Robert F-C
1292d735ba
Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575)
...
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
2013-02-28 02:04:51 +11:00
MendelMax
67710df9f3
Made i2c mode wok with the hardware I am able to test (ywrobot / sainsmart i2c LCD 2004)
...
Removed incorrect LiquidCrystal_I2C Library
2013-02-26 22:22:12 +00:00
Bob Clough
2b567d1df5
Added I2C port expander support to HD44780
2013-02-25 14:22:14 +00:00
Bob Clough
06272f463d
Added Config variables for activating I2C LCDs and setting type and address
2013-02-25 14:14:46 +00:00
Daniele Sdei
9ecb267b63
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
2013-01-14 15:47:40 +01:00
Daniele Sdei
3cf59f6f9a
add RepRapPro Huxley thermistor tables
2013-01-14 15:36:08 +01:00
daid303
bbe7d3d0fe
Fixed #312
2013-01-08 17:09:57 +01:00
daid303
8b88e3b386
Fixed #345 , Fixed #267 .
2013-01-08 12:14:55 +01:00
Nicolas Rossi
f3c1fc70a9
Power signal control definitions for ATX and others
2013-01-07 14:33:30 +01:00
daid303
55ba90ac19
Add PID functional range setting. With high powered heaters the current functional range of 10 degrees causes high overshoots as the PID needs to kick in before the temperature hits 10 degrees below target.
2012-12-12 09:08:37 +01:00
daid303
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
2012-12-11 14:53:53 +01:00
Johann Rocholl
1f45cb0a51
Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.
2012-12-11 01:54:40 -08:00
Johann Rocholl
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
2012-12-08 10:49:01 -08:00
Erik vd Zalm
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
2012-11-21 20:36:30 +01:00
Martin Lukasik
2f771b3979
Added automatic build numbering.
2012-11-12 21:06:59 +00:00
daid303
a27fef8750
Store the pre-heat constants outside of the ULTIPANEL define, so we can use them when storing EEPROM in a build without the ULTIPANEL.
2012-11-11 11:06:58 +01:00
daid303
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
2012-11-09 09:10:51 +01:00
Jonathan Bastien-Filiatrault
46b9988e26
Search and replace failure.
2012-11-07 16:09:30 -05:00
Jonathan Bastien-Filiatrault
36b452c7ac
Remove abbrs.
2012-11-07 15:42:18 -05:00
Jonathan Bastien-Filiatrault
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
2012-11-06 20:32:13 -05:00
Robert F-C
65c9a0728f
Set default serial port back to 0.
2012-11-05 22:15:07 +11:00
Robert F-C
ab9d183024
Make serial port configurable.
...
This change makes the choice of serial port configurable so that
wireless capability can be easily added by connecting Bluetooth modules
(such as BlueSmirf or JY-MCU) to the expansion port pins.
2012-11-05 21:34:27 +11:00
brupje
326423719f
Add support for Megatronics
2012-10-14 14:05:57 +03:00
ErikZalm
36a746d7d5
Merge pull request #244 from markfinn/pidbed
...
PID for heated bed
2012-10-08 11:15:16 -07:00
Mark Finn
04631d2250
cleanup for pull
2012-09-17 14:17:24 -05:00
ZetaPhoenix
c6caa45ae2
Limit Switch locations based on MIN/MAX limits and homing direction
...
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
2012-09-15 15:25:49 -07:00
ZetaPhoenix
dc566d654f
fixes #246
...
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
2012-09-14 21:48:49 -07:00
Mark Finn
9698f4ea64
bed pid
...
Conflicts:
Marlin/Configuration.h
2012-09-12 21:18:59 -05:00
Erik vd Zalm
e358a2d7af
Added fix for SF Arc Point fillet procedure
2012-09-02 01:12:49 +02:00
tonokip
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
2012-08-30 00:16:57 -07:00
Erik vd Zalm
5406c533db
Disable FAST_PWM by default. On some systems it does not work ok.
2012-08-11 15:51:04 +02:00
Dabble63
6b45e9f167
Add Duty Cycling to the Heater Bed
2012-08-11 09:17:47 +03:00
Chris Palmer
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
2012-07-14 22:24:26 +02:00
Erik van der Zalm
ea2c19f978
Added CoreXY support (Thanks Ilan Moyer)
2012-07-14 14:21:53 +02:00
Erik van der Zalm
aa65fe22ed
decoupled axes sucessfully at least on pure x or y jog
2012-07-14 13:43:19 +02:00
Bernhard
0c123950e9
__ header file replace
2012-06-02 20:44:17 +02:00
Bernhard
0e5e249ab5
added individual pullup setting option to have finer control in case there is a special z-min sensor, for example
2012-06-02 13:47:50 +02:00
Bernhard Kubicek
6b14f95b3e
Merge pull request #170 from linagee/Marlin_v1
...
Marlin v1
2012-06-02 03:46:56 -07:00
linagee
fbd282b3ba
Update Marlin/Configuration.h
2012-05-20 13:19:28 -06:00
linagee
c4490f5f3d
Update Marlin/Configuration.h
2012-05-20 04:27:52 -06:00
Daid
7244aa7eb7
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
2012-05-19 17:38:46 +02:00
linagee
de2ca3b2e8
Grammar correction.
2012-05-19 07:40:35 -06:00
linagee
c2fc466e1b
Update Marlin/Configuration.h
2012-05-19 05:56:17 -06:00
linagee
9f9f498491
Update Marlin/Configuration.h
2012-05-19 05:47:30 -06:00
Guan Yang
602c8ee02b
Melzi support
2012-05-09 18:37:07 -04:00
Erik de Bruijn
e3fe1f0d00
Made a more granular configuration possible PREVENT_LENGTHY_EXTRUDE. You can now decide to allow/disallow large length of extrusions to be executed.
...
Turning off the protection might be beneficial to those who want to do fast and long reversals.
2012-05-08 17:44:08 +02:00
Erik van der Zalm
1874cb71a6
Added option to increase the FAN PWM frequency.
2012-05-02 19:26:14 +02:00
Erik van der Zalm
e3821bd86f
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
2012-04-30 13:36:27 +02:00
Erik van der Zalm
02af69911e
Added temperature window to M109. This is needed for systems with no overshoot PID.
2012-04-30 13:36:19 +02:00
Bernhard
464b755918
added support for the UltiController
2012-04-22 20:55:56 +02:00
