Update some outdated configs

Marlin/src/config/examples/MakerParts/Configuration.h

@@ -126,6 +126,15 @@
  */
 #define SERIAL_PORT 0
 
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if avaialble.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 -1
+
 /**
  * This setting determines the communication speed of the printer.
  *
@@ -373,8 +382,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -384,7 +394,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
@@ -465,12 +474,13 @@
 //===========================================================================
 
 /**
- * Thermal Protection protects your printer from damage and fire if a
+ * Thermal Protection provides additional protection to your printer from damage
- * thermistor falls out or temperature sensors fail in any way.
+ * and fire. Marlin always includes safe min and max temperature ranges which
+ * protect against a broken or disconnected thermistor wire.
  *
- * The issue: If a thermistor falls out or a temperature sensor fails,
+ * The issue: If a thermistor falls out, it will report the much lower
- * Marlin can no longer sense the actual temperature. Since a disconnected
+ * temperature of the air in the room, and the the firmware will keep
- * thermistor reads as a low temperature, the firmware will keep the heater on.
+ * the heater on.
  *
  * If you get "Thermal Runaway" or "Heating failed" errors the
  * details can be tuned in Configuration_adv.h
@@ -723,14 +733,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
+// The number of probes to perform at each point.
-//#define PROBE_DOUBLE_TOUCH
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
@@ -920,7 +932,8 @@
   #define ENABLE_LEVELING_FADE_HEIGHT
 
   // For Cartesian machines, instead of dividing moves on mesh boundaries,
-  // split up moves into short segments like a Delta.
+  // split up moves into short segments like a Delta. This follows the
+  // contours of the bed more closely than edge-to-edge straight moves.
   #define SEGMENT_LEVELED_MOVES
   #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
 

Marlin/src/config/examples/stm32f103ret6/Configuration.h

@@ -100,19 +100,29 @@
 /**
  * Select the serial port on the board to use for communication with the host.
  * This allows the connection of wireless adapters (for instance) to non-default port pins.
- * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
+ * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  *
- * :[0, 1, 2, 3, 4, 5, 6, 7]
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
 #define SERIAL_PORT 0
 
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if avaialble.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 -1
+
 /**
  * This setting determines the communication speed of the printer.
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
@@ -139,6 +149,9 @@
 // :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+
 // For Cyclops or any "multi-extruder" that shares a single nozzle.
 //#define SINGLENOZZLE
 
@@ -179,6 +192,21 @@
   //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
 #endif
 
+/**
+ * Two separate X-carriages with extruders that connect to a moving part
+ * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
+ */
+//#define PARKING_EXTRUDER
+#if ENABLED(PARKING_EXTRUDER)
+  #define PARKING_EXTRUDER_SOLENOIDS_INVERT           // If enabled, the solenoid is NOT magnetized with applied voltage
+  #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW  // LOW or HIGH pin signal energizes the coil
+  #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250        // Delay (ms) for magnetic field. No delay if 0 or not defined.
+  #define PARKING_EXTRUDER_PARKING_X { -78, 184 }     // X positions for parking the extruders
+  #define PARKING_EXTRUDER_GRAB_DISTANCE 1            // mm to move beyond the parking point to grab the extruder
+  #define PARKING_EXTRUDER_SECURITY_RAISE 5           // Z-raise before parking
+  #define HOTEND_OFFSET_Z { 0.0, 1.3 }                // Z-offsets of the two hotends. The first must be 0.
+#endif
+
 /**
  * "Mixing Extruder"
  *   - Adds a new code, M165, to set the current mix factors.
@@ -335,8 +363,9 @@
 
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
-#define BANG_MAX 180 // limits current to nozzle while in bang-bang mode; 255=full current
+#define BANG_MAX 180     // Limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
   #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
   //#define PID_DEBUG // Sends debug data to the serial port.
@@ -346,7 +375,6 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
-  #define K1 0.95 //smoothing factor within the PID
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
@@ -427,12 +455,13 @@
 //===========================================================================
 
 /**
- * Thermal Protection protects your printer from damage and fire if a
+ * Thermal Protection provides additional protection to your printer from damage
- * thermistor falls out or temperature sensors fail in any way.
+ * and fire. Marlin always includes safe min and max temperature ranges which
+ * protect against a broken or disconnected thermistor wire.
  *
- * The issue: If a thermistor falls out or a temperature sensor fails,
+ * The issue: If a thermistor falls out, it will report the much lower
- * Marlin can no longer sense the actual temperature. Since a disconnected
+ * temperature of the air in the room, and the the firmware will keep
- * thermistor reads as a low temperature, the firmware will keep the heater on.
+ * the heater on.
  *
  * If you get "Thermal Runaway" or "Heating failed" errors the
  * details can be tuned in Configuration_adv.h
@@ -567,14 +596,13 @@
 #define DEFAULT_ZJERK                  0.3
 #define DEFAULT_EJERK                  5.0
 
-
 //===========================================================================
 //============================= Z Probe Options =============================
 //===========================================================================
 // @section probes
 
 //
-// See http://marlinfw.org/configuration/probes.html
+// See http://marlinfw.org/docs/configuration/probes.html
 //
 
 /**
@@ -609,7 +637,7 @@
  * Probe Type
  *
  * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- * You must activate one of these to use Auto Bed Leveling below.
+ * Activate one of these to use Auto Bed Leveling below.
  */
 
 /**
@@ -640,11 +668,11 @@
 #endif
 
 /**
- * Enable if probing seems unreliable. Heaters and/or fans - consistent with the
+ * Enable one or more of the following if probing seems unreliable.
- * options selected below - will be disabled during probing so as to minimize
+ * Heaters and/or fans can be disabled during probing to minimize electrical
- * potential EM interference by quieting/silencing the source of the 'noise' (the change
+ * noise. A delay can also be added to allow noise and vibration to settle.
- * in current flowing through the wires).  This is likely most useful to users of the
+ * These options are most useful for the BLTouch probe, but may also improve
- * BLTouch probe, but may also help those with inductive or other probe types.
+ * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 //#define PROBING_FANS_OFF          // Turn fans off when probing
@@ -686,14 +714,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
+// The number of probes to perform at each point.
-//#define PROBE_DOUBLE_TOUCH
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
@@ -760,6 +790,8 @@
 
 // @section homing
 
+//#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
+
 //#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
@@ -783,10 +815,30 @@
 #define Y_MAX_POS Y_BED_SIZE
 #define Z_MAX_POS 180
 
-// If enabled, axes won't move below MIN_POS in response to movement commands.
+/**
+ * Software Endstops
+ *
+ * - Prevent moves outside the set machine bounds.
+ * - Individual axes can be disabled, if desired.
+ * - X and Y only apply to Cartesian robots.
+ * - Use 'M211' to set software endstops on/off or report current state
+ */
+
+// Min software endstops constrain movement within minimum coordinate bounds
 #define MIN_SOFTWARE_ENDSTOPS
-// If enabled, axes won't move above MAX_POS in response to movement commands.
+#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
+  #define MIN_SOFTWARE_ENDSTOP_X
+  #define MIN_SOFTWARE_ENDSTOP_Y
+  #define MIN_SOFTWARE_ENDSTOP_Z
+#endif
+
+// Max software endstops constrain movement within maximum coordinate bounds
 #define MAX_SOFTWARE_ENDSTOPS
+#if ENABLED(MAX_SOFTWARE_ENDSTOPS)
+  #define MAX_SOFTWARE_ENDSTOP_X
+  #define MAX_SOFTWARE_ENDSTOP_Y
+  #define MAX_SOFTWARE_ENDSTOP_Z
+#endif
 
 /**
  * Filament Runout Sensor
@@ -806,7 +858,7 @@
 //===========================================================================
 //=============================== Bed Leveling ==============================
 //===========================================================================
-// @section bedlevel
+// @section calibrate
 
 /**
  * Choose one of the options below to enable G29 Bed Leveling. The parameters
@@ -832,12 +884,7 @@
  * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  *   A comprehensive bed leveling system combining the features and benefits
  *   of other systems. UBL also includes integrated Mesh Generation, Mesh
- *   Validation and Mesh Editing systems. Currently, UBL is only checked out
+ *   Validation and Mesh Editing systems.
- *   for Cartesian Printers. That said, it was primarily designed to correct
- *   poor quality Delta Printers. If you feel adventurous and have a Delta,
- *   please post an issue if something doesn't work correctly. Initially,
- *   you will need to set a reduced bed size so you have a rectangular area
- *   to test on.
  *
  * - MESH_BED_LEVELING
  *   Probe a grid manually
@@ -864,6 +911,24 @@
   // at which point movement will be level to the machine's XY plane.
   // The height can be set with M420 Z<height>
   #define ENABLE_LEVELING_FADE_HEIGHT
+
+  // For Cartesian machines, instead of dividing moves on mesh boundaries,
+  // split up moves into short segments like a Delta. This follows the
+  // contours of the bed more closely than edge-to-edge straight moves.
+  #define SEGMENT_LEVELED_MOVES
+  #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
+
+  /**
+   * Enable the G26 Mesh Validation Pattern tool.
+   */
+  //#define G26_MESH_VALIDATION
+  #if ENABLED(G26_MESH_VALIDATION)
+    #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
+    #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
+    #define MESH_TEST_HOTEND_TEMP  205.0  // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
+    #define MESH_TEST_BED_TEMP      60.0  // (°C) Default bed temperature for the G26 Mesh Validation Tool.
+  #endif
+
 #endif
 
 #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
@@ -919,7 +984,9 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  #define UBL_MESH_INSET 1          // Mesh inset margin on print area
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
+  #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
@@ -930,8 +997,8 @@
   #define UBL_PROBE_PT_3_X 180
   #define UBL_PROBE_PT_3_Y 20
 
-  #define UBL_G26_MESH_VALIDATION   // Enable G26 mesh validation
   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
+  #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
 
 #elif ENABLED(MESH_BED_LEVELING)
 
@@ -958,6 +1025,9 @@
   #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
 #endif
 
+// Add a menu item to move between bed corners for manual bed adjustment
+//#define LEVEL_BED_CORNERS
+
 /**
  * Commands to execute at the end of G29 probing.
  * Useful to retract or move the Z probe out of the way.
@@ -988,14 +1058,71 @@
 //#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
-  #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axis (G28).
+  #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
-  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axis (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
 #endif
 
 // Homing speeds (mm/m)
 #define HOMING_FEEDRATE_XY (50*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
+// @section calibrate
+
+/**
+ * Bed Skew Compensation
+ *
+ * This feature corrects for misalignment in the XYZ axes.
+ *
+ * Take the following steps to get the bed skew in the XY plane:
+ *  1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
+ *  2. For XY_DIAG_AC measure the diagonal A to C
+ *  3. For XY_DIAG_BD measure the diagonal B to D
+ *  4. For XY_SIDE_AD measure the edge A to D
+ *
+ * Marlin automatically computes skew factors from these measurements.
+ * Skew factors may also be computed and set manually:
+ *
+ *  - Compute AB     : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
+ *  - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
+ *
+ * If desired, follow the same procedure for XZ and YZ.
+ * Use these diagrams for reference:
+ *
+ *    Y                     Z                     Z
+ *    ^     B-------C       ^     B-------C       ^     B-------C
+ *    |    /       /        |    /       /        |    /       /
+ *    |   /       /         |   /       /         |   /       /
+ *    |  A-------D          |  A-------D          |  A-------D
+ *    +-------------->X     +-------------->X     +-------------->Y
+ *     XY_SKEW_FACTOR        XZ_SKEW_FACTOR        YZ_SKEW_FACTOR
+ */
+//#define SKEW_CORRECTION
+
+#if ENABLED(SKEW_CORRECTION)
+  // Input all length measurements here:
+  #define XY_DIAG_AC 282.8427124746
+  #define XY_DIAG_BD 282.8427124746
+  #define XY_SIDE_AD 200
+
+  // Or, set the default skew factors directly here
+  // to override the above measurements:
+  #define XY_SKEW_FACTOR 0.0
+
+  //#define SKEW_CORRECTION_FOR_Z
+  #if ENABLED(SKEW_CORRECTION_FOR_Z)
+    #define XZ_DIAG_AC 282.8427124746
+    #define XZ_DIAG_BD 282.8427124746
+    #define YZ_DIAG_AC 282.8427124746
+    #define YZ_DIAG_BD 282.8427124746
+    #define YZ_SIDE_AD 200
+    #define XZ_SKEW_FACTOR 0.0
+    #define YZ_SKEW_FACTOR 0.0
+  #endif
+
+  // Enable this option for M852 to set skew at runtime
+  //#define SKEW_CORRECTION_GCODE
+#endif
+
 //=============================================================================
 //============================= Additional Features ===========================
 //=============================================================================
@@ -1174,11 +1301,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, gl, hr,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
- *    it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk,
+ *    hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
- *    zh_CN, zh_TW, test
+ *    tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
  */
 #define LCD_LANGUAGE en
 
@@ -1200,7 +1327,7 @@
  *  - Click the controller to view the LCD menu
  *  - The LCD will display Japanese, Western, or Cyrillic text
  *
- * See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
+ * See http://marlinfw.org/docs/development/lcd_language.html
  *
  * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  */
@@ -1332,12 +1459,6 @@
 //
 //#define ULTIPANEL
 
-//
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
 //
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -1420,6 +1541,12 @@
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
+//
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
 //
 // ANET and Tronxy Controller supported displays.
 //
@@ -1520,6 +1647,47 @@
 //
 //#define OLED_PANEL_TINYBOY2
 
+//
+// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
+// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
+//
+//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
+
+//
+// MKS MINI12864 with graphic controller and SD support
+// http://reprap.org/wiki/MKS_MINI_12864
+//
+//#define MKS_MINI_12864
+
+//
+// Factory display for Creality CR-10
+// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
+//
+// This is RAMPS-compatible using a single 10-pin connector.
+// (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
+//
+//#define CR10_STOCKDISPLAY
+
+//
+// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
+// http://reprap.org/wiki/MKS_12864OLED
+//
+// Tiny, but very sharp OLED display
+//
+//#define MKS_12864OLED          // Uses the SH1106 controller (default)
+//#define MKS_12864OLED_SSD1306  // Uses the SSD1306 controller
+
+//
+// AZSMZ 12864 LCD with SD
+// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
+//
+//#define AZSMZ_12864
+
+// Silvergate GLCD controller
+// http://github.com/android444/Silvergate
+//
+//#define SILVER_GATE_GLCD_CONTROLLER
+
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================
@@ -1576,16 +1744,22 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED an overall brightness parameter is also available.
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  NOTE: A separate 5V power supply is required! The Neopixel LED needs
+ *  more current than the Arduino 5V linear regulator can produce.
  * *** CAUTION ***
  *
+ * LED Type. Enable only one of the following two options.
+ *
  */
 //#define RGB_LED
 //#define RGBW_LED
+
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
   #define RGB_LED_R_PIN 34
   #define RGB_LED_G_PIN 43
@@ -1594,11 +1768,14 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
+//#define NEOPIXEL_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(NEOPIXEL_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
+  #define NEOPIXEL_TYPE   NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
-  #define NEOPIXEL_PIXELS 3
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
-  //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
+  #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
+  //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
 /**
@@ -1612,67 +1789,32 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 
-/*********************************************************************\
+/**
-* R/C SERVO support
+ * R/C SERVO support
-* Sponsored by TrinityLabs, Reworked by codexmas
+ * Sponsored by TrinityLabs, Reworked by codexmas
-**********************************************************************/
+ */
 
-// Number of servos
+/**
-//
+ * Number of servos
-// If you select a configuration below, this will receive a default value and does not need to be set manually
+ *
-// set it manually if you have more servos than extruders and wish to manually control some
+ * For some servo-related options NUM_SERVOS will be set automatically.
-// leaving it undefined or defining as 0 will disable the servo subsystem
+ * Set this manually if there are extra servos needing manual control.
-// If unsure, leave commented / disabled
+ * Leave undefined or set to 0 to entirely disable the servo subsystem.
-//
+ */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
 // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
-#define SERVO_DELAY 300
+#define SERVO_DELAY { 300 }
 
 // Servo deactivation
 //
 // With this option servos are powered only during movement, then turned off to prevent jitter.
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- *  34 RAMPS_14    : Analog input 5 on the AUX2 connector
- *  81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO       : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
-  #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
-  #define MEASUREMENT_DELAY_CM        14    // (cm) The distance from the filament sensor to the melting chamber
-
-  #define FILWIDTH_ERROR_MARGIN        1.0  // (mm) If a measurement differs too much from nominal width ignore it
-  #define MAX_MEASUREMENT_DELAY       20    // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
-  #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
-  // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
-  //#define FILAMENT_LCD_DISPLAY
-#endif
-
 #endif // CONFIGURATION_H