diff --git a/ArduinoAddons/Arduino_0.xx/Gen6/bootloaders/atmega644p/ATmegaBOOT.c b/ArduinoAddons/Arduino_0.xx/Gen6/bootloaders/atmega644p/ATmegaBOOT.c index 1711014459..3b56dfd224 100644 --- a/ArduinoAddons/Arduino_0.xx/Gen6/bootloaders/atmega644p/ATmegaBOOT.c +++ b/ArduinoAddons/Arduino_0.xx/Gen6/bootloaders/atmega644p/ATmegaBOOT.c @@ -168,7 +168,7 @@ int main(void) WDTCSR = 0; // Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot. - if (! (ch & _BV(EXTRF))) // if its a not an external reset... + if (! (ch & _BV(EXTRF))) // if it's a not an external reset... app_start(); // skip bootloader #endif diff --git a/ArduinoAddons/Arduino_0.xx/Sanguino/bootloaders/atmega644p/ATmegaBOOT.c b/ArduinoAddons/Arduino_0.xx/Sanguino/bootloaders/atmega644p/ATmegaBOOT.c index 1711014459..3b56dfd224 100644 --- a/ArduinoAddons/Arduino_0.xx/Sanguino/bootloaders/atmega644p/ATmegaBOOT.c +++ b/ArduinoAddons/Arduino_0.xx/Sanguino/bootloaders/atmega644p/ATmegaBOOT.c @@ -168,7 +168,7 @@ int main(void) WDTCSR = 0; // Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot. - if (! (ch & _BV(EXTRF))) // if its a not an external reset... + if (! (ch & _BV(EXTRF))) // if it's a not an external reset... app_start(); // skip bootloader #endif diff --git a/ArduinoAddons/Arduino_0.xx/libraries/LiquidCrystal/LiquidCrystal.cpp b/ArduinoAddons/Arduino_0.xx/libraries/LiquidCrystal/LiquidCrystal.cpp index 23713f47b9..c3362f6d8f 100644 --- a/ArduinoAddons/Arduino_0.xx/libraries/LiquidCrystal/LiquidCrystal.cpp +++ b/ArduinoAddons/Arduino_0.xx/libraries/LiquidCrystal/LiquidCrystal.cpp @@ -21,7 +21,7 @@ // S = 0; No shift // // Note, however, that resetting the Arduino doesn't reset the LCD, so we -// can't assume that its in that state when a sketch starts (and the +// can't assume that it's in that state when a sketch starts (and the // LiquidCrystal constructor is called). LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable, diff --git a/ArduinoAddons/Arduino_0.xx/libraries/U8glib/utility/chessengine.c b/ArduinoAddons/Arduino_0.xx/libraries/U8glib/utility/chessengine.c index f86bf0687e..4a8758c382 100644 --- a/ArduinoAddons/Arduino_0.xx/libraries/U8glib/utility/chessengine.c +++ b/ArduinoAddons/Arduino_0.xx/libraries/U8glib/utility/chessengine.c @@ -72,7 +72,7 @@ - Castling: Need to check for fields under attack --> done - - Check for WIN / LOOSE situation, perhaps call ce_Eval() once on the top-level board setup + - Check for WIN / LOSE situation, perhaps call ce_Eval() once on the top-level board setup just after the real move - cleanup cu_Move --> almost done diff --git a/ArduinoAddons/Arduino_1.x.x/libraries/LiquidCrystal/LiquidCrystal.cpp b/ArduinoAddons/Arduino_1.x.x/libraries/LiquidCrystal/LiquidCrystal.cpp index 0653487d70..61efca46e0 100644 --- a/ArduinoAddons/Arduino_1.x.x/libraries/LiquidCrystal/LiquidCrystal.cpp +++ b/ArduinoAddons/Arduino_1.x.x/libraries/LiquidCrystal/LiquidCrystal.cpp @@ -21,7 +21,7 @@ // S = 0; No shift // // Note, however, that resetting the Arduino doesn't reset the LCD, so we -// can't assume that its in that state when a sketch starts (and the +// can't assume that it's in that state when a sketch starts (and the // LiquidCrystal constructor is called). LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable, diff --git a/ArduinoAddons/Arduino_1.x.x/libraries/U8glib/utility/chessengine.c b/ArduinoAddons/Arduino_1.x.x/libraries/U8glib/utility/chessengine.c index f86bf0687e..4a8758c382 100644 --- a/ArduinoAddons/Arduino_1.x.x/libraries/U8glib/utility/chessengine.c +++ b/ArduinoAddons/Arduino_1.x.x/libraries/U8glib/utility/chessengine.c @@ -72,7 +72,7 @@ - Castling: Need to check for fields under attack --> done - - Check for WIN / LOOSE situation, perhaps call ce_Eval() once on the top-level board setup + - Check for WIN / LOSE situation, perhaps call ce_Eval() once on the top-level board setup just after the real move - cleanup cu_Move --> almost done diff --git a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega/ATmegaBOOT_168.c b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega/ATmegaBOOT_168.c index 9354a78cdd..1df3f03113 100644 --- a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega/ATmegaBOOT_168.c +++ b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega/ATmegaBOOT_168.c @@ -301,7 +301,7 @@ int main(void) WDTCSR = 0; // Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot. - if (! (ch & _BV(EXTRF))) // if its a not an external reset... + if (! (ch & _BV(EXTRF))) // if it's a not an external reset... app_start(); // skip bootloader #else asm volatile("nop\n\t"); diff --git a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c index fd19d14ae6..51bd8d5f84 100644 --- a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c +++ b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c @@ -172,7 +172,7 @@ int main(void) WDTCSR = 0; // Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot. - if (! (ch & _BV(EXTRF))) // if its a not an external reset... + if (! (ch & _BV(EXTRF))) // if it's a not an external reset... app_start(); // skip bootloader #endif diff --git a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c.tst b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c.tst index 733542d4af..7e0adffae2 100644 --- a/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c.tst +++ b/ArduinoAddons/Arduino_1.x.x/sanguino/bootloaders/atmega644p/ATmegaBOOT.c.tst @@ -172,7 +172,7 @@ int main(void) WDTCSR = 0; // Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot. - if (! (ch & _BV(EXTRF))) // if its a not an external reset... + if (! (ch & _BV(EXTRF))) // if it's a not an external reset... app_start(); // skip bootloader #endif diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 9b07d14b6a..d710e37567 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1,15 +1,15 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H -// This configurtion file contains the basic settings. -// Advanced settings can be found in Configuration_adv.h +// This configuration file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration -//User specified version info of this build to display in [Pronterface, etc] terminal window during startup. -//Implementation of an idea by Prof Braino to inform user that any changes made -//to this build by the user have been successfully uploaded into firmware. +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. #define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time -#define STRING_CONFIG_H_AUTHOR "(none, default config)" //Who made the changes. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. // SERIAL_PORT selects which serial port should be used for communication with the host. // This allows the connection of wireless adapters (for instance) to non-default port pins. @@ -51,6 +51,9 @@ #define MOTHERBOARD 7 #endif +// Define this to set a custom name for your generic Mendel, +// #define CUSTOM_MENDEL_NAME "This Mendel" + //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) @@ -92,7 +95,7 @@ // Actual temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one -#define TEMP_WINDOW 1 // (degC) Window around target to start the recidency timer x degC early. +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. // The minimal temperature defines the temperature below which the heater will not be enabled It is used // to check that the wiring to the thermistor is not broken. @@ -126,7 +129,7 @@ #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term - #define K1 0.95 //smoothing factor withing the PID + #define K1 0.95 //smoothing factor within the PID #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine // If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it @@ -147,20 +150,20 @@ #endif // PIDTEMP // Bed Temperature Control -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis // -// uncomment this to enable PID on the bed. It uses the same ferquency PWM as the extruder. +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. // If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you proabaly +// If your configuration is significantly different than this and you don't understand the issues involved, you probably // shouldn't use bed PID until someone else verifies your hardware works. // If this is enabled, find your own PID constants below. //#define PIDTEMPBED // //#define BED_LIMIT_SWITCHING -// This sets the max power delived to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) // setting this to anything other than 256 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) @@ -168,7 +171,7 @@ #ifdef PIDTEMPBED //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, argressive factor of .15 (vs .1, 1, 10) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) #define DEFAULT_bedKp 10.00 #define DEFAULT_bedKi .023 #define DEFAULT_bedKd 305.4 @@ -200,11 +203,11 @@ // Uncomment the following line to enable CoreXY kinematics // #define COREXY -// corse Endstop Settings +// coarse Endstop Settings #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #ifndef ENDSTOPPULLUPS - // fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined + // fine Enstop settings: Individual Pullups. will be ignored if ENDSTOPPULLUPS is defined #define ENDSTOPPULLUP_XMAX #define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_ZMAX @@ -253,8 +256,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define Y_HOME_DIR -1 #define Z_HOME_DIR -1 -#define min_software_endstops true //If true, axis won't move to coordinates less than HOME_POS. -#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below. +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // Travel limits after homing #define X_MAX_POS 205 #define X_MIN_POS 0 @@ -282,12 +285,12 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // default settings -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for Ultimaker #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts +#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). diff --git a/Marlin/LiquidCrystalRus.cpp b/Marlin/LiquidCrystalRus.cpp index 4bd8de781d..c193e449db 100644 --- a/Marlin/LiquidCrystalRus.cpp +++ b/Marlin/LiquidCrystalRus.cpp @@ -36,7 +36,7 @@ const PROGMEM uint8_t utf_recode[] = // S = 0; No shift // // Note, however, that resetting the Arduino doesn't reset the LCD, so we -// can't assume that its in that state when a sketch starts (and the +// can't assume that it's in that state when a sketch starts (and the // LiquidCrystal constructor is called). // // modified 27 Jul 2011 diff --git a/Marlin/language.h b/Marlin/language.h index 6079ba7b01..ea43c1bbc3 100644 --- a/Marlin/language.h +++ b/Marlin/language.h @@ -3,8 +3,8 @@ // NOTE: IF YOU CHANGE THIS FILE / MERGE THIS FILE WITH CHANGES // -// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" -// ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS +// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" +// ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS // Languages // 1 English @@ -30,7 +30,11 @@ #define MACHINE_NAME "Rumba" #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/" #else - #define MACHINE_NAME "Mendel" + #ifdef CUSTOM_MENDEL_NAME + #define MACHINE_NAME CUSTOM_MENDEL_NAME + #else + #define MACHINE_NAME "Mendel" + #endif #define FIRMWARE_URL "http://www.mendel-parts.com" #endif @@ -75,9 +79,9 @@ #define MSG_PID_D "PID-D" #define MSG_PID_C "PID-C" #define MSG_ACC "Accel" - #define MSG_VXY_JERK "Vxy-jerk" - #define MSG_VZ_JERK "Vz-jerk" - #define MSG_VE_JERK "Ve-jerk" + #define MSG_VXY_JERK "Vxy-jerk" + #define MSG_VZ_JERK "Vz-jerk" + #define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX "Vmax " #define MSG_X "x" #define MSG_Y "y" @@ -188,7 +192,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file" #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir: " - #define MSG_STEPPER_TO_HIGH "Steprate to high: " + #define MSG_STEPPER_TOO_HIGH "Steprate too high: " #define MSG_ENDSTOPS_HIT "endstops hit: " #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented" #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented" @@ -235,8 +239,8 @@ #define MSG_PID_C "PID-C" #define MSG_ACC "Acc" #define MSG_VXY_JERK "Zryw Vxy" - #define MSG_VZ_JERK "Zryw Vz" - #define MSG_VE_JERK "Zryw Ve" + #define MSG_VZ_JERK "Zryw Vz" + #define MSG_VE_JERK "Zryw Ve" #define MSG_VMAX "Vmax" #define MSG_X "x" #define MSG_Y "y" @@ -348,7 +352,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "blad podczas zapisu do pliku" #define MSG_SD_CANT_ENTER_SUBDIR "Nie mozna odczytac podkatalogu: " - #define MSG_STEPPER_TO_HIGH "Za duza czestotliwosc krokow: " + #define MSG_STEPPER_TOO_HIGH "Za duza czestotliwosc krokow: " #define MSG_ENDSTOPS_HIT "Wylacznik krancowy zostal wyzwolony na pozycji: " #define MSG_ERR_COLD_EXTRUDE_STOP " uniemozliwiono zimna ekstruzje" #define MSG_ERR_LONG_EXTRUDE_STOP " uniemozliwiono zbyt dluga ekstruzje" @@ -396,8 +400,8 @@ #define MSG_PID_C " PID-C: " #define MSG_ACC " Acc:" #define MSG_VXY_JERK "Vxy-jerk" -#define MSG_VZ_JERK "Vz-jerk" -#define MSG_VE_JERK "Ve-jerk" +#define MSG_VZ_JERK "Vz-jerk" +#define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX " Vmax " #define MSG_X "x:" #define MSG_Y "y:" @@ -512,7 +516,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "Erreur d'ecriture dans le fichier" #define MSG_SD_CANT_ENTER_SUBDIR "Impossible d'entrer dans le sous-repertoire: " -#define MSG_STEPPER_TO_HIGH "Steprate trop eleve: " +#define MSG_STEPPER_TOO_HIGH "Steprate trop eleve: " #define MSG_ENDSTOPS_HIT "Fin de course atteint: " #define MSG_ERR_COLD_EXTRUDE_STOP " Extrusion a froid evitee" #define MSG_ERR_LONG_EXTRUDE_STOP " Extrusion longue evitee" @@ -561,8 +565,8 @@ #define MSG_PID_C "PID-C" #define MSG_ACC "Acc" #define MSG_VXY_JERK "Vxy-jerk" - #define MSG_VZ_JERK "Vz-jerk" - #define MSG_VE_JERK "Ve-jerk" + #define MSG_VZ_JERK "Vz-jerk" + #define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX "Vmax " #define MSG_X "x" #define MSG_Y "y" @@ -674,7 +678,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "error writing to file" #define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:" - #define MSG_STEPPER_TO_HIGH "Steprate to high : " + #define MSG_STEPPER_TOO_HIGH "Steprate too high : " #define MSG_ENDSTOPS_HIT "endstops hit: " #define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented" #define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented" @@ -721,8 +725,8 @@ #define MSG_PID_C " PID-C: " #define MSG_ACC " Acc:" #define MSG_VXY_JERK " Vxy-jerk: " -#define MSG_VZ_JERK "Vz-jerk" -#define MSG_VE_JERK "Ve-jerk" +#define MSG_VZ_JERK "Vz-jerk" +#define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX " Vmax " #define MSG_X "x:" #define MSG_Y "y:" @@ -835,7 +839,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "Error al escribir en el archivo" #define MSG_SD_CANT_ENTER_SUBDIR "No se puede abrir la carpeta:" -#define MSG_STEPPER_TO_HIGH "Steprate demasiado alto : " +#define MSG_STEPPER_TOO_HIGH "Steprate demasiado alto : " #define MSG_ENDSTOPS_HIT "Se ha tocado el fin de carril: " #define MSG_ERR_COLD_EXTRUDE_STOP " extrusion fria evitada" #define MSG_ERR_LONG_EXTRUDE_STOP " extrusion demasiado larga evitada" @@ -881,8 +885,8 @@ #define MSG_PID_C " PID-C: " #define MSG_ACC " Acc:" #define MSG_VXY_JERK " Vxy-jerk: " -#define MSG_VZ_JERK "Vz-jerk" -#define MSG_VE_JERK "Ve-jerk" +#define MSG_VZ_JERK "Vz-jerk" +#define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX " Vmax " #define MSG_X "x:" #define MSG_Y "y:" @@ -989,7 +993,7 @@ #define MSG_SD_NOT_PRINTING "нет SD печати" #define MSG_SD_ERR_WRITE_TO_FILE "ошибка записи в файл" #define MSG_SD_CANT_ENTER_SUBDIR "Не зайти в папку:" -#define MSG_STEPPER_TO_HIGH "Частота шагов очень высока : " +#define MSG_STEPPER_TOO_HIGH "Частота шагов очень высока : " #define MSG_ENDSTOPS_HIT "концевик сработал: " #define MSG_ERR_COLD_EXTRUDE_STOP " защита холодной экструзии" #define MSG_ERR_LONG_EXTRUDE_STOP " защита превышения длинны экструзии" @@ -1036,8 +1040,8 @@ #define MSG_PID_C "PID-C" #define MSG_ACC "Accel" #define MSG_VXY_JERK "Vxy-jerk" - #define MSG_VZ_JERK "Vz-jerk" - #define MSG_VE_JERK "Ve-jerk" + #define MSG_VZ_JERK "Vz-jerk" + #define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX "Vmax" #define MSG_X "x" #define MSG_Y "y" @@ -1149,7 +1153,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "Errore nella scrittura su file" #define MSG_SD_CANT_ENTER_SUBDIR "Impossibile entrare nella sottocartella: " - #define MSG_STEPPER_TO_HIGH "Steprate troppo alto: " + #define MSG_STEPPER_TOO_HIGH "Steprate troppo alto: " #define MSG_ENDSTOPS_HIT "Raggiunto il fondo carrello: " #define MSG_ERR_COLD_EXTRUDE_STOP " prevenuta estrusione fredda" #define MSG_ERR_LONG_EXTRUDE_STOP " prevenuta estrusione troppo lunga" @@ -1198,8 +1202,8 @@ #define MSG_PID_C " PID-C: " #define MSG_ACC " Acc:" #define MSG_VXY_JERK " Vxy-jerk: " - #define MSG_VZ_JERK "Vz-jerk" - #define MSG_VE_JERK "Ve-jerk" + #define MSG_VZ_JERK "Vz-jerk" + #define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX " Vmax " #define MSG_X "x:" #define MSG_Y "y:" @@ -1246,8 +1250,8 @@ #define MSG_CONTROL_RETRACT_RECOVER " DesRet +mm:" #define MSG_CONTROL_RETRACT_RECOVERF " DesRet F:" #define MSG_AUTORETRACT " AutoRetr.:" - #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Algo esta errado na estrutura do Menu." - #define MSG_FILAMENTCHANGE "Change filament" + #define MSG_SERIAL_ERROR_MENU_STRUCTURE "Algo esta errado na estrutura do Menu." + #define MSG_FILAMENTCHANGE "Change filament" // Serial Console Messages @@ -1315,7 +1319,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "Erro ao escrever no arquivo" #define MSG_SD_CANT_ENTER_SUBDIR "Nao pode abrir o sub diretorio:" - #define MSG_STEPPER_TO_HIGH "Steprate muito alto : " + #define MSG_STEPPER_TOO_HIGH "Steprate muito alto : " #define MSG_ENDSTOPS_HIT "O ponto final foi tocado: " #define MSG_ERR_COLD_EXTRUDE_STOP " Extrusao a frio evitada" #define MSG_ERR_LONG_EXTRUDE_STOP " Extrusao muito larga evitada" @@ -1366,8 +1370,8 @@ #define MSG_PID_C "PID-C" #define MSG_ACC "Kiihtyv" #define MSG_VXY_JERK "Vxy-jerk" - #define MSG_VZ_JERK "Vz-jerk" - #define MSG_VE_JERK "Ve-jerk" + #define MSG_VZ_JERK "Vz-jerk" + #define MSG_VE_JERK "Ve-jerk" #define MSG_VMAX "Vmax " #define MSG_X "x" #define MSG_Y "y" @@ -1476,7 +1480,7 @@ #define MSG_SD_ERR_WRITE_TO_FILE "virhe kirjoitettaessa tiedostoon" #define MSG_SD_CANT_ENTER_SUBDIR "Alihakemistoon ei voitu siirtya: " - #define MSG_STEPPER_TO_HIGH "Askellustaajuus liian suuri: " + #define MSG_STEPPER_TOO_HIGH "Askellustaajuus liian suuri: " #define MSG_ENDSTOPS_HIT "paatyrajat aktivoitu: " #define MSG_ERR_COLD_EXTRUDE_STOP " kylmana pursotus estetty" #define MSG_ERR_LONG_EXTRUDE_STOP " liian pitka pursotus estetty" diff --git a/Marlin/pins.h b/Marlin/pins.h index 2424010aa5..044f083f8d 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -429,7 +429,7 @@ #else //old style panel with shift register //arduino pin witch triggers an piezzo beeper - #define BEEPER 33 No Beeper added + #define BEEPER 33 // No Beeper added //buttons are attached to a shift register // Not wired this yet diff --git a/Marlin/stepper.cpp b/Marlin/stepper.cpp index 3bc5e9c892..10e8fae2dd 100644 --- a/Marlin/stepper.cpp +++ b/Marlin/stepper.cpp @@ -69,9 +69,9 @@ volatile long endstops_stepsTotal,endstops_stepsDone; static volatile bool endstop_x_hit=false; static volatile bool endstop_y_hit=false; static volatile bool endstop_z_hit=false; -#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED -bool abort_on_endstop_hit = false; -#endif +#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED +bool abort_on_endstop_hit = false; +#endif static bool old_x_min_endstop=false; static bool old_x_max_endstop=false; @@ -184,20 +184,20 @@ void checkHitEndstops() SERIAL_ECHOPAIR(" Z:",(float)endstops_trigsteps[Z_AXIS]/axis_steps_per_unit[Z_AXIS]); LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "Z"); } - SERIAL_ECHOLN(""); + SERIAL_ECHOLN(""); endstop_x_hit=false; endstop_y_hit=false; - endstop_z_hit=false; -#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED - if (abort_on_endstop_hit) - { + endstop_z_hit=false; +#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + if (abort_on_endstop_hit) + { card.sdprinting = false; card.closefile(); - quickStop(); + quickStop(); setTargetHotend0(0); setTargetHotend1(0); setTargetHotend2(0); - } + } #endif } } @@ -272,7 +272,7 @@ FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) { timer = (unsigned short)pgm_read_word_near(table_address); timer -= (((unsigned short)pgm_read_word_near(table_address+2) * (unsigned char)(step_rate & 0x0007))>>3); } - if(timer < 100) { timer = 100; MYSERIAL.print(MSG_STEPPER_TO_HIGH); MYSERIAL.println(step_rate); }//(20kHz this should never happen) + if(timer < 100) { timer = 100; MYSERIAL.print(MSG_STEPPER_TOO_HIGH); MYSERIAL.println(step_rate); }//(20kHz this should never happen) return timer; } diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 85017750be..44c144cde7 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -257,7 +257,7 @@ void PID_autotune(float temp, int extruder, int ncycles) } } if(input > (temp + 20)) { - SERIAL_PROTOCOLLNPGM("PID Autotune failed! Temperature to high"); + SERIAL_PROTOCOLLNPGM("PID Autotune failed! Temperature too high"); return; } if(millis() - temp_millis > 2000) { @@ -281,7 +281,7 @@ void PID_autotune(float temp, int extruder, int ncycles) return; } if(cycles > ncycles) { - SERIAL_PROTOCOLLNPGM("PID Autotune finished ! Place the Kp, Ki and Kd constants in the configuration.h"); + SERIAL_PROTOCOLLNPGM("PID Autotune finished! Put the Kp, Ki and Kd constants into Configuration.h"); return; } lcd_update(); @@ -904,7 +904,7 @@ int read_max6675() // Timer 0 is shared with millies ISR(TIMER0_COMPB_vect) { - //these variables are only accesible from the ISR, but static, so they don't loose their value + //these variables are only accesible from the ISR, but static, so they don't lose their value static unsigned char temp_count = 0; static unsigned long raw_temp_0_value = 0; static unsigned long raw_temp_1_value = 0;