diff --git a/Marlin/src/feature/powerloss.cpp b/Marlin/src/feature/powerloss.cpp
index 2825f4d4f2..1037f823f6 100644
--- a/Marlin/src/feature/powerloss.cpp
+++ b/Marlin/src/feature/powerloss.cpp
@@ -78,6 +78,14 @@ PrintJobRecovery recovery;
   #define POWER_LOSS_RETRACT_LEN 0
 #endif
 
+// Allow power-loss recovery to be aborted
+#define PLR_CAN_ABORT
+#if ENABLED(PLR_CAN_ABORT)
+  #define PROCESS_SUBCOMMANDS_NOW(cmd) do { if (card.flag.abort_sd_printing) return; gcode.process_subcommands_now(cmd); }while(0)
+#else
+  #define PROCESS_SUBCOMMANDS_NOW(cmd) gcode.process_subcommands_now(cmd)
+#endif
+
 /**
  * Clear the recovery info
  */
@@ -352,12 +360,23 @@ void PrintJobRecovery::resume() {
   // Apply the dry-run flag if enabled
   if (info.flag.dryrun) marlin_debug_flags |= MARLIN_DEBUG_DRYRUN;
 
+  #if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
+    struct OnExit {
+      uint8_t old_flags;
+      OnExit() {
+        old_flags = marlin_debug_flags;
+        marlin_debug_flags |= MARLIN_DEBUG_ECHO;
+      }
+      ~OnExit() { marlin_debug_flags = old_flags; }
+    } on_exit;
+  #endif
+
   // Restore cold extrusion permission
   TERN_(PREVENT_COLD_EXTRUSION, thermalManager.allow_cold_extrude = info.flag.allow_cold_extrusion);
 
   #if HAS_LEVELING
     // Make sure leveling is off before any G92 and G28
-    gcode.process_subcommands_now(F("M420 S0 Z0"));
+    PROCESS_SUBCOMMANDS_NOW(F("M420S0"));
   #endif
 
   #if HAS_HEATED_BED
@@ -365,7 +384,7 @@ void PrintJobRecovery::resume() {
     if (bt) {
       // Restore the bed temperature
       sprintf_P(cmd, PSTR("M190S%i"), bt);
-      gcode.process_subcommands_now(cmd);
+      PROCESS_SUBCOMMANDS_NOW(cmd);
     }
   #endif
 
@@ -376,10 +395,10 @@ void PrintJobRecovery::resume() {
       if (et) {
         #if HAS_MULTI_HOTEND
           sprintf_P(cmd, PSTR("T%iS"), e);
-          gcode.process_subcommands_now(cmd);
+          PROCESS_SUBCOMMANDS_NOW(cmd);
         #endif
         sprintf_P(cmd, PSTR("M109S%i"), et);
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
     }
   #endif
@@ -393,7 +412,7 @@ void PrintJobRecovery::resume() {
   // establish the current position as best we can.
   //
 
-  gcode.process_subcommands_now(F("G92.9E0")); // Reset E to 0
+  PROCESS_SUBCOMMANDS_NOW(F("G92.9E0")); // Reset E to 0
 
   #if Z_HOME_TO_MAX
 
@@ -404,7 +423,7 @@ void PrintJobRecovery::resume() {
             "G28R0\n"     // Home all axes (no raise)
             "G1Z%sF1200"  // Move Z down to (raised) height
           ), dtostrf(z_now, 1, 3, str_1));
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
 
   #elif DISABLED(BELTPRINTER)
 
@@ -417,18 +436,18 @@ void PrintJobRecovery::resume() {
     #if !HOMING_Z_DOWN
       // Set Z to the real position
       sprintf_P(cmd, PSTR("G92.9Z%s"), dtostrf(z_now, 1, 3, str_1));
-      gcode.process_subcommands_now(cmd);
+      PROCESS_SUBCOMMANDS_NOW(cmd);
     #endif
 
     // Does Z need to be raised now? It should be raised before homing XY.
     if (z_raised > z_now) {
       z_now = z_raised;
       sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_now, 1, 3, str_1));
-      gcode.process_subcommands_now(cmd);
+      PROCESS_SUBCOMMANDS_NOW(cmd);
     }
 
     // Home XY with no Z raise
-    gcode.process_subcommands_now(F("G28R0XY")); // No raise during G28
+    PROCESS_SUBCOMMANDS_NOW(F("G28R0XY")); // No raise during G28
 
   #endif
 
@@ -436,7 +455,7 @@ void PrintJobRecovery::resume() {
     // Move to a safe XY position and home Z while avoiding the print.
     const xy_pos_t p = xy_pos_t(POWER_LOSS_ZHOME_POS) TERN_(HOMING_Z_WITH_PROBE, - probe.offset_xy);
     sprintf_P(cmd, PSTR("G1X%sY%sF1000\nG28HZ"), dtostrf(p.x, 1, 3, str_1), dtostrf(p.y, 1, 3, str_2));
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
   #endif
 
   // Mark all axes as having been homed (no effect on current_position)
@@ -447,12 +466,12 @@ void PrintJobRecovery::resume() {
     // Leveling may already be enabled due to the ENABLE_LEVELING_AFTER_G28 option.
     // TODO: Add a G28 parameter to leave leveling disabled.
     sprintf_P(cmd, PSTR("M420S%cZ%s"), '0' + (char)info.flag.leveling, dtostrf(info.fade, 1, 1, str_1));
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
 
     #if !HOMING_Z_DOWN
       // The physical Z was adjusted at power-off so undo the M420S1 correction to Z with G92.9.
       sprintf_P(cmd, PSTR("G92.9Z%s"), dtostrf(z_now, 1, 1, str_1));
-      gcode.process_subcommands_now(cmd);
+      PROCESS_SUBCOMMANDS_NOW(cmd);
     #endif
   #endif
 
@@ -460,7 +479,7 @@ void PrintJobRecovery::resume() {
     // Z was homed down to the bed, so move up to the raised height.
     z_now = z_raised;
     sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_now, 1, 3, str_1));
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
   #endif
 
   // Recover volumetric extrusion state
@@ -468,16 +487,16 @@ void PrintJobRecovery::resume() {
     #if HAS_MULTI_EXTRUDER
       EXTRUDER_LOOP() {
         sprintf_P(cmd, PSTR("M200T%iD%s"), e, dtostrf(info.filament_size[e], 1, 3, str_1));
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
       if (!info.flag.volumetric_enabled) {
         sprintf_P(cmd, PSTR("M200T%iD0"), info.active_extruder);
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
     #else
       if (info.flag.volumetric_enabled) {
         sprintf_P(cmd, PSTR("M200D%s"), dtostrf(info.filament_size[0], 1, 3, str_1));
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
     #endif
   #endif
@@ -489,10 +508,10 @@ void PrintJobRecovery::resume() {
       if (et) {
         #if HAS_MULTI_HOTEND
           sprintf_P(cmd, PSTR("T%iS"), e);
-          gcode.process_subcommands_now(cmd);
+          PROCESS_SUBCOMMANDS_NOW(cmd);
         #endif
         sprintf_P(cmd, PSTR("M109S%i"), et);
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
     }
   #endif
@@ -500,7 +519,7 @@ void PrintJobRecovery::resume() {
   // Restore the previously active tool (with no_move)
   #if HAS_MULTI_EXTRUDER || HAS_MULTI_HOTEND
     sprintf_P(cmd, PSTR("T%i S"), info.active_extruder);
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
   #endif
 
   // Restore print cooling fan speeds
@@ -509,7 +528,7 @@ void PrintJobRecovery::resume() {
       const int f = info.fan_speed[i];
       if (f) {
         sprintf_P(cmd, PSTR("M106P%iS%i"), i, f);
-        gcode.process_subcommands_now(cmd);
+        PROCESS_SUBCOMMANDS_NOW(cmd);
       }
     }
   #endif
@@ -531,17 +550,17 @@ void PrintJobRecovery::resume() {
 
   // Un-retract if there was a retract at outage
   #if ENABLED(BACKUP_POWER_SUPPLY) && POWER_LOSS_RETRACT_LEN > 0
-    gcode.process_subcommands_now(F("G1F3000E" STRINGIFY(POWER_LOSS_RETRACT_LEN)));
+    PROCESS_SUBCOMMANDS_NOW(F("G1F3000E" STRINGIFY(POWER_LOSS_RETRACT_LEN)));
   #endif
 
   // Additional purge on resume if configured
   #if POWER_LOSS_PURGE_LEN
     sprintf_P(cmd, PSTR("G1F3000E%d"), (POWER_LOSS_PURGE_LEN) + (POWER_LOSS_RETRACT_LEN));
-    gcode.process_subcommands_now(cmd);
+    PROCESS_SUBCOMMANDS_NOW(cmd);
   #endif
 
   #if ENABLED(NOZZLE_CLEAN_FEATURE)
-    gcode.process_subcommands_now(F("G12"));
+    PROCESS_SUBCOMMANDS_NOW(F("G12"));
   #endif
 
   // Move back over to the saved XY
@@ -549,19 +568,19 @@ void PrintJobRecovery::resume() {
     dtostrf(info.current_position.x, 1, 3, str_1),
     dtostrf(info.current_position.y, 1, 3, str_2)
   );
-  gcode.process_subcommands_now(cmd);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
 
   // Move back down to the saved Z for printing
   sprintf_P(cmd, PSTR("G1Z%sF600"), dtostrf(z_print, 1, 3, str_1));
-  gcode.process_subcommands_now(cmd);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
 
   // Restore the feedrate
   sprintf_P(cmd, PSTR("G1F%d"), info.feedrate);
-  gcode.process_subcommands_now(cmd);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
 
   // Restore E position with G92.9
   sprintf_P(cmd, PSTR("G92.9E%s"), dtostrf(info.current_position.e, 1, 3, str_1));
-  gcode.process_subcommands_now(cmd);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
 
   TERN_(GCODE_REPEAT_MARKERS, repeat = info.stored_repeat);
   TERN_(HAS_HOME_OFFSET, home_offset = info.home_offset);
@@ -573,22 +592,14 @@ void PrintJobRecovery::resume() {
   // Relative axis modes
   gcode.axis_relative = info.axis_relative;
 
-  #if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
-    const uint8_t old_flags = marlin_debug_flags;
-    marlin_debug_flags |= MARLIN_DEBUG_ECHO;
-  #endif
-
   // Continue to apply PLR when a file is resumed!
   enable(true);
 
   // Resume the SD file from the last position
-  char *fn = info.sd_filename;
-  sprintf_P(cmd, M23_STR, fn);
-  gcode.process_subcommands_now(cmd);
+  sprintf_P(cmd, M23_STR, &info.sd_filename[0]);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
   sprintf_P(cmd, PSTR("M24S%ldT%ld"), resume_sdpos, info.print_job_elapsed);
-  gcode.process_subcommands_now(cmd);
-
-  TERN_(DEBUG_POWER_LOSS_RECOVERY, marlin_debug_flags = old_flags);
+  PROCESS_SUBCOMMANDS_NOW(cmd);
 }
 
 #if ENABLED(DEBUG_POWER_LOSS_RECOVERY)