diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index cbfa88e70a..da852ee5bc 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h index 1a59dfbc04..d044d7e6e3 100644 --- a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h +++ b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h @@ -369,29 +369,29 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Buda 2.0 on 24V - #define DEFAULT_Kp 6 - #define DEFAULT_Ki .3 - #define DEFAULT_Kd 125 + #define DEFAULT_Kp 6 + #define DEFAULT_Ki .3 + #define DEFAULT_Kd 125 // Buda 2.0 on 12V - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.01 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.01 + //#define DEFAULT_Kd 114 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -422,27 +422,27 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //24V 360W silicone heater from NPH on 3mm borosilicate (TAZ 2.2+) - #define DEFAULT_bedKp 20 - #define DEFAULT_bedKi 5 - #define DEFAULT_bedKd 275 + #define DEFAULT_bedKp 20 + #define DEFAULT_bedKi 5 + #define DEFAULT_bedKd 275 //12v 400W silicone heater from QUDB into 3mm borosilicate (TAZ 1.0+) //from pidautotune - //#define DEFAULT_bedKp 650 - //#define DEFAULT_bedKi 60 - //#define DEFAULT_bedKd 1800 + //#define DEFAULT_bedKp 650 + //#define DEFAULT_bedKi 60 + //#define DEFAULT_bedKd 1800 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h index 06564935de..7f6fe273ac 100644 --- a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h +++ b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Anet/A6/Configuration.h b/Marlin/example_configurations/Anet/A6/Configuration.h index 7a31cad6e1..7835a547c3 100644 --- a/Marlin/example_configurations/Anet/A6/Configuration.h +++ b/Marlin/example_configurations/Anet/A6/Configuration.h @@ -370,30 +370,30 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // ANET A6 Firmware V2.0 Standard Extruder defaults: // PID-P: +022.20, PID-I: +001.08, PID-D: +114.00, PID-C: 1 - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114.0 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114.0 // Tuned by ralf-e. Always re-tune for your machine! - #define DEFAULT_Kp 16.83 - #define DEFAULT_Ki 1.02 - #define DEFAULT_Kd 69.29 + #define DEFAULT_Kp 16.83 + #define DEFAULT_Ki 1.02 + #define DEFAULT_Kd 69.29 #endif // PIDTEMP @@ -425,24 +425,24 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // ANET A6 // original Bed + 0.3mm Heat conducting into 4mm borosilicate (PID-Autotune: M303 E-1 S60 C5): - //#define DEFAULT_bedKp 295.00 - //#define DEFAULT_bedKi 35.65 - //#define DEFAULT_bedKd 610.21 - #define DEFAULT_bedKp 295.00 - #define DEFAULT_bedKi 35.65 - #define DEFAULT_bedKd 610.21 + //#define DEFAULT_bedKp 295.00 + //#define DEFAULT_bedKi 35.65 + //#define DEFAULT_bedKd 610.21 + #define DEFAULT_bedKp 295.00 + #define DEFAULT_bedKi 35.65 + #define DEFAULT_bedKd 610.21 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Anet/A8/Configuration.h b/Marlin/example_configurations/Anet/A8/Configuration.h index e78ab2ba7c..5adfa47de4 100644 --- a/Marlin/example_configurations/Anet/A8/Configuration.h +++ b/Marlin/example_configurations/Anet/A8/Configuration.h @@ -371,25 +371,25 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 21.0 - //#define DEFAULT_Ki 1.25 - //#define DEFAULT_Kd 86.0 + //#define DEFAULT_Kp 21.0 + //#define DEFAULT_Ki 1.25 + //#define DEFAULT_Kd 86.0 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // ANET A8 Standard Extruder at 210 Degree Celsius and 100% Fan //(measured after M106 S255 with M303 E0 S210 C8) - #define DEFAULT_Kp 21.0 - #define DEFAULT_Ki 1.25 - #define DEFAULT_Kd 86.0 + #define DEFAULT_Kp 21.0 + #define DEFAULT_Ki 1.25 + #define DEFAULT_Kd 86.0 #endif // PIDTEMP @@ -421,15 +421,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h b/Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h index 9b7c6345fc..2ace0cfcf0 100644 --- a/Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h +++ b/Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 23.89 - #define DEFAULT_Ki 1.37 - #define DEFAULT_Kd 104.5 + #define DEFAULT_Kp 23.89 + #define DEFAULT_Ki 1.37 + #define DEFAULT_Kd 104.5 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 23.89 - #define DEFAULT_bedKi 1.37 - #define DEFAULT_bedKd 104.5 + #define DEFAULT_bedKp 23.89 + #define DEFAULT_bedKi 1.37 + #define DEFAULT_bedKd 104.5 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/BIBO/TouchX/default/Configuration.h b/Marlin/example_configurations/BIBO/TouchX/default/Configuration.h index bc4e2d884a..55cdb96434 100644 --- a/Marlin/example_configurations/BIBO/TouchX/default/Configuration.h +++ b/Marlin/example_configurations/BIBO/TouchX/default/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 23.89 - #define DEFAULT_Ki 1.37 - #define DEFAULT_Kd 104.5 + #define DEFAULT_Kp 23.89 + #define DEFAULT_Ki 1.37 + #define DEFAULT_Kd 104.5 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 23.89 - #define DEFAULT_bedKi 1.37 - #define DEFAULT_bedKd 104.5 + #define DEFAULT_bedKp 23.89 + #define DEFAULT_bedKi 1.37 + #define DEFAULT_bedKd 104.5 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/BQ/Hephestos/Configuration.h b/Marlin/example_configurations/BQ/Hephestos/Configuration.h index 2437b10230..0b3f2102c6 100644 --- a/Marlin/example_configurations/BQ/Hephestos/Configuration.h +++ b/Marlin/example_configurations/BQ/Hephestos/Configuration.h @@ -368,9 +368,9 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Hephestos i3 - #define DEFAULT_Kp 23.05 - #define DEFAULT_Ki 2.00 - #define DEFAULT_Kd 66.47 + #define DEFAULT_Kp 23.05 + #define DEFAULT_Ki 2.00 + #define DEFAULT_Kd 66.47 #endif // PIDTEMP @@ -402,15 +402,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h index 3c3a34e94a..a19c0c6b25 100644 --- a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h @@ -376,14 +376,14 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Tuned PID values using M303 - #define DEFAULT_Kp 19.18 - #define DEFAULT_Ki 1.36 - #define DEFAULT_Kd 67.42 + #define DEFAULT_Kp 19.18 + #define DEFAULT_Ki 1.36 + #define DEFAULT_Kd 67.42 // BQ firmware stock PID values - //#define DEFAULT_Kp 10.7 - //#define DEFAULT_Ki 0.45 - //#define DEFAULT_Kd 3 + //#define DEFAULT_Kp 10.7 + //#define DEFAULT_Ki 0.45 + //#define DEFAULT_Kd 3 #endif // PIDTEMP @@ -415,15 +415,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/BQ/WITBOX/Configuration.h b/Marlin/example_configurations/BQ/WITBOX/Configuration.h index 2e758e3366..cbe780f54f 100644 --- a/Marlin/example_configurations/BQ/WITBOX/Configuration.h +++ b/Marlin/example_configurations/BQ/WITBOX/Configuration.h @@ -368,9 +368,9 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Witbox - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 #endif // PIDTEMP @@ -402,15 +402,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index d35dcea7fa..732242517e 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -371,19 +371,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Cartesio extruderV6 40W Normal - #define DEFAULT_Kp 18 - #define DEFAULT_Ki 1 - #define DEFAULT_Kd 100 + #define DEFAULT_Kp 18 + #define DEFAULT_Ki 1 + #define DEFAULT_Kd 100 // Cartesio extruderV6 40W Volcano - //#define DEFAULT_Kp 50 - //#define DEFAULT_Ki 9 - //#define DEFAULT_Kd 70 + //#define DEFAULT_Kp 50 + //#define DEFAULT_Ki 9 + //#define DEFAULT_Kd 70 // Cartesio extruderV6 40W Cyclops - //#define DEFAULT_Kp 18 - //#define DEFAULT_Ki 1 - //#define DEFAULT_Kd 100 + //#define DEFAULT_Kp 18 + //#define DEFAULT_Ki 1 + //#define DEFAULT_Kd 100 #endif // PIDTEMP @@ -414,14 +414,14 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //24V 500W silicone heater on to 4mm glass CartesioW - #define DEFAULT_bedKp 390 - #define DEFAULT_bedKi 70 - #define DEFAULT_bedKd 546 + #define DEFAULT_bedKp 390 + #define DEFAULT_bedKi 70 + #define DEFAULT_bedKd 546 //24V 250W silicone heater on to 4mm glass CartesioM - //#define DEFAULT_bedKp 303 - //#define DEFAULT_bedKi 42 - //#define DEFAULT_bedKd 539 + //#define DEFAULT_bedKp 303 + //#define DEFAULT_bedKi 42 + //#define DEFAULT_bedKd 539 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Creality/CR-10/Configuration.h b/Marlin/example_configurations/Creality/CR-10/Configuration.h index 5a44a72955..e2ddd04d14 100755 --- a/Marlin/example_configurations/Creality/CR-10/Configuration.h +++ b/Marlin/example_configurations/Creality/CR-10/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Stock CR-10 tuned for 70C - #define DEFAULT_Kp 22.57 - #define DEFAULT_Ki 1.72 - #define DEFAULT_Kd 73.96 + #define DEFAULT_Kp 22.57 + #define DEFAULT_Ki 1.72 + #define DEFAULT_Kd 73.96 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -418,21 +418,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //Stock CR-10 Bed Tuned for 70C - #define DEFAULT_bedKp 426.68 - #define DEFAULT_bedKi 78.92 - #define DEFAULT_bedKd 576.71 + #define DEFAULT_bedKp 426.68 + #define DEFAULT_bedKi 78.92 + #define DEFAULT_bedKd 576.71 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Creality/CR-10S/Configuration.h b/Marlin/example_configurations/Creality/CR-10S/Configuration.h index f1e4229705..aa7de30e16 100644 --- a/Marlin/example_configurations/Creality/CR-10S/Configuration.h +++ b/Marlin/example_configurations/Creality/CR-10S/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Creality/CR-10mini/Configuration.h b/Marlin/example_configurations/Creality/CR-10mini/Configuration.h index f3edd69757..34aa0130ab 100644 --- a/Marlin/example_configurations/Creality/CR-10mini/Configuration.h +++ b/Marlin/example_configurations/Creality/CR-10mini/Configuration.h @@ -379,24 +379,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Stock CR-10 tuned for 70C - #define DEFAULT_Kp 22.57 - #define DEFAULT_Ki 1.72 - #define DEFAULT_Kd 73.96 + #define DEFAULT_Kp 22.57 + #define DEFAULT_Ki 1.72 + #define DEFAULT_Kd 73.96 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -427,21 +427,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //Stock CR-10 Bed Tuned for 70C - #define DEFAULT_bedKp 426.68 - #define DEFAULT_bedKi 78.92 - #define DEFAULT_bedKd 576.71 + #define DEFAULT_bedKp 426.68 + #define DEFAULT_bedKi 78.92 + #define DEFAULT_bedKd 576.71 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Creality/Ender-2/Configuration.h b/Marlin/example_configurations/Creality/Ender-2/Configuration.h index 701cbd3978..32fa6ea576 100644 --- a/Marlin/example_configurations/Creality/Ender-2/Configuration.h +++ b/Marlin/example_configurations/Creality/Ender-2/Configuration.h @@ -369,24 +369,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Creality Ender - #define DEFAULT_Kp 21.73 - #define DEFAULT_Ki 1.54 - #define DEFAULT_Kd 76.55 + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -418,15 +418,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Creality/Ender-4/Configuration.h b/Marlin/example_configurations/Creality/Ender-4/Configuration.h index fb0c40f165..37dac7f724 100644 --- a/Marlin/example_configurations/Creality/Ender-4/Configuration.h +++ b/Marlin/example_configurations/Creality/Ender-4/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ender-4 - #define DEFAULT_Kp 22.57 - #define DEFAULT_Ki 1.72 - #define DEFAULT_Kd 73.96 + #define DEFAULT_Kp 22.57 + #define DEFAULT_Ki 1.72 + #define DEFAULT_Kd 73.96 // Ultimaker -// #define DEFAULT_Kp 22.2 -// #define DEFAULT_Ki 1.08 -// #define DEFAULT_Kd 114 +// #define DEFAULT_Kp 22.2 +// #define DEFAULT_Ki 1.08 +// #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -418,21 +418,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. // Ender-4 - #define DEFAULT_bedKp 426.68 - #define DEFAULT_bedKi 78.92 - #define DEFAULT_bedKd 576.71 + #define DEFAULT_bedKp 426.68 + #define DEFAULT_bedKi 78.92 + #define DEFAULT_bedKd 576.71 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h index e9a4590aab..f18eae3688 100644 --- a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h +++ b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // FolgerTech i3-2020 - #define DEFAULT_Kp 11.50 - #define DEFAULT_Ki 0.50 - #define DEFAULT_Kd 60.00 + #define DEFAULT_Kp 11.50 + #define DEFAULT_Ki 0.50 + #define DEFAULT_Kd 60.00 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -419,15 +419,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 250.0 - #define DEFAULT_bedKi 18.0 - #define DEFAULT_bedKd 950.0 + #define DEFAULT_bedKp 250.0 + #define DEFAULT_bedKi 18.0 + #define DEFAULT_bedKd 950.0 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h index 7106cf0fef..b83876dd4a 100644 --- a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h +++ b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h @@ -368,31 +368,31 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Geeetech MK8 Extruder - #define DEFAULT_Kp 12.33 - #define DEFAULT_Ki 0.51 - #define DEFAULT_Kd 74.50 + #define DEFAULT_Kp 12.33 + #define DEFAULT_Ki 0.51 + #define DEFAULT_Kd 74.50 // CTC MK8 Extruder - //#define DEFAULT_Kp 19.86 - //#define DEFAULT_Ki 1.0 - //#define DEFAULT_Kd 98.83 + //#define DEFAULT_Kp 19.86 + //#define DEFAULT_Ki 1.0 + //#define DEFAULT_Kd 98.83 // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -423,21 +423,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) - #define DEFAULT_bedKp 234.88 - #define DEFAULT_bedKi 42.79 - #define DEFAULT_bedKd 322.28 + #define DEFAULT_bedKp 234.88 + #define DEFAULT_bedKi 42.79 + #define DEFAULT_bedKd 322.28 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h index 5ee1d62018..c7ddcea432 100644 --- a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 84a9a6afa2..f192ff22f2 100644 --- a/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -368,31 +368,31 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Geeetech MK8 Extruder - #define DEFAULT_Kp 12.33 - #define DEFAULT_Ki 0.51 - #define DEFAULT_Kd 74.50 + #define DEFAULT_Kp 12.33 + #define DEFAULT_Ki 0.51 + #define DEFAULT_Kd 74.50 // CTC MK8 Extruder - //#define DEFAULT_Kp 19.86 - //#define DEFAULT_Ki 1.0 - //#define DEFAULT_Kd 98.83 + //#define DEFAULT_Kp 19.86 + //#define DEFAULT_Ki 1.0 + //#define DEFAULT_Kd 98.83 // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -423,21 +423,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) - #define DEFAULT_bedKp 234.88 - #define DEFAULT_bedKi 42.79 - #define DEFAULT_bedKd 322.28 + #define DEFAULT_bedKp 234.88 + #define DEFAULT_bedKi 42.79 + #define DEFAULT_bedKd 322.28 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 523f7ffc81..bd298f3bfd 100644 --- a/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -368,31 +368,31 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Geeetech MK8 Extruder - #define DEFAULT_Kp 12.33 - #define DEFAULT_Ki 0.51 - #define DEFAULT_Kd 74.50 + #define DEFAULT_Kp 12.33 + #define DEFAULT_Ki 0.51 + #define DEFAULT_Kd 74.50 // CTC MK8 Extruder - //#define DEFAULT_Kp 19.86 - //#define DEFAULT_Ki 1.0 - //#define DEFAULT_Kd 98.83 + //#define DEFAULT_Kp 19.86 + //#define DEFAULT_Ki 1.0 + //#define DEFAULT_Kd 98.83 // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -423,21 +423,21 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) - #define DEFAULT_bedKp 234.88 - #define DEFAULT_bedKi 42.79 - #define DEFAULT_bedKd 322.28 + #define DEFAULT_bedKp 234.88 + #define DEFAULT_bedKi 42.79 + #define DEFAULT_bedKd 322.28 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h index b6c8957e8c..cfa933f243 100644 --- a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h +++ b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h @@ -370,23 +370,23 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 - #define DEFAULT_Kp 213.2 - #define DEFAULT_Ki 1.54 - #define DEFAULT_Kd 765 + #define DEFAULT_Kp 213.2 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 765 #endif // PIDTEMP @@ -418,15 +418,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/JGAurora/A5/Configuration.h b/Marlin/example_configurations/JGAurora/A5/Configuration.h index e3df0e6927..a7e4a301fa 100644 --- a/Marlin/example_configurations/JGAurora/A5/Configuration.h +++ b/Marlin/example_configurations/JGAurora/A5/Configuration.h @@ -375,24 +375,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // JGAurora A5 (tuned at 210C) - #define DEFAULT_Kp 35.3//22.2 - #define DEFAULT_Ki 4.35//1.08 - #define DEFAULT_Kd 71.57//114 + #define DEFAULT_Kp 35.3//22.2 + #define DEFAULT_Ki 4.35//1.08 + #define DEFAULT_Kd 71.57//114 #endif // PIDTEMP @@ -426,15 +426,15 @@ //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) // JGAurora A5 (tuned at 70C) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Malyan/M150/Configuration.h b/Marlin/example_configurations/Malyan/M150/Configuration.h index 6ac1d6eaa9..587c3f66bf 100644 --- a/Marlin/example_configurations/Malyan/M150/Configuration.h +++ b/Marlin/example_configurations/Malyan/M150/Configuration.h @@ -378,19 +378,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Malyan M150 example - #define DEFAULT_Kp 29 - #define DEFAULT_Ki 2 - #define DEFAULT_Kd 97 + #define DEFAULT_Kp 29 + #define DEFAULT_Ki 2 + #define DEFAULT_Kd 97 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -422,15 +422,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Micromake/C1/basic/Configuration.h b/Marlin/example_configurations/Micromake/C1/basic/Configuration.h index 4eea560b7e..5d02e0fbd7 100644 --- a/Marlin/example_configurations/Micromake/C1/basic/Configuration.h +++ b/Marlin/example_configurations/Micromake/C1/basic/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h index b108a5f945..b3250d6c70 100644 --- a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h +++ b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index f9efdcca59..3d6327a786 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 0fae6dd8d8..565cd577ec 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -373,19 +373,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Rigidbot hotend - #define DEFAULT_Kp 16.17 - #define DEFAULT_Ki 0.85 - #define DEFAULT_Kd 76.55 + #define DEFAULT_Kp 16.17 + #define DEFAULT_Ki 0.85 + #define DEFAULT_Kd 76.55 // Base DGlass3D/E3Dv6 hotend - //#define DEFAULT_Kp 10 - //#define DEFAULT_Ki 0.85 - //#define DEFAULT_Kd 245 + //#define DEFAULT_Kp 10 + //#define DEFAULT_Ki 0.85 + //#define DEFAULT_Kd 245 // E3D w/ rigidbot cartridge - //#define DEFAULT_Kp 16.30 - //#define DEFAULT_Ki 0.95 - //#define DEFAULT_Kd 69.69 + //#define DEFAULT_Kp 16.30 + //#define DEFAULT_Ki 0.95 + //#define DEFAULT_Kd 69.69 #endif // PIDTEMP @@ -416,9 +416,9 @@ //#define PID_BED_DEBUG // Sends debug data to the serial port. //RigidBot, from pid autotune - #define DEFAULT_bedKp 355 - #define DEFAULT_bedKi 66.5 - #define DEFAULT_bedKd 480 + #define DEFAULT_bedKp 355 + #define DEFAULT_bedKi 66.5 + #define DEFAULT_bedKd 480 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index b918d757e3..0228164fd3 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -397,9 +397,9 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Merlin Hotend: From Autotune - #define DEFAULT_Kp 24.5 - #define DEFAULT_Ki 1.72 - #define DEFAULT_Kd 87.73 + #define DEFAULT_Kp 24.5 + #define DEFAULT_Ki 1.72 + #define DEFAULT_Kd 87.73 #endif // PIDTEMP @@ -431,9 +431,9 @@ //12v Heatbed Mk3 12V in parallel //from pidautotune - #define DEFAULT_bedKp 630.14 - #define DEFAULT_bedKi 121.71 - #define DEFAULT_bedKd 815.64 + #define DEFAULT_bedKp 630.14 + #define DEFAULT_bedKi 121.71 + #define DEFAULT_bedKd 815.64 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Sanguinololu/Configuration.h b/Marlin/example_configurations/Sanguinololu/Configuration.h index 6f1111af7c..5c96a16a67 100644 --- a/Marlin/example_configurations/Sanguinololu/Configuration.h +++ b/Marlin/example_configurations/Sanguinololu/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h index 10e00cffd9..c1d8324d46 100644 --- a/Marlin/example_configurations/TinyBoy2/Configuration.h +++ b/Marlin/example_configurations/TinyBoy2/Configuration.h @@ -397,30 +397,30 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // TinyBoy2 Extruder - calculated with PID Autotune and tested // "M303 E0 C8 S200" - //#define DEFAULT_Kp 25.63 - //#define DEFAULT_Ki 2.66 - //#define DEFAULT_Kd 61.73 + //#define DEFAULT_Kp 25.63 + //#define DEFAULT_Ki 2.66 + //#define DEFAULT_Kd 61.73 // TinyBoy2 Extruder - same, but with fan @ 25% duty - #define DEFAULT_Kp 26.15 - #define DEFAULT_Ki 2.71 - #define DEFAULT_Kd 63.02 + #define DEFAULT_Kp 26.15 + #define DEFAULT_Ki 2.71 + #define DEFAULT_Kd 63.02 #endif // PIDTEMP //=========================================================================== @@ -451,29 +451,29 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. // TinyBoy2 heatbed - calculated with PID Autotune and tested // "M303 E-1 C8 S75" - //#define DEFAULT_bedKp 421.80 - //#define DEFAULT_bedKi 82.51 - //#define DEFAULT_bedKd 539.06 + //#define DEFAULT_bedKp 421.80 + //#define DEFAULT_bedKi 82.51 + //#define DEFAULT_bedKd 539.06 // TinyBoy2 heatbed - same, but with fan @ 25% duty // "M303 E-1 C8 S75" - #define DEFAULT_bedKp 267.54 - #define DEFAULT_bedKi 52.34 - #define DEFAULT_bedKd 341.92 + #define DEFAULT_bedKp 267.54 + #define DEFAULT_bedKi 52.34 + #define DEFAULT_bedKd 341.92 #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Tronxy/X1/Configuration.h b/Marlin/example_configurations/Tronxy/X1/Configuration.h index 8b9c70283e..659fbc6a42 100644 --- a/Marlin/example_configurations/Tronxy/X1/Configuration.h +++ b/Marlin/example_configurations/Tronxy/X1/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Tronxy X1 - #define DEFAULT_Kp 16.20 - #define DEFAULT_Ki 1.11 - #define DEFAULT_Kd 59.06 + #define DEFAULT_Kp 16.20 + #define DEFAULT_Ki 1.11 + #define DEFAULT_Kd 59.06 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Tronxy/X5S/Configuration.h b/Marlin/example_configurations/Tronxy/X5S/Configuration.h index c8c11883ce..6d69d8447c 100644 --- a/Marlin/example_configurations/Tronxy/X5S/Configuration.h +++ b/Marlin/example_configurations/Tronxy/X5S/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Tronxy/XY100/Configuration.h b/Marlin/example_configurations/Tronxy/XY100/Configuration.h index e8ee862dd1..d092d66eef 100644 --- a/Marlin/example_configurations/Tronxy/XY100/Configuration.h +++ b/Marlin/example_configurations/Tronxy/XY100/Configuration.h @@ -370,30 +370,30 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - // #define DEFAULT_Kp 22.2 - // #define DEFAULT_Ki 1.08 - // #define DEFAULT_Kd 114 + // #define DEFAULT_Kp 22.2 + // #define DEFAULT_Ki 1.08 + // #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // TronXY XY-100 Standard Extruder at 210 Degree Celsius and 100% Fan // (measured after M106 S255 with M303 E0 S210 C8) - // #define DEFAULT_Kp 20.32 - // #define DEFAULT_Ki 1.18 - // #define DEFAULT_Kd 87.80 + // #define DEFAULT_Kp 20.32 + // #define DEFAULT_Ki 1.18 + // #define DEFAULT_Kd 87.80 // TronXY XY-100 Standard Extruder, from original firmware - #define DEFAULT_Kp 7.0000 - #define DEFAULT_Ki 2.0000 - #define DEFAULT_Kd 40.0000 + #define DEFAULT_Kp 7.0000 + #define DEFAULT_Ki 2.0000 + #define DEFAULT_Kd 40.0000 #endif // PIDTEMP @@ -425,15 +425,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Velleman/K8200/Configuration.h b/Marlin/example_configurations/Velleman/K8200/Configuration.h index 12aa3bdc5e..35ea87001f 100644 --- a/Marlin/example_configurations/Velleman/K8200/Configuration.h +++ b/Marlin/example_configurations/Velleman/K8200/Configuration.h @@ -390,24 +390,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // Vellemann K8200 Extruder - calculated with PID Autotune and tested - #define DEFAULT_Kp 24.29 - #define DEFAULT_Ki 1.58 - #define DEFAULT_Kd 93.51 + #define DEFAULT_Kp 24.29 + #define DEFAULT_Ki 1.58 + #define DEFAULT_Kd 93.51 #endif // PIDTEMP //=========================================================================== @@ -438,23 +438,23 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. // Vellemann K8200 PCB heatbed with standard PCU at 60 degreesC - calculated with PID Autotune and tested // from pidautotune - #define DEFAULT_bedKp 341.88 - #define DEFAULT_bedKi 25.32 - #define DEFAULT_bedKd 1153.89 + #define DEFAULT_bedKp 341.88 + #define DEFAULT_bedKi 25.32 + #define DEFAULT_bedKd 1153.89 #endif // PIDTEMPBED // @section extruder diff --git a/Marlin/example_configurations/Velleman/K8400/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Configuration.h index 52db6f132a..44c210c491 100644 --- a/Marlin/example_configurations/Velleman/K8400/Configuration.h +++ b/Marlin/example_configurations/Velleman/K8400/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - #define DEFAULT_Kp 63.0 - #define DEFAULT_Ki 2.25 - #define DEFAULT_Kd 440 + #define DEFAULT_Kp 63.0 + #define DEFAULT_Ki 2.25 + #define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h index b84d274708..99877d2af1 100644 --- a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h +++ b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - #define DEFAULT_Kp 63.0 - #define DEFAULT_Ki 2.25 - #define DEFAULT_Kd 440 + #define DEFAULT_Kp 63.0 + #define DEFAULT_Ki 2.25 + #define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h index 340e69b3f1..85ed2573e0 100644 --- a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h +++ b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // Duplicator 6 - #define DEFAULT_Kp 9.12 - #define DEFAULT_Ki 0.41 - #define DEFAULT_Kd 50.98 + #define DEFAULT_Kp 9.12 + #define DEFAULT_Ki 0.41 + #define DEFAULT_Kd 50.98 #endif // PIDTEMP @@ -419,20 +419,20 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) -// #define DEFAULT_bedKp 10.00 -// #define DEFAULT_bedKi .023 -// #define DEFAULT_bedKd 305.4 +// #define DEFAULT_bedKp 10.00 +// #define DEFAULT_bedKi .023 +// #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // Duplicator 6 - #define DEFAULT_bedKp 124.55 - #define DEFAULT_bedKi 23.46 - #define DEFAULT_bedKd 165.29 + #define DEFAULT_bedKp 124.55 + #define DEFAULT_bedKi 23.46 + #define DEFAULT_bedKd 165.29 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 9722a76811..c58aebf02b 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h index 8b0b4d1cf0..48324dc596 100644 --- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 //E3D with 30MM fan - #define DEFAULT_Kp 24.77 - #define DEFAULT_Ki 1.84 - #define DEFAULT_Kd 83.61 + #define DEFAULT_Kp 24.77 + #define DEFAULT_Ki 1.84 + #define DEFAULT_Kd 83.61 #endif // PIDTEMP @@ -419,20 +419,20 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 //D-force - #define DEFAULT_bedKp 22.97 - #define DEFAULT_bedKi 3.76 - #define DEFAULT_bedKd 29.2 + #define DEFAULT_bedKp 22.97 + #define DEFAULT_bedKi 3.76 + #define DEFAULT_bedKd 29.2 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h index 541a99e8c0..7dd3ae0288 100644 --- a/Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 //E3D with 30MM fan - #define DEFAULT_Kp 24.77 - #define DEFAULT_Ki 1.84 - #define DEFAULT_Kd 83.61 + #define DEFAULT_Kp 24.77 + #define DEFAULT_Ki 1.84 + #define DEFAULT_Kd 83.61 #endif // PIDTEMP @@ -419,20 +419,20 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 //D-force - #define DEFAULT_bedKp 22.97 - #define DEFAULT_bedKi 3.76 - #define DEFAULT_bedKd 29.2 + #define DEFAULT_bedKp 22.97 + #define DEFAULT_bedKi 3.76 + #define DEFAULT_bedKd 29.2 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h index 6331f9f283..b89357abb7 100644 --- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 //E3D with 30MM fan - #define DEFAULT_Kp 24.77 - #define DEFAULT_Ki 1.84 - #define DEFAULT_Kd 83.61 + #define DEFAULT_Kp 24.77 + #define DEFAULT_Ki 1.84 + #define DEFAULT_Kd 83.61 #endif // PIDTEMP @@ -419,20 +419,20 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 //D-force - #define DEFAULT_bedKp 22.97 - #define DEFAULT_bedKi 3.76 - #define DEFAULT_bedKd 29.2 + #define DEFAULT_bedKp 22.97 + #define DEFAULT_bedKi 3.76 + #define DEFAULT_bedKd 29.2 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h b/Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h index 20e9bb27cf..40dca155cd 100644 --- a/Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h +++ b/Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h @@ -375,24 +375,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 // E3D-v6 - #define DEFAULT_Kp 18.55 - #define DEFAULT_Ki 2.71 - #define DEFAULT_Kd 47.69 + #define DEFAULT_Kp 18.55 + #define DEFAULT_Ki 2.71 + #define DEFAULT_Kd 47.69 #endif // PIDTEMP @@ -424,20 +424,20 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 //HatchBox Alpha - #define DEFAULT_bedKp 72.11 - #define DEFAULT_bedKi 7.1 - #define DEFAULT_bedKd 488.31 + #define DEFAULT_bedKp 72.11 + #define DEFAULT_bedKi 7.1 + #define DEFAULT_bedKd 488.31 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 46f118baa8..b166e8cfbd 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 103a383e55..3075ab3a2b 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -414,15 +414,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index e6a1a72ae8..7beec86c19 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -372,9 +372,9 @@ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // Kossel Pro - #define DEFAULT_Kp 19.30 - #define DEFAULT_Ki 3.51 - #define DEFAULT_Kd 26.56 + #define DEFAULT_Kp 19.30 + #define DEFAULT_Ki 3.51 + #define DEFAULT_Kd 26.56 #endif // PIDTEMP @@ -406,9 +406,9 @@ //Kossel Pro heated bed plate with borosilicate glass //from pidautotune (M303 E-1 S60 C8) - #define DEFAULT_bedKp 370.25 - #define DEFAULT_bedKi 62.77 - #define DEFAULT_bedKd 545.98 + #define DEFAULT_bedKp 370.25 + #define DEFAULT_bedKi 62.77 + #define DEFAULT_bedKd 545.98 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index 24f2360034..f17d96982d 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -379,14 +379,14 @@ //#define DEFAULT_Kd 85.30 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -418,15 +418,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 15.00 - #define DEFAULT_bedKi .04 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 15.00 + #define DEFAULT_bedKi .04 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h index 789e54154b..fcb0fb1897 100644 --- a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h +++ b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h @@ -378,24 +378,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // gMax J-Head - #define DEFAULT_Kp 15.35 - #define DEFAULT_Ki 0.85 - #define DEFAULT_Kd 69.45 + #define DEFAULT_Kp 15.35 + #define DEFAULT_Ki 0.85 + #define DEFAULT_Kd 69.45 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -427,15 +427,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 135.44 - #define DEFAULT_bedKi 24.60 - #define DEFAULT_bedKd 186.40 + #define DEFAULT_bedKp 135.44 + #define DEFAULT_bedKi 24.60 + #define DEFAULT_bedKd 186.40 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 8b54c1faeb..b8a78a10b5 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -370,19 +370,19 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -417,15 +417,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index e658e49fee..39ae9a1991 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -369,9 +369,9 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // J-Head Mk V-B - #define DEFAULT_Kp 25.05 - #define DEFAULT_Ki 2.30 - #define DEFAULT_Kd 68.15 + #define DEFAULT_Kp 25.05 + #define DEFAULT_Ki 2.30 + #define DEFAULT_Kd 68.15 #endif // PIDTEMP @@ -403,15 +403,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/wt150/Configuration.h b/Marlin/example_configurations/wt150/Configuration.h index c1905a3835..af5c04f256 100644 --- a/Marlin/example_configurations/wt150/Configuration.h +++ b/Marlin/example_configurations/wt150/Configuration.h @@ -370,24 +370,24 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it //WT150, based on: M303 E0 S220 C8 - #define DEFAULT_Kp 22.10 - #define DEFAULT_Ki 1.10 - #define DEFAULT_Kd 110.78 + #define DEFAULT_Kp 22.10 + #define DEFAULT_Ki 1.10 + #define DEFAULT_Kd 110.78 // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 #endif // PIDTEMP @@ -419,15 +419,15 @@ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index bfa3081f9f..063fd68c18 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -451,17 +451,17 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS], #if HAS_PID_FOR_BOTH const char* estring = hotend < 0 ? "bed" : ""; - SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kp ", workKp); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Ki ", workKi); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kd ", workKd); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kp ", workKp); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Ki ", workKi); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_", estring); SERIAL_PROTOCOLPAIR("Kd ", workKd); SERIAL_EOL(); #elif ENABLED(PIDTEMP) - SERIAL_PROTOCOLPAIR("#define DEFAULT_Kp ", workKp); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_Ki ", workKi); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_Kd ", workKd); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_Kp ", workKp); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_Ki ", workKi); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_Kd ", workKd); SERIAL_EOL(); #else - SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKp ", workKp); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKi ", workKi); SERIAL_EOL(); - SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKd ", workKd); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKp ", workKp); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKi ", workKi); SERIAL_EOL(); + SERIAL_PROTOCOLPAIR("#define DEFAULT_bedKd ", workKd); SERIAL_EOL(); #endif #define _SET_BED_PID() do { \