mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 12:04:19 +00:00
Update Bed PID comments
This commit is contained in:
Scott Lahteine
parent
56486c5c0e
commit
dca69efc11
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -408,23 +408,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 206 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -410,23 +410,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -406,23 +406,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -387,23 +387,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -400,23 +400,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -387,23 +387,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -400,23 +400,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -413,23 +413,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -403,23 +403,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -387,23 +387,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -387,23 +387,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -409,23 +409,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -409,23 +409,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -409,23 +409,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -403,23 +403,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -409,23 +409,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -419,23 +419,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -407,23 +407,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -398,23 +398,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -402,23 +402,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -418,23 +418,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -400,23 +400,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -436,23 +436,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -410,23 +410,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -423,23 +423,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -409,23 +409,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -391,23 +391,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -403,23 +403,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -412,23 +412,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -399,23 +399,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 175 // limits duty cycle to bed; 255=full current
|
||||
// This limit is set to 175 by default in the Makibox configuration and it can be adjusted
|
||||
// to increase the heatup rate. However, if changed, be aware of the safety concerns of
|
||||
|
||||
@ -400,23 +400,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -388,23 +388,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -404,23 +404,30 @@
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
|
||||
/**
|
||||
* PID Bed Heating
|
||||
*
|
||||
* If this option is enabled set PID constants below.
|
||||
* If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
|
||||
*
|
||||
* The PID frequency will be the same as the extruder PWM.
|
||||
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
|
||||
* which is fine for driving a square wave into a resistive load and does not significantly
|
||||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
/**
|
||||
* Max Bed Power
|
||||
* Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
|
||||
* When set to any value below 255, enables a form of PWM to the bed that acts like a divider
|
||||
* so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
|
||||
*/
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user