mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 11:43:47 +00:00
Add *_DRIVER_TYPE to example configs
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
This commit is contained in:
Scott Lahteine
parent
fbdbe53290
commit
e5c0b490c8
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -571,6 +571,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -552,6 +552,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -845,15 +845,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -863,8 +865,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -875,8 +879,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1044,23 +1050,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1106,62 +1101,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1316,25 +1278,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1380,7 +1329,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -561,6 +561,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -570,6 +570,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -561,6 +561,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -555,6 +555,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -555,6 +555,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -561,6 +561,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -532,6 +532,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -532,6 +532,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -566,6 +566,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -566,6 +566,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -566,6 +566,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -563,6 +563,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -550,6 +550,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -845,15 +845,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -863,8 +865,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 4
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -875,8 +879,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1044,23 +1050,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1106,62 +1101,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1316,25 +1278,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1380,7 +1329,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -553,6 +553,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,125 +1042,80 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
#define HAVE_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
#define Z_IS_TMC26X
|
||||
#define Z2_IS_TMC26X
|
||||
#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
|
||||
#define X_MAX_CURRENT 1200 // in mA
|
||||
#define X_SENSE_RESISTOR 50 // in mOhms
|
||||
#define X_MICROSTEPS 32 // number of microsteps
|
||||
#define X2_MAX_CURRENT 1000
|
||||
#define X2_SENSE_RESISTOR 91
|
||||
#define X2_MICROSTEPS 16
|
||||
|
||||
#define X2_MAX_CURRENT 1200
|
||||
#define X2_SENSE_RESISTOR 50
|
||||
#define X2_MICROSTEPS 32
|
||||
#define Y_MAX_CURRENT 1000
|
||||
#define Y_SENSE_RESISTOR 91
|
||||
#define Y_MICROSTEPS 16
|
||||
|
||||
#define Y_MAX_CURRENT 1200
|
||||
#define Y_SENSE_RESISTOR 50
|
||||
#define Y_MICROSTEPS 32
|
||||
#define Y2_MAX_CURRENT 1000
|
||||
#define Y2_SENSE_RESISTOR 91
|
||||
#define Y2_MICROSTEPS 16
|
||||
|
||||
#define Y2_MAX_CURRENT 1200
|
||||
#define Y2_SENSE_RESISTOR 50
|
||||
#define Y2_MICROSTEPS 32
|
||||
#define Z_MAX_CURRENT 1000
|
||||
#define Z_SENSE_RESISTOR 91
|
||||
#define Z_MICROSTEPS 16
|
||||
|
||||
#define Z_MAX_CURRENT 1200
|
||||
#define Z_SENSE_RESISTOR 50
|
||||
#define Z_MICROSTEPS 32
|
||||
#define Z2_MAX_CURRENT 1000
|
||||
#define Z2_SENSE_RESISTOR 91
|
||||
#define Z2_MICROSTEPS 16
|
||||
|
||||
#define Z2_MAX_CURRENT 1200
|
||||
#define Z2_SENSE_RESISTOR 50
|
||||
#define Z2_MICROSTEPS 32
|
||||
#define E0_MAX_CURRENT 1000
|
||||
#define E0_SENSE_RESISTOR 91
|
||||
#define E0_MICROSTEPS 16
|
||||
|
||||
#define E0_MAX_CURRENT 1200
|
||||
#define E0_SENSE_RESISTOR 50
|
||||
#define E0_MICROSTEPS 32
|
||||
#define E1_MAX_CURRENT 1000
|
||||
#define E1_SENSE_RESISTOR 91
|
||||
#define E1_MICROSTEPS 16
|
||||
|
||||
#define E1_MAX_CURRENT 1200
|
||||
#define E1_SENSE_RESISTOR 50
|
||||
#define E1_MICROSTEPS 32
|
||||
#define E2_MAX_CURRENT 1000
|
||||
#define E2_SENSE_RESISTOR 91
|
||||
#define E2_MICROSTEPS 16
|
||||
|
||||
#define E2_MAX_CURRENT 1200
|
||||
#define E2_SENSE_RESISTOR 50
|
||||
#define E2_MICROSTEPS 32
|
||||
#define E3_MAX_CURRENT 1000
|
||||
#define E3_SENSE_RESISTOR 91
|
||||
#define E3_MICROSTEPS 16
|
||||
|
||||
#define E3_MAX_CURRENT 1200
|
||||
#define E3_SENSE_RESISTOR 50
|
||||
#define E3_MICROSTEPS 32
|
||||
#define E4_MAX_CURRENT 1000
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#define E4_MAX_CURRENT 1200
|
||||
#define E4_SENSE_RESISTOR 50
|
||||
#define E4_MICROSTEPS 32
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1309,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1373,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -602,9 +602,32 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
/**
|
||||
* Endstop Noise Filter
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -562,6 +562,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE TMC2130
|
||||
#define Y_DRIVER_TYPE TMC2130
|
||||
#define Z_DRIVER_TYPE TMC2130
|
||||
//#define X2_DRIVER_TYPE A4988
|
||||
//#define Y2_DRIVER_TYPE A4988
|
||||
//#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE TMC2130
|
||||
//#define E1_DRIVER_TYPE A4988
|
||||
//#define E2_DRIVER_TYPE A4988
|
||||
//#define E3_DRIVER_TYPE A4988
|
||||
//#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -581,6 +581,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -840,15 +840,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -858,8 +860,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -870,8 +874,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1039,23 +1045,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1101,62 +1096,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1311,25 +1273,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1375,7 +1324,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -561,6 +561,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -551,6 +551,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -627,6 +627,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -617,6 +617,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -603,6 +603,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -844,15 +844,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -862,8 +864,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -874,8 +878,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1043,23 +1049,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1105,62 +1100,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1315,25 +1277,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1379,7 +1328,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -621,6 +621,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -839,15 +839,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -857,8 +859,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -869,8 +873,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1038,23 +1044,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1100,62 +1095,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1310,25 +1272,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1374,7 +1323,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -564,9 +564,32 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
/**
|
||||
* Endstop Noise Filter
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -554,6 +554,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -553,6 +553,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -837,15 +837,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -855,8 +857,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 30
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -867,8 +871,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 15000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1036,23 +1042,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1098,62 +1093,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1308,25 +1270,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1372,7 +1321,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
@ -556,6 +556,29 @@
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Specify Stepper Driver types
|
||||
* The options are used to determine driver pulse timings as well as more advanced functionality.
|
||||
* Stepper timing options can be overridden in Configuration_adv.h
|
||||
*
|
||||
* Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
|
||||
* TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
|
||||
* TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
|
||||
* TMC5130, TMC5130_STANDALONE
|
||||
* :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X2_DRIVER_TYPE A4988
|
||||
#define Y2_DRIVER_TYPE A4988
|
||||
#define Z2_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
#define E2_DRIVER_TYPE A4988
|
||||
#define E3_DRIVER_TYPE A4988
|
||||
#define E4_DRIVER_TYPE A4988
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
@ -838,15 +838,17 @@
|
||||
|
||||
/**
|
||||
* Minimum delay after setting the stepper DIR (in ns)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
*15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
* 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
|
||||
* 20 : Minimum for TMC2xxx drivers
|
||||
* 200 : Minimum for A4988 drivers
|
||||
* 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
|
||||
* 650 : Minimum for DRV8825 drivers
|
||||
* 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
|
||||
* 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_DIR_DELAY 0
|
||||
//#define MINIMUM_STEPPER_DIR_DELAY 650
|
||||
|
||||
/**
|
||||
* Minimum stepper driver pulse width (in µs)
|
||||
@ -856,8 +858,10 @@
|
||||
* 2 : Minimum for DRV8825 stepper drivers
|
||||
* 3 : Minimum for TB6600 stepper drivers
|
||||
* 30 : Minimum for TB6560 stepper drivers
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MINIMUM_STEPPER_PULSE 2
|
||||
//#define MINIMUM_STEPPER_PULSE 2
|
||||
|
||||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
@ -868,8 +872,10 @@
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 130000 : Maximum for LV8729 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
* Override the default value based on the driver type set in Configuration.h.
|
||||
*/
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
//#define MAXIMUM_STEPPER_RATE 250000
|
||||
|
||||
// @section temperature
|
||||
|
||||
@ -1037,23 +1043,12 @@
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* Enable this section if you have TMC26X motor drivers.
|
||||
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
* (https://github.com/trinamic/TMC26XStepper.git)
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
*/
|
||||
//#define HAVE_TMC26X
|
||||
#if ENABLED(HAVE_TMC26X) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC26X
|
||||
//#define X2_IS_TMC26X
|
||||
//#define Y_IS_TMC26X
|
||||
//#define Y2_IS_TMC26X
|
||||
//#define Z_IS_TMC26X
|
||||
//#define Z2_IS_TMC26X
|
||||
//#define E0_IS_TMC26X
|
||||
//#define E1_IS_TMC26X
|
||||
//#define E2_IS_TMC26X
|
||||
//#define E3_IS_TMC26X
|
||||
//#define E4_IS_TMC26X
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
#define X_MAX_CURRENT 1000 // in mA
|
||||
#define X_SENSE_RESISTOR 91 // in mOhms
|
||||
@ -1099,62 +1094,29 @@
|
||||
#define E4_SENSE_RESISTOR 91
|
||||
#define E4_MICROSTEPS 16
|
||||
|
||||
#endif
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
||||
*
|
||||
* You'll also need the TMC2130Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2130Stepper).
|
||||
*
|
||||
* To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
|
||||
* the hardware SPI interface on your board and define the required CS pins
|
||||
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
* Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
*
|
||||
* The TMC2130Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2130Stepper
|
||||
*
|
||||
* To use TMC2208 stepper UART-configurable stepper drivers
|
||||
* connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
|
||||
* To use the reading capabilities, also connect #_SERIAL_RX_PIN
|
||||
* to PDN_UART without a resistor.
|
||||
* The drivers can also be used with hardware serial.
|
||||
*
|
||||
* You'll also need the TMC2208Stepper Arduino library
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
* The TMC2208Stepper library is required for this stepper driver.
|
||||
* https://github.com/teemuatlut/TMC2208Stepper
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
//#define Y2_IS_TMC2208
|
||||
//#define Z_IS_TMC2208
|
||||
//#define Z2_IS_TMC2208
|
||||
//#define E0_IS_TMC2208
|
||||
//#define E1_IS_TMC2208
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
#if HAS_TRINAMIC
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@ -1309,25 +1271,12 @@
|
||||
// @section L6470
|
||||
|
||||
/**
|
||||
* Enable this section if you have L6470 motor drivers.
|
||||
* You need to import the L6470 library into the Arduino IDE for this.
|
||||
* (https://github.com/ameyer/Arduino-L6470)
|
||||
* L6470 Stepper Driver options
|
||||
*
|
||||
* The Arduino-L6470 library is required for this stepper driver.
|
||||
* https://github.com/ameyer/Arduino-L6470
|
||||
*/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
//#define X2_IS_L6470
|
||||
//#define Y_IS_L6470
|
||||
//#define Y2_IS_L6470
|
||||
//#define Z_IS_L6470
|
||||
//#define Z2_IS_L6470
|
||||
//#define E0_IS_L6470
|
||||
//#define E1_IS_L6470
|
||||
//#define E2_IS_L6470
|
||||
//#define E3_IS_L6470
|
||||
//#define E4_IS_L6470
|
||||
#if HAS_DRIVER(L6470)
|
||||
|
||||
#define X_MICROSTEPS 16 // number of microsteps
|
||||
#define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
@ -1373,7 +1322,7 @@
|
||||
#define E4_OVERCURRENT 2000
|
||||
#define E4_STALLCURRENT 1500
|
||||
|
||||
#endif
|
||||
#endif // L6470
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
|
||||
Loading…
Reference in New Issue
Block a user