From e2e7b1d7053a3c610b7aa791a69bcfe01b65e4d8 Mon Sep 17 00:00:00 2001
From: Roxy-3D <Roxy-3D@users.noreply.github.com>
Date: Thu, 6 Sep 2018 10:20:20 -0500
Subject: [PATCH] Break out support of the T-Rex 3
---
.../Formbot/T_Rex3/Configuration_adv.h | 1697 +++++++++++++++++
1 file changed, 1697 insertions(+)
create mode 100644 Marlin/src/config/examples/Formbot/T_Rex3/Configuration_adv.h
diff --git a/Marlin/src/config/examples/Formbot/T_Rex3/Configuration_adv.h b/Marlin/src/config/examples/Formbot/T_Rex3/Configuration_adv.h
new file mode 100644
index 00000000000..0da60da9658
--- /dev/null
+++ b/Marlin/src/config/examples/Formbot/T_Rex3/Configuration_adv.h
@@ -0,0 +1,1697 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H_VERSION 020000
+
+// @section temperature
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+
+//
+// Hephestos 2 24V heated bed upgrade kit.
+// https://store.bq.com/en/heated-bed-kit-hephestos2
+//
+//#define HEPHESTOS2_HEATED_BED_KIT
+#if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
+ #undef TEMP_SENSOR_BED
+ #define TEMP_SENSOR_BED 70
+ #define HEATER_BED_INVERTING true
+#endif
+
+#if DISABLED(PIDTEMPBED)
+ #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
+ #if ENABLED(BED_LIMIT_SWITCHING)
+ #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+ #endif
+#endif
+
+/**
+ * Thermal Protection provides additional protection to your printer from damage
+ * and fire. Marlin always includes safe min and max temperature ranges which
+ * protect against a broken or disconnected thermistor wire.
+ *
+ * The issue: If a thermistor falls out, it will report the much lower
+ * temperature of the air in the room, and the the firmware will keep
+ * the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too
+ * long (period), the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway", increase
+ * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
+ */
+#if ENABLED(THERMAL_PROTECTION_HOTENDS)
+ #define THERMAL_PROTECTION_PERIOD 60 // Seconds
+ #define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius
+
+ /**
+ * Whenever an M104, M109, or M303 increases the target temperature, the
+ * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
+ * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
+ * requires a hard reset. This test restarts with any M104/M109/M303, but only
+ * if the current temperature is far enough below the target for a reliable
+ * test.
+ *
+ * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
+ * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
+ * below 2.
+ */
+ #define WATCH_TEMP_PERIOD 60 // Seconds
+ #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+/**
+ * Thermal Protection parameters for the bed are just as above for hotends.
+ */
+#if ENABLED(THERMAL_PROTECTION_BED)
+ #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds
+ #define THERMAL_PROTECTION_BED_HYSTERESIS 5 // Degrees Celsius
+
+ /**
+ * As described above, except for the bed (M140/M190/M303).
+ */
+ #define WATCH_BED_TEMP_PERIOD 60 // Seconds
+ #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+#if ENABLED(PIDTEMP)
+ // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
+ // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ #define PID_EXTRUSION_SCALING
+ #if ENABLED(PID_EXTRUSION_SCALING)
+ #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
+ #define LPQ_MAX_LEN 50
+ #endif
+#endif
+
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by executing M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
+#define AUTOTEMP
+#if ENABLED(AUTOTEMP)
+ #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+// Show extra position information in M114
+#define M114_DETAIL
+
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
+/**
+ * High Temperature Thermistor Support
+ *
+ * Thermistors able to support high temperature tend to have a hard time getting
+ * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
+ * will probably be caught when the heating element first turns on during the
+ * preheating process, which will trigger a min_temp_error as a safety measure
+ * and force stop everything.
+ * To circumvent this limitation, we allow for a preheat time (during which,
+ * min_temp_error won't be triggered) and add a min_temp buffer to handle
+ * aberrant readings.
+ *
+ * If you want to enable this feature for your hotend thermistor(s)
+ * uncomment and set values > 0 in the constants below
+ */
+
+// The number of consecutive low temperature errors that can occur
+// before a min_temp_error is triggered. (Shouldn't be more than 10.)
+//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
+
+// The number of milliseconds a hotend will preheat before starting to check
+// the temperature. This value should NOT be set to the time it takes the
+// hot end to reach the target temperature, but the time it takes to reach
+// the minimum temperature your thermistor can read. The lower the better/safer.
+// This shouldn't need to be more than 30 seconds (30000)
+//#define MILLISECONDS_PREHEAT_TIME 0
+
+// @section extruder
+
+// Extruder runout prevention.
+// If the machine is idle and the temperature over MINTEMP
+// then extrude some filament every couple of SECONDS.
+//#define EXTRUDER_RUNOUT_PREVENT
+#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
+ #define EXTRUDER_RUNOUT_MINTEMP 190
+ #define EXTRUDER_RUNOUT_SECONDS 30
+ #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
+ #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
+#endif
+
+// @section temperature
+
+// Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
+// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN 1.0
+#define TEMP_SENSOR_AD8495_OFFSET 0.0
+#define TEMP_SENSOR_AD8495_GAIN 1.0
+
+/**
+ * Controller Fan
+ * To cool down the stepper drivers and MOSFETs.
+ *
+ * The fan will turn on automatically whenever any stepper is enabled
+ * and turn off after a set period after all steppers are turned off.
+ */
+//#define USE_CONTROLLER_FAN
+#if ENABLED(USE_CONTROLLER_FAN)
+ //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
+ #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
+ #define CONTROLLERFAN_SPEED 255 // 255 == full speed
+#endif
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds. This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+#define FAN_KICKSTART_TIME 100
+
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
+#define FAN_MIN_PWM 64
+//#define FAN_MAX_PWM 128
+
+// @section extruder
+
+/**
+ * Extruder cooling fans
+ *
+ * Extruder auto fans automatically turn on when their extruders'
+ * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
+ *
+ * Your board's pins file specifies the recommended pins. Override those here
+ * or set to -1 to disable completely.
+ *
+ * Multiple extruders can be assigned to the same pin in which case
+ * the fan will turn on when any selected extruder is above the threshold.
+ */
+#define E0_AUTO_FAN_PIN -1
+#define E1_AUTO_FAN_PIN -1
+#define E2_AUTO_FAN_PIN -1
+#define E3_AUTO_FAN_PIN -1
+#define E4_AUTO_FAN_PIN -1
+#define CHAMBER_AUTO_FAN_PIN -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
+
+/**
+ * Part-Cooling Fan Multiplexer
+ *
+ * This feature allows you to digitally multiplex the fan output.
+ * The multiplexer is automatically switched at tool-change.
+ * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
+ */
+#define FANMUX0_PIN -1
+#define FANMUX1_PIN -1
+#define FANMUX2_PIN -1
+
+/**
+ * M355 Case Light on-off / brightness
+ */
+#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+//#define CASE_LIGHT_PIN 8 // Now set in appropriate pins file
+ #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
+ #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
+ #ifdef ROXYs_TRex
+ #define CASE_LIGHT_DEFAULT_BRIGHTNESS 25 // Set default power-up brightness (0-255, requires PWM pin)
+ #else
+ #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255 // Set default power-up brightness (0-255, requires PWM pin)
+ #endif
+ #define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
+ //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
+ #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
+ #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
+ #endif
+#endif
+
+//===========================================================================
+//============================ Mechanical Settings ==========================
+//===========================================================================
+
+// @section homing
+
+// If you want endstops to stay on (by default) even when not homing
+// enable this option. Override at any time with M120, M121.
+//#define ENDSTOPS_ALWAYS_ON_DEFAULT
+
+// @section extras
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+/**
+ * Dual Steppers / Dual Endstops
+ *
+ * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
+ *
+ * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
+ * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
+ * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
+ * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
+ *
+ * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
+ * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
+ * in X2. Dual endstop offsets can be set at runtime with 'M666 X<offset> Y<offset> Z<offset>'.
+ */
+
+//#define X_DUAL_STEPPER_DRIVERS
+#if ENABLED(X_DUAL_STEPPER_DRIVERS)
+ #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions
+ //#define X_DUAL_ENDSTOPS
+ #if ENABLED(X_DUAL_ENDSTOPS)
+ #define X2_USE_ENDSTOP _XMAX_
+ #define X_DUAL_ENDSTOPS_ADJUSTMENT 0
+ #endif
+#endif
+
+//#define Y_DUAL_STEPPER_DRIVERS
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+ #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions
+ //#define Y_DUAL_ENDSTOPS
+ #if ENABLED(Y_DUAL_ENDSTOPS)
+ #define Y2_USE_ENDSTOP _YMAX_
+ #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0
+ #endif
+#endif
+
+//#define Z_DUAL_STEPPER_DRIVERS
+#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
+ //#define Z_DUAL_ENDSTOPS
+ #if ENABLED(Z_DUAL_ENDSTOPS)
+ #define Z2_USE_ENDSTOP _XMAX_
+ #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0
+ #endif
+#endif
+
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
+#define DUAL_X_CARRIAGE
+#if ENABLED(DUAL_X_CARRIAGE)
+ // Configuration for second X-carriage
+ // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+ // the second x-carriage always homes to the maximum endstop.
+ #define X1_MIN_POS X_MIN_POS // set minimum to ensure first x-carriage doesn't hit the parked second X-carriage
+ #define X1_MAX_POS (X_BED_SIZE) // set maximum to ensure first x-carriage doesn't hit the parked second X-carriage
+ #define X2_MIN_POS 0 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+ #define X2_MAX_POS (442-4.0) // set maximum to the distance between toolheads when both heads are homed
+ #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
+ #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+ // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
+ // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+ // without modifying the firmware (through the "M218 T1 X???" command).
+ // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+ // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
+ // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+ // as long as it supports dual x-carriages. (M605 S0)
+ // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+ // that additional slicer support is not required. (M605 S1)
+ // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
+ // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+ // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+ // Mode 3 (DXC_SYMMETRIC_DUPLICATION_MODE) : Symmetric Duplication mode. The firmware will perform similarly to DXC_DUPLICATION_MODE except in a mirror
+ // image of the first x-carriage. ie. If you are printing a right hand shoe on the 1st extruder, you will
+ // get a left hand shoe on the 2nd extruder.
+
+ // This is the default power-up mode which can be later using M605.
+ #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
+
+ // Default settings in "Auto-park Mode"
+ #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
+ #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
+
+ // Default x offset in duplication mode (typically set to half print bed width)
+ #define DEFAULT_DUPLICATION_X_OFFSET 200
+
+#endif // DUAL_X_CARRIAGE
+
+// Activate a solenoid on the active extruder with M380. Disable all with M381.
+// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
+//#define EXT_SOLENOID
+
+// @section homing
+
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
+#define X_HOME_BUMP_MM 5
+#define Y_HOME_BUMP_MM 5
+#define Z_HOME_BUMP_MM 2
+#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
+
+// When G28 is called, this option will make Y home before X
+//#define HOME_Y_BEFORE_X
+
+// Enable this if X or Y can't home without homing the other axis first.
+//#define CODEPENDENT_XY_HOMING
+
+// @section machine
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+// Allow duplication mode with a basic dual-nozzle extruder
+//#define DUAL_NOZZLE_DUPLICATION_MODE
+
+// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+// Default stepper release if idle. Set to 0 to deactivate.
+// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
+// Time can be set by M18 and M84.
+#define DEFAULT_STEPPER_DEACTIVE_TIME 600
+#define DISABLE_INACTIVE_X true
+#define DISABLE_INACTIVE_Y true
+#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_E true
+
+#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE 0.0
+
+//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
+
+// @section lcd
+
+#if ENABLED(ULTIPANEL)
+ #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+ #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
+#endif
+
+// @section extras
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME 20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT 15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+
+//
+// Use Junction Deviation instead of traditional Jerk Limiting
+//
+//#define JUNCTION_DEVIATION
+#if ENABLED(JUNCTION_DEVIATION)
+ #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge
+#endif
+
+/**
+ * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
+ * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
+ * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
+ * lowest stepping frequencies.
+ */
+//#define ADAPTIVE_STEP_SMOOTHING
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
+
+/**
+ * @section stepper motor current
+ *
+ * Some boards have a means of setting the stepper motor current via firmware.
+ *
+ * The power on motor currents are set by:
+ * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
+ * known compatible chips: A4982
+ * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
+ * known compatible chips: AD5206
+ * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
+ * known compatible chips: MCP4728
+ * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
+ * known compatible chips: MCP4451, MCP4018
+ *
+ * Motor currents can also be set by M907 - M910 and by the LCD.
+ * M907 - applies to all.
+ * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
+ * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
+ */
+//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
+//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
+
+// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro)
+//#define DIGIPOT_I2C
+#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A)
+ /**
+ * Common slave addresses:
+ *
+ * A (A shifted) B (B shifted) IC
+ * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
+ * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
+ * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
+ */
+ #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT
+ #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT
+#endif
+
+//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
+#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5
+// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
+// These correspond to the physical drivers, so be mindful if the order is changed.
+#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
+#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
+
+//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
+// @section lcd
+
+// Include a page of printer information in the LCD Main Menu
+#define LCD_INFO_MENU
+
+// Scroll a longer status message into view
+#define STATUS_MESSAGE_SCROLLING
+
+// On the Info Screen, display XY with one decimal place when possible
+#define LCD_DECIMAL_SMALL_XY
+
+// The timeout (in ms) to return to the status screen from sub-menus
+#define LCD_TIMEOUT_TO_STATUS 15000
+
+// Add an 'M73' G-code to set the current percentage
+#define LCD_SET_PROGRESS_MANUALLY
+
+#if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY)
+ //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
+ #if ENABLED(LCD_PROGRESS_BAR)
+ #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
+ #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
+ #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
+ //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
+ //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
+ #endif
+#endif // SDSUPPORT || LCD_SET_PROGRESS_MANUALLY
+
+/**
+ * LED Control Menu
+ * Enable this feature to add LED Control to the LCD menu
+ */
+//#define LED_CONTROL_MENU
+#if ENABLED(LED_CONTROL_MENU)
+ #define LED_COLOR_PRESETS // Enable the Preset Color menu option
+ #if ENABLED(LED_COLOR_PRESETS)
+ #define LED_USER_PRESET_RED 255 // User defined RED value
+ #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
+ #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
+ #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
+ #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
+ //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
+ #endif
+#endif // LED_CONTROL_MENU
+
+#if ENABLED(SDSUPPORT)
+
+ // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
+ // around this by connecting a push button or single throw switch to the pin defined
+ // as SD_DETECT_PIN in your board's pins definitions.
+ // This setting should be disabled unless you are using a push button, pulling the pin to ground.
+ // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
+ #define SD_DETECT_INVERTED
+
+ #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
+ #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+ // Reverse SD sort to show "more recent" files first, according to the card's FAT.
+ // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
+ #define SDCARD_RATHERRECENTFIRST
+
+ // Add an option in the menu to run all auto#.g files
+ //#define MENU_ADDAUTOSTART
+
+ /**
+ * Continue after Power-Loss (Creality3D)
+ *
+ * Store the current state to the SD Card at the start of each layer
+ * during SD printing. If the recovery file is found at boot time, present
+ * an option on the LCD screen to continue the print from the last-known
+ * point in the file.
+ */
+ //#define POWER_LOSS_RECOVERY
+ #if ENABLED(POWER_LOSS_RECOVERY)
+ //#define POWER_LOSS_PIN 44 // Pin to detect power loss
+ //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
+ #endif
+
+ /**
+ * Sort SD file listings in alphabetical order.
+ *
+ * With this option enabled, items on SD cards will be sorted
+ * by name for easier navigation.
+ *
+ * By default...
+ *
+ * - Use the slowest -but safest- method for sorting.
+ * - Folders are sorted to the top.
+ * - The sort key is statically allocated.
+ * - No added G-code (M34) support.
+ * - 40 item sorting limit. (Items after the first 40 are unsorted.)
+ *
+ * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
+ * compiler to calculate the worst-case usage and throw an error if the SRAM
+ * limit is exceeded.
+ *
+ * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
+ * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
+ * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
+ * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
+ */
+ //#define SDCARD_SORT_ALPHA
+
+ // SD Card Sorting options
+ #if ENABLED(SDCARD_SORT_ALPHA)
+ #define SDSORT_LIMIT 20 // Maximum number of sorted items (10-256). Costs 27 bytes each.
+ #define FOLDER_SORTING -1 // -1=above 0=none 1=below
+ #define SDSORT_GCODE true // Allow turning sorting on/off with LCD and M34 g-code.
+ #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
+ #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
+ #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
+ #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
+ #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
+ // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
+ #endif
+
+ // This allows hosts to request long names for files and folders with M33
+ #define LONG_FILENAME_HOST_SUPPORT
+
+ // Enable this option to scroll long filenames in the SD card menu
+ #define SCROLL_LONG_FILENAMES
+
+ /**
+ * This option allows you to abort SD printing when any endstop is triggered.
+ * This feature must be enabled with "M540 S1" or from the LCD menu.
+ * To have any effect, endstops must be enabled during SD printing.
+ */
+ //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+ /**
+ * This option makes it easier to print the same SD Card file again.
+ * On print completion the LCD Menu will open with the file selected.
+ * You can just click to start the print, or navigate elsewhere.
+ */
+ //#define SD_REPRINT_LAST_SELECTED_FILE
+
+ /**
+ * Auto-report SdCard status with M27 S<seconds>
+ */
+ #define AUTO_REPORT_SD_STATUS
+
+#endif // SDSUPPORT
+
+/**
+ * Additional options for Graphical Displays
+ *
+ * Use the optimizations here to improve printing performance,
+ * which can be adversely affected by graphical display drawing,
+ * especially when doing several short moves, and when printing
+ * on DELTA and SCARA machines.
+ *
+ * Some of these options may result in the display lagging behind
+ * controller events, as there is a trade-off between reliable
+ * printing performance versus fast display updates.
+ */
+#if ENABLED(DOGLCD)
+ // Show SD percentage next to the progress bar
+ //#define DOGM_SD_PERCENT
+
+ // Enable to save many cycles by drawing a hollow frame on the Info Screen
+ #define XYZ_HOLLOW_FRAME
+
+ // Enable to save many cycles by drawing a hollow frame on Menu Screens
+ #define MENU_HOLLOW_FRAME
+
+ // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ #define USE_BIG_EDIT_FONT
+
+ // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ //#define USE_SMALL_INFOFONT
+
+ // Enable this option and reduce the value to optimize screen updates.
+ // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
+ //#define DOGM_SPI_DELAY_US 5
+
+ // Swap the CW/CCW indicators in the graphics overlay
+ //#define OVERLAY_GFX_REVERSE
+
+ #if ENABLED(U8GLIB_ST7920)
+ /**
+ * ST7920-based LCDs can emulate a 16 x 4 character display using
+ * the ST7920 character-generator for very fast screen updates.
+ * Enable LIGHTWEIGHT_UI to use this special display mode.
+ *
+ * Since LIGHTWEIGHT_UI has limited space, the position and status
+ * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
+ * length of time to display the status message before clearing.
+ *
+ * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
+ * This will prevent position updates from being displayed.
+ */
+ //#define LIGHTWEIGHT_UI
+ #if ENABLED(LIGHTWEIGHT_UI)
+ #define STATUS_EXPIRE_SECONDS 20
+ #endif
+ #endif
+
+#endif // DOGLCD
+
+// @section safety
+
+// The hardware watchdog should reset the microcontroller disabling all outputs,
+// in case the firmware gets stuck and doesn't do temperature regulation.
+#define USE_WATCHDOG
+
+#if ENABLED(USE_WATCHDOG)
+ // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+ // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+ // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+ //#define WATCHDOG_RESET_MANUAL
+#endif
+
+// @section lcd
+
+/**
+ * Babystepping enables movement of the axes by tiny increments without changing
+ * the current position values. This feature is used primarily to adjust the Z
+ * axis in the first layer of a print in real-time.
+ *
+ * Warning: Does not respect endstops!
+ */
+#define BABYSTEPPING
+#if ENABLED(BABYSTEPPING)
+ //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
+ #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
+ #define BABYSTEP_MULTIPLICATOR 40 // Babysteps are very small. Increase for faster motion.
+//#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+ #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
+ #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
+ // Note: Extra time may be added to mitigate controller latency.
+//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+#endif
+
+// @section extruder
+
+/**
+ * Linear Pressure Control v1.5
+ *
+ * Assumption: advance [steps] = k * (delta velocity [steps/s])
+ * K=0 means advance disabled.
+ *
+ * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
+ *
+ * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
+ * Larger K values will be needed for flexible filament and greater distances.
+ * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
+ * print acceleration will be reduced during the affected moves to keep within the limit.
+ *
+ * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
+ * Mention @Sebastianv650 on GitHub to alert the author of any issues.
+ */
+//#define LIN_ADVANCE
+#if ENABLED(LIN_ADVANCE)
+ #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
+ //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
+#endif
+
+// @section leveling
+
+#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
+ // Override the mesh area if the automatic (max) area is too large
+ //#define MESH_MIN_X 4
+ //#define MESH_MIN_Y MESH_INSET
+ //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
+ //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
+#endif
+
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+ #define G29_MAX_RETRIES 3
+ #define G29_HALT_ON_FAILURE
+ /**
+ * Specify the GCODE commands that will be executed when leveling succeeds,
+ * between attempts, and after the maximum number of retries have been tried.
+ */
+ #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+ #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+ #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+ /**
+ * Specify an action command to send to the host on a recovery attempt or failure.
+ * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+ * The host must be configured to handle the action command.
+ */
+ #define G29_ACTION_ON_RECOVER "probe_rewipe"
+ #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
+// @section extras
+
+//
+// G2/G3 Arc Support
+//
+#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+ #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
+ #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
+ //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
+ //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
+
+// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
+//#define BEZIER_CURVE_SUPPORT
+
+// G38.2 and G38.3 Probe Target
+// Set MULTIPLE_PROBING if you want G38 to double touch
+//#define G38_PROBE_TARGET
+#if ENABLED(G38_PROBE_TARGET)
+ #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
+#endif
+
+// Moves (or segments) with fewer steps than this will be joined with the next move
+#define MIN_STEPS_PER_SEGMENT 6
+
+/**
+ * Minimum delay after setting the stepper DIR (in ns)
+ * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
+ * 20 : Minimum for TMC2xxx drivers
+ * 200 : Minimum for A4988 drivers
+ * 400 : Minimum for A5984 drivers
+ * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
+ * 650 : Minimum for DRV8825 drivers
+ * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
+ * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
+ *
+ * Override the default value based on the driver type set in Configuration.h.
+ */
+//#define MINIMUM_STEPPER_DIR_DELAY 650
+
+/**
+ * Minimum stepper driver pulse width (in µs)
+ * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ * 1 : Minimum for A4988, A5984, and LV8729 stepper drivers
+ * 2 : Minimum for DRV8825 stepper drivers
+ * 3 : Minimum for TB6600 stepper drivers
+ * 30 : Minimum for TB6560 stepper drivers
+ *
+ * Override the default value based on the driver type set in Configuration.h.
+ */
+//#define MINIMUM_STEPPER_PULSE 2
+
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ * 500000 : Maximum for A4988 stepper driver
+ * 400000 : Maximum for TMC2xxx stepper drivers
+ * 250000 : Maximum for DRV8825 stepper driver
+ * 150000 : Maximum for TB6600 stepper driver
+ * 130000 : Maximum for LV8729 stepper driver
+ * 15000 : Maximum for TB6560 stepper driver
+ *
+ * Override the default value based on the driver type set in Configuration.h.
+ */
+//#define MAXIMUM_STEPPER_RATE 250000
+
+// @section temperature
+
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
+//===========================================================================
+//================================= Buffers =================================
+//===========================================================================
+
+// @section hidden
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
+#if ENABLED(SDSUPPORT)
+ #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+ #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+// @section serial
+
+// The ASCII buffer for serial input
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 4
+
+// Transmission to Host Buffer Size
+// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
+// To buffer a simple "ok" you need 4 bytes.
+// For ADVANCED_OK (M105) you need 32 bytes.
+// For debug-echo: 128 bytes for the optimal speed.
+// Other output doesn't need to be that speedy.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
+#define TX_BUFFER_SIZE 0
+
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+ // Enable to have the controller send XON/XOFF control characters to
+ // the host to signal the RX buffer is becoming full.
+ //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+ // Enable this option to collect and display the maximum
+ // RX queue usage after transferring a file to SD.
+ //#define SERIAL_STATS_MAX_RX_QUEUED
+
+ // Enable this option to collect and display the number
+ // of dropped bytes after a file transfer to SD.
+ //#define SERIAL_STATS_DROPPED_RX
+#endif
+
+// Enable an emergency-command parser to intercept certain commands as they
+// enter the serial receive buffer, so they cannot be blocked.
+// Currently handles M108, M112, M410
+// Does not work on boards using AT90USB (USBCON) processors!
+//#define EMERGENCY_PARSER
+
+// Bad Serial-connections can miss a received command by sending an 'ok'
+// Therefore some clients abort after 30 seconds in a timeout.
+// Some other clients start sending commands while receiving a 'wait'.
+// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
+//#define NO_TIMEOUTS 1000 // Milliseconds
+
+// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
+//#define ADVANCED_OK
+
+// @section extras
+
+/**
+ * Firmware-based and LCD-controlled retract
+ *
+ * Add G10 / G11 commands for automatic firmware-based retract / recover.
+ * Use M207 and M208 to define parameters for retract / recover.
+ *
+ * Use M209 to enable or disable auto-retract.
+ * With auto-retract enabled, all G1 E moves within the set range
+ * will be converted to firmware-based retract/recover moves.
+ *
+ * Be sure to turn off auto-retract during filament change.
+ *
+ * Note that M207 / M208 / M209 settings are saved to EEPROM.
+ *
+ */
+//#define FWRETRACT // ONLY PARTIALLY TESTED
+#if ENABLED(FWRETRACT)
+ #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
+ #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
+ #define RETRACT_LENGTH 3 // Default retract length (positive mm)
+ #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
+ #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
+ #define RETRACT_ZLIFT 0 // Default retract Z-lift
+ #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
+ #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
+ #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
+ #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s)
+#endif
+
+/**
+ * Extra Fan Speed
+ * Adds a secondary fan speed for each print-cooling fan.
+ * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
+ * 'M106 P<fan> T2' : Use the set secondary speed
+ * 'M106 P<fan> T1' : Restore the previous fan speed
+ */
+#define EXTRA_FAN_SPEED
+
+/**
+ * Advanced Pause
+ * Experimental feature for filament change support and for parking the nozzle when paused.
+ * Adds the GCode M600 for initiating filament change.
+ * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
+ *
+ * Requires an LCD display.
+ * Requires NOZZLE_PARK_FEATURE.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+#define ADVANCED_PAUSE_FEATURE
+#if ENABLED(ADVANCED_PAUSE_FEATURE)
+ #define PAUSE_PARK_RETRACT_FEEDRATE 7 // (mm/s) Initial retract feedrate.
+ #define PAUSE_PARK_RETRACT_LENGTH 1 // (mm) Initial retract.
+ // This short retract is done immediately, before parking the nozzle.
+ #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 15 // (mm/s) Unload filament feedrate. This can be pretty fast.
+ #define FILAMENT_CHANGE_UNLOAD_ACCEL 15 // (mm/s^2) Lower acceleration may allow a faster feedrate.
+ #define FILAMENT_CHANGE_UNLOAD_LENGTH 85 // (mm) The length of filament for a complete unload.
+ // For Bowden, the full length of the tube and nozzle.
+ // For direct drive, the full length of the nozzle.
+ // Set to 0 for manual unloading.
+ #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 3 // (mm/s) Slow move when starting load.
+ #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 1 // (mm) Slow length, to allow time to insert material.
+ // 0 to disable start loading and skip to fast load only
+ #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 4 // (mm/s) Load filament feedrate. This can be pretty fast.
+ #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 15 // (mm/s^2) Lower acceleration may allow a faster feedrate.
+ #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 60 // (mm) Load length of filament, from extruder gear to nozzle.
+ // For Bowden, the full length of the tube and nozzle.
+ // For direct drive, the full length of the nozzle.
+ //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
+ #define ADVANCED_PAUSE_PURGE_FEEDRATE 2 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
+ #define ADVANCED_PAUSE_PURGE_LENGTH 20 // (mm) Length to extrude after loading.
+ // Set to 0 for manual extrusion.
+ // Filament can be extruded repeatedly from the Filament Change menu
+ // until extrusion is consistent, and to purge old filament.
+
+ // Filament Unload does a Retract, Delay, and Purge first:
+ #define FILAMENT_UNLOAD_RETRACT_LENGTH 0 // (mm) Unload initial retract length.
+ #define FILAMENT_UNLOAD_DELAY 500 // (ms) Delay for the filament to cool after retract.
+ #define FILAMENT_UNLOAD_PURGE_LENGTH 0 // (mm) An unretract is done, then this length is purged.
+
+ #define PAUSE_PARK_NOZZLE_TIMEOUT (3*60) // (seconds) Time limit before the nozzle is turned off for safety.
+ #define FILAMENT_CHANGE_ALERT_BEEPS 3 // Number of alert beeps to play when a response is needed.
+ #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
+
+ #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
+ #define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
+
+ #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+ #define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+#endif
+
+// @section tmc
+
+/**
+ * TMC26X Stepper Driver options
+ *
+ * The TMC26XStepper library is required for this stepper driver.
+ * https://github.com/trinamic/TMC26XStepper
+ */
+#if HAS_DRIVER(TMC26X)
+
+ #define X_MAX_CURRENT 1000 // in mA
+ #define X_SENSE_RESISTOR 91 // in mOhms
+ #define X_MICROSTEPS 16 // number of microsteps
+
+ #define X2_MAX_CURRENT 1000
+ #define X2_SENSE_RESISTOR 91
+ #define X2_MICROSTEPS 16
+
+ #define Y_MAX_CURRENT 1000
+ #define Y_SENSE_RESISTOR 91
+ #define Y_MICROSTEPS 16
+
+ #define Y2_MAX_CURRENT 1000
+ #define Y2_SENSE_RESISTOR 91
+ #define Y2_MICROSTEPS 16
+
+ #define Z_MAX_CURRENT 1000
+ #define Z_SENSE_RESISTOR 91
+ #define Z_MICROSTEPS 16
+
+ #define Z2_MAX_CURRENT 1000
+ #define Z2_SENSE_RESISTOR 91
+ #define Z2_MICROSTEPS 16
+
+ #define E0_MAX_CURRENT 1000
+ #define E0_SENSE_RESISTOR 91
+ #define E0_MICROSTEPS 16
+
+ #define E1_MAX_CURRENT 1000
+ #define E1_SENSE_RESISTOR 91
+ #define E1_MICROSTEPS 16
+
+ #define E2_MAX_CURRENT 1000
+ #define E2_SENSE_RESISTOR 91
+ #define E2_MICROSTEPS 16
+
+ #define E3_MAX_CURRENT 1000
+ #define E3_SENSE_RESISTOR 91
+ #define E3_MICROSTEPS 16
+
+ #define E4_MAX_CURRENT 1000
+ #define E4_SENSE_RESISTOR 91
+ #define E4_MICROSTEPS 16
+
+#endif // TMC26X
+
+// @section tmc_smart
+
+/**
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
+ * the hardware SPI interface on your board and define the required CS pins
+ * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
+ *
+ * The TMC2130Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * To use TMC2208 stepper UART-configurable stepper drivers
+ * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ * To use the reading capabilities, also connect #_SERIAL_RX_PIN
+ * to PDN_UART without a resistor.
+ * The drivers can also be used with hardware serial.
+ *
+ * The TMC2208Stepper library is required for this stepper driver.
+ * https://github.com/teemuatlut/TMC2208Stepper
+ */
+#if HAS_TRINAMIC
+
+ #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
+ #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
+ #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
+
+ #define X_CURRENT 800 // rms current in mA. Multiply by 1.41 for peak current.
+ #define X_MICROSTEPS 16 // 0..256
+
+ #define Y_CURRENT 800
+ #define Y_MICROSTEPS 16
+
+ #define Z_CURRENT 800
+ #define Z_MICROSTEPS 16
+
+ #define X2_CURRENT 800
+ #define X2_MICROSTEPS 16
+
+ #define Y2_CURRENT 800
+ #define Y2_MICROSTEPS 16
+
+ #define Z2_CURRENT 800
+ #define Z2_MICROSTEPS 16
+
+ #define E0_CURRENT 800
+ #define E0_MICROSTEPS 16
+
+ #define E1_CURRENT 800
+ #define E1_MICROSTEPS 16
+
+ #define E2_CURRENT 800
+ #define E2_MICROSTEPS 16
+
+ #define E3_CURRENT 800
+ #define E3_MICROSTEPS 16
+
+ #define E4_CURRENT 800
+ #define E4_MICROSTEPS 16
+
+ /**
+ * Use software SPI for TMC2130.
+ * The default SW SPI pins are defined the respective pins files,
+ * but you can override or define them here.
+ */
+ //#define TMC_USE_SW_SPI
+ //#define TMC_SW_MOSI -1
+ //#define TMC_SW_MISO -1
+ //#define TMC_SW_SCK -1
+
+ /**
+ * Use Trinamic's ultra quiet stepping mode.
+ * When disabled, Marlin will use spreadCycle stepping mode.
+ */
+ #define STEALTHCHOP
+
+ /**
+ * Monitor Trinamic TMC2130 and TMC2208 drivers for error conditions,
+ * like overtemperature and short to ground. TMC2208 requires hardware serial.
+ * In the case of overtemperature Marlin can decrease the driver current until error condition clears.
+ * Other detected conditions can be used to stop the current print.
+ * Relevant g-codes:
+ * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
+ * M911 - Report stepper driver overtemperature pre-warn condition.
+ * M912 - Clear stepper driver overtemperature pre-warn condition flag.
+ * M122 S0/1 - Report driver parameters (Requires TMC_DEBUG)
+ */
+ //#define MONITOR_DRIVER_STATUS
+
+ #if ENABLED(MONITOR_DRIVER_STATUS)
+ #define CURRENT_STEP_DOWN 50 // [mA]
+ #define REPORT_CURRENT_CHANGE
+ #define STOP_ON_ERROR
+ #endif
+
+ /**
+ * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
+ * This mode allows for faster movements at the expense of higher noise levels.
+ * STEALTHCHOP needs to be enabled.
+ * M913 X/Y/Z/E to live tune the setting
+ */
+ //#define HYBRID_THRESHOLD
+
+ #define X_HYBRID_THRESHOLD 100 // [mm/s]
+ #define X2_HYBRID_THRESHOLD 100
+ #define Y_HYBRID_THRESHOLD 100
+ #define Y2_HYBRID_THRESHOLD 100
+ #define Z_HYBRID_THRESHOLD 3
+ #define Z2_HYBRID_THRESHOLD 3
+ #define E0_HYBRID_THRESHOLD 30
+ #define E1_HYBRID_THRESHOLD 30
+ #define E2_HYBRID_THRESHOLD 30
+ #define E3_HYBRID_THRESHOLD 30
+ #define E4_HYBRID_THRESHOLD 30
+
+ /**
+ * Use stallGuard2 to sense an obstacle and trigger an endstop.
+ * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
+ * X, Y, and Z homing will always be done in spreadCycle mode.
+ *
+ * X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
+ * Higher values make the system LESS sensitive.
+ * Lower value make the system MORE sensitive.
+ * Too low values can lead to false positives, while too high values will collide the axis without triggering.
+ * It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
+ * M914 X/Y/Z to live tune the setting
+ */
+ //#define SENSORLESS_HOMING // TMC2130 only
+
+ #if ENABLED(SENSORLESS_HOMING)
+ #define X_HOMING_SENSITIVITY 8
+ #define Y_HOMING_SENSITIVITY 8
+ #define Z_HOMING_SENSITIVITY 8
+ #endif
+
+ /**
+ * Enable M122 debugging command for TMC stepper drivers.
+ * M122 S0/1 will enable continous reporting.
+ */
+ //#define TMC_DEBUG
+
+ /**
+ * M915 Z Axis Calibration
+ *
+ * - Adjust Z stepper current,
+ * - Drive the Z axis to its physical maximum, and
+ * - Home Z to account for the lost steps.
+ *
+ * Use M915 Snn to specify the current.
+ * Use M925 Znn to add extra Z height to Z_MAX_POS.
+ */
+ //#define TMC_Z_CALIBRATION
+ #if ENABLED(TMC_Z_CALIBRATION)
+ #define CALIBRATION_CURRENT 250
+ #define CALIBRATION_EXTRA_HEIGHT 10
+ #endif
+
+ /**
+ * You can set your own advanced settings by filling in predefined functions.
+ * A list of available functions can be found on the library github page
+ * https://github.com/teemuatlut/TMC2130Stepper
+ * https://github.com/teemuatlut/TMC2208Stepper
+ *
+ * Example:
+ * #define TMC_ADV() { \
+ * stepperX.diag0_temp_prewarn(1); \
+ * stepperY.interpolate(0); \
+ * }
+ */
+ #define TMC_ADV() { }
+
+#endif // TMC2130 || TMC2208
+
+// @section L6470
+
+/**
+ * L6470 Stepper Driver options
+ *
+ * The Arduino-L6470 library is required for this stepper driver.
+ * https://github.com/ameyer/Arduino-L6470
+ */
+#if HAS_DRIVER(L6470)
+
+ #define X_MICROSTEPS 16 // number of microsteps
+ #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
+ #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
+
+ #define X2_MICROSTEPS 16
+ #define X2_OVERCURRENT 2000
+ #define X2_STALLCURRENT 1500
+
+ #define Y_MICROSTEPS 16
+ #define Y_OVERCURRENT 2000
+ #define Y_STALLCURRENT 1500
+
+ #define Y2_MICROSTEPS 16
+ #define Y2_OVERCURRENT 2000
+ #define Y2_STALLCURRENT 1500
+
+ #define Z_MICROSTEPS 16
+ #define Z_OVERCURRENT 2000
+ #define Z_STALLCURRENT 1500
+
+ #define Z2_MICROSTEPS 16
+ #define Z2_OVERCURRENT 2000
+ #define Z2_STALLCURRENT 1500
+
+ #define E0_MICROSTEPS 16
+ #define E0_OVERCURRENT 2000
+ #define E0_STALLCURRENT 1500
+
+ #define E1_MICROSTEPS 16
+ #define E1_OVERCURRENT 2000
+ #define E1_STALLCURRENT 1500
+
+ #define E2_MICROSTEPS 16
+ #define E2_OVERCURRENT 2000
+ #define E2_STALLCURRENT 1500
+
+ #define E3_MICROSTEPS 16
+ #define E3_OVERCURRENT 2000
+ #define E3_STALLCURRENT 1500
+
+ #define E4_MICROSTEPS 16
+ #define E4_OVERCURRENT 2000
+ #define E4_STALLCURRENT 1500
+
+#endif // L6470
+
+/**
+ * TWI/I2C BUS
+ *
+ * This feature is an EXPERIMENTAL feature so it shall not be used on production
+ * machines. Enabling this will allow you to send and receive I2C data from slave
+ * devices on the bus.
+ *
+ * ; Example #1
+ * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
+ * ; It uses multiple M260 commands with one B<base 10> arg
+ * M260 A99 ; Target slave address
+ * M260 B77 ; M
+ * M260 B97 ; a
+ * M260 B114 ; r
+ * M260 B108 ; l
+ * M260 B105 ; i
+ * M260 B110 ; n
+ * M260 S1 ; Send the current buffer
+ *
+ * ; Example #2
+ * ; Request 6 bytes from slave device with address 0x63 (99)
+ * M261 A99 B5
+ *
+ * ; Example #3
+ * ; Example serial output of a M261 request
+ * echo:i2c-reply: from:99 bytes:5 data:hello
+ */
+
+// @section i2cbus
+
+//#define EXPERIMENTAL_I2CBUS
+#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
+
+// @section extras
+
+/**
+ * Spindle & Laser control
+ *
+ * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
+ * to set spindle speed, spindle direction, and laser power.
+ *
+ * SuperPid is a router/spindle speed controller used in the CNC milling community.
+ * Marlin can be used to turn the spindle on and off. It can also be used to set
+ * the spindle speed from 5,000 to 30,000 RPM.
+ *
+ * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
+ * hardware PWM pin for the speed control and a pin for the rotation direction.
+ *
+ * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
+ */
+//#define SPINDLE_LASER_ENABLE
+#if ENABLED(SPINDLE_LASER_ENABLE)
+
+ #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
+ #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
+ #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
+ #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
+ #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
+ #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
+ #define SPINDLE_INVERT_DIR false
+ #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
+
+ /**
+ * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
+ *
+ * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
+ * where PWM duty cycle varies from 0 to 255
+ *
+ * set the following for your controller (ALL MUST BE SET)
+ */
+
+ #define SPEED_POWER_SLOPE 118.4
+ #define SPEED_POWER_INTERCEPT 0
+ #define SPEED_POWER_MIN 5000
+ #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
+
+ //#define SPEED_POWER_SLOPE 0.3922
+ //#define SPEED_POWER_INTERCEPT 0
+ //#define SPEED_POWER_MIN 10
+ //#define SPEED_POWER_MAX 100 // 0-100%
+#endif
+
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
+ * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
+ #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
+
+ #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
+ #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+ #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+ // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+ //#define FILAMENT_LCD_DISPLAY
+#endif
+
+/**
+ * CNC Coordinate Systems
+ *
+ * Enables G53 and G54-G59.3 commands to select coordinate systems
+ * and G92.1 to reset the workspace to native machine space.
+ */
+//#define CNC_COORDINATE_SYSTEMS
+
+/**
+ * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
+ */
+#define PINS_DEBUGGING
+
+/**
+ * Auto-report temperatures with M155 S<seconds>
+ */
+#define AUTO_REPORT_TEMPERATURES
+
+/**
+ * Include capabilities in M115 output
+ */
+#define EXTENDED_CAPABILITIES_REPORT
+
+/**
+ * Disable all Volumetric extrusion options
+ */
+//#define NO_VOLUMETRICS
+
+#if DISABLED(NO_VOLUMETRICS)
+ /**
+ * Volumetric extrusion default state
+ * Activate to make volumetric extrusion the default method,
+ * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
+ *
+ * M200 D0 to disable, M200 Dn to set a new diameter.
+ */
+ //#define VOLUMETRIC_DEFAULT_ON
+#endif
+
+/**
+ * Enable this option for a leaner build of Marlin that removes all
+ * workspace offsets, simplifying coordinate transformations, leveling, etc.
+ *
+ * - M206 and M428 are disabled.
+ * - G92 will revert to its behavior from Marlin 1.0.
+ */
+//#define NO_WORKSPACE_OFFSETS
+
+/**
+ * Set the number of proportional font spaces required to fill up a typical character space.
+ * This can help to better align the output of commands like `G29 O` Mesh Output.
+ *
+ * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
+ * Otherwise, adjust according to your client and font.
+ */
+#define PROPORTIONAL_FONT_RATIO 1.5
+
+/**
+ * Spend 28 bytes of SRAM to optimize the GCode parser
+ */
+#define FASTER_GCODE_PARSER
+
+/**
+ * User-defined menu items that execute custom GCode
+ */
+//#define CUSTOM_USER_MENUS
+#if ENABLED(CUSTOM_USER_MENUS)
+//#define USER_SCRIPT_AUDIBLE_FEEDBACK
+ #define USER_SCRIPT_RETURN // Return to status screen after a script
+
+ #define USER_DESC_1 "User cmd 1"
+ #define USER_GCODE_1 "G28 X \n"
+
+ #define USER_DESC_2 "User cmd 2"
+ #define USER_GCODE_2 "G28 \nG1 X100 \n"
+
+ #define USER_DESC_3 "User cmd 3"
+ #define USER_GCODE_3 "M48 \n"
+
+ #define USER_DESC_4 "User cmd 4"
+ #define USER_GCODE_4 "M114 \n"
+#endif
+
+/**
+ * Specify an action command to send to the host when the printer is killed.
+ * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'.
+ * The host must be configured to handle the action command.
+ */
+//#define ACTION_ON_KILL "poweroff"
+
+/**
+ * Specify an action command to send to the host on pause and resume.
+ * Will be sent in the form '//action:ACTION_ON_PAUSE', e.g. '//action:pause'.
+ * The host must be configured to handle the action command.
+ */
+#define ACTION_ON_PAUSE "pause"
+#define ACTION_ON_RESUME "resume"
+
+//===========================================================================
+//====================== I2C Position Encoder Settings ======================
+//===========================================================================
+
+/**
+ * I2C position encoders for closed loop control.
+ * Developed by Chris Barr at Aus3D.
+ *
+ * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
+ * Github: https://github.com/Aus3D/MagneticEncoder
+ *
+ * Supplier: http://aus3d.com.au/magnetic-encoder-module
+ * Alternative Supplier: http://reliabuild3d.com/
+ *
+ * Reilabuild encoders have been modified to improve reliability.
+ */
+
+//#define I2C_POSITION_ENCODERS
+#if ENABLED(I2C_POSITION_ENCODERS)
+
+ #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
+ // encoders supported currently.
+
+ #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
+ #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
+ #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
+ // I2CPE_ENC_TYPE_ROTARY.
+ #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
+ // 1mm poles. For linear encoders this is ticks / mm,
+ // for rotary encoders this is ticks / revolution.
+ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
+ // steps per full revolution (motor steps/rev * microstepping)
+ //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
+ #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
+ #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
+ // printer will attempt to correct the error; errors
+ // smaller than this are ignored to minimize effects of
+ // measurement noise / latency (filter).
+
+ #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
+ #define I2CPE_ENC_2_AXIS Y_AXIS
+ #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_ENC_2_TICKS_UNIT 2048
+ //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
+ //#define I2CPE_ENC_2_INVERT
+ #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
+ #define I2CPE_ENC_2_EC_THRESH 0.10
+
+ #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
+ #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
+
+ #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
+ #define I2CPE_ENC_4_AXIS E_AXIS
+
+ #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
+ #define I2CPE_ENC_5_AXIS E_AXIS
+
+ // Default settings for encoders which are enabled, but without settings configured above.
+ #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_DEF_ENC_TICKS_UNIT 2048
+ #define I2CPE_DEF_TICKS_REV (16 * 200)
+ #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
+ #define I2CPE_DEF_EC_THRESH 0.1
+
+ //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
+ // axis after which the printer will abort. Comment out to
+ // disable abort behaviour.
+
+ #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
+ // for this amount of time (in ms) before the encoder
+ // is trusted again.
+
+ /**
+ * Position is checked every time a new command is executed from the buffer but during long moves,
+ * this setting determines the minimum update time between checks. A value of 100 works well with
+ * error rolling average when attempting to correct only for skips and not for vibration.
+ */
+ #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
+
+ // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+ #define I2CPE_ERR_ROLLING_AVERAGE
+
+#endif // I2C_POSITION_ENCODERS
+
+/**
+ * MAX7219 Debug Matrix
+ *
+ * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
+ * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
+ */
+
+#ifdef ROXYs_TRex
+ #define MAX7219_DEBUG
+#endif
+
+#if ENABLED(MAX7219_DEBUG)
+/*
+#define MAX7219_CLK_PIN 50 // Configuration of the 3 pins to control the display
+#define MAX7219_DIN_PIN 51 // on RUMBA (or Formbot) using the ICSP port is used
+#define MAX7219_LOAD_PIN 52 // This will affect your use of the SD Memory card */
+
+#define MAX7219_CLK_PIN 41 // Configuration of the 3 pins to control the display
+#define MAX7219_DIN_PIN 13 // 41 is LCD_Kill_Button, 13 is Arduino_LED, 37 is LCD_Beeper
+#define MAX7219_LOAD_PIN 37
+
+ #define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
+ #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral)
+ #define MAX7219_NUMBER_UNITS 2 // Number of Max7219 units in chain.
+ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
+ // connector at: right=0 bottom=-90 top=90 left=180
+
+ /**
+ * Sample debug features
+ * If you add more debug displays, be careful to avoid conflicts!
+ */
+ #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
+ #define MAX7219_DEBUG_PLANNER_HEAD 5 // Show the planner queue head position on this and the next LED matrix row
+ #define MAX7219_DEBUG_PLANNER_TAIL 6 // Show the planner queue tail position on this and the next LED matrix row
+
+ #define MAX7219_DEBUG_PLANNER_QUEUE 7 // Show the current planner queue depth on this and the next LED matrix row
+ // If you experience stuttering, reboots, etc. this option can reveal how
+ // tweaks made to the configuration are affecting the printer in real-time.
+#endif
+
+/**
+ * NanoDLP Sync support
+ *
+ * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp"
+ * string to enable synchronization with DLP projector exposure. This change will allow to use
+ * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
+ */
+//#define NANODLP_Z_SYNC
+#if ENABLED(NANODLP_Z_SYNC)
+ //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
+ // Default behaviour is limited to Z axis only.
+#endif
+
+/**
+ * WiFi Support (Espressif ESP32 WiFi)
+ */
+//#define WIFISUPPORT
+#if ENABLED(WIFISUPPORT)
+ #define WIFI_SSID "Wifi SSID"
+ #define WIFI_PWD "Wifi Password"
+#endif
+
+// Enable Marlin dev mode which adds some special commands
+//#define MARLIN_DEV_MODE
+
+#endif // CONFIGURATION_ADV_H