3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-11-26 13:25:54 +00:00
Code Issues Releases Wiki Activity

Chitu V5 with extra GPIO init (#18299)

Browse Source 
Co-authored-by: Scott Lahteine <github@thinkyhead.com>
This commit is contained in:
Victor 2020-06-15 22:00:44 -03:00 committed by GitHub
parent 636813a83a
commit 8358f3eadb
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
3 changed files with 42 additions and 28 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

2
Marlin/src/pins/pins.h
View File

@ -541,7 +541,7 @@
#elif MB(CCROBOT_MEEB_3DP)
#include "stm32f1/pins_CCROBOT_MEEB_3DP.h" // STM32F1 env:STM32F103RC_meeb
#elif MB(CHITU3D_V5)
#include "stm32f1/pins_CHITU3D_V5.h" // STM32F1 env:chitu_f103
#include "stm32f1/pins_CHITU3D_V5.h" // STM32F1 env:chitu_f103 env:chitu_v5_gpio_init
#elif MB(CHITU3D_V6)
#include "stm32f1/pins_CHITU3D_V6.h" // STM32F1 env:chitu_f103

59
buildroot/share/PlatformIO/variants/CHITU_F103/wirish/boards_setup.cpp
View File

@ -49,17 +49,17 @@
// currently officially supports).
#ifndef BOARD_RCC_PLLMUL
#if !USE_HSI_CLOCK
#if F_CPU==128000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_16
#elif F_CPU==72000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_9
#elif F_CPU==48000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_6
#elif F_CPU==16000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_2
#endif
#if F_CPU==128000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_16
#elif F_CPU==72000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_9
#elif F_CPU==48000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_6
#elif F_CPU==16000000
#define BOARD_RCC_PLLMUL RCC_PLLMUL_2
#endif
#else
#define BOARD_RCC_PLLMUL RCC_PLLMUL_16
#define BOARD_RCC_PLLMUL RCC_PLLMUL_16
#endif
#endif
@ -83,33 +83,39 @@ namespace wirish {
rcc_set_prescaler(RCC_PRESCALER_AHB, RCC_AHB_SYSCLK_DIV_1);
rcc_set_prescaler(RCC_PRESCALER_APB1, RCC_APB1_HCLK_DIV_2);
rcc_set_prescaler(RCC_PRESCALER_APB2, RCC_APB2_HCLK_DIV_1);
rcc_clk_disable(RCC_USB);
#if F_CPU == 72000000
rcc_set_prescaler(RCC_PRESCALER_USB, RCC_USB_SYSCLK_DIV_1_5);
#elif F_CPU == 48000000
rcc_set_prescaler(RCC_PRESCALER_USB, RCC_USB_SYSCLK_DIV_1);
#endif
rcc_clk_disable(RCC_USB);
#if F_CPU == 72000000
rcc_set_prescaler(RCC_PRESCALER_USB, RCC_USB_SYSCLK_DIV_1_5);
#elif F_CPU == 48000000
rcc_set_prescaler(RCC_PRESCALER_USB, RCC_USB_SYSCLK_DIV_1);
#endif
}
__weak void board_setup_gpio(void) {
/**
* PA14 is a pull up pin. But, some V5 boards it start with LOW state! And just behave properly when the Z- PROBE is actived at least once.
* So, if the sensor isnt actived, the PA14 pin will be forever in LOW state, telling Marlin the probe IS ALWAYS ACTIVE, that isnt the case!
* Chitu original firmware seems to start with every pullup PIN with HIGH to workaround this.
* So we are doing the same here.
* This hack only works if applied *before* the GPIO Init, it's the reason I did it here.
*/
#ifdef CHITU_V5_Z_MIN_BUGFIX
GPIOA->regs->BSRR = (1U << PA14);
#endif
gpio_init_all();
}
__weak void board_setup_usb(void) {
#ifdef SERIAL_USB
#ifdef GENERIC_BOOTLOADER
//Reset the USB interface on generic boards - developed by Victor PV
gpio_set_mode(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit, GPIO_OUTPUT_PP);
gpio_write_bit(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit,0);
// Reset the USB interface on generic boards - developed by Victor PV
gpio_set_mode(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit, GPIO_OUTPUT_PP);
gpio_write_bit(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit,0);
for(volatile unsigned int i=0;i<512;i++);// Only small delay seems to be needed, and USB pins will get configured in Serial.begin
gpio_set_mode(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit, GPIO_INPUT_FLOATING);
for (volatile unsigned int i = 0; i < 512; i++); // Only small delay seems to be needed, and USB pins will get configured in Serial.begin
gpio_set_mode(PIN_MAP[PA12].gpio_device, PIN_MAP[PA12].gpio_bit, GPIO_INPUT_FLOATING);
#endif
Serial.begin();// Roger Clark. Changed SerialUSB to Serial for Arduino sketch compatibility
Serial.begin(); // Roger Clark. Changed SerialUSB to Serial for Arduino sketch compatibility
#endif
}
@ -118,6 +124,5 @@ namespace wirish {
// interrupts work out of the box.
afio_init();
}
}
}

9
platformio.ini
View File

@ -664,6 +664,15 @@ build_flags = ${common_stm32f1.build_flags}
build_unflags = ${common_stm32f1.build_unflags}
-DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG= -DERROR_LED_PORT=GPIOE -DERROR_LED_PIN=6
#
# Some Chitu V5 boards have a problem with GPIO init.
# Use this target if G28 or G29 are always failing.
#
[env:chitu_v5_gpio_init]
platform = ${common_stm32f1.platform}
extends = env:chitu_f103
build_flags = ${env:chitu_f103.build_flags} -DCHITU_V5_Z_MIN_BUGFIX
#
# STM32F401VE
# 'STEVAL-3DP001V1' STM32F401VE board - https://www.st.com/en/evaluation-tools/steval-3dp001v1.html