Scott Lahteine
27b80b1dd1
Merge pull request #4667 from thinkyhead/rc_M211_sw_endstop_switch
...
M211: Enable/Disable Software Endstops
2016-08-21 06:44:00 -05:00
Scott Lahteine
2f223b8c79
Use ABC and XYZ for "3"
2016-08-21 00:10:08 -05:00
Scott Lahteine
4cd1ad8f28
Adjustments to M209, G28, M605
2016-08-21 00:10:08 -05:00
Scott Lahteine
280534c06f
Add M211: Enable/Disable Software Endstops
2016-08-21 00:10:08 -05:00
Scott Lahteine
01d4703429
PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION
...
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
2016-08-20 23:35:27 -05:00
MagoKimbra
28d1e5a946
Fix_Zig_Zag
2016-08-20 11:28:08 +02:00
Scott Lahteine
4d4c00d69c
Merge pull request #4651 from thinkyhead/rc_homing_vs_leveling_z
...
Improvements to homing / leveling
2016-08-19 15:45:49 -05:00
Scott Lahteine
12d72363cb
Do Delta radius check without sqrt
2016-08-19 05:05:48 -05:00
Scott Lahteine
044f800be9
Use SERIAL_PROTOCOLLNPGM in G28
2016-08-19 04:45:33 -05:00
Scott Lahteine
d309a9647d
Include probe offset for moving "close to the bed"
2016-08-19 04:45:33 -05:00
Scott Lahteine
35a08eeaeb
Use Z_HOME_DIR over axis_home_dir where we can
2016-08-19 04:45:32 -05:00
Scott Lahteine
55355a4fb8
Make probed points more symmetrical
2016-08-19 04:32:03 -05:00
Scott Lahteine
1f776f6034
Tweak some code comments
2016-08-19 04:32:02 -05:00
Scott Lahteine
748228cf40
Use named indices for delta_grid_spacing
2016-08-19 04:32:02 -05:00
Scott Lahteine
ead333e7da
line_to_axis_pos => do_homing_move
2016-08-19 04:32:02 -05:00
Scott Lahteine
7a4ccd7967
Add do_probe_move with Z fixes
2016-08-19 04:32:02 -05:00
Scott Lahteine
a1bad589c9
Augment debug/homing logging
2016-08-19 04:32:02 -05:00
Scott Lahteine
41b5c48129
Update software endstops if EEPROM is loaded
2016-08-19 04:32:01 -05:00
Scott Lahteine
628dcbc764
extruder_multiplier => flow_percentage
2016-08-18 22:13:47 -05:00
Scott Lahteine
d63b8e2b2b
Additional details for I2C_SLAVE_ADDRESS
2016-08-15 19:27:53 -07:00
Scott Lahteine
bd928a69ec
Add request, capture, flush to TWIBus
2016-08-15 00:04:20 -07:00
Scott Lahteine
97e0aed304
Further refinements of TWIBus
2016-08-13 18:32:41 -07:00
Scott Lahteine
67f119d18b
Add an i2c request handler
2016-08-11 18:09:18 -07:00
Scott Lahteine
d6a7ca6553
Merge pull request #4584 from thinkyhead/rc_delta_cal_more
...
Use configured feedrates, center in DELTA_CALIBRATION_MENU
2016-08-11 14:04:05 -07:00
Scott Lahteine
52560e257f
Merge pull request #4595 from thinkyhead/rc_i2c_slave
...
Add support for i2c slave address
2016-08-11 12:39:26 -07:00
Scott Lahteine
cd496dd9bd
do_blocking_move_to can't be 'inline', takes const ref args
2016-08-11 12:05:55 -07:00
Scott Lahteine
dd75fca4d9
Make M155 / M156 a bit more flexible
2016-08-11 00:52:01 -07:00
Scott Lahteine
a99ecf71d8
Add support for i2c slave address
2016-08-10 23:30:35 -07:00
Scott Lahteine
b63d70b186
Fix serial output for MBL, M303
2016-08-10 18:49:52 -07:00
Scott Lahteine
45f67164b6
Simplify the delay in kill()
2016-08-08 21:49:34 -07:00
Scott Lahteine
367dad5902
Sanity check Z_DUAL_ENDSTOPS with DELTA
2016-08-07 17:08:41 -07:00
Scott Lahteine
7b2abe6fc8
Use steps_to_mm in extruder runout prevent
2016-08-07 00:28:52 -07:00
Scott Lahteine
d320065320
Within Marlin, maintain most feed rates in mm/s
2016-08-07 00:28:52 -07:00
Scott Lahteine
a00783c41f
Format probe stowed test code
2016-08-06 14:31:07 -07:00
AnHardt
f37e8a31d7
Make Allen Key Probe stow
...
by switching off the tests for the probe before the stow move.
2016-08-06 14:30:38 -07:00
Scott Lahteine
938e6d15c4
Patch up some flaws, here and there
2016-08-05 08:17:37 -07:00
Scott Lahteine
7e2bd9a233
Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT
2016-08-03 21:18:38 -07:00
Scott Lahteine
445458c221
Don't include zprobe_zoffset in do_probe_raise
2016-08-03 21:12:02 -07:00
Scott Lahteine
b73203a0b7
Move some includes around to uncover missing deps
2016-08-02 19:37:46 -07:00
Scott Lahteine
0f030aface
Merge pull request #4503 from AnHardt/fix-retract
...
Correct typo in retract()
2016-08-02 15:04:55 -07:00
Scott Lahteine
330f82971b
Buzzer requires BEEPER_PIN
2016-08-02 14:05:37 -07:00
AnHardt
39c4603598
Correct typo in retract.
2016-08-02 21:06:08 +02:00
Scott Lahteine
6eed37aafb
Merge pull request #4486 from thinkyhead/rc_pid_add_extrusion_rate_off
...
PID_EXTRUSION_SCALING, disabled by default
2016-07-31 18:23:51 -07:00
Scott Lahteine
4bf3526d00
Merge pull request #4463 from thinkyhead/rc_azteeg_x3_eeb
...
Wrangle RAMPS variants and derivatives
2016-07-31 18:22:49 -07:00
Scott Lahteine
63fd1f49a6
PID_EXTRUSION_SCALING, disabled by default
2016-07-31 17:49:34 -07:00
Scott Lahteine
f388beafa1
Merge pull request #4476 from otvald/RCBugFix
...
FIX for endstop adjustemt on delta is offset
2016-07-31 01:09:54 -07:00
Thomas Otvald Jensen
fe059f1221
During homing, line_to_axis_pos will make a path which moves across the
...
endstop trigger point. The move is stopped at endstop, so current_position
should also be adjusted to reflect this!
Caused error in subsequent call in endstop adjustment, since the movement
would assume a wrong starting position.
2016-07-30 16:50:31 +02:00
esenapaj
bd73e6d3c8
Fix for PR #4452 (Additional heater-state output changes)
...
・Add missing ';'
2016-07-30 22:49:30 +09:00
Scott Lahteine
bdac2eb13a
Don't set non-existent SLED_PIN
2016-07-30 04:17:21 -07:00
Scott Lahteine
8e2f095dde
Merge pull request #4456 from jbrazio/speaker-type3
...
Improvement to non-blocking speaker
2016-07-30 04:07:08 -07:00
