mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 20:18:52 +00:00
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
This commit is contained in:
Johann Rocholl
parent
6aa87a7b67
commit
a30007caa4
206
Marlin/pins.h
206
Marlin/pins.h
@ -957,198 +957,68 @@
|
||||
#endif
|
||||
|
||||
/****************************************************************************************
|
||||
* Teensylu 0.7 pin assingments (ATMEGA90USB)
|
||||
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 8
|
||||
#define MOTHERBOARD 8
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
|
||||
#define X_STEP_PIN 0
|
||||
#define X_DIR_PIN 1
|
||||
#define X_ENABLE_PIN 39
|
||||
#define X_MIN_PIN 13
|
||||
#define X_MAX_PIN -1
|
||||
|
||||
#define Y_STEP_PIN 2
|
||||
#define Y_DIR_PIN 3
|
||||
#define Y_ENABLE_PIN 38
|
||||
#define Y_MIN_PIN 14
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 4
|
||||
#define Z_DIR_PIN 5
|
||||
#define Z_ENABLE_PIN 23
|
||||
#define Z_MIN_PIN 15
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 6
|
||||
#define E0_DIR_PIN 7
|
||||
#define E0_ENABLE_PIN 19
|
||||
|
||||
|
||||
|
||||
#define HEATER_0_PIN 21 // Extruder
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define HEATER_BED_PIN 20 // Bed
|
||||
#define FAN_PIN 22 // Fan
|
||||
|
||||
#define TEMP_0_PIN 7 // Extruder
|
||||
#define TEMP_1_PIN -1
|
||||
#define TEMP_2_PIN -1
|
||||
#define TEMP_BED_PIN 6 // Bed
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 8
|
||||
#define LED_PIN -1
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
#define ALARM_PIN -1
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
// these pins are defined in the SD library if building with SD support
|
||||
#define SCK_PIN 9
|
||||
#define MISO_PIN 11
|
||||
#define MOSI_PIN 10
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/****************************************************************************************
|
||||
* Printrboard Rev. B pin assingments (ATMEGA90USB1286)
|
||||
* Requires the Teensyduino software with Teensy++ 2.0 selected in arduino IDE!
|
||||
* Teensylu 0.7 / Printrboard pin assignments (AT90USB1286)
|
||||
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
|
||||
http://www.pjrc.com/teensy/teensyduino.html
|
||||
* See http://reprap.org/wiki/Printrboard for more info
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 81
|
||||
#if MOTHERBOARD == 8 || MOTHERBOARD == 81
|
||||
#undef MOTHERBOARD
|
||||
#define MOTHERBOARD 8 // Disable MarlinSerial etc.
|
||||
#define MOTHERBOARD 8
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_AT90USB1286__
|
||||
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
||||
#define X_STEP_PIN 28
|
||||
#define X_DIR_PIN 29
|
||||
#define X_ENABLE_PIN 19
|
||||
#define X_MIN_PIN 47
|
||||
#define X_STEP_PIN 0
|
||||
#define X_DIR_PIN 1
|
||||
#define X_ENABLE_PIN 39
|
||||
#define X_MIN_PIN 13
|
||||
#define X_MAX_PIN -1
|
||||
|
||||
#define Y_STEP_PIN 30
|
||||
#define Y_DIR_PIN 31
|
||||
#define Y_ENABLE_PIN 18
|
||||
#define Y_MIN_PIN 20
|
||||
#define Y_STEP_PIN 2
|
||||
#define Y_DIR_PIN 3
|
||||
#define Y_ENABLE_PIN 38
|
||||
#define Y_MIN_PIN 14
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 32
|
||||
#define Z_DIR_PIN 33
|
||||
#define Z_ENABLE_PIN 17
|
||||
#define Z_MIN_PIN 36
|
||||
#define Z_STEP_PIN 4
|
||||
#define Z_DIR_PIN 5
|
||||
#define Z_ENABLE_PIN 23
|
||||
#define Z_MIN_PIN 15
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 34
|
||||
#define E0_DIR_PIN 35
|
||||
#define E0_ENABLE_PIN 13
|
||||
#define E0_STEP_PIN 6
|
||||
#define E0_DIR_PIN 7
|
||||
#define E0_ENABLE_PIN 19
|
||||
|
||||
#define HEATER_0_PIN 15 // Extruder
|
||||
#define HEATER_0_PIN 21 // Extruder
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define HEATER_BED_PIN 14 // Bed
|
||||
#define FAN_PIN 16 // Fan
|
||||
#define HEATER_BED_PIN 20 // Bed
|
||||
#define FAN_PIN 22
|
||||
|
||||
#define TEMP_0_PIN 1 // Extruder - ANALOG PIN NUMBERING
|
||||
#define TEMP_0_PIN 7 // Extruder / Analog PIN numbering
|
||||
#define TEMP_1_PIN -1
|
||||
#define TEMP_2_PIN -1
|
||||
#define TEMP_BED_PIN 0 // Bed - ANALOG PIN NUMBERING
|
||||
#define TEMP_BED_PIN 6 // Bed / Analog PIN numbering
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 26
|
||||
#define SDSS 8
|
||||
#define LED_PIN -1
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
#define ALARM_PIN -1
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
// these pins are defined in the SD library if building with SD support
|
||||
#define SCK_PIN 21
|
||||
#define MISO_PIN 22
|
||||
#define MOSI_PIN 23
|
||||
#define SCK_PIN 9
|
||||
#define MISO_PIN 11
|
||||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
#ifdef ULTRA_LCD
|
||||
|
||||
#ifdef NEWPANEL
|
||||
//arduino pin which triggers an piezzo beeper
|
||||
#define BEEPER 33 // Beeper on AUX-4
|
||||
|
||||
#ifndef MCP28017_LCD
|
||||
#define LCD_PINS_RS 16
|
||||
#define LCD_PINS_ENABLE 17
|
||||
#define LCD_PINS_D4 23
|
||||
#define LCD_PINS_D5 25
|
||||
#define LCD_PINS_D6 27
|
||||
#define LCD_PINS_D7 29
|
||||
#endif // MCP28017_LCD
|
||||
|
||||
//buttons are directly attached using AUX-2
|
||||
#define BTN_EN1 11 // PC1
|
||||
#define BTN_EN2 12 // PC2
|
||||
#ifndef VERSAPANEL
|
||||
#define BTN_ENC 31 //the click
|
||||
#endif
|
||||
|
||||
#define BLEN_C 2
|
||||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Ramps does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#else //old style panel with shift register
|
||||
//arduino pin witch triggers an piezzo beeper
|
||||
#define BEEPER 33 No Beeper added
|
||||
|
||||
//buttons are attached to a shift register
|
||||
// Not wired this yet
|
||||
//#define SHIFT_CLK 38
|
||||
//#define SHIFT_LD 42
|
||||
//#define SHIFT_OUT 40
|
||||
//#define SHIFT_EN 17
|
||||
|
||||
#define LCD_PINS_RS 16
|
||||
#define LCD_PINS_ENABLE 17
|
||||
#define LCD_PINS_D4 23
|
||||
#define LCD_PINS_D5 25
|
||||
#define LCD_PINS_D6 27
|
||||
#define LCD_PINS_D7 29
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
//bits in the shift register that carry the buttons for:
|
||||
// left up center down right red
|
||||
#define BL_LE 7
|
||||
#define BL_UP 6
|
||||
#define BL_MI 5
|
||||
#define BL_DW 4
|
||||
#define BL_RI 3
|
||||
#define BL_ST 2
|
||||
|
||||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
#endif
|
||||
#endif //ULTRA_LCD
|
||||
|
||||
#endif
|
||||
#endif // MOTHERBOARD == 8 (Teensylu) or 81 (Printrboard)
|
||||
|
||||
/****************************************************************************************
|
||||
* Brainwave 1.0 pin assignments (AT90USB646)
|
||||
@ -1185,10 +1055,10 @@
|
||||
#define Z_MAX_PIN -1
|
||||
#define Z_ATT_PIN 16
|
||||
|
||||
#define E0_STEP_PIN 21
|
||||
#define E0_DIR_PIN 23
|
||||
#define E0_ENABLE_PIN 22
|
||||
#define E0_ATT_PIN 20
|
||||
#define E0_STEP_PIN 21
|
||||
#define E0_DIR_PIN 23
|
||||
#define E0_ENABLE_PIN 22
|
||||
#define E0_ATT_PIN 20
|
||||
|
||||
#define HEATER_0_PIN 4 // Extruder
|
||||
#define HEATER_1_PIN -1
|
||||
@ -1210,12 +1080,12 @@
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
// these pins are defined in the SD library if building with SD support
|
||||
#define SCK_PIN 21
|
||||
#define MISO_PIN 22
|
||||
#define MOSI_PIN 23
|
||||
#define SCK_PIN 9
|
||||
#define MISO_PIN 11
|
||||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
#endif
|
||||
#endif // MOTHERBOARD == 82 (Brainwave)
|
||||
|
||||
/****************************************************************************************
|
||||
* Gen3+ pin assignment
|
||||
|
||||
Loading…
Reference in New Issue
Block a user