Sanity checks for FILAMENT_CHANGE_FEATURE and FILAMENT_RUNOUT_SCRIPT

Marlin/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/SanityCheck.h

@@ -244,14 +244,20 @@
     #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
   #elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
     #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
+  #elif DISABLED(FILAMENT_CHANGE_FEATURE)
+    static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "FILAMENT_CHANGE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
   #endif
 #endif
 
 /**
  * Filament Change with Extruder Runout Prevention
  */
-#if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
-  #error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #if DISABLED(ULTIPANEL)
+    #error "FILAMENT_CHANGE_FEATURE currently requires an LCD controller."
+  #elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
+    #error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -642,33 +642,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -661,33 +661,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -661,33 +661,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -666,33 +666,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -661,33 +661,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -659,33 +659,38 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
-#if ENABLED(ULTIPANEL)
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
-                                                // 0 to disable unloading for manual unloading
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-                                                // Short or zero length for printers without bowden where loading is not used
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
-                                                // 0 to disable for manual extrusion
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
-                                                // or until outcoming filament color is not clear for filament color change
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
-  #endif
+/**
+ * Filament Change
+ * Experimental filament change support.
+ * Adds the GCode M600 for initiating filament change.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define FILAMENT_CHANGE_FEATURE
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
+                                              // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                              // Short or zero length for printers without bowden where loading is not used
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
 #endif
 
 /******************************************************************************\