From 330b981912cc755d0d76e4982f267be767c35168 Mon Sep 17 00:00:00 2001 From: Michael Henke Date: Fri, 24 Feb 2017 19:40:47 -0800 Subject: [PATCH] created Configuration.h and Configuration_adv.h for the kossel mini sold by flsun --- .../delta/flsun_kossel_mini/Configuration.h | 1565 +++++++++++++++++ .../flsun_kossel_mini/Configuration_adv.h | 1103 ++++++++++++ 2 files changed, 2668 insertions(+) create mode 100644 Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h create mode 100644 Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h new file mode 100644 index 0000000000..6ad573a12c --- /dev/null +++ b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h @@ -0,0 +1,1565 @@ +/** + Marlin 3D Printer Firmware + Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + + Based on Sprinter and grbl. + Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 3 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see . + +*/ + +/** + Configuration.h + + Basic settings such as: + + - Type of electronics + - Type of temperature sensor + - Printer geometry + - Endstop configuration + - LCD controller + - Extra features + + Advanced settings can be found in Configuration_adv.h + +*/ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +/** + + * *********************************** + * ** ATTENTION TO ALL DEVELOPERS ** + * *********************************** + + You must increment this version number for every significant change such as, + but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option. + + Note: Update also Version.h ! +*/ +#define CONFIGURATION_H_VERSION 010100 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + Here are some standard links for getting your machine calibrated: + + http://reprap.org/wiki/Calibration + http://youtu.be/wAL9d7FgInk + http://calculator.josefprusa.cz + http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + http://www.thingiverse.com/thing:5573 + https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + http://www.thingiverse.com/thing:298812 +*/ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer replace the configuration files with the files in the +// example_configurations/delta directory. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a Scara printer replace the configuration files with the files in the +// example_configurations/SCARA directory. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(Michael Henke, flsun Kossel Mini)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +// +// *** VENDORS PLEASE READ ***************************************************** +// +// Marlin now allow you to have a vendor boot image to be displayed on machine +// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your +// custom boot image and then the default Marlin boot image is shown. +// +// We suggest for you to take advantage of this new feature and keep the Marlin +// boot image unmodified. For an example have a look at the bq Hephestos 2 +// example configuration folder. +// +//#define SHOW_CUSTOM_BOOTSCREEN +// @section machine + +/** + Select which serial port on the board will be used for communication with the host. + This allows the connection of wireless adapters (for instance) to non-default port pins. + Serial port 0 is always used by the Arduino bootloader regardless of this setting. + + :[0, 1, 2, 3, 4, 5, 6, 7] +*/ +#define SERIAL_PORT 0 + +/** + This setting determines the communication speed of the printer. + + 250000 works in most cases, but you might try a lower speed if + you commonly experience drop-outs during host printing. + + :[2400, 9600, 19200, 38400, 57600, 115200, 250000] +*/ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD +#define MOTHERBOARD BOARD_RAMPS_13_EFB +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +#define CUSTOM_MACHINE_NAME "Mini Kossel" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +// :[1, 2, 3, 4] +#define EXTRUDERS 1 + +// Enable if your E steppers or extruder gear ratios are not identical +//#define DISTINCT_E_FACTORS + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +// A dual extruder that uses a single stepper motor +// Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) +#define SWITCHING_EXTRUDER_SERVO_NR 0 +#define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 +//#define HOTEND_OFFSET_Z {0.0, 0.0} +#endif + +/** + "Mixing Extruder" + - Adds a new code, M165, to set the current mix factors. + - Extends the stepping routines to move multiple steppers in proportion to the mix. + - Optional support for Repetier Host M163, M164, and virtual extruder. + - This implementation supports only a single extruder. + - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation +*/ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) +#define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder +#define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 +//#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +/** + Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + + 0 = No Power Switch + 1 = ATX + 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + + :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } +*/ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 +// Enable this option to leave the PSU off at startup. +// Power to steppers and heaters will need to be turned on with M80. +//#define PS_DEFAULT_OFF +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + + Temperature sensors available: + + -3 : thermocouple with MAX31855 (only for sensor 0) + -2 : thermocouple with MAX6675 (only for sensor 0) + -1 : thermocouple with AD595 + 0 : not used + 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + 3 : Mendel-parts thermistor (4.7k pullup) + 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) + 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + 10 : 100k RS thermistor 198-961 (4.7k pullup) + 11 : 100k beta 3950 1% thermistor (4.7k pullup) + 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + 20 : the PT100 circuit found in the Ultimainboard V2.x + 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + 66 : 4.7M High Temperature thermistor from Dyze Design + 70 : the 100K thermistor found in the bq Hephestos 2 + + 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + (but gives greater accuracy and more stable PID) + 51 : 100k thermistor - EPCOS (1k pullup) + 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + + 1047 : Pt1000 with 4k7 pullup + 1010 : Pt1000 with 1k pullup (non standard) + 147 : Pt100 with 4k7 pullup + 110 : Pt100 with 1k pullup (non standard) + + Use these for Testing or Development purposes. NEVER for production machine. + 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + + :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } +*/ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_BED 1 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 + +// Extruder temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// Bed temperature must be close to target for this long before M190 returns success +#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) +#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#if ENABLED(PIDTEMP) +#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. +//#define PID_DEBUG // Sends debug data to the serial port. +//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX +//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay +//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) +// Set/get with gcode: M301 E[extruder number, 0-2] +#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature +// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. +#define K1 0.95 //smoothing factor within the PID + +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it +// Ultimaker +//#define DEFAULT_Kp 22.2 +//#define DEFAULT_Ki 1.08 +//#define DEFAULT_Kd 114 + +// MakerGear +//#define DEFAULT_Kp 7.0 +//#define DEFAULT_Ki 0.1 +//#define DEFAULT_Kd 12 + +// Mendel Parts V9 on 12V +//#define DEFAULT_Kp 63.0 +//#define DEFAULT_Ki 2.25 +//#define DEFAULT_Kd 440 + +//E3D with 30MM fan +#define DEFAULT_Kp 24.77 +#define DEFAULT_Ki 1.84 +#define DEFAULT_Kd 83.61 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + +//#define PID_BED_DEBUG // Sends debug data to the serial port. + +//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) +//#define DEFAULT_bedKp 10.00 +//#define DEFAULT_bedKi .023 +//#define DEFAULT_bedKd 305.4 + +//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +//#define DEFAULT_bedKp 97.1 +//#define DEFAULT_bedKi 1.41 +//#define DEFAULT_bedKd 1675.16 + +//D-force +#define DEFAULT_bedKp 22.97 +#define DEFAULT_bedKi 3.76 +#define DEFAULT_bedKd 29.2 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP. +// It also enables the M302 command to set the minimum extrusion temperature +// or to allow moving the extruder regardless of the hotend temperature. +// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 175 + +// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 300 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + Thermal Protection protects your printer from damage and fire if a + thermistor falls out or temperature sensors fail in any way. + + The issue: If a thermistor falls out or a temperature sensor fails, + Marlin can no longer sense the actual temperature. Since a disconnected + thermistor reads as a low temperature, the firmware will keep the heater on. + + If you get "Thermal Runaway" or "Heating failed" errors the + details can be tuned in Configuration_adv.h +*/ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +#if ENABLED(DELTA) + +// Make delta curves from many straight lines (linear interpolation). +// This is a trade-off between visible corners (not enough segments) +// and processor overload (too many expensive sqrt calls). +#define DELTA_SEGMENTS_PER_SECOND 160 + +// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + +// Center-to-center distance of the holes in the diagonal push rods. +#define DELTA_DIAGONAL_ROD 218.0 // mm + +// Horizontal offset from middle of printer to smooth rod center. +#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm + +// Horizontal offset of the universal joints on the end effector. +#define DELTA_EFFECTOR_OFFSET 24.0 // mm + +// Horizontal offset of the universal joints on the carriages. +#define DELTA_CARRIAGE_OFFSET 22.0 // mm + +// Horizontal distance bridged by diagonal push rods when effector is centered. +#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) + +// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). +#define DELTA_PRINTABLE_RADIUS 85.0 + +// Delta calibration menu +// uncomment to add three points calibration menu option. +// See http://minow.blogspot.com/index.html#4918805519571907051 +// If needed, adjust the X, Y, Z calibration coordinates +// in ultralcd.cpp@lcd_delta_calibrate_menu() +//#define DELTA_CALIBRATION_MENU + +// After homing move down to a height where XY movement is unconstrained +//#define DELTA_HOME_TO_SAFE_ZONE + +//#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } + +#endif + +// Enable this option for Toshiba steppers +//#define CONFIG_STEPPERS_TOSHIBA + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +//#define USE_XMIN_PLUG +//#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +#define USE_XMAX_PLUG +#define USE_YMAX_PLUG +#define USE_ZMAX_PLUG + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#if DISABLED(ENDSTOPPULLUPS) +// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined +//#define ENDSTOPPULLUP_XMAX +//#define ENDSTOPPULLUP_YMAX +//#define ENDSTOPPULLUP_ZMAX +//#define ENDSTOPPULLUP_XMIN +//#define ENDSTOPPULLUP_YMIN +//#define ENDSTOPPULLUP_ZMIN +//#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +// delta speeds must be the same on xyz +/** + Default Settings + + These settings can be reset by M502 + + You can set distinct factors for each E stepper, if needed. + If fewer factors are given, the last will apply to the rest. + + Note that if EEPROM is enabled, saved values will override these. +*/ + +/** + Default Axis Steps Per Unit (steps/mm) + Override with M92 + X, Y, Z, E0 [, E1[, E2[, E3]]] +*/ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 100, 90 } // default steps per unit for Kossel (GT2, 20 tooth) + +/** + Default Max Feed Rate (mm/s) + Override with M203 + X, Y, Z, E0 [, E1[, E2[, E3]]] +*/ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 200 } + +/** + Default Max Acceleration (change/s) change = mm/s + (Maximum start speed for accelerated moves) + Override with M201 + X, Y, Z, E0 [, E1[, E2[, E3]]] +*/ +#define DEFAULT_MAX_ACCELERATION { 4000, 4000, 4000, 4000 } + +/** + Default Acceleration (change/s) change = mm/s + Override with M204 + + M204 P Acceleration + M204 R Retract Acceleration + M204 T Travel Acceleration +*/ +#define DEFAULT_ACCELERATION 2500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + Default Jerk (mm/s) + + "Jerk" specifies the minimum speed change that requires acceleration. + When changing speed and direction, if the difference is less than the + value set here, it may happen instantaneously. +*/ +#define DEFAULT_XJERK 20.0 +#define DEFAULT_YJERK DEFAULT_XJERK +#define DEFAULT_ZJERK DEFAULT_YJERK // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 + + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use Auto Bed Leveling below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A Fix-Mounted Probe either doesn't deploy or needs manual deployment. +// For example an inductive probe, or a setup that uses the nozzle to probe. +// An inductive probe must be deactivated to go below +// its trigger-point if hardware endstops are active. +#define FIX_MOUNTED_PROBE + +// The BLTouch probe emulates a servo probe. +// The default connector is SERVO 0. Set Z_ENDSTOP_SERVO_NR below to override. +//#define BLTOUCH + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle] + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 2000 +// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z +// Speed for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) +// Use double touch for probing +#define PROBE_DOUBLE_TOUCH + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) +// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, +// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + +// Kossel Mini +#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 +#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS +#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 +#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED + +#define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 +#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS +#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 +#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED/10) + +#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 +#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 +#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z +#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED + +#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 +// Move the probe into position +#define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 +#define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 +#define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 +#define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED +// Move the nozzle down further to push the probe into retracted position. +#define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X +#define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y +#define Z_PROBE_ALLEN_KEY_STOW_2_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z-Z_PROBE_ALLEN_KEY_STOW_DEPTH) +#define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED/10) +// Raise things back up slightly so we don't bump into anything +#define Z_PROBE_ALLEN_KEY_STOW_3_X Z_PROBE_ALLEN_KEY_STOW_2_X +#define Z_PROBE_ALLEN_KEY_STOW_3_Y Z_PROBE_ALLEN_KEY_STOW_2_Y +#define Z_PROBE_ALLEN_KEY_STOW_3_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z+Z_PROBE_ALLEN_KEY_STOW_DEPTH) +#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE (XY_PROBE_SPEED/2) + +#define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0 +#define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0 +#define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z +#define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// + +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Most boards use the X_MAX_PIN by default. +// To use a different pin you can override it here. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +#define Z_MIN_PROBE_PIN Z_MIN_PIN + +// +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +//#define Z_MIN_PROBE_ENDSTOP // A3K leave disable! + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// Enable Z Probe Repeatability test to see how accurate your probe is +#define Z_MIN_PROBE_REPEATABILITY_TEST + +/** + Z probes require clearance when deploying, stowing, and moving between + probe points to avoid hitting the bed and other hardware. + Servo-mounted probes require extra space for the arm to rotate. + Inductive probes need space to keep from triggering early. + + Use these settings to specify the distance (mm) to raise the probe (or + lower the bed). The values set here apply over and above any (negative) + probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + Only integer values >= 1 are valid here. + + Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. +*/ +#define Z_CLEARANCE_DEPLOY_PROBE 50 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points + +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true // DELTA does not invert +#define INVERT_Y_DIR true +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false + +// @section homing + +#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... +// Be sure you have this distance over your Z_MAX_POS in case. + +// ENDSTOP SETTINGS: +// Sets direction of endstops when homing; 1=MAX, -1=MIN +// :[-1, 1] +#define X_HOME_DIR 1 // deltas always home to max +#define Y_HOME_DIR 1 +#define Z_HOME_DIR 1 + +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. + +// @section machine + +// Travel limits after homing (units are in mm) +#define X_MIN_POS -(DELTA_PRINTABLE_RADIUS) +#define Y_MIN_POS -(DELTA_PRINTABLE_RADIUS) +#define Z_MIN_POS 0 +#define X_MAX_POS DELTA_PRINTABLE_RADIUS +#define Y_MAX_POS DELTA_PRINTABLE_RADIUS +#define Z_MAX_POS MANUAL_Z_HOME_POS + +//=========================================================================== +//========================= Filament Runout Sensor ========================== +//=========================================================================== +//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament +// RAMPS-based boards use SERVO3_PIN. For other boards you may need to define FIL_RUNOUT_PIN. +// It is assumed that when logic high = filament available +// when logic low = filament ran out +#if ENABLED(FILAMENT_RUNOUT_SENSOR) +#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. +#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. +#define FILAMENT_RUNOUT_SCRIPT "M600" +#endif + +//=========================================================================== +//============================ Mesh Bed Leveling ============================ +//=========================================================================== +// +// MESH_BED_LEVELING does not yet support DELTA printers. +//#define MESH_BED_LEVELING // Enable mesh bed leveling. + +#if ENABLED(MESH_BED_LEVELING) +#define MESH_INSET 10 // Mesh inset margin on print area +#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. +#define MESH_NUM_Y_POINTS 3 +#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. + +#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] + +#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. + +#if ENABLED(MANUAL_BED_LEVELING) +#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. +#endif // MANUAL_BED_LEVELING + +// Gradually reduce leveling correction until a set height is reached, +// at which point movement will be level to the machine's XY plane. +// The height can be set with M420 Z +#define ENABLE_LEVELING_FADE_HEIGHT + +#endif // MESH_BED_LEVELING + +//=========================================================================== +//============================ Auto Bed Leveling ============================ +//=========================================================================== +// @section bedlevel + +/** + Select one form of Auto Bed Leveling below. + + If you're also using the Probe for Z Homing, it's + highly recommended to enable Z_SAFE_HOMING also! + + - 3POINT + Probe 3 arbitrary points on the bed (that aren't collinear) + You specify the XY coordinates of all 3 points. + The result is a single tilted plane. Best for a flat bed. + + - LINEAR + Probe several points in a grid. + You specify the rectangle and the density of sample points. + The result is a single tilted plane. Best for a flat bed. + + - BILINEAR + Probe several points in a grid. + You specify the rectangle and the density of sample points. + The result is a mesh, best for large or uneven beds. +*/ +//#define AUTO_BED_LEVELING_3POINT // Only AUTO_BED_LEVELING_BILINEAR is supported for DELTA bed leveling. +//#define AUTO_BED_LEVELING_LINEAR // Only AUTO_BED_LEVELING_BILINEAR is supported for DELTA bed leveling. +#define AUTO_BED_LEVELING_BILINEAR // Only AUTO_BED_LEVELING_BILINEAR is supported for DELTA bed leveling. + +/** + Enable detailed logging of G28, G29, M48, etc. + Turn on with the command 'M111 S32'. + NOTE: Requires a lot of PROGMEM! +*/ +//#define DEBUG_LEVELING_FEATURE + +#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + // Works best with 5 or more points in each dimension. + #define ABL_GRID_POINTS_X 9 + #define ABL_GRID_POINTS_Y ABL_GRID_POINTS_X + +// Set the boundaries for probing (where the probe can reach). +#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 15) +#define LEFT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) +#define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS +#define FRONT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) +#define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS + +// The Z probe minimum outer margin (to validate G29 parameters). +#define MIN_PROBE_EDGE 10 + +// Probe along the Y axis, advancing X after each column +//#define PROBE_Y_FIRST + +#if ENABLED(AUTO_BED_LEVELING_BILINEAR) + +// Gradually reduce leveling correction until a set height is reached, +// at which point movement will be level to the machine's XY plane. +// The height can be set with M420 Z +#define ENABLE_LEVELING_FADE_HEIGHT + +// +// Experimental Subdivision of the grid by Catmull-Rom method. +// Synthesizes intermediate points to produce a more detailed mesh. +// +//#define ABL_BILINEAR_SUBDIVISION +#if ENABLED(ABL_BILINEAR_SUBDIVISION) +// Number of subdivisions between probe points +#define BILINEAR_SUBDIVISIONS 3 +#endif + +#endif + +#elif ENABLED(AUTO_BED_LEVELING_3POINT) + +// 3 arbitrary points to probe. +// A simple cross-product is used to estimate the plane of the bed. +#define ABL_PROBE_PT_1_X 15 +#define ABL_PROBE_PT_1_Y 180 +#define ABL_PROBE_PT_2_X 15 +#define ABL_PROBE_PT_2_Y 20 +#define ABL_PROBE_PT_3_X 170 +#define ABL_PROBE_PT_3_Y 20 + +#endif + +/** + Commands to execute at the end of G29 probing. + Useful to retract or move the Z probe out of the way. +*/ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +#define MANUAL_Z_HOME_POS (286.5 - 6.5) // Distance between the nozzle to printbed after homing + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +//#define Z_SAFE_HOMING // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. + +#if ENABLED(Z_SAFE_HOMING) +#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28). +#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). +#endif + +// Delta only homes to Z +#define HOMING_FEEDRATE_Z (45*60) + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +#define EEPROM_SETTINGS + +#if ENABLED(EEPROM_SETTINGS) +// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: +#define EEPROM_CHITCHAT // Please keep turned on if you can. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 5 // Number of seconds between "busy" messages. Set with M113. + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 + +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 100 +#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255 + +// +// Nozzle Park -- EXPERIMENTAL +// +// When enabled allows the user to define a special XYZ position, inside the +// machine's topology, to park the nozzle when idle or when receiving the G27 +// command. +// +// The "P" paramenter controls what is the action applied to the Z axis: +// P0: (Default) If current Z-pos is lower than Z-park then the nozzle will +// be raised to reach Z-park height. +// +// P1: No matter the current Z-pos, the nozzle will be raised/lowered to +// reach Z-park height. +// +// P2: The nozzle height will be raised by Z-park amount but never going over +// the machine's limit of Z_MAX_POS. +// +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) +// Specify a park position as { X, Y, Z } +#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } +#endif + +// +// Clean Nozzle Feature -- EXPERIMENTAL +// +// When enabled allows the user to send G12 to start the nozzle cleaning +// process, the G-Code accepts two parameters: +// "P" for pattern selection +// "S" for defining the number of strokes/repetitions +// +// Available list of patterns: +// P0: This is the default pattern, this process requires a sponge type +// material at a fixed bed location, the cleaning process is based on +// "strokes" i.e. back-and-forth movements between the starting and end +// points. +// +// P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T" +// defines the number of zig-zag triangles to be done. "S" defines the +// number of strokes aka one back-and-forth movement. As an example +// sending "G12 P1 S1 T3" will execute: +// +// -- +// | (X0, Y1) | /\ /\ /\ | (X1, Y1) +// | | / \ / \ / \ | +// A | | / \ / \ / \ | +// | | / \ / \ / \ | +// | (X0, Y0) | / \/ \/ \ | (X1, Y0) +// -- +--------------------------------+ +// |________|_________|_________| +// T1 T2 T3 +// +// Caveats: End point Z should use the same value as Start point Z. +// +// Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments +// may change to add new functionality like different wipe patterns. +// +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) +// Number of pattern repetitions +#define NOZZLE_CLEAN_STROKES 12 + +// Specify positions as { X, Y, Z } +#define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} +#define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + +// Moves the nozzle to the initial position +#define NOZZLE_CLEAN_GOBACK +#endif + +// +// Print job timer +// +// Enable this option to automatically start and stop the +// print job timer when M104/M109/M190 commands are received. +// M104 (extruder without wait) - high temp = none, low temp = stop timer +// M109 (extruder with wait) - high temp = start timer, low temp = stop timer +// M190 (bed with wait) - high temp = start timer, low temp = none +// +// In all cases the timer can be started and stopped using +// the following commands: +// +// - M75 - Start the print job timer +// - M76 - Pause the print job timer +// - M77 - Stop the print job timer +#define PRINTJOB_TIMER_AUTOSTART + +// +// Print Counter +// +// When enabled Marlin will keep track of some print statistical data such as: +// - Total print jobs +// - Total successful print jobs +// - Total failed print jobs +// - Total time printing +// +// This information can be viewed by the M78 command. +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +// +// LCD LANGUAGE +// +// Here you may choose the language used by Marlin on the LCD menus, the following +// list of languages are available: +// en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it, +// kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test +// +// :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' } +// +#define LCD_LANGUAGE en + +// +// LCD Character Set +// +// Note: This option is NOT applicable to Graphical Displays. +// +// All character-based LCD's provide ASCII plus one of these +// language extensions: +// +// - JAPANESE ... the most common +// - WESTERN ... with more accented characters +// - CYRILLIC ... for the Russian language +// +// To determine the language extension installed on your controller: +// +// - Compile and upload with LCD_LANGUAGE set to 'test' +// - Click the controller to view the LCD menu +// - The LCD will display Japanese, Western, or Cyrillic text +// +// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language +// +// :['JAPANESE', 'WESTERN', 'CYRILLIC'] +// +#define DISPLAY_CHARSET_HD44780 WESTERN + +// +// LCD TYPE +// +// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2, +// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels +// (ST7565R family). (This option will be set automatically for certain displays.) +// +// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display! +// https://github.com/olikraus/U8glib_Arduino +// +#define ULTRA_LCD // Character based +//#define DOGLCD // Full graphics display + +// +// SD CARD +// +// SD Card support is disabled by default. If your controller has an SD slot, +// you must uncomment the following option or it won't work. +// +#define SDSUPPORT + +// +// SD CARD: SPI SPEED +// +// Uncomment ONE of the following items to use a slower SPI transfer +// speed. This is usually required if you're getting volume init errors. +// +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +// +// SD CARD: ENABLE CRC +// +// Use CRC checks and retries on the SD communication. +// +//#define SD_CHECK_AND_RETRY + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 1 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 5 + +/** + Encoder Direction Options + + Test your encoder's behavior first with both options disabled. + + Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + Reversed Value Editing only? Enable BOTH options. +*/ + +// +// This option reverses the encoder direction everywhere +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +// INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics. +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 + +// +// CONTROLLER TYPE: Standard +// +// Marlin supports a wide variety of controllers. +// Enable one of the following options to specify your controller. +// + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart YW Robot (LCM1602) LCD Display +// +//#define LCD_I2C_SAINSMART_YWROBOT + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) +//#define U8GLIB_SSD1306 +#define U8GLIB_SH1106 +#endif + +// +// CONTROLLER TYPE: Shift register panels +// +// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Otherwise the RED led is on. There is 1C hysteresis. +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +//#define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +// Support for an RGB LED using 3 separate pins with optional PWM +//#define RGB_LED +#if ENABLED(RGB_LED) +#define RGB_LED_R_PIN 34 +#define RGB_LED_G_PIN 43 +#define RGB_LED_B_PIN 35 +#endif + +/*********************************************************************\ + R/C SERVO support + Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY 300 + +// Servo deactivation +// +// With this option servos are powered only during movement, then turned off to prevent jitter. +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +/**********************************************************************\ + Support for a filament diameter sensor + Also allows adjustment of diameter at print time (vs at slicing) + Single extruder only at this point (extruder 0) + + Motherboards + 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector + 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) + 301 - Rambo - uses Analog input 3 + Note may require analog pins to be defined for different motherboards + **********************************************************************/ +// Uncomment below to enable +//#define FILAMENT_WIDTH_SENSOR + +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation + +#if ENABLED(FILAMENT_WIDTH_SENSOR) +#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) +#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + +#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm +#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + +//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. +//#define FILAMENT_LCD_DISPLAY +#endif + +#endif // CONFIGURATION_H diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h new file mode 100644 index 0000000000..447fe136a2 --- /dev/null +++ b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h @@ -0,0 +1,1103 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#ifndef CONFIGURATION_ADV_H +#define CONFIGURATION_ADV_H + +/** + * + * *********************************** + * ** ATTENTION TO ALL DEVELOPERS ** + * *********************************** + * + * You must increment this version number for every significant change such as, + * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option. + * + * Note: Update also Version.h ! + */ +#define CONFIGURATION_ADV_H_VERSION 010100 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + /** + * Whenever an M104 or M109 increases the target temperature the firmware will wait for the + * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE + * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109, + * but only if the current temperature is far enough below the target for a reliable test. + * + * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE + * WATCH_TEMP_INCREASE should not be below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * Whenever an M140 or M190 increases the target temperature the firmware will wait for the + * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE + * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190, + * but only if the current temperature is far enough below the target for a reliable test. + * + * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease + * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.) + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // this adds an experimental additional term to the heating power, proportional to the extrusion speed. + // if Kc is chosen well, the additional required power due to increased melting should be compensated. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +//Show Temperature ADC value +//The M105 command return, besides traditional information, the ADC value read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m + #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm +#endif + +// @section temperature + +//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements. +//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET" +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 + +//This is for controlling a fan to cool down the stepper drivers +//it will turn on when any driver is enabled +//and turn off after the set amount of seconds from last driver being disabled again +#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable) +#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run +#define CONTROLLERFAN_SPEED 255 // == full speed + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +// This defines the minimal speed for the main fan, run in PWM mode +// to enable uncomment and set minimal PWM speed for reliable running (1-255) +// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM +//#define FAN_MIN_PWM 50 + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + +// Define a pin to turn case light on/off +//#define CASE_LIGHT_PIN 4 +#if PIN_EXISTS(CASE_LIGHT) + #define INVERT_CASE_LIGHT false // Set to true if HIGH is the OFF state (active low) + //#define CASE_LIGHT_DEFAULT_ON // Uncomment to set default state to on + //#define MENU_ITEM_CASE_LIGHT // Uncomment to have a Case Light On / Off entry in main menu +#endif + +//=========================================================================== +//============================ Mechanical Settings ========================== +//=========================================================================== + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Dual X Steppers +// Uncomment this option to drive two X axis motors. +// The next unused E driver will be assigned to the second X stepper. +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + // Set true if the two X motors need to rotate in opposite directions + #define INVERT_X2_VS_X_DIR true +#endif + + +// Dual Y Steppers +// Uncomment this option to drive two Y axis motors. +// The next unused E driver will be assigned to the second Y stepper. +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + // Set true if the two Y motors need to rotate in opposite directions + #define INVERT_Y2_VS_Y_DIR true +#endif + +// A single Z stepper driver is usually used to drive 2 stepper motors. +// Uncomment this option to use a separate stepper driver for each Z axis motor. +// The next unused E driver will be assigned to the second Z stepper. +//#define Z_DUAL_STEPPER_DRIVERS + +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + + // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // There is also an implementation of M666 (software endstops adjustment) to this feature. + // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. + // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. + // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. + // Play a little bit with small adjustments (0.5mm) and check the behaviour. + // The M119 (endstops report) will start reporting the Z2 Endstop as well. + + //#define Z_DUAL_ENDSTOPS + + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #endif + +#endif // Z_DUAL_STEPPER_DRIVERS + +// Enable this for dual x-carriage printers. +// A dual x-carriage design has the advantage that the inactive extruder can be parked which +// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage +// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug. +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + // Configuration for second X-carriage + // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop; + // the second x-carriage always homes to the maximum endstop. + #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage + #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // There are a few selectable movement modes for dual x-carriages using M605 S + // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE + + // Default settings in "Auto-park Mode" + #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder + #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif //DUAL_X_CARRIAGE + +// @section homing + +//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 5 // deltas need the same for all three axis +#define HOMING_BUMP_DIVISOR {10, 10, 10} // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// @section machine + +#define AXIS_RELATIVE_MODES {false, false, false, false} + +// Allow duplication mode with a basic dual-nozzle extruder +//#define DUAL_NOZZLE_DUPLICATION_MODE + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 60 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +// @section lcd + +#if ENABLED(ULTIPANEL) + #define MANUAL_FEEDRATE_XYZ 50*60 + #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) +//#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec) + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16] + +// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards) +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) + +// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current) +//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps + +// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro +//#define DIGIPOT_I2C +// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8 +#define DIGIPOT_I2C_NUM_CHANNELS 8 +// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS +#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value + +//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ +#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again + +// @section lcd + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. + + #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order. + // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that. + // using: + //#define MENU_ADDAUTOSTART + + // Show a progress bar on HD44780 LCDs for SD printing + //#define LCD_PROGRESS_BAR + + #if ENABLED(LCD_PROGRESS_BAR) + // Amount of time (ms) to show the bar + #define PROGRESS_BAR_BAR_TIME 2000 + // Amount of time (ms) to show the status message + #define PROGRESS_BAR_MSG_TIME 3000 + // Amount of time (ms) to retain the status message (0=forever) + #define PROGRESS_MSG_EXPIRE 0 + // Enable this to show messages for MSG_TIME then hide them + //#define PROGRESS_MSG_ONCE + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // This option allows you to abort SD printing when any endstop is triggered. + // This feature must be enabled with "M540 S1" or from the LCD menu. + // To have any effect, endstops must be enabled during SD printing. + //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + +#endif // SDSUPPORT + +// Some additional options are available for graphical displays: +#if ENABLED(DOGLCD) + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 +#endif // DOGLCD + +// @section safety + +// The hardware watchdog should reset the microcontroller disabling all outputs, +// in case the firmware gets stuck and doesn't do temperature regulation. +#define USE_WATCHDOG + +#if ENABLED(USE_WATCHDOG) + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process +// it can e.g. be used to change z-positions in the print startup phase in real-time +// does not respect endstops! +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + #define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions + //not implemented for deltabots! + #define BABYSTEP_INVERT_Z false //true for inverse movements in Z + #define BABYSTEP_MULTIPLICATOR 1 //faster movements +#endif + +// +// Ensure Smooth Moves +// +// Enable this option to prevent the machine from stuttering when printing multiple short segments. +// This feature uses two strategies to eliminate stuttering: +// +// 1. During short segments a Graphical LCD update may take so much time that the planner buffer gets +// completely drained. When this happens pauses are introduced between short segments, and print moves +// will become jerky until a longer segment provides enough time for the buffer to be filled again. +// This jerkiness negatively affects print quality. The ENSURE_SMOOTH_MOVES option addresses the issue +// by pausing the LCD until there's enough time to safely update. +// +// NOTE: This will cause the Info Screen to lag and controller buttons may become unresponsive. +// Enable ALWAYS_ALLOW_MENU to keep the controller responsive. +// +// 2. No block is allowed to take less time than MIN_BLOCK_TIME. That's the time it takes in the main +// loop to add a new block to the buffer, check temperatures, etc., including all blocked time due to +// interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from +// draining. +// +//#define ENSURE_SMOOTH_MOVES +#if ENABLED(ENSURE_SMOOTH_MOVES) + //#define ALWAYS_ALLOW_MENU // If enabled, the menu will always be responsive. + // WARNING: Menu navigation during short moves may cause stuttering! + #define LCD_UPDATE_THRESHOLD 135 // (ms) Minimum duration for the current segment to allow an LCD update. + // Default value is good for graphical LCDs (e.g., REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER). + // You may try to lower this value until you printer starts stuttering again as if ENSURE_SMOOTH_MOVES is disabled. + #define MIN_BLOCK_TIME 6 // (ms) Minimum duration of a single block. You shouldn't need to modify this. +#endif + +// @section extruder + +// extruder advance constant (s2/mm3) +// +// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2 +// +// Hooke's law says: force = k * distance +// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant +// so: v ^ 2 is proportional to number of steps we advance the extruder +//#define ADVANCE + +#if ENABLED(ADVANCE) + #define EXTRUDER_ADVANCE_K .0 + #define D_FILAMENT 2.85 +#endif + +/** + * Implementation of linear pressure control + * + * Assumption: advance = k * (delta velocity) + * K=0 means advance disabled. + * To get a rough start value for calibration, measure your "free filament length" + * between the hobbed bolt and the nozzle (in cm). Use the formula below that fits + * your setup, where L is the "free filament length": + * + * Filament diameter | 1.75mm | 3.0mm | + * ----------------------------|-----------|------------| + * Stiff filament (PLA) | K=47*L/10 | K=139*L/10 | + * Softer filament (ABS, nGen) | K=88*L/10 | K=260*L/10 | + */ +//#define LIN_ADVANCE + +#if ENABLED(LIN_ADVANCE) + #define LIN_ADVANCE_K 75 +#endif + +// @section leveling + +// Default mesh area is an area with an inset margin on the print area. +// Below are the macros that are used to define the borders for the mesh area, +// made available here for specialized needs, ie dual extruder setup. +#if ENABLED(MESH_BED_LEVELING) + #define MESH_MIN_X (X_MIN_POS + MESH_INSET) + #define MESH_MAX_X (X_MAX_POS - (MESH_INSET)) + #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET) + #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET)) +#endif + +// @section extras + +// Arc interpretation settings: +#define ARC_SUPPORT // Disabling this saves ~2738 bytes +#define MM_PER_ARC_SEGMENT 1 +#define N_ARC_CORRECTION 25 + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +// G38.2 and G38.3 Probe Target +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +// The minimum pulse width (in µs) for stepping a stepper. +// Set this if you find stepping unreliable, or if using a very fast CPU. +#define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transfer Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// @section fwretract + +// Firmware based and LCD controlled retract +// M207 and M208 can be used to define parameters for the retraction. +// The retraction can be called by the slicer using G10 and G11 +// until then, intended retractions can be detected by moves that only extrude and the direction. +// the moves are than replaced by the firmware controlled ones. + +//#define FWRETRACT //ONLY PARTIALLY TESTED +#if ENABLED(FWRETRACT) + #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt + #define RETRACT_LENGTH 3 //default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s) + #define RETRACT_ZLIFT 0 //default retract Z-lift + #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) +#endif + +// Add support for experimental filament exchange support M600; requires display +#if ENABLED(ULTIPANEL) + // #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too) + #if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS 3 // X position of hotend + #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter lenght for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #endif +#endif + +/******************************************************************************\ + * enable this section if you have TMC26X motor drivers. + * you need to import the TMC26XStepper library into the Arduino IDE for this + ******************************************************************************/ + +// @section tmc + +//#define HAVE_TMCDRIVER +#if ENABLED(HAVE_TMCDRIVER) + + //#define X_IS_TMC + //#define X2_IS_TMC + //#define Y_IS_TMC + //#define Y2_IS_TMC + //#define Z_IS_TMC + //#define Z2_IS_TMC + //#define E0_IS_TMC + //#define E1_IS_TMC + //#define E2_IS_TMC + //#define E3_IS_TMC + + #define X_MAX_CURRENT 1000 // in mA + #define X_SENSE_RESISTOR 91 // in mOhms + #define X_MICROSTEPS 16 // number of microsteps + + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + +#endif + +// @section TMC2130 + + +/** + * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers. + * + * To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library + * (https://github.com/makertum/Trinamic_TMC2130). + * + * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to + * the hardware SPI interface on your board and define the required CS pins + * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + */ + +//#define HAVE_TMC2130DRIVER + +#if ENABLED(HAVE_TMC2130DRIVER) + + //#define TMC2130_ADVANCED_CONFIGURATION + + // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY + //#define X_IS_TMC2130 + //#define X2_IS_TMC2130 + //#define Y_IS_TMC2130 + //#define Y2_IS_TMC2130 + //#define Z_IS_TMC2130 + //#define Z2_IS_TMC2130 + //#define E0_IS_TMC2130 + //#define E1_IS_TMC2130 + //#define E2_IS_TMC2130 + //#define E3_IS_TMC2130 + + #if ENABLED(TMC2130_ADVANCED_CONFIGURATION) + + // If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below. + // Enabled settings will be automatically applied to all axes specified above. + // + // Please read the TMC2130 datasheet: + // http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf + // All settings here have the same (sometimes cryptic) names as in the datasheet. + // + // The following, uncommented settings are only suggestion. + + /* GENERAL CONFIGURATION */ + + //#define GLOBAL_EN_PWM_MODE 0 + #define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN + //#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal + #define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold + //#define GLOBAL_ENC_COMMUTATION 0 // [0,1] + #define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert + //#define GLOBAL_DIAG0_ERROR 0 // [0,1] + //#define GLOBAL_DIAG0_OTPW 0 // [0,1] + //#define GLOBAL_DIAG0_STALL 0 // [0,1] + //#define GLOBAL_DIAG1_STALL 0 // [0,1] + //#define GLOBAL_DIAG1_INDEX 0 // [0,1] + //#define GLOBAL_DIAG1_ONSTATE 0 // [0,1] + //#define GLOBAL_DIAG1_ONSTATE 0 // [0,1] + //#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1] + //#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1] + //#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1] + //#define GLOBAL_STOP_ENABLE 0 // [0,1] + //#define GLOBAL_DIRECT_MODE 0 // [0,1] + + /* VELOCITY-DEPENDENT DRIVE FEATURES */ + + #define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max + #define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max + #define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds + //#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds + //#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s + //#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s + #define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s + + /* SPI MODE CONFIGURATION */ + + //#define GLOBAL_XDIRECT 0 + + /* DCSTEP MINIMUM VELOCITY */ + + //#define GLOBAL_VDCMIN 0 + + /* MOTOR DRIVER CONFIGURATION*/ + + //#define GLOBAL_DEDGE 0 + //#define GLOBAL_DISS2G 0 + #define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation + #define GLOBAL_MRES 16 // number of microsteps + #define GLOBAL_SYNC 1 // [0-15] + #define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode + #define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities + // #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended) + #define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended + #define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time. + //#define GLOBAL_RNDTF 0 + //#define GLOBAL_DISFDCC 0 + //#define GLOBAL_FD 0 + //#define GLOBAL_HEND 0 + //#define GLOBAL_HSTRT 0 + #define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase + + //#define GLOBAL_SFILT 0 + //#define GLOBAL_SGT 0 + //#define GLOBAL_SEIMIN 0 + //#define GLOBAL_SEDN 0 + //#define GLOBAL_SEMAX 0 + //#define GLOBAL_SEUP 0 + //#define GLOBAL_SEMIN 0 + + //#define GLOBAL_DC_TIME 0 + //#define GLOBAL_DC_SG 0 + + //#define GLOBAL_FREEWHEEL 0 + //#define GLOBAL_PWM_SYMMETRIC 0 + //#define GLOBAL_PWM_AUTOSCALE 0 + //#define GLOBAL_PWM_FREQ 0 + //#define GLOBAL_PWM_GRAD 0 + //#define GLOBAL_PWM_AMPL 0 + + //#define GLOBAL_ENCM_CTRL 0 + + #else + + #define X_IHOLD 31 // [0-31] 0: min, 31: max + #define X_IRUN 31 // [0-31] 0: min, 31: max + #define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds + #define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN + #define X_MRES 16 // number of microsteps + #define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended + #define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase + + #define X2_IHOLD 31 + #define X2_IRUN 31 + #define X2_IHOLDDELAY 15 + #define X2_I_SCALE_ANALOG 1 + #define X2_MRES 16 + #define X2_TBL 1 + #define X2_TOFF 8 + + #define Y_IHOLD 31 + #define Y_IRUN 31 + #define Y_IHOLDDELAY 15 + #define Y_I_SCALE_ANALOG 1 + #define Y_MRES 16 + #define Y_TBL 1 + #define Y_TOFF 8 + + #define Y2_IHOLD 31 + #define Y2_IRUN 31 + #define Y2_IHOLDDELAY 15 + #define Y2_I_SCALE_ANALOG 1 + #define Y2_MRES 16 + #define Y2_TBL 1 + #define Y2_TOFF 8 + + #define Z_IHOLD 31 + #define Z_IRUN 31 + #define Z_IHOLDDELAY 15 + #define Z_I_SCALE_ANALOG 1 + #define Z_MRES 16 + #define Z_TBL 1 + #define Z_TOFF 8 + + #define Z2_IHOLD 31 + #define Z2_IRUN 31 + #define Z2_IHOLDDELAY 15 + #define Z2_I_SCALE_ANALOG 1 + #define Z2_MRES 16 + #define Z2_TBL 1 + #define Z2_TOFF 8 + + #define E0_IHOLD 31 + #define E0_IRUN 31 + #define E0_IHOLDDELAY 15 + #define E0_I_SCALE_ANALOG 1 + #define E0_MRES 16 + #define E0_TBL 1 + #define E0_TOFF 8 + + #define E1_IHOLD 31 + #define E1_IRUN 31 + #define E1_IHOLDDELAY 15 + #define E1_I_SCALE_ANALOG 1 + #define E1_MRES 16 + #define E1_TBL 1 + #define E1_TOFF 8 + + #define E2_IHOLD 31 + #define E2_IRUN 31 + #define E2_IHOLDDELAY 15 + #define E2_I_SCALE_ANALOG 1 + #define E2_MRES 16 + #define E2_TBL 1 + #define E2_TOFF 8 + + #define E3_IHOLD 31 + #define E3_IRUN 31 + #define E3_IHOLDDELAY 15 + #define E3_I_SCALE_ANALOG 1 + #define E3_MRES 16 + #define E3_TBL 1 + #define E3_TOFF 8 + + #endif // TMC2130_ADVANCED_CONFIGURATION + +#endif // HAVE_TMC2130DRIVER + +// @section L6470 + +/** + * Enable this section if you have L6470 motor drivers. + * You need to import the L6470 library into the Arduino IDE for this. + * (https://github.com/ameyer/Arduino-L6470) + */ + +//#define HAVE_L6470DRIVER +#if ENABLED(HAVE_L6470DRIVER) + + //#define X_IS_L6470 + //#define X2_IS_L6470 + //#define Y_IS_L6470 + //#define Y2_IS_L6470 + //#define Z_IS_L6470 + //#define Z2_IS_L6470 + //#define E0_IS_L6470 + //#define E1_IS_L6470 + //#define E2_IS_L6470 + //#define E3_IS_L6470 + + #define X_MICROSTEPS 16 // number of microsteps + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high + #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off + #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall + + #define X2_MICROSTEPS 16 + #define X2_K_VAL 50 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + + #define Y_MICROSTEPS 16 + #define Y_K_VAL 50 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + + #define Y2_MICROSTEPS 16 + #define Y2_K_VAL 50 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + + #define Z_MICROSTEPS 16 + #define Z_K_VAL 50 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + + #define Z2_MICROSTEPS 16 + #define Z2_K_VAL 50 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + + #define E0_MICROSTEPS 16 + #define E0_K_VAL 50 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + + #define E1_MICROSTEPS 16 + #define E1_K_VAL 50 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + + #define E2_MICROSTEPS 16 + #define E2_K_VAL 50 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + + #define E3_MICROSTEPS 16 + #define E3_K_VAL 50 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + +#endif + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +/** + * Add M43 command for pins info and testing + */ +//#define PINS_DEBUGGING + +/** + * Auto-report temperatures with M155 S + */ +//#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +//#define EXTENDED_CAPABILITIES_REPORT + +#endif // CONFIGURATION_ADV_H