diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index b529d9ee12f..0fba67b2b33 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h
index 59bf7e018cd..c60284a9e4d 100644
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h
index 1bf4103c729..07fa3d8bc3b 100644
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index 7866b7da310..514e0f3c364 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h
index cf6b6faa3d2..1f207cb8277 100644
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
index 96c86144915..dc31b7ca89f 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index 65394660355..d7ec88d2212 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index 17251939521..e3d85ad88e6 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
index 61373b3ed80..4a09907ff02 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@@ -40,16 +40,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -60,14 +50,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index 6e5921dd3f0..640a2b7ff66 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index 01b15afa49c..75c7c2095eb 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -36,16 +36,6 @@
   #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif
 
-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -56,14 +46,16 @@
   #endif
 #endif
 
-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
   #define AUTOTEMP_OLDWEIGHT 0.98