diff --git a/Marlin/src/feature/pause.cpp b/Marlin/src/feature/pause.cpp
index 58e0c3df0de..2bd30338085 100644
--- a/Marlin/src/feature/pause.cpp
+++ b/Marlin/src/feature/pause.cpp
@@ -406,6 +406,15 @@ bool pause_print(const_float_t retract, const xyz_pos_t &park_point, const bool
// Save current position
resume_position = current_position;
+ // Will the nozzle be parking?
+ const bool do_park = !axes_should_home();
+
+ #if ENABLED(POWER_LOSS_RECOVERY)
+ // Save PLR info in case the power goes out while parked
+ const float park_raise = do_park ? nozzle.park_mode_0_height(park_point.z) - current_position.z : POWER_LOSS_ZRAISE;
+ if (was_sd_printing && recovery.enabled) recovery.save(true, park_raise, do_park);
+ #endif
+
// Wait for buffered blocks to complete
planner.synchronize();
@@ -419,9 +428,8 @@ bool pause_print(const_float_t retract, const xyz_pos_t &park_point, const bool
unscaled_e_move(retract, PAUSE_PARK_RETRACT_FEEDRATE);
}
- // Park the nozzle by doing a Minimum Z Raise followed by an XY Move
- if (!axes_should_home())
- nozzle.park(0, park_point);
+ // If axes don't need to home then the nozzle can park
+ if (do_park) nozzle.park(0, park_point); // Park the nozzle by doing a Minimum Z Raise followed by an XY Move
#if ENABLED(DUAL_X_CARRIAGE)
const int8_t saved_ext = active_extruder;
@@ -429,7 +437,8 @@ bool pause_print(const_float_t retract, const xyz_pos_t &park_point, const bool
set_duplication_enabled(false, DXC_ext);
#endif
- if (unload_length) // Unload the filament
+ // Unload the filament, if specified
+ if (unload_length)
unload_filament(unload_length, show_lcd, PAUSE_MODE_CHANGE_FILAMENT);
#if ENABLED(DUAL_X_CARRIAGE)
diff --git a/Marlin/src/feature/powerloss.cpp b/Marlin/src/feature/powerloss.cpp
index 9d6e0b42f5d..552f1d90093 100644
--- a/Marlin/src/feature/powerloss.cpp
+++ b/Marlin/src/feature/powerloss.cpp
@@ -144,7 +144,7 @@ void PrintJobRecovery::prepare() {
/**
* Save the current machine state to the power-loss recovery file
*/
-void PrintJobRecovery::save(const bool force/*=false*/, const float zraise/*=0*/) {
+void PrintJobRecovery::save(const bool force/*=false*/, const float zraise/*=POWER_LOSS_ZRAISE*/, const bool raised/*=false*/) {
// We don't check IS_SD_PRINTING here so a save may occur during a pause
@@ -181,14 +181,12 @@ void PrintJobRecovery::save(const bool force/*=false*/, const float zraise/*=0*/
info.current_position = current_position;
info.feedrate = uint16_t(MMS_TO_MMM(feedrate_mm_s));
info.zraise = zraise;
+ info.flag.raised = raised; // Was Z raised before power-off?
TERN_(GCODE_REPEAT_MARKERS, info.stored_repeat = repeat);
TERN_(HAS_HOME_OFFSET, info.home_offset = home_offset);
TERN_(HAS_POSITION_SHIFT, info.position_shift = position_shift);
-
- #if HAS_MULTI_EXTRUDER
- info.active_extruder = active_extruder;
- #endif
+ TERN_(HAS_MULTI_EXTRUDER, info.active_extruder = active_extruder);
#if DISABLED(NO_VOLUMETRICS)
info.flag.volumetric_enabled = parser.volumetric_enabled;
@@ -289,8 +287,9 @@ void PrintJobRecovery::save(const bool force/*=false*/, const float zraise/*=0*/
constexpr float zraise = 0;
#endif
- // Save, including the limited Z raise
- if (IS_SD_PRINTING()) save(true, zraise);
+ // Save the current position, distance that Z was (or should be) raised,
+ // and a flag whether the raise was already done here.
+ if (IS_SD_PRINTING()) save(true, zraise, ENABLED(BACKUP_POWER_SUPPLY));
// Disable all heaters to reduce power loss
thermalManager.disable_all_heaters();
@@ -350,10 +349,10 @@ void PrintJobRecovery::resume() {
}
#endif
- // Restore all hotend temperatures
+ // Heat hotend enough to soften material
#if HAS_HOTEND
HOTEND_LOOP() {
- const celsius_t et = info.target_temperature[e];
+ const celsius_t et = _MAX(info.target_temperature[e], 180);
if (et) {
#if HAS_MULTI_HOTEND
sprintf_P(cmd, PSTR("T%iS"), e);
@@ -365,37 +364,59 @@ void PrintJobRecovery::resume() {
}
#endif
+ // Interpret the saved Z according to flags
+ const float z_print = info.current_position.z,
+ z_raised = z_print + info.zraise;
+
//
// Home the axes that can safely be homed, and
// establish the current position as best we can.
//
+
+ gcode.process_subcommands_now_P(PSTR("G92.9E0")); // Reset E to 0
+
#if Z_HOME_DIR > 0
- // If Z homing goes to max...
+ float z_now = z_raised;
+
+ // If Z homing goes to max then just move back to the "raised" position
gcode.process_subcommands_now_P(PSTR(
- "G92.9 E0\n" // Reset E to 0
- "G28R0" // Home all axes (no raise)
- ));
+ "G28R0\n" // Home all axes (no raise)
+ "G1Z%sF1200" // Move Z down to (raised) height
+ ),
+ dtostrf(z_now, 1, 3, str_1)
+ );
#else
- // If a Z raise occurred at outage restore Z, otherwise raise Z now
- sprintf_P(cmd, PSTR("G92.9 E0 " TERN(BACKUP_POWER_SUPPLY, "Z%s", "Z0\nG1Z%s")), dtostrf(info.zraise, 1, 3, str_1));
- gcode.process_subcommands_now(cmd);
+ #if ENABLED(POWER_LOSS_RECOVER_ZHOME) && defined(POWER_LOSS_ZHOME_POS)
+ #define HOMING_Z_DOWN 1
+ #else
+ #define HOME_XY_ONLY 1
+ #endif
- // Home safely with no Z raise
- gcode.process_subcommands_now_P(PSTR(
- "G28R0" // No raise during G28
- #if IS_CARTESIAN && (DISABLED(POWER_LOSS_RECOVER_ZHOME) || defined(POWER_LOSS_ZHOME_POS))
- "XY" // Don't home Z on Cartesian unless overridden
- #endif
- ));
+ float z_now = info.flag.raised ? z_raised : z_print;
+
+ // Reset E to 0 and set Z to the real position
+ #if HOME_XY_ONLY
+ sprintf_P(cmd, PSTR("G92.9Z%s"), dtostrf(z_now, 1, 3, str_1));
+ gcode.process_subcommands_now(cmd);
+ #endif
+
+ // Does Z need to be raised now? It should be raised before homing XY.
+ if (z_raised > z_now) {
+ z_now = z_raised;
+ sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_now, 1, 3, str_1));
+ gcode.process_subcommands_now(cmd);
+ }
+
+ // Home XY with no Z raise, and also home Z here if Z isn't homing down below.
+ gcode.process_subcommands_now_P(PSTR("G28R0" TERN_(HOME_XY_ONLY, "XY"))); // No raise during G28
#endif
- #if ENABLED(POWER_LOSS_RECOVER_ZHOME) && defined(POWER_LOSS_ZHOME_POS)
- // Move to a safe XY position where Z can home while avoiding the print.
- // If Z_SAFE_HOMING is enabled, its position must also be outside the print area!
+ #if HOMING_Z_DOWN
+ // Move to a safe XY position and home Z while avoiding the print.
constexpr xy_pos_t p = POWER_LOSS_ZHOME_POS;
sprintf_P(cmd, PSTR("G1X%sY%sF1000\nG28Z"), dtostrf(p.x, 1, 3, str_1), dtostrf(p.y, 1, 3, str_2));
gcode.process_subcommands_now(cmd);
@@ -404,9 +425,24 @@ void PrintJobRecovery::resume() {
// Mark all axes as having been homed (no effect on current_position)
set_all_homed();
+ #if HAS_LEVELING
+ // Restore Z fade and possibly re-enable bed leveling compensation.
+ // Leveling may already be enabled due to the ENABLE_LEVELING_AFTER_G28 option.
+ // TODO: Add a G28 parameter to leave leveling disabled.
+ sprintf_P(cmd, PSTR("M420S%cZ%s"), '0' + (char)info.flag.leveling, dtostrf(info.fade, 1, 1, str_1));
+ gcode.process_subcommands_now(cmd);
+
+ #if HOME_XY_ONLY
+ // The physical Z was adjusted at power-off so undo the M420S1 correction to Z with G92.9.
+ sprintf_P(cmd, PSTR("G92.9Z%s"), dtostrf(z_now, 1, 1, str_1));
+ gcode.process_subcommands_now(cmd);
+ #endif
+ #endif
+
#if ENABLED(POWER_LOSS_RECOVER_ZHOME)
- // Z was homed. Now move Z back up to the saved Z height, plus the POWER_LOSS_ZRAISE.
- sprintf_P(cmd, PSTR("G1Z%sF500"), dtostrf(info.current_position.z + POWER_LOSS_ZRAISE, 1, 3, str_1));
+ // Z was homed down to the bed, so move up to the raised height.
+ z_now = z_raised;
+ sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_now, 1, 3, str_1));
gcode.process_subcommands_now(cmd);
#endif
@@ -429,8 +465,23 @@ void PrintJobRecovery::resume() {
#endif
#endif
- // Select the previously active tool (with no_move)
- #if HAS_MULTI_EXTRUDER
+ // Restore all hotend temperatures
+ #if HAS_HOTEND
+ HOTEND_LOOP() {
+ const celsius_t et = info.target_temperature[e];
+ if (et) {
+ #if HAS_MULTI_HOTEND
+ sprintf_P(cmd, PSTR("T%iS"), e);
+ gcode.process_subcommands_now(cmd);
+ #endif
+ sprintf_P(cmd, PSTR("M109S%i"), et);
+ gcode.process_subcommands_now(cmd);
+ }
+ }
+ #endif
+
+ // Restore the previously active tool (with no_move)
+ #if HAS_MULTI_EXTRUDER || HAS_MULTI_HOTEND
sprintf_P(cmd, PSTR("T%i S"), info.active_extruder);
gcode.process_subcommands_now(cmd);
#endif
@@ -457,15 +508,6 @@ void PrintJobRecovery::resume() {
fwretract.current_hop = info.retract_hop;
#endif
- #if HAS_LEVELING
- // Restore leveling state before 'G92 Z' to ensure
- // the Z stepper count corresponds to the native Z.
- if (info.fade || info.flag.leveling) {
- sprintf_P(cmd, PSTR("M420S%cZ%s"), '0' + (char)info.flag.leveling, dtostrf(info.fade, 1, 1, str_1));
- gcode.process_subcommands_now(cmd);
- }
- #endif
-
#if ENABLED(GRADIENT_MIX)
memcpy(&mixer.gradient, &info.gradient, sizeof(info.gradient));
#endif
@@ -492,14 +534,8 @@ void PrintJobRecovery::resume() {
);
gcode.process_subcommands_now(cmd);
- // Move back to the saved Z
- dtostrf(info.current_position.z, 1, 3, str_1);
- #if Z_HOME_DIR > 0 || ENABLED(POWER_LOSS_RECOVER_ZHOME)
- sprintf_P(cmd, PSTR("G1 Z%s F500"), str_1);
- #else
- gcode.process_subcommands_now_P(PSTR("G1 Z0 F200"));
- sprintf_P(cmd, PSTR("G92.9 Z%s"), str_1);
- #endif
+ // Move back down to the saved Z for printing
+ sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_print, 1, 3, str_1));
gcode.process_subcommands_now(cmd);
// Restore the feedrate
@@ -552,7 +588,15 @@ void PrintJobRecovery::resume() {
}
DEBUG_EOL();
- DEBUG_ECHOLNPAIR("zraise: ", info.zraise);
+ DEBUG_ECHOLNPAIR("feedrate: ", info.feedrate);
+
+ DEBUG_ECHOLNPAIR("zraise: ", info.zraise, " ", info.flag.raised ? "(before)" : "");
+
+ #if ENABLED(GCODE_REPEAT_MARKERS)
+ DEBUG_ECHOLNPAIR("repeat index: ", info.stored_repeat.index);
+ LOOP_L_N(i, info.stored_repeat.index)
+ DEBUG_ECHOLNPAIR("..... sdpos: ", info.stored_repeat.marker.sdpos, " count: ", info.stored_repeat.marker.counter);
+ #endif
#if HAS_HOME_OFFSET
DEBUG_ECHOPGM("home_offset: ");
@@ -572,12 +616,16 @@ void PrintJobRecovery::resume() {
DEBUG_EOL();
#endif
- DEBUG_ECHOLNPAIR("feedrate: ", info.feedrate);
-
#if HAS_MULTI_EXTRUDER
DEBUG_ECHOLNPAIR("active_extruder: ", info.active_extruder);
#endif
+ #if DISABLED(NO_VOLUMETRICS)
+ DEBUG_ECHOPGM("filament_size:");
+ LOOP_L_N(i, EXTRUDERS) DEBUG_ECHOLNPAIR(" ", info.filament_size[i]);
+ DEBUG_EOL();
+ #endif
+
#if HAS_HOTEND
DEBUG_ECHOPGM("target_temperature: ");
HOTEND_LOOP() {
@@ -601,8 +649,9 @@ void PrintJobRecovery::resume() {
#endif
#if HAS_LEVELING
- DEBUG_ECHOLNPAIR("leveling: ", info.flag.leveling, " fade: ", info.fade);
+ DEBUG_ECHOLNPAIR("leveling: ", info.flag.leveling ? "ON" : "OFF", " fade: ", info.fade);
#endif
+
#if ENABLED(FWRETRACT)
DEBUG_ECHOPGM("retract: ");
for (int8_t e = 0; e < EXTRUDERS; e++) {
@@ -612,11 +661,28 @@ void PrintJobRecovery::resume() {
DEBUG_EOL();
DEBUG_ECHOLNPAIR("retract_hop: ", info.retract_hop);
#endif
+
+ // Mixing extruder and gradient
+ #if BOTH(MIXING_EXTRUDER, GRADIENT_MIX)
+ DEBUG_ECHOLNPAIR("gradient: ", info.gradient.enabled ? "ON" : "OFF");
+ #endif
+
DEBUG_ECHOLNPAIR("sd_filename: ", info.sd_filename);
DEBUG_ECHOLNPAIR("sdpos: ", info.sdpos);
DEBUG_ECHOLNPAIR("print_job_elapsed: ", info.print_job_elapsed);
- DEBUG_ECHOLNPAIR("dryrun: ", AS_DIGIT(info.flag.dryrun));
- DEBUG_ECHOLNPAIR("allow_cold_extrusion: ", info.flag.allow_cold_extrusion);
+
+ DEBUG_ECHOPGM("axis_relative:");
+ if (TEST(info.axis_relative, REL_X)) DEBUG_ECHOPGM(" REL_X");
+ if (TEST(info.axis_relative, REL_Y)) DEBUG_ECHOPGM(" REL_Y");
+ if (TEST(info.axis_relative, REL_Z)) DEBUG_ECHOPGM(" REL_Z");
+ if (TEST(info.axis_relative, REL_E)) DEBUG_ECHOPGM(" REL_E");
+ if (TEST(info.axis_relative, E_MODE_ABS)) DEBUG_ECHOPGM(" E_MODE_ABS");
+ if (TEST(info.axis_relative, E_MODE_REL)) DEBUG_ECHOPGM(" E_MODE_REL");
+ DEBUG_EOL();
+
+ DEBUG_ECHOLNPAIR("flag.dryrun: ", AS_DIGIT(info.flag.dryrun));
+ DEBUG_ECHOLNPAIR("flag.allow_cold_extrusion: ", AS_DIGIT(info.flag.allow_cold_extrusion));
+ DEBUG_ECHOLNPAIR("flag.volumetric_enabled: ", AS_DIGIT(info.flag.volumetric_enabled));
}
else
DEBUG_ECHOLNPGM("INVALID DATA");
diff --git a/Marlin/src/feature/powerloss.h b/Marlin/src/feature/powerloss.h
index df3ae222a26..0fa9172fcf0 100644
--- a/Marlin/src/feature/powerloss.h
+++ b/Marlin/src/feature/powerloss.h
@@ -117,6 +117,7 @@ typedef struct {
// Misc. Marlin flags
struct {
+ bool raised:1; // Raised before saved
bool dryrun:1; // M111 S8
bool allow_cold_extrusion:1; // M302 P1
#if ENABLED(HAS_LEVELING)
@@ -182,7 +183,7 @@ class PrintJobRecovery {
static inline void cancel() { purge(); IF_DISABLED(NO_SD_AUTOSTART, card.autofile_begin()); }
static void load();
- static void save(const bool force=ENABLED(SAVE_EACH_CMD_MODE), const float zraise=0);
+ static void save(const bool force=ENABLED(SAVE_EACH_CMD_MODE), const float zraise=POWER_LOSS_ZRAISE, const bool raised=false);
#if PIN_EXISTS(POWER_LOSS)
static inline void outage() {
diff --git a/Marlin/src/gcode/feature/pause/M125.cpp b/Marlin/src/gcode/feature/pause/M125.cpp
index 351ef01f347..2eb4ceea417 100644
--- a/Marlin/src/gcode/feature/pause/M125.cpp
+++ b/Marlin/src/gcode/feature/pause/M125.cpp
@@ -78,8 +78,6 @@ void GcodeSuite::M125() {
// If possible, show an LCD prompt with the 'P' flag
const bool show_lcd = TERN0(HAS_LCD_MENU, parser.boolval('P'));
- TERN_(POWER_LOSS_RECOVERY, if (recovery.enabled) recovery.save(true));
-
if (pause_print(retract, park_point, show_lcd, 0)) {
if (ENABLED(EXTENSIBLE_UI) || BOTH(EMERGENCY_PARSER, HOST_PROMPT_SUPPORT) || !sd_printing || show_lcd) {
wait_for_confirmation(false, 0);
diff --git a/Marlin/src/gcode/sd/M24_M25.cpp b/Marlin/src/gcode/sd/M24_M25.cpp
index f46a964af07..4cb040feb35 100644
--- a/Marlin/src/gcode/sd/M24_M25.cpp
+++ b/Marlin/src/gcode/sd/M24_M25.cpp
@@ -105,7 +105,7 @@ void GcodeSuite::M25() {
if (IS_SD_PRINTING()) card.pauseSDPrint();
#endif
- #if ENABLED(POWER_LOSS_RECOVERY)
+ #if ENABLED(POWER_LOSS_RECOVERY) && DISABLED(DGUS_LCD_UI_MKS)
if (recovery.enabled) recovery.save(true);
#endif
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index bbd646a30d9..c9aebe89ad0 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -2903,6 +2903,8 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
#error "POWER_LOSS_RECOVER_ZHOME cannot be used with Z_SAFE_HOMING."
#elif BOTH(POWER_LOSS_PULLUP, POWER_LOSS_PULLDOWN)
#error "You can't enable POWER_LOSS_PULLUP and POWER_LOSS_PULLDOWN at the same time."
+ #elif ENABLED(POWER_LOSS_RECOVER_ZHOME) && Z_HOME_DIR > 0
+ #error "POWER_LOSS_RECOVER_ZHOME is not needed on a machine that homes to ZMAX."
#elif BOTH(IS_CARTESIAN, POWER_LOSS_RECOVER_ZHOME) && Z_HOME_DIR < 0 && !defined(POWER_LOSS_ZHOME_POS)
#error "POWER_LOSS_RECOVER_ZHOME requires POWER_LOSS_ZHOME_POS for a Cartesian that homes to ZMIN."
#endif
diff --git a/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp b/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp
index 7d98b64991e..525b781599c 100644
--- a/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp
+++ b/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp
@@ -39,6 +39,10 @@
#include "../../../../module/stepper/trinamic.h"
#endif
+#if ENABLED(POWER_LOSS_RECOVERY)
+ #include "../../../../../feature/powerloss.h"
+#endif
+
#if ENABLED(DGUS_UI_MOVE_DIS_OPTION)
uint16_t distanceToMove = 10;
#endif
@@ -78,8 +82,13 @@ constexpr feedRate_t park_speed_xy = TERN(NOZZLE_PARK_FEATURE, NOZZLE_PARK_XY_FE
void MKS_pause_print_move() {
queue.exhaust();
position_before_pause = current_position;
+
+ // Save the current position, the raise amount, and 'already raised'
+ TERN_(POWER_LOSS_RECOVERY, if (recovery.enabled) recovery.save(true, mks_park_pos.z, true));
+
destination.z = _MIN(current_position.z + mks_park_pos.z, Z_MAX_POS);
prepare_internal_move_to_destination(park_speed_z);
+
destination.set(X_MIN_POS + mks_park_pos.x, Y_MIN_POS + mks_park_pos.y);
prepare_internal_move_to_destination(park_speed_xy);
}
@@ -89,6 +98,7 @@ void MKS_resume_print_move() {
prepare_internal_move_to_destination(park_speed_xy);
destination.z = position_before_pause.z;
prepare_internal_move_to_destination(park_speed_z);
+ TERN_(POWER_LOSS_RECOVERY, if (recovery.enabled) recovery.save(true));
}
float z_offset_add = 0;
diff --git a/buildroot/tests/rambo b/buildroot/tests/rambo
index 95260e58b47..87772a988bb 100755
--- a/buildroot/tests/rambo
+++ b/buildroot/tests/rambo
@@ -14,9 +14,9 @@ opt_set MOTHERBOARD BOARD_RAMBO \
EXTRUDERS 2 TEMP_SENSOR_0 -2 TEMP_SENSOR_1 1 TEMP_SENSOR_BED 2 \
TEMP_SENSOR_PROBE 1 TEMP_PROBE_PIN 12 \
TEMP_SENSOR_CHAMBER 3 TEMP_CHAMBER_PIN 3 HEATER_CHAMBER_PIN 45 \
- Z_HOME_DIR 1 GRID_MAX_POINTS_X 16 \
+ GRID_MAX_POINTS_X 16 \
FANMUX0_PIN 53
-opt_disable USE_ZMIN_PLUG Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG
+opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG
opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
FIX_MOUNTED_PROBE CODEPENDENT_XY_HOMING PIDTEMPBED PROBE_TEMP_COMPENSATION \
PREHEAT_BEFORE_PROBING PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \
@@ -32,7 +32,7 @@ opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_P
SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE \
BACKLASH_COMPENSATION BACKLASH_GCODE BAUD_RATE_GCODE BEZIER_CURVE_SUPPORT \
FWRETRACT ARC_P_CIRCLES CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS \
- PSU_CONTROL AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE POWER_LOSS_RECOVER_ZHOME \
+ PSU_CONTROL AUTO_POWER_CONTROL POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE POWER_LOSS_RECOVER_ZHOME POWER_LOSS_ZHOME_POS \
SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL
opt_add DEBUG_POWER_LOSS_RECOVERY
@@ -43,7 +43,7 @@ exec_test $1 $2 "RAMBO | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear |
#
restore_configs
opt_set MOTHERBOARD BOARD_RAMBO \
- EXTRUDERS 0 TEMP_SENSOR_0 999 DUMMY_THERMISTOR_999_VALUE 170 \
+ EXTRUDERS 0 TEMP_SENSOR_0 999 DUMMY_THERMISTOR_999_VALUE 170 Z_HOME_DIR 1 \
DIGIPOT_MOTOR_CURRENT '{ 120, 120, 120, 120, 120 }' \
LEVEL_CORNERS_LEVELING_ORDER '{ LF, RF }'
opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \