mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-29 23:07:42 +00:00
Fix stepper pulse duration
This commit is contained in:
Scott Lahteine
parent
d3567592d7
commit
9d91ea4e3e
24
Marlin/HAL.h
24
Marlin/HAL.h
@ -95,21 +95,15 @@ inline uint8_t HAL_get_reset_source(void) { return MCUSR; }
|
||||
#define TEMP_TIMER_NUM 0
|
||||
#define PULSE_TIMER_NUM STEP_TIMER_NUM
|
||||
|
||||
#define TEMP_TIMER_FREQUENCY ((F_CPU) / 64.0 / 256.0)
|
||||
|
||||
#define STEPPER_TIMER_RATE HAL_TIMER_RATE
|
||||
#define HAL_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // Cannot be of type double
|
||||
#define STEPPER_TIMER_PRESCALE 8
|
||||
#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts
|
||||
#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // Cannot be of type double
|
||||
|
||||
#define TEMP_TIMER_PRESCALE 64
|
||||
#define TEMP_TIMER_FREQUENCY ((F_CPU) / float(TEMP_TIMER_PRESCALE) / 256.0)
|
||||
|
||||
#define TIMER_OCR_1 OCR1A
|
||||
#define TIMER_COUNTER_1 TCNT1
|
||||
|
||||
#define TIMER_OCR_0 OCR0A
|
||||
#define TIMER_COUNTER_0 TCNT0
|
||||
|
||||
#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE
|
||||
#define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer
|
||||
#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE
|
||||
#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US
|
||||
|
||||
#define ENABLE_STEPPER_DRIVER_INTERRUPT() SBI(TIMSK1, OCIE1A)
|
||||
#define DISABLE_STEPPER_DRIVER_INTERRUPT() CBI(TIMSK1, OCIE1A)
|
||||
@ -150,6 +144,12 @@ FORCE_INLINE void HAL_timer_start(const uint8_t timer_num, const uint32_t freque
|
||||
}
|
||||
}
|
||||
|
||||
#define TIMER_OCR_1 OCR1A
|
||||
#define TIMER_COUNTER_1 TCNT1
|
||||
|
||||
#define TIMER_OCR_0 OCR0A
|
||||
#define TIMER_COUNTER_0 TCNT0
|
||||
|
||||
#define _CAT(a, ...) a ## __VA_ARGS__
|
||||
#define HAL_timer_set_compare(timer, compare) (_CAT(TIMER_OCR_, timer) = compare)
|
||||
#define HAL_timer_restrain(timer, interval_ticks) NOLESS(_CAT(TIMER_OCR_, timer), _CAT(TIMER_COUNTER_, timer) + interval_ticks)
|
||||
|
||||
@ -1214,7 +1214,7 @@ void Stepper::isr() {
|
||||
* On AVR the ISR epilogue+prologue is estimated at 100 instructions - Give 8µs as margin
|
||||
* On ARM the ISR epilogue+prologue is estimated at 20 instructions - Give 1µs as margin
|
||||
*/
|
||||
min_ticks = HAL_timer_get_count(STEP_TIMER_NUM) + hal_timer_t((HAL_TICKS_PER_US) * 8);
|
||||
min_ticks = HAL_timer_get_count(STEP_TIMER_NUM) + hal_timer_t((STEPPER_TIMER_TICKS_PER_US) * 8);
|
||||
|
||||
/**
|
||||
* NB: If for some reason the stepper monopolizes the MPU, eventually the
|
||||
@ -1266,10 +1266,10 @@ void Stepper::stepper_pulse_phase_isr() {
|
||||
// Just update the value we will get at the end of the loop
|
||||
step_events_completed += events_to_do;
|
||||
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Get the timer count and estimate the end of the pulse
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE));
|
||||
#endif
|
||||
// Get the timer count and estimate the end of the pulse
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS);
|
||||
|
||||
const hal_timer_t added_step_ticks = ADDED_STEP_TICKS;
|
||||
|
||||
// Take multiple steps per interrupt (For high speed moves)
|
||||
do {
|
||||
@ -1342,10 +1342,11 @@ void Stepper::stepper_pulse_phase_isr() {
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
// Add to the value, the value needed for the pulse end and ensuring the maximum driver rate is enforced
|
||||
pulse_end += hal_timer_t(MIN_STEPPER_PULSE_CYCLES) - hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE));
|
||||
#endif
|
||||
|
||||
// Add the delay needed to ensure the maximum driver rate is enforced
|
||||
if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks);
|
||||
|
||||
// Pulse stop
|
||||
#if HAS_X_STEP
|
||||
PULSE_STOP(X);
|
||||
@ -1373,15 +1374,15 @@ void Stepper::stepper_pulse_phase_isr() {
|
||||
// Decrement the count of pending pulses to do
|
||||
--events_to_do;
|
||||
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// For minimum pulse time wait after stopping pulses also
|
||||
if (events_to_do) {
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
// For minimum pulse time wait after stopping pulses also
|
||||
if (events_to_do) {
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Add to the value, the time that the pulse must be active (to be used on the next loop)
|
||||
pulse_end += hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE));
|
||||
}
|
||||
#endif
|
||||
pulse_end += hal_timer_t(MIN_PULSE_TICKS);
|
||||
#endif
|
||||
}
|
||||
|
||||
} while (events_to_do);
|
||||
}
|
||||
@ -1760,13 +1761,15 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
||||
REV_E_DIR(active_extruder);
|
||||
#endif
|
||||
|
||||
// Get the timer count and estimate the end of the pulse
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS);
|
||||
|
||||
const hal_timer_t added_step_ticks = ADDED_STEP_TICKS;
|
||||
|
||||
// Step E stepper if we have steps
|
||||
while (LA_steps) {
|
||||
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE));
|
||||
#endif
|
||||
|
||||
// Set the STEP pulse ON
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
MIXING_STEPPERS_LOOP(j) {
|
||||
// Step mixing steppers (proportionally)
|
||||
@ -1778,15 +1781,18 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
||||
E_STEP_WRITE(active_extruder, !INVERT_E_STEP_PIN);
|
||||
#endif
|
||||
|
||||
// Enforce a minimum duration for STEP pulse ON
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
// Add to the value, the value needed for the pulse end and ensuring the maximum driver rate is enforced
|
||||
pulse_end += hal_timer_t(MIN_STEPPER_PULSE_CYCLES) - hal_timer_t((HAL_TICKS_PER_US) * (MINIMUM_STEPPER_PULSE));
|
||||
#endif
|
||||
|
||||
// Add the delay needed to ensure the maximum driver rate is enforced
|
||||
if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks);
|
||||
|
||||
LA_steps < 0 ? ++LA_steps : --LA_steps;
|
||||
|
||||
// Set the STEP pulse OFF
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
MIXING_STEPPERS_LOOP(j) {
|
||||
if (delta_error_m[j] >= 0) {
|
||||
@ -1798,12 +1804,15 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
||||
E_STEP_WRITE(active_extruder, INVERT_E_STEP_PIN);
|
||||
#endif
|
||||
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// For minimum pulse time wait before looping
|
||||
// Just wait for the requested pulse duration
|
||||
if (LA_steps) while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#endif
|
||||
|
||||
// For minimum pulse time wait before looping
|
||||
// Just wait for the requested pulse duration
|
||||
if (LA_steps) {
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Add to the value, the time that the pulse must be active (to be used on the next loop)
|
||||
pulse_end += hal_timer_t(MIN_PULSE_TICKS);
|
||||
#endif
|
||||
}
|
||||
} // LA_steps
|
||||
|
||||
return interval;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user