diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 4694afd453..7c89a4152d 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -3,6 +3,20 @@
 
 #include "boards.h"
 
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
@@ -67,7 +81,7 @@
 // #define PS_DEFAULT_OFF
 
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings  ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -143,7 +157,11 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -183,7 +201,9 @@
 
 #endif // PIDTEMP
 
-// Bed Temperature Control
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -220,7 +240,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -230,7 +249,10 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -265,11 +287,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================= Mechanical Settings =========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -341,7 +362,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units in mm)
 #define X_MAX_POS 215
 #define X_MIN_POS 0
 #define Y_MAX_POS 210
@@ -352,7 +373,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 #define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
@@ -505,8 +530,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================= Additional Features =========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index 888835e7b1..99ad1b8df5 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -3,6 +3,21 @@
 
 #include "boards.h"
 
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
@@ -66,8 +81,9 @@
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
+
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -143,7 +159,11 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -182,7 +202,9 @@
    #define  DEFAULT_Kd 93.51
 #endif // PIDTEMP
 
-// Bed Temperature Control
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -225,7 +247,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -235,7 +256,11 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -270,11 +295,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================= Mechanical Settings =========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -346,7 +370,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 200
 #define X_MIN_POS 0
 #define Y_MAX_POS 200
@@ -357,7 +381,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 #define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
@@ -510,8 +538,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================= Additional Features =========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index 7d52562c44..ea2495ddf1 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -3,6 +3,22 @@
 
 #include "boards.h"
 
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
@@ -86,7 +102,7 @@
 // #define PS_DEFAULT_OFF
 
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -161,7 +177,11 @@
 #define EXTRUDER_WATTS (2*2/5.9) //  P=I^2/R
 #define BED_WATTS (5.45*5.45/2.2)      // P=I^2/R
 
-// PID settings:
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -202,7 +222,9 @@
    // #define  DEFAULT_Kd 440
 #endif // PIDTEMP
 
-// Bed Temperature Control
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -255,7 +277,11 @@
 #define EXTRUDE_MINTEMP 150
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -290,10 +316,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
+
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================ Mechanical Settings ==========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -365,7 +391,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 200
 #define X_MIN_POS 0
 #define Y_MAX_POS 200
@@ -376,7 +402,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 
@@ -503,8 +533,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4    // (mm/sec)
 #define DEFAULT_EJERK                 3    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================= Additional Features =========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index dea6c72a01..6a13e33c37 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -3,6 +3,22 @@
 
 #include "boards.h"
 
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
@@ -66,8 +82,9 @@
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
+
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -143,7 +160,12 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -182,7 +204,9 @@
       #define  DEFAULT_Kd 114
 #endif // PIDTEMP
 
-// Bed Temperature Control
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -219,7 +243,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -229,7 +252,11 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -264,11 +291,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================= Mechanical Settings =========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -340,7 +366,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 297
 #define X_MIN_POS 0
 #define Y_MAX_POS 210
@@ -351,7 +377,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 #define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
@@ -504,8 +534,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================ Additional Features ==========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/delta/Configuration.h b/Marlin/example_configurations/delta/Configuration.h
index 347c346090..e8d620e2a9 100644
--- a/Marlin/example_configurations/delta/Configuration.h
+++ b/Marlin/example_configurations/delta/Configuration.h
@@ -3,10 +3,26 @@
 
 #include "boards.h"
 
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
+
 //===========================================================================
 //============================= DELTA Printer ===============================
 //===========================================================================
@@ -59,6 +75,7 @@
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
+
 //===========================================================================
 //============================== Delta Settings =============================
 //===========================================================================
@@ -87,8 +104,9 @@
 // Effective horizontal distance bridged by diagonal push rods.
 #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
 
+
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -164,7 +182,12 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -195,7 +218,10 @@
 //    #define  DEFAULT_Kd 440
 #endif // PIDTEMP
 
-// Bed Temperature Control
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -232,7 +258,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -242,7 +267,11 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -277,11 +306,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================= Mechanical Settings =========================
 //===========================================================================
 
 // coarse Endstop Settings
@@ -352,7 +380,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 90
 #define X_MIN_POS -90
 #define Y_MAX_POS 90
@@ -363,7 +391,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
+
 //Bed Auto Leveling is still not compatible with Delta Kinematics
 
 
@@ -408,7 +440,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
 //===========================================================================
-//=============================Additional Features===========================
+//============================= Additional Features =========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 0781ed60a6..827e67ced0 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -3,10 +3,27 @@
 
 #include "boards.h"
 
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
+
 //===========================================================================
 //============================= DELTA Printer ===============================
 //===========================================================================
@@ -14,6 +31,7 @@
 // example_configurations/delta directory.
 //
 
+
 //===========================================================================
 //============================= SCARA Printer ===============================
 //===========================================================================
@@ -66,8 +84,9 @@
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
+
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -143,7 +162,12 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -174,7 +198,10 @@
 //    #define  DEFAULT_Kd 440
 #endif // PIDTEMP
 
-// Bed Temperature Control
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -214,7 +241,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -224,7 +250,11 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
+//===========================================================================
+//============================= Thermal Runaway Protection ==================
+//===========================================================================
+/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -259,11 +289,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================ Mechanical Settings ==========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -335,7 +364,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 110
 #define X_MIN_POS 0
 #define Y_MAX_POS 150
@@ -346,7 +375,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 #define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
@@ -475,8 +508,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================ Additional Features ==========================
 //===========================================================================
 
 // Custom M code points
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index b362753e81..47a6c3e054 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -3,10 +3,26 @@
 
 #include "boards.h"
 
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+/*
+Here are some standard links for getting your machine calibrated:
+ * http://reprap.org/wiki/Calibration 
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+*/
+
+
 // This configuration file contains the basic settings.
 // Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
+
 //===========================================================================
 //============================= DELTA Printer ===============================
 //===========================================================================
@@ -14,6 +30,7 @@
 // example_configurations/delta directory.
 //
 
+
 //===========================================================================
 //============================= SCARA Printer ===============================
 //===========================================================================
@@ -66,8 +83,9 @@
 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
+
 //===========================================================================
-//=============================Thermal Settings  ============================
+//============================= Thermal Settings ============================
 //===========================================================================
 //
 //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
@@ -145,7 +163,12 @@
 //#define EXTRUDER_WATTS (12.0*12.0/6.7) //  P=I^2/R
 //#define BED_WATTS (12.0*12.0/1.1)      // P=I^2/R
 
-// PID settings:
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
 // Comment the following line to disable PID and enable bang-bang.
 #define PIDTEMP
 #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
@@ -181,7 +204,10 @@
 //    #define  DEFAULT_Kd 440
 #endif // PIDTEMP
 
-// Bed Temperature Control
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
 // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
 // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
@@ -218,7 +244,6 @@
 #endif // PIDTEMPBED
 
 
-
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
@@ -228,7 +253,11 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
-/*================== Thermal Runaway Protection ==============================
+
++//===========================================================================
++//============================= Thermal Runaway Protection ==================
++//===========================================================================
++/*
 This is a feature to protect your printer from burn up in flames if it has
 a thermistor coming off place (this happened to a friend of mine recently and
 motivated me writing this feature).
@@ -263,11 +292,10 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Parameters for the bed heater
 //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
 //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
-//===========================================================================
 
 
 //===========================================================================
-//=============================Mechanical Settings===========================
+//============================ Mechanical Settings ==========================
 //===========================================================================
 
 // Uncomment the following line to enable CoreXY kinematics
@@ -339,7 +367,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing
+// Travel limits after homing (units are in mm)
 #define X_MAX_POS 205
 #define X_MIN_POS 0
 #define Y_MAX_POS 205
@@ -350,7 +378,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
 #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
 #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+
+
+//===========================================================================
 //============================= Bed Auto Leveling ===========================
+//===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
 #define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
@@ -489,8 +521,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_ZJERK                 0.4     // (mm/sec)
 #define DEFAULT_EJERK                 5.0    // (mm/sec)
 
+
 //===========================================================================
-//=============================Additional Features===========================
+//============================ Additional Features ==========================
 //===========================================================================
 
 // Custom M code points