mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 12:04:19 +00:00
my local configuration
This commit is contained in:
Michael Moon
parent
5aadc2f5ca
commit
71dc82e0b4
@ -4,8 +4,8 @@
|
||||
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
#define BAUDRATE 250000
|
||||
//#define BAUDRATE 115200
|
||||
//#define BAUDRATE 250000
|
||||
#define BAUDRATE 115200
|
||||
//#define BAUDRATE 230400
|
||||
|
||||
#define EXTRUDERS 1
|
||||
@ -29,7 +29,7 @@
|
||||
// Sanguinololu 1.2 and above = 62
|
||||
// Ultimaker = 7,
|
||||
// Teensylu = 8
|
||||
#define MOTHERBOARD 7
|
||||
#define MOTHERBOARD 99
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
@ -44,36 +44,36 @@
|
||||
// 6 is EPCOS 100k
|
||||
// 7 is 100k Honeywell thermistor 135-104LAG-J01
|
||||
|
||||
//#define THERMISTORHEATER_0 3
|
||||
#define THERMISTORHEATER_0 1
|
||||
//#define THERMISTORHEATER_1 1
|
||||
//#define THERMISTORHEATER_2 1
|
||||
|
||||
//#define HEATER_0_USES_THERMISTOR
|
||||
#define HEATER_0_USES_THERMISTOR
|
||||
//#define HEATER_1_USES_THERMISTOR
|
||||
//#define HEATER_2_USES_THERMISTOR
|
||||
#define HEATER_0_USES_AD595
|
||||
//#define HEATER_0_USES_AD595
|
||||
//#define HEATER_1_USES_AD595
|
||||
//#define HEATER_2_USES_AD595
|
||||
|
||||
// Select one of these only to define how the bed temp is read.
|
||||
//#define THERMISTORBED 1
|
||||
//#define BED_USES_THERMISTOR
|
||||
#define THERMISTORBED 1
|
||||
#define BED_USES_THERMISTOR
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
//#define BED_USES_AD595
|
||||
|
||||
#define BED_CHECK_INTERVAL 5000 //ms
|
||||
#define BED_CHECK_INTERVAL 1000 //ms
|
||||
|
||||
//// Heating sanity check:
|
||||
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
|
||||
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
|
||||
// It can be reset with another M104/M109
|
||||
//#define WATCHPERIOD 20000 //20 seconds
|
||||
#define WATCHPERIOD 20000 //20 seconds
|
||||
|
||||
// Actual temperature must be close to target for this long before M109 returns success
|
||||
#define TEMP_RESIDENCY_TIME 30 // (seconds)
|
||||
#define TEMP_RESIDENCY_TIME 50 // (seconds)
|
||||
#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
|
||||
|
||||
//// The minimal temperature defines the temperature below which the heater will not be enabled
|
||||
@ -86,10 +86,10 @@
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_0_MAXTEMP 325
|
||||
//#define HEATER_1_MAXTEMP 275
|
||||
//#define HEATER_2_MAXTEMP 275
|
||||
//#define BED_MAXTEMP 150
|
||||
#define BED_MAXTEMP 140
|
||||
|
||||
|
||||
// Wait for Cooldown
|
||||
@ -103,7 +103,7 @@
|
||||
|
||||
// PID settings:
|
||||
// Uncomment the following line to enable PID support.
|
||||
#define PIDTEMP
|
||||
//#define PIDTEMP
|
||||
#define PID_MAX 255 // limits current to nozzle; 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
@ -167,7 +167,7 @@
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 160
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30.
|
||||
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
@ -209,8 +209,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
//#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders
|
||||
|
||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
@ -223,18 +223,18 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
|
||||
#define min_software_endstops true //If true, axis won't move to coordinates less than zero.
|
||||
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
#define X_MAX_LENGTH 205
|
||||
#define Y_MAX_LENGTH 205
|
||||
#define Z_MAX_LENGTH 200
|
||||
#define X_MAX_LENGTH 187
|
||||
#define Y_MAX_LENGTH 188
|
||||
#define Z_MAX_LENGTH 80
|
||||
|
||||
//// MOVEMENT SETTINGS
|
||||
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
||||
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
|
||||
#define HOMING_FEEDRATE {2400, 2400, 150, 0} // set the homing speeds (mm/min)
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_RETRACT_MM 5
|
||||
#define Y_HOME_RETRACT_MM 5
|
||||
#define Z_HOME_RETRACT_MM 1
|
||||
#define X_HOME_RETRACT_MM 2
|
||||
#define Y_HOME_RETRACT_MM 2
|
||||
#define Z_HOME_RETRACT_MM 2
|
||||
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
@ -243,11 +243,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {64,64,3200,110} // default steps per unit for ultimaker
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 360} //sells mendel with v9 extruder
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 1000} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {1200,1200,100,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
||||
@ -257,7 +257,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_XYJERK 12.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
@ -278,7 +278,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable eeprom support
|
||||
#define EEPROM_SETTINGS
|
||||
//#define EEPROM_SETTINGS
|
||||
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
// please keep turned on if you can.
|
||||
#define EEPROM_CHITCHAT
|
||||
@ -316,9 +316,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
|
||||
//LCD and SD support
|
||||
//#define ULTRA_LCD //general lcd support, also 16x2
|
||||
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
|
||||
#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
#define SD_FINISHED_STEPPERRELEASE false //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M81" // no z because of layer shift.
|
||||
|
||||
//#define ULTIPANEL
|
||||
#ifdef ULTIPANEL
|
||||
@ -358,7 +358,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
#define PREVENT_DANGEROUS_EXTRUDE
|
||||
#define EXTRUDE_MINTEMP 190
|
||||
#define EXTRUDE_MINTEMP 150
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
@ -1,6 +1,49 @@
|
||||
#ifndef PINS_H
|
||||
#define PINS_H
|
||||
|
||||
#if MOTHERBOARD == 99
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#define X_STEP_PIN 2
|
||||
#define X_DIR_PIN 3
|
||||
#define X_ENABLE_PIN -1
|
||||
#define X_MIN_PIN 16
|
||||
#define X_MAX_PIN -1
|
||||
|
||||
#define Y_STEP_PIN 5
|
||||
#define Y_DIR_PIN 6
|
||||
#define Y_ENABLE_PIN -1
|
||||
#define Y_MIN_PIN 67
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 62
|
||||
#define Z_DIR_PIN 63
|
||||
#define Z_ENABLE_PIN -1
|
||||
#define Z_MIN_PIN 59
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 65
|
||||
#define E0_DIR_PIN 66
|
||||
#define E0_ENABLE_PIN -1
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 53
|
||||
#define LED_PIN -1
|
||||
#define FAN_PIN -1
|
||||
#define PS_ON_PIN 9
|
||||
#define KILL_PIN -1
|
||||
|
||||
#define HEATER_0_PIN 13
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define TEMP_0_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define TEMP_1_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define HEATER_BED_PIN 4
|
||||
#define TEMP_BED_PIN 10
|
||||
|
||||
#endif /* 99 */
|
||||
|
||||
/****************************************************************************************
|
||||
* Arduino pin assignment
|
||||
*
|
||||
|
||||
Loading…
Reference in New Issue
Block a user