temperature::mintemp_raw_BOARD = TEMP_SENSOR_BOARD_RAW_LO_TEMP,
+            Temperature::maxtemp_raw_BOARD = TEMP_SENSOR_COOLER_RAW_HI_TEMP;
+  #endif
+#endif
+
 #if ENABLED(PREVENT_COLD_EXTRUSION)
   bool Temperature::allow_cold_extrude = false;
   celsius_t Temperature::extrude_min_temp = EXTRUDE_MINTEMP;
@@ -937,14 +945,26 @@ void Temperature::_temp_error(const heater_id_t heater_id, PGM_P const serial_ms
     SERIAL_ERROR_START();
     SERIAL_ECHOPGM_P(serial_msg);
     SERIAL_ECHOPGM(STR_STOPPED_HEATER);
-    if (heater_id >= 0)
+
-      SERIAL_ECHO(heater_id);
+    heater_id_t real_heater_id = heater_id;
-    else if (TERN0(HAS_HEATED_CHAMBER, heater_id == H_CHAMBER))
+
-      SERIAL_ECHOPGM(STR_HEATER_CHAMBER);
+    #if HAS_TEMP_REDUNDANT
-    else if (TERN0(HAS_COOLER, heater_id == H_COOLER))
+      if (heater_id == H_REDUNDANT) {
-      SERIAL_ECHOPGM(STR_COOLER);
+        SERIAL_ECHOPGM(STR_REDUNDANT); // print redundant and cascade to print target, too.
-    else
+        real_heater_id = (heater_id_t)TEMP_SENSOR_REDUNDANT_TARGET;
-      SERIAL_ECHOPGM(STR_HEATER_BED);
+      }
+    #endif
+
+    switch (real_heater_id) {
+      OPTCODE(HAS_TEMP_COOLER,  case H_COOLER:  SERIAL_ECHOPGM(STR_COOLER);         break)
+      OPTCODE(HAS_TEMP_PROBE,   case H_PROBE:   SERIAL_ECHOPGM(STR_PROBE);          break)
+      OPTCODE(HAS_TEMP_BOARD,   case H_BOARD:   SERIAL_ECHOPGM(STR_MOTHERBOARD);    break)
+      OPTCODE(HAS_TEMP_CHAMBER, case H_CHAMBER: SERIAL_ECHOPGM(STR_HEATER_CHAMBER); break)
+      OPTCODE(HAS_TEMP_BED,     case H_BED:     SERIAL_ECHOPGM(STR_HEATER_BED);     break)
+      default:
+        if (real_heater_id >= 0)
+          SERIAL_ECHOLNPAIR("E", real_heater_id);
+    }
     SERIAL_EOL();
   }
 
@@ -1663,6 +1683,9 @@ void Temperature::manage_heater() {
       #if TEMP_SENSOR_PROBE_IS_CUSTOM
         { true, 0, 0, PROBE_PULLUP_RESISTOR_OHMS, PROBE_RESISTANCE_25C_OHMS, 0, 0, PROBE_BETA, 0 },
       #endif
+      #if TEMP_SENSOR_BOARD_IS_CUSTOM
+        { true, 0, 0, BOARD_PULLUP_RESISTOR_OHMS, BOARD_RESISTANCE_25C_OHMS, 0, 0, BOARD_BETA, 0 },
+      #endif
       #if TEMP_SENSOR_REDUNDANT_IS_CUSTOM
         { true, 0, 0, REDUNDANT_PULLUP_RESISTOR_OHMS, REDUNDANT_RESISTANCE_25C_OHMS, 0, 0, REDUNDANT_BETA, 0 },
       #endif
@@ -1698,6 +1721,7 @@ void Temperature::manage_heater() {
       TERN_(TEMP_SENSOR_CHAMBER_IS_CUSTOM, t_index == CTI_CHAMBER ? PSTR("CHAMBER") :)
       TERN_(TEMP_SENSOR_COOLER_IS_CUSTOM, t_index == CTI_COOLER ? PSTR("COOLER") :)
       TERN_(TEMP_SENSOR_PROBE_IS_CUSTOM, t_index == CTI_PROBE ? PSTR("PROBE") :)
+      TERN_(TEMP_SENSOR_BOARD_IS_CUSTOM, t_index == CTI_BOARD ? PSTR("BOARD") :)
       TERN_(TEMP_SENSOR_REDUNDANT_IS_CUSTOM, t_index == CTI_REDUNDANT ? PSTR("REDUNDANT") :)
       nullptr
     );
@@ -1933,14 +1957,32 @@ void Temperature::manage_heater() {
   }
 #endif // HAS_TEMP_PROBE
 
+#if HAS_TEMP_BOARD
+  // For motherboard temperature measurement.
+  celsius_float_t Temperature::analog_to_celsius_board(const int16_t raw) {
+    #if TEMP_SENSOR_BOARD_IS_CUSTOM
+      return user_thermistor_to_deg_c(CTI_BOARD, raw);
+    #elif TEMP_SENSOR_BOARD_IS_THERMISTOR
+      SCAN_THERMISTOR_TABLE(TEMPTABLE_BOARD, TEMPTABLE_BOARD_LEN);
+    #elif TEMP_SENSOR_BOARD_IS_AD595
+      return TEMP_AD595(raw);
+    #elif TEMP_SENSOR_BOARD_IS_AD8495
+      return TEMP_AD8495(raw);
+    #else
+      UNUSED(raw);
+      return 0;
+    #endif
+  }
+#endif // HAS_TEMP_BOARD
+
 #if HAS_TEMP_REDUNDANT
   // For redundant temperature measurement.
   celsius_float_t Temperature::analog_to_celsius_redundant(const int16_t raw) {
     #if TEMP_SENSOR_REDUNDANT_IS_CUSTOM
       return user_thermistor_to_deg_c(CTI_REDUNDANT, raw);
-    #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0
+    #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E0)
       return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_0.temperature((uint16_t)raw), raw * 0.25);
-    #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1
+    #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && REDUNDANT_TEMP_MATCH(SOURCE, E1)
       return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_1.temperature((uint16_t)raw), raw * 0.25);
     #elif TEMP_SENSOR_REDUNDANT_IS_THERMISTOR
       SCAN_THERMISTOR_TABLE(TEMPTABLE_REDUNDANT, TEMPTABLE_REDUNDANT_LEN);
@@ -1983,6 +2025,7 @@ void Temperature::updateTemperaturesFromRawValues() {
   TERN_(HAS_TEMP_CHAMBER,   temp_chamber.celsius   = analog_to_celsius_chamber(temp_chamber.raw));
   TERN_(HAS_TEMP_COOLER,    temp_cooler.celsius    = analog_to_celsius_cooler(temp_cooler.raw));
   TERN_(HAS_TEMP_PROBE,     temp_probe.celsius     = analog_to_celsius_probe(temp_probe.raw));
+  TERN_(HAS_TEMP_BOARD,     temp_board.celsius     = analog_to_celsius_board(temp_board.raw));
   TERN_(HAS_TEMP_REDUNDANT, temp_redundant.celsius = analog_to_celsius_redundant(temp_redundant.raw));
 
   TERN_(FILAMENT_WIDTH_SENSOR, filwidth.update_measured_mm());
@@ -2030,23 +2073,28 @@ void Temperature::updateTemperaturesFromRawValues() {
 
   #endif // HAS_HOTEND
 
+  #define TP_CMP(S,A,B) (TEMPDIR(S) < 0 ? ((A)<(B)) : ((A)>(B)))
   #if ENABLED(THERMAL_PROTECTION_BED)
-    #define BEDCMP(A,B) (TEMPDIR(BED) < 0 ? ((A)<(B)) : ((A)>(B)))
+    if (TP_CMP(BED, temp_bed.raw, maxtemp_raw_BED)) max_temp_error(H_BED);
-    if (BEDCMP(temp_bed.raw, maxtemp_raw_BED)) max_temp_error(H_BED);
+    if (temp_bed.target > 0 && TP_CMP(BED, mintemp_raw_BED, temp_bed.raw)) min_temp_error(H_BED);
-    if (temp_bed.target > 0 && BEDCMP(mintemp_raw_BED, temp_bed.raw)) min_temp_error(H_BED);
   #endif
 
   #if BOTH(HAS_HEATED_CHAMBER, THERMAL_PROTECTION_CHAMBER)
-    #define CHAMBERCMP(A,B) (TEMPDIR(CHAMBER) < 0 ? ((A)<(B)) : ((A)>(B)))
+    if (TP_CMP(CHAMBER, temp_chamber.raw, maxtemp_raw_CHAMBER)) max_temp_error(H_CHAMBER);
-    if (CHAMBERCMP(temp_chamber.raw, maxtemp_raw_CHAMBER)) max_temp_error(H_CHAMBER);
+    if (temp_chamber.target > 0 && TP_CMP(CHAMBER, mintemp_raw_CHAMBER, temp_chamber.raw)) min_temp_error(H_CHAMBER);
-    if (temp_chamber.target > 0 && CHAMBERCMP(mintemp_raw_CHAMBER, temp_chamber.raw)) min_temp_error(H_CHAMBER);
   #endif
 
   #if BOTH(HAS_COOLER, THERMAL_PROTECTION_COOLER)
-    #define COOLERCMP(A,B) (TEMPDIR(COOLER) < 0 ? ((A)<(B)) : ((A)>(B)))
+    if (cutter.unitPower > 0 && TP_CMP(COOLER, temp_cooler.raw, maxtemp_raw_COOLER)) max_temp_error(H_COOLER);
-    if (cutter.unitPower > 0 && COOLERCMP(temp_cooler.raw, maxtemp_raw_COOLER)) max_temp_error(H_COOLER);
+    if (TP_CMP(COOLER, mintemp_raw_COOLER, temp_cooler.raw)) min_temp_error(H_COOLER);
-    if (COOLERCMP(mintemp_raw_COOLER, temp_cooler.raw)) min_temp_error(H_COOLER);
   #endif
+
+  #if BOTH(HAS_TEMP_BOARD, THERMAL_PROTECTION_BOARD)
+    if (TP_CMP(BOARD, temp_board.raw, maxtemp_raw_BOARD)) max_temp_error(H_BOARD);
+    if (TP_CMP(BOARD, mintemp_raw_BOARD, temp_board.raw)) min_temp_error(H_BOARD);
+  #endif
+  #undef TP_CMP
+
 } // Temperature::updateTemperaturesFromRawValues
 
 /**
@@ -2275,6 +2323,9 @@ void Temperature::init() {
   #if HAS_TEMP_ADC_PROBE
     HAL_ANALOG_SELECT(TEMP_PROBE_PIN);
   #endif
+  #if HAS_TEMP_ADC_BOARD
+    HAL_ANALOG_SELECT(TEMP_BOARD_PIN);
+  #endif
   #if HAS_TEMP_ADC_REDUNDANT
     HAL_ANALOG_SELECT(TEMP_REDUNDANT_PIN);
   #endif
@@ -2388,6 +2439,7 @@ void Temperature::init() {
     #endif
   #endif // HAS_HOTEND
 
+  // TODO: combine these into the macros above
   #if HAS_HEATED_BED
     while (analog_to_celsius_bed(mintemp_raw_BED) < BED_MINTEMP) mintemp_raw_BED += TEMPDIR(BED) * (OVERSAMPLENR);
     while (analog_to_celsius_bed(maxtemp_raw_BED) > BED_MAXTEMP) maxtemp_raw_BED -= TEMPDIR(BED) * (OVERSAMPLENR);
@@ -2403,15 +2455,22 @@ void Temperature::init() {
     while (analog_to_celsius_cooler(maxtemp_raw_COOLER) < COOLER_MAXTEMP) maxtemp_raw_COOLER -= TEMPDIR(COOLER) * (OVERSAMPLENR);
   #endif
 
+  #if HAS_TEMP_BOARD
+    while (analog_to_celsius_board(mintemp_raw_BOARD) > BOARD_MINTEMP) mintemp_raw_BOARD += TEMPDIR(BOARD) * (OVERSAMPLENR);
+    while (analog_to_celsius_board(maxtemp_raw_BOARD) < BOARD_MAXTEMP) maxtemp_raw_BOARD -= TEMPDIR(BOARD) * (OVERSAMPLENR);
+  #endif
+
   #if HAS_TEMP_REDUNDANT
     temp_redundant.target = &(
-      #if TEMP_SENSOR_REDUNDANT_TARGET == -5 && HAS_TEMP_COOLER
+      #if REDUNDANT_TEMP_MATCH(TARGET, COOLER) && HAS_TEMP_COOLER
         temp_cooler
-      #elif TEMP_SENSOR_REDUNDANT_TARGET == -4 && HAS_TEMP_PROBE
+      #elif REDUNDANT_TEMP_MATCH(TARGET, PROBE) && HAS_TEMP_PROBE
         temp_probe
-      #elif TEMP_SENSOR_REDUNDANT_TARGET == -2 && HAS_TEMP_CHAMBER
+      #elif REDUNDANT_TEMP_MATCH(TARGET, BOARD) && HAS_TEMP_BOARD
+        temp_board
+      #elif REDUNDANT_TEMP_MATCH(TARGET, CHAMBER) && HAS_TEMP_CHAMBER
         temp_chamber
-      #elif TEMP_SENSOR_REDUNDANT_TARGET == -1 && HAS_TEMP_BED
+      #elif REDUNDANT_TEMP_MATCH(TARGET, BED) && HAS_TEMP_BED
         temp_bed
       #else
         temp_hotend[TEMP_SENSOR_REDUNDANT_TARGET]
@@ -2787,6 +2846,7 @@ void Temperature::disable_all_heaters() {
  */
 void Temperature::update_raw_temperatures() {
 
+  // TODO: can this be collapsed into a HOTEND_LOOP()?
   #if HAS_TEMP_ADC_0 && !TEMP_SENSOR_0_IS_MAX_TC
     temp_hotend[0].update();
   #endif
@@ -2808,6 +2868,7 @@ void Temperature::update_raw_temperatures() {
   TERN_(HAS_TEMP_ADC_BED,     temp_bed.update());
   TERN_(HAS_TEMP_ADC_CHAMBER, temp_chamber.update());
   TERN_(HAS_TEMP_ADC_PROBE,   temp_probe.update());
+  TERN_(HAS_TEMP_ADC_BOARD,   temp_board.update());
   TERN_(HAS_TEMP_ADC_COOLER,  temp_cooler.update());
 
   TERN_(HAS_JOY_ADC_X, joystick.x.update());
@@ -2838,6 +2899,7 @@ void Temperature::readings_ready() {
   TERN_(HAS_TEMP_CHAMBER,   temp_chamber.reset());
   TERN_(HAS_TEMP_PROBE,     temp_probe.reset());
   TERN_(HAS_TEMP_COOLER,    temp_cooler.reset());
+  TERN_(HAS_TEMP_BOARD,     temp_board.reset());
   TERN_(HAS_TEMP_REDUNDANT, temp_redundant.reset());
 
   TERN_(HAS_JOY_ADC_X, joystick.x.reset());
@@ -3264,6 +3326,11 @@ void Temperature::isr() {
       case MeasureTemp_PROBE: ACCUMULATE_ADC(temp_probe); break;
     #endif
 
+    #if HAS_TEMP_ADC_BOARD
+      case PrepareTemp_BOARD: HAL_START_ADC(TEMP_BOARD_PIN); break;
+      case MeasureTemp_BOARD: ACCUMULATE_ADC(temp_board); break;
+    #endif
+
     #if HAS_TEMP_ADC_REDUNDANT
       case PrepareTemp_REDUNDANT: HAL_START_ADC(TEMP_REDUNDANT_PIN); break;
       case MeasureTemp_REDUNDANT: ACCUMULATE_ADC(temp_redundant); break;
@@ -3430,6 +3497,9 @@ void Temperature::isr() {
       #if HAS_TEMP_COOLER
         case H_COOLER: k = 'L'; break;
       #endif
+      #if HAS_TEMP_BOARD
+        case H_BOARD: k = 'M'; break;
+      #endif
       #if HAS_TEMP_REDUNDANT
         case H_REDUNDANT: k = 'R'; break;
       #endif
@@ -3459,7 +3529,7 @@ void Temperature::isr() {
     OPTARG(HAS_TEMP_REDUNDANT, const bool include_r/*=false*/)
   ) {
     #if HAS_TEMP_HOTEND
-      print_heater_state(H_NONE, degHotend(target_extruder), degTargetHotend(target_extruder) OPTARG(SHOW_TEMP_ADC_VALUES, rawHotendTemp(target_extruder)));
+      print_heater_state(H_E0, degHotend(target_extruder), degTargetHotend(target_extruder) OPTARG(SHOW_TEMP_ADC_VALUES, rawHotendTemp(target_extruder)));
     #endif
     #if HAS_HEATED_BED
       print_heater_state(H_BED, degBed(), degTargetBed() OPTARG(SHOW_TEMP_ADC_VALUES, rawBedTemp()));
@@ -3471,7 +3541,10 @@ void Temperature::isr() {
       print_heater_state(H_COOLER, degCooler(), TERN0(HAS_COOLER, degTargetCooler()) OPTARG(SHOW_TEMP_ADC_VALUES, rawCoolerTemp()));
     #endif
     #if HAS_TEMP_PROBE
-      print_heater_state(H_PROBE, degProbe(), 0 OPTARG(SHOW_TEMP_ADC_VALUES, rawProbeTemp()) );
+      print_heater_state(H_PROBE, degProbe(), 0 OPTARG(SHOW_TEMP_ADC_VALUES, rawProbeTemp()));
+    #endif
+    #if HAS_TEMP_BOARD
+      print_heater_state(H_BOARD, degBoard(), 0 OPTARG(SHOW_TEMP_ADC_VALUES, rawBoardTemp()));
     #endif
     #if HAS_TEMP_REDUNDANT
       if (include_r) print_heater_state(H_REDUNDANT, degRedundant(), degRedundantTarget() OPTARG(SHOW_TEMP_ADC_VALUES, rawRedundantTemp()));

Marlin/src/module/temperature.h

@@ -46,9 +46,13 @@
 
 // Element identifiers. Positive values are hotends. Negative values are other heaters or coolers.
 typedef enum : int8_t {
-  H_NONE = -6,
+  H_REDUNDANT = HID_REDUNDANT,
-  H_COOLER, H_PROBE, H_REDUNDANT, H_CHAMBER, H_BED,
+  H_COOLER = HID_COOLER,
-  H_E0, H_E1, H_E2, H_E3, H_E4, H_E5, H_E6, H_E7
+  H_PROBE = HID_PROBE,
+  H_BOARD = HID_BOARD,
+  H_CHAMBER = HID_CHAMBER,
+  H_BED = HID_BED,
+  H_E0 = HID_E0, H_E1, H_E2, H_E3, H_E4, H_E5, H_E6, H_E7
 } heater_id_t;
 
 // PID storage
@@ -105,6 +109,9 @@ enum ADCSensorState : char {
   #if HAS_TEMP_ADC_PROBE
     PrepareTemp_PROBE, MeasureTemp_PROBE,
   #endif
+  #if HAS_TEMP_ADC_BOARD
+    PrepareTemp_BOARD, MeasureTemp_BOARD,
+  #endif
   #if HAS_TEMP_ADC_REDUNDANT
     PrepareTemp_REDUNDANT, MeasureTemp_REDUNDANT,
   #endif
@@ -192,7 +199,7 @@ typedef struct TempInfo {
   // A redundant temperature sensor
   typedef struct RedundantTempInfo : public TempInfo {
     temp_info_t* target;
-  } redundant_temp_info_t;
+  } redundant_info_t;
 #endif
 
 // A PWM heater with temperature sensor
@@ -231,6 +238,9 @@ struct PIDHeaterInfo : public HeaterInfo {
 #elif HAS_TEMP_CHAMBER
   typedef temp_info_t chamber_info_t;
 #endif
+#if HAS_TEMP_BOARD
+  typedef temp_info_t board_info_t;
+#endif
 #if EITHER(HAS_COOLER, HAS_TEMP_COOLER)
   typedef heater_info_t cooler_info_t;
 #endif
@@ -312,6 +322,9 @@ typedef struct { int16_t raw_min, raw_max; celsius_t mintemp, maxtemp; } temp_ra
     #if TEMP_SENSOR_COOLER_IS_CUSTOM
       CTI_COOLER,
     #endif
+    #if TEMP_SENSOR_BOARD_IS_CUSTOM
+      CTI_BOARD,
+    #endif
     #if TEMP_SENSOR_REDUNDANT_IS_CUSTOM
       CTI_REDUNDANT,
     #endif
@@ -352,8 +365,11 @@ class Temperature {
     #if HAS_TEMP_COOLER
       static cooler_info_t temp_cooler;
     #endif
+    #if HAS_TEMP_BOARD
+      static board_info_t temp_board;
+    #endif
     #if HAS_TEMP_REDUNDANT
-      static redundant_temp_info_t temp_redundant;
+      static redundant_info_t temp_redundant;
     #endif
 
     #if ENABLED(AUTO_POWER_E_FANS)
@@ -478,6 +494,10 @@ class Temperature {
       static int16_t mintemp_raw_COOLER, maxtemp_raw_COOLER;
     #endif
 
+    #if HAS_TEMP_BOARD && ENABLED(THERMAL_PROTECTION_BOARD)
+      static int16_t mintemp_raw_BOARD, maxtemp_raw_BOARD;
+    #endif
+
     #if MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED > 1
       static uint8_t consecutive_low_temperature_error[HOTENDS];
     #endif
@@ -551,6 +571,9 @@ class Temperature {
     #if HAS_TEMP_COOLER
       static celsius_float_t analog_to_celsius_cooler(const int16_t raw);
     #endif
+    #if HAS_TEMP_BOARD
+      static celsius_float_t analog_to_celsius_board(const int16_t raw);
+    #endif
     #if HAS_TEMP_REDUNDANT
       static celsius_float_t analog_to_celsius_redundant(const int16_t raw);
     #endif
@@ -787,6 +810,14 @@ class Temperature {
       #endif
     #endif
 
+    #if HAS_TEMP_BOARD
+      #if ENABLED(SHOW_TEMP_ADC_VALUES)
+        static inline int16_t rawBoardTemp()    { return temp_board.raw; }
+      #endif
+      static inline celsius_float_t degBoard()  { return temp_board.celsius; }
+      static inline celsius_t wholeDegBoard()   { return static_cast<celsius_t>(degBoard() + 0.5f); }
+    #endif
+
     #if HAS_TEMP_REDUNDANT
       #if ENABLED(SHOW_TEMP_ADC_VALUES)
         static inline int16_t rawRedundantTemp()         { return temp_redundant.raw; }

Marlin/src/module/thermistor/thermistors.h

@@ -51,6 +51,7 @@
                             || TEMP_SENSOR_IS(n, CHAMBER) \
                             || TEMP_SENSOR_IS(n, COOLER) \
                             || TEMP_SENSOR_IS(n, PROBE) \
+                            || TEMP_SENSOR_IS(n, BOARD) \
                             || TEMP_SENSOR_IS(n, REDUNDANT) )
 
 typedef struct { int16_t value; celsius_t celsius; } temp_entry_t;
@@ -305,6 +306,13 @@ typedef struct { int16_t value; celsius_t celsius; } temp_entry_t;
   #define TEMPTABLE_PROBE_LEN 0
 #endif
 
+#if TEMP_SENSOR_BOARD > 0
+  #define TEMPTABLE_BOARD TT_NAME(TEMP_SENSOR_BOARD)
+  #define TEMPTABLE_BOARD_LEN COUNT(TEMPTABLE_BOARD)
+#else
+  #define TEMPTABLE_BOARD_LEN 0
+#endif
+
 #if TEMP_SENSOR_REDUNDANT > 0
   #define TEMPTABLE_REDUNDANT TT_NAME(TEMP_SENSOR_REDUNDANT)
   #define TEMPTABLE_REDUNDANT_LEN COUNT(TEMPTABLE_REDUNDANT)
@@ -319,6 +327,7 @@ static_assert(255 > TEMPTABLE_0_LEN || 255 > TEMPTABLE_1_LEN || 255 > TEMPTABLE_
            || 255 > TEMPTABLE_CHAMBER_LEN
            || 255 > TEMPTABLE_COOLER_LEN
            || 255 > TEMPTABLE_PROBE_LEN
+           || 255 > TEMPTABLE_BOARD_LEN
            || 255 > TEMPTABLE_REDUNDANT_LEN
   , "Temperature conversion tables over 255 entries need special consideration."
 );
@@ -513,6 +522,15 @@ static_assert(255 > TEMPTABLE_0_LEN || 255 > TEMPTABLE_1_LEN || 255 > TEMPTABLE_
     #define TEMP_SENSOR_PROBE_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE
   #endif
 #endif
+#ifndef TEMP_SENSOR_BOARD_RAW_HI_TEMP
+  #if TT_REVRAW(BOARD)
+    #define TEMP_SENSOR_BOARD_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE
+    #define TEMP_SENSOR_BOARD_RAW_LO_TEMP 0
+  #else
+    #define TEMP_SENSOR_BOARD_RAW_HI_TEMP 0
+    #define TEMP_SENSOR_BOARD_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE
+  #endif
+#endif
 #ifndef TEMP_SENSOR_REDUNDANT_RAW_HI_TEMP
   #if TT_REVRAW(REDUNDANT)
     #define TEMP_SENSOR_REDUNDANT_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE

Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h

@@ -65,7 +65,7 @@
   #define TEMP_BED_PIN                  P0_23_A0  // A0 (T0) - (67) - TEMP_BED_PIN
 #endif
 
-#if HOTENDS == 1 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
+#if HOTENDS == 1 && !REDUNDANT_TEMP_MATCH(SOURCE, E1)
   #if TEMP_SENSOR_PROBE
     #define TEMP_PROBE_PIN            TEMP_1_PIN
   #elif TEMP_SENSOR_CHAMBER

Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h

@@ -165,8 +165,8 @@
 //
 #define TEMP_0_PIN                         P0_24
 #define TEMP_1_PIN                         P0_23
-//#define TEMP_2_PIN                       P1_30  // Onboard thermistor
 #define TEMP_BED_PIN                       P0_25
+#define TEMP_BOARD_PIN                     P1_30  // Onboard thermistor, NTC100K
 
 //
 // Heaters / Fans

Marlin/src/pins/rambo/pins_EINSY_RAMBO.h

@@ -114,10 +114,11 @@
 //
 // Temperature Sensors
 //
-#define TEMP_0_PIN                             0  // Analog Input
+#define TEMP_0_PIN                             0  // Analog Input, Header J2
-#define TEMP_1_PIN                             1  // Analog Input
+#define TEMP_1_PIN                             1  // Analog Input, Header J3
-#define TEMP_BED_PIN                           2  // Analog Input
+#define TEMP_BOARD_PIN                TEMP_1_PIN  // Analog Input, Header J3
-#define TEMP_PROBE_PIN                         3  // Analog Input
+#define TEMP_BED_PIN                           2  // Analog Input, Header J6
+#define TEMP_PROBE_PIN                         3  // Analog Input, Header J15
 
 //
 // Heaters / Fans

Marlin/src/pins/sam/pins_DUE3DOM_MINI.h

@@ -68,8 +68,8 @@
 //
 #define TEMP_0_PIN                             0  // Analog Input (HOTEND0 thermistor)
 #define TEMP_1_PIN                             2  // Analog Input (unused)
-#define TEMP_2_PIN                             5  // Analog Input (OnBoard thermistor beta 3950)
 #define TEMP_BED_PIN                           1  // Analog Input (BED thermistor)
+#define TEMP_BOARD_PIN                         5  // Analog Input (OnBoard thermistor beta 3950)
 
 // SPI for MAX Thermocouple
 #if DISABLED(SDSUPPORT)

Marlin/src/pins/stm32f4/pins_BTT_BTT002_V1_0.h

@@ -161,6 +161,7 @@
 //
 #define TEMP_0_PIN                          PA2   // T0 <-> E0
 #define TEMP_1_PIN                          PA0   // T1 <-> E1
+#define TEMP_BOARD_PIN               TEMP_1_PIN   // Onboard sensor shared with T1
 #define TEMP_BED_PIN                        PA1   // T2 <-> Bed
 #define TEMP_PROBE_PIN                      PC3   // Shares J4 connector with PD1