From ab0d3c4fb3c408fcb91e97ee5eb2417129cbb5d0 Mon Sep 17 00:00:00 2001 From: Mark Hanford Date: Fri, 14 Feb 2014 11:48:24 +0000 Subject: [PATCH] Various typo fixes - only in comments, no code changes. --- Marlin/Configuration.h | 44 +++++++++++++++++++------------------- Marlin/Configuration_adv.h | 28 ++++++++++++------------ 2 files changed, 36 insertions(+), 36 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 6a2c43ba3c1..752028ec15e 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -8,7 +8,7 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer rplace the configuration files wilth the files in the +// For a Delta printer replace the configuration files with the files in the // example_configurations/delta directory. // @@ -68,7 +68,7 @@ // 702= Minitronics v1.0 // 90 = Alpha OMCA board // 91 = Final OMCA board -// 301 = Rambo +// 301= Rambo // 21 = Elefu Ra Board (v3) #ifndef MOTHERBOARD @@ -91,7 +91,7 @@ #define POWER_SUPPLY 1 -// Define this to have the electronics keep the powersupply off on startup. If you don't know what this is leave it. +// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. // #define PS_DEFAULT_OFF //=========================================================================== @@ -106,7 +106,7 @@ // 0 is not used // 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) // 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is mendel-parts thermistor (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) // 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! // 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) // 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) @@ -116,7 +116,7 @@ // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) // 10 is 100k RS thermistor 198-961 (4.7k pullup) // 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermister +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor // // 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k // (but gives greater accuracy and more stable PID) @@ -177,13 +177,13 @@ #define K1 0.95 //smoothing factor within the PID #define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine -// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker #define DEFAULT_Kp 22.2 #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114 -// Makergear +// MakerGear // #define DEFAULT_Kp 7.0 // #define DEFAULT_Ki 0.1 // #define DEFAULT_Kd 12 @@ -252,7 +252,7 @@ #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #ifndef ENDSTOPPULLUPS - // fine Enstop settings: Individual Pullups. will be ignored if ENDSTOPPULLUPS is defined + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined // #define ENDSTOPPULLUP_XMAX // #define ENDSTOPPULLUP_YMAX // #define ENDSTOPPULLUP_ZMAX @@ -336,7 +336,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define BACK_PROBE_BED_POSITION 180 #define FRONT_PROBE_BED_POSITION 20 - // these are the offsets to the prob relative to the extruder tip (Hotend - Probe) + // these are the offsets to the probe relative to the extruder tip (Hotend - Probe) #define X_PROBE_OFFSET_FROM_EXTRUDER -25 #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 @@ -357,7 +357,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of // #define PROBE_SERVO_DEACTIVATION_DELAY 300 -//If you have enabled the Bed Auto Levelling and are using the same Z Probe for Z Homing, +//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, //it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area. @@ -391,7 +391,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) //Manual homing switch locations: -// For deltabots this means top and center of the cartesian print volume. +// For deltabots this means top and center of the Cartesian print volume. #define MANUAL_X_HOME_POS 0 #define MANUAL_Y_HOME_POS 0 #define MANUAL_Z_HOME_POS 0 @@ -405,7 +405,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. +#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts @@ -426,11 +426,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //=========================================================================== // EEPROM -// the microcontroller can store settings in the EEPROM, e.g. max velocity... -// M500 - stores paramters in EEPROM +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. -//define this to enable eeprom support +//define this to enable EEPROM support //#define EEPROM_SETTINGS //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // please keep turned on if you can. @@ -446,14 +446,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 //LCD and SD support -//#define ULTRA_LCD //general lcd support, also 16x2 +//#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking -//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store. -//#define ULTIPANEL //the ultipanel as on thingiverse +//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. +//#define ULTIPANEL //the UltiPanel as on Thingiverse //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click @@ -578,7 +578,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection //#define SR_LCD #ifdef SR_LCD - #define SR_LCD_2W_NL // Non latching 2 wire shiftregister + #define SR_LCD_2W_NL // Non latching 2 wire shift register //#define NEWPANEL #endif @@ -594,7 +594,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define LCD_WIDTH 20 #define LCD_HEIGHT 4 #endif -#else //no panel but just lcd +#else //no panel but just LCD #ifdef ULTRA_LCD #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display #define LCD_WIDTH 20 @@ -616,8 +616,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino //#define FAST_PWM_FAN -// Temperature status leds that display the hotend and bet temperature. -// If alle hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Temperature status LEDs that display the hotend and bet temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. // Otherwise the RED led is on. There is 1C hysteresis. //#define TEMP_STAT_LEDS diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index dc986fae4af..67cbfcc80f5 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -11,7 +11,7 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control //// Heating sanity check: -// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature +// This waits for the watch period in milliseconds whenever an M104 or M109 increases the target temperature // If the temperature has not increased at the end of that period, the target temperature is set to zero. // It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature // differ by at least 2x WATCH_TEMP_INCREASE @@ -19,11 +19,11 @@ //#define WATCH_TEMP_INCREASE 10 //Heat up at least 10 degree in 20 seconds #ifdef PIDTEMP - // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed. - // if Kc is choosen well, the additional required power due to increased melting should be compensated. + // this adds an experimental additional term to the heating power, proportional to the extrusion speed. + // if Kc is chosen well, the additional required power due to increased melting should be compensated. #define PID_ADD_EXTRUSION_RATE #ifdef PID_ADD_EXTRUSION_RATE - #define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed) + #define DEFAULT_Kc (1) //heating power=Kc*(e_speed) #endif #endif @@ -34,7 +34,7 @@ // the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp // you exit the value by any M109 without F* // Also, if the temperature is set to a value