diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 54a895712d..77f1908901 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1388,8 +1388,10 @@
 /**
  * Z Servo Probe, such as an endstop switch on a rotating arm.
  */
-//#define Z_PROBE_SERVO_NR 0       // Defaults to SERVO 0 connector.
-//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
+//#define Z_PROBE_SERVO_NR 0          // Defaults to SERVO 0 connector.
+//#define Z_SERVO_ANGLES { 70, 0 }    // Z Servo Deploy and Stow angles
+//#define Z_SERVO_MEASURE_ANGLE 45    // Use if the servo must move to a "free" position for measuring after deploy.
+//#define Z_SERVO_INTERMEDIATE_STOW   // Stow the probe between points.
 
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
diff --git a/Marlin/src/gcode/bedlevel/abl/G29.cpp b/Marlin/src/gcode/bedlevel/abl/G29.cpp
index 4769bd79c0..114fa55520 100644
--- a/Marlin/src/gcode/bedlevel/abl/G29.cpp
+++ b/Marlin/src/gcode/bedlevel/abl/G29.cpp
@@ -491,7 +491,7 @@ G29_TYPE GcodeSuite::G29() {
     if (!no_action) set_bed_leveling_enabled(false);
 
     // Deploy certain probes before starting probing
-    #if ENABLED(BLTOUCH)
+    #if ENABLED(BLTOUCH) || BOTH(HAS_Z_SERVO_PROBE, Z_SERVO_INTERMEDIATE_STOW)
       do_z_clearance(Z_CLEARANCE_DEPLOY_PROBE);
     #elif HAS_BED_PROBE
       if (probe.deploy()) { // (returns true on deploy failure)
diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp
index f0a3c8584b..7daafd1139 100644
--- a/Marlin/src/module/probe.cpp
+++ b/Marlin/src/module/probe.cpp
@@ -405,6 +405,11 @@ FORCE_INLINE void probe_specific_action(const bool deploy) {
 
     servo[Z_PROBE_SERVO_NR].move(servo_angles[Z_PROBE_SERVO_NR][deploy ? 0 : 1]);
 
+    #ifdef Z_SERVO_MEASURE_ANGLE
+      // After deploy move back to the measure angle...
+      if (deploy) MOVE_SERVO(Z_PROBE_SERVO_NR, Z_SERVO_MEASURE_ANGLE);
+    #endif
+
   #elif ANY(TOUCH_MI_PROBE, Z_PROBE_ALLEN_KEY, MAG_MOUNTED_PROBE)
 
     deploy ? run_deploy_moves() : run_stow_moves();
@@ -582,11 +587,16 @@ bool Probe::probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s) {
   #if BOTH(HAS_TEMP_HOTEND, WAIT_FOR_HOTEND)
     thermalManager.wait_for_hotend_heating(active_extruder);
   #endif
+
   #if ENABLED(BLTOUCH)
     if (!bltouch.high_speed_mode && bltouch.deploy())
       return true; // Deploy in LOW SPEED MODE on every probe action
   #endif
 
+  #if HAS_Z_SERVO_PROBE && (ENABLED(Z_SERVO_INTERMEDIATE_STOW) || defined(Z_SERVO_MEASURE_ANGLE))
+    probe_specific_action(true);  //  Always re-deploy in this case
+  #endif
+
   // Disable stealthChop if used. Enable diag1 pin on driver.
   #if ENABLED(SENSORLESS_PROBING)
     sensorless_t stealth_states { false };
@@ -636,6 +646,10 @@ bool Probe::probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s) {
       return true; // Stow in LOW SPEED MODE on every trigger
   #endif
 
+  #if BOTH(HAS_Z_SERVO_PROBE, Z_SERVO_INTERMEDIATE_STOW)
+    probe_specific_action(false);  //  Always stow
+  #endif
+
   // Clear endstop flags
   endstops.hit_on_purpose();