3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-12-15 15:01:44 +00:00
Code Issues Releases Wiki Activity
13,472 Commits 21 Branches 81 Tags 2 GiB
4762dfe797
Commit Graph

162 Commits

Author SHA1 Message Date
Scott Lahteine
d556dc1865
Fix and improve EEPROM storage (#12054) 
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
 2018-10-10 09:45:20 -05:00
Roxy-3D
0780913848 IDEX Improvements (#11848) 2018-09-17 01:06:22 -05:00
Scott Lahteine
1718eff54a Code changes supporting up to 6 extruders 2018-09-16 22:32:53 -05:00
Holger Müller
1a6f2b29b8 Add support for Triple-Z steppers/endstops 2018-09-16 00:35:58 -05:00
Scott Lahteine
d882717d98
Save some PROGMEM with constexpr (#11798) 
When possible, make `active_extruder` a `constexpr` to save some PROGMEM.
 2018-09-10 23:09:26 -05:00
Sebastianv650
7e8c073fba Fix extruder stops extruding with LA (#11758) 2018-09-09 00:04:14 -05:00
Scott Lahteine
d1ceaf5550
[2.0.x] Followup to IDEX changes (#11707) 2018-09-03 23:15:31 -05:00
Roxy-3D
7680b64aa6
IDEX clean up (#11690) 2018-09-02 10:18:59 -05:00
Dave Johnson
c64199941e Compile only selected PIO environment (#11519) 2018-08-14 03:28:52 -05:00
Giuliano
e85feb2545 [2.0.x] Better timing handling (#11461) 2018-08-06 23:13:36 -05:00
Scott Lahteine
aa4cd2e861 Eliminate stepper.* signed/unsigned warnings 2018-06-27 23:10:51 -05:00
Eduardo José Tagle
edb21f349a Fix stepper/planner block handling, race conditions (#11098) 
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
 2018-06-27 18:11:16 -05:00
etagle
5b49fccf80 Add stepper driver DIR delay configuration option 
...and recommended pulse width configuration for A4988
 2018-06-26 13:28:04 -05:00
Scott Lahteine
99591dc20c
Filter endstops state at all times (#11066) 2018-06-21 20:14:16 -05:00
etagle
a215725df6 Fix stepper pulse timing 
Always honor minimum period on stepper pulse generation, and fix timing calculations

Signed-off-by: etagle <ejtagle@hotmail.com>
 2018-06-12 21:34:24 -05:00
Scott Lahteine
0d79128c8d Localize stepper-specific defines 2018-06-12 21:16:54 -05:00
Scott Lahteine
4dbec774b5 HAL_*_TIMER_RATE => *_TIMER_RATE 2018-06-12 16:39:12 -05:00
etagle
6f14bcaa3e Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping 
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
 2018-06-10 16:02:47 -05:00
etagle
39a7e7720d Adaptive multiaxis step smoothing 
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
 2018-06-10 16:02:47 -05:00
Scott Lahteine
3701869e6c Add HAL_timer_start for AVR, use stepper timer to time pulses 2018-06-09 22:30:13 -05:00
Scott Lahteine
ad8d3150aa Cleanup for dual endstops homing 2018-06-03 00:34:29 -05:00
Eduardo José Tagle
d3c02410a8 [2.0.x] Small assorted collection of fixes and improvements (#10911) 
* Misc fixes and improvements

- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
  Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).

* Set position immediately when possible
 2018-06-01 19:02:22 -05:00
Scott Lahteine
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE (#10885) 2018-05-28 19:34:08 -05:00
Scott Lahteine
0ca9db7051 Correct HOTENDS for SWITCHING_EXTRUDER 2018-05-27 23:22:48 -05:00
Eduardo José Tagle
7b9f0302d4 Fix Bresenham rounding errors, add link to article (#10871) 2018-05-27 01:49:59 -05:00
Scott Lahteine
2566342979 Adjust some commentary 2018-05-27 00:10:25 -05:00
Scott Lahteine
6775a16c97 Fix switching extruder stepping with LA 2018-05-26 19:07:01 -05:00
Scott Lahteine
aaaf09bda2 BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION 2018-05-26 18:33:51 -05:00
Scott Lahteine
01d37e00af
Fix up stepper ISR with linear advance timing (#10853) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-26 01:00:13 -05:00
Scott Lahteine
7261f48872 Fix reset of endstops and move state 2018-05-24 19:33:36 -05:00
Scott Lahteine
50fa8e01c1 Minor optimization of axis_did_move bits 2018-05-24 19:08:07 -05:00
Scott Lahteine
f28e366b77 Followup for core endstops 2018-05-24 03:02:57 -05:00
Scott Lahteine
9644d56b42 Patches for core motion tests 2018-05-24 00:49:01 -05:00
Scott Lahteine
3e3789da85
Regression: Endstops Core compatibility (#10823) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-23 03:45:25 -05:00
Scott Lahteine
4b2f6e3b2b
[2.0.x] Add endstop noise filter (#10796) 2018-05-21 15:51:38 -05:00
Scott Lahteine
435ecb6b67 Followup to stepper/planner refactor 2018-05-20 23:13:38 -05:00
etagle
569df3fc0c Fix interrupt-based endstop detection 
- Also implemented real endstop reading on interrupt.
 2018-05-20 07:10:24 -05:00
etagle
a11eb50a3e Refactor and optimize Stepper/Planner 
Better encapsulation and considerably reduce stepper jitter
 2018-05-20 06:23:58 -05:00
Scott Lahteine
7dc03ce721 Simplified fix for babystep pulse width 
Alternative to the apparently superfluous double delay
 2018-05-19 21:00:08 -05:00
Scott Lahteine
65270d6a96 Fix LIN_ADVANCE + SWITCHING_EXTRUDER 
Followup to #10656
 2018-05-19 18:32:00 -05:00
Bob Kuhn
9ad42d6617 add delay between pulse edges (#10778) 2018-05-19 17:12:16 -05:00
Scott Lahteine
ba4c32eec5 Followup to _AXIS patch 2018-05-13 10:43:35 -05:00
Scott Lahteine
d9154ebdf6 Followup to math patch 2018-05-13 09:30:27 -05:00
Scott Lahteine
883b0c9880
Convert custom maths to inlines (#10728) 2018-05-13 08:10:08 -05:00
Scott Lahteine
08e36e264e Apply _AXIS macro 2018-05-13 06:51:01 -05:00
Scott Lahteine
8f8c6a9bc4
Move get_axis_position_mm to Planner (#10718) 2018-05-12 09:59:11 -05:00
Scott Lahteine
a1062eec5b
Better handling of DELAY_NS and DELAY_US (#10716) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-12 08:34:04 -05:00
Scott Lahteine
3614e6ce0f Fix Switching Extruder with Linear Advance 2018-05-12 02:26:14 -05:00
Scott Lahteine
306f0f2135
Move Stepper::synchronize to Planner (#10713) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-12 01:38:02 -05:00
Scott Lahteine
722aba77f3
Fix LIN_ADVANCE + SWITCHING_EXTRUDER stepper directions (#10656) 2018-05-09 14:36:09 -05:00
Scott Lahteine
0436e16fb2 Apply shorthand Assembler macros 2018-05-08 10:08:54 -05:00
Scott Lahteine
af1950a63e Improve sync of stepper positions 2018-05-06 01:24:14 -05:00
Scott Lahteine
0c23792344 Apply int32_t to stepper 2018-05-05 18:21:03 -05:00
Eduardo José Tagle
0c428a66d9 Proper AVR preemptive interrupt handling (#10496) 
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
 2018-04-23 22:05:07 -05:00
Scott Lahteine
36b97bde9f clear_block_buffer, kill_current_block in quick_stop 2018-04-13 22:04:53 -05:00
Eduardo José Tagle
57a899a412 [2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373) 2018-04-11 18:13:42 -05:00
etagle
a29adde5c0 Implement BEZIER_JERK_CONTROL 
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
 2018-04-07 21:03:28 -05:00
Scott Lahteine
7d8a46519f Output ABC for delta stepper counts 2018-03-31 20:13:32 -05:00
Scott Lahteine
1cb810ff1c
[2.0.x] Automatically reset stepper timeout (#10179) 
* Automatically reset stepper timeout in manage_inactivity

Any code that adds moves to the planner can skip resetting the stepper timeout. We can let `idle` / `manage_inactivity` reset the timer whenever it detects any moves in the planner.

* blocks_queued => has_blocks_queued
 2018-03-21 19:30:06 -05:00
Scott Lahteine
48d7036874 Consolidate smart stepper driver initialization 2018-03-19 22:05:16 -05:00
Scott Lahteine
eaefc1e410
Add CorePQ support for BABYSTEPPING (#10155) 2018-03-19 02:51:40 -05:00
Scott Lahteine
51bf3c9503 Fix E direction for MK2_MULTIPLEXER with LIN_ADVANCE 2018-03-14 07:56:18 -05:00
Scott Lahteine
e7570f3195 Improve TMC config organization, naming 2018-03-14 00:18:41 -05:00
Scott Lahteine
751785fc97 Followup to recent patches 
- `M666` is static, not inline
- Disambiguate some stepper macros
 2018-03-10 21:41:17 -06:00
Scott Lahteine
16a8edc5f0 Add more delay before pulse off in Linear Advance ISR 
A capital idea from https://github.com/MarlinFirmware/Marlin/pull/9914#issuecomment-371614153
 2018-03-09 05:26:29 -06:00
Scott Lahteine
98d48fc731 Followup to HAL_timer_restrain 
Followup to #9985
 2018-03-07 22:18:37 -06:00
Chris Pepper
a1a88ebabc HAL function to ensure min stepper interrupt interval (#9985) 2018-03-07 17:53:25 -06:00
Scott Lahteine
e5ec793f7e Wrap stepper indirection macros 2018-03-07 05:42:45 -06:00
Sebastianv650
5b85464791 Fix for LA (#9964) 
Missed in the original LA 1.5 PR: eISR has to use a local copy of
current_block->use_advance_lead because it might still run wenn the last
block has been set to NULL.
 2018-03-07 05:33:13 -06:00
Scott Lahteine
ca0def766e LIN_ADVANCE single stepper optimization 2018-03-06 19:26:54 -06:00
Scott Lahteine
8291ae34f2 Support duplication mode in LIN_ADVANCE 2018-03-06 19:12:23 -06:00
Scott Lahteine
0dd1c4458d
Put more code between pulse start and stop (#9959) 2018-03-05 23:06:57 -06:00
Scott Lahteine
07ae23fe14 No pulse delay on last e_steps in advance isr 2018-03-04 15:06:31 -06:00
Scott Lahteine
ed758de80d tweak comment in stepper.cpp 2018-03-04 04:03:23 -06:00
Scott Lahteine
6d7f4f84e2
Add board MKS_BASE_HEROIC (#9926) 
Followup to #9008

- Don't define micro-stepping pins for boards that lack them.
- Allow setting of 128 microsteps with `M350`.
 2018-03-03 23:14:52 -06:00
Sebastianv650
cb4cb86d80 Useless line removed (#9814) 
nextAdvanceISR is set in the next if structure in every possible
situation, so it's useless to set it once more before.
 2018-02-25 21:20:37 -06:00
UtterlyD
813f9f3082 [bugfix_2.0.x] - LIN_ADVANCE V1.5 stepper.cpp (#9797) 
Removal of obsolete (i) from port of LIN_ADVANCE from V1.1.x to V2..0.x.
 2018-02-24 16:37:23 -06:00
Scott Lahteine
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 (#9712) 2018-02-23 00:53:29 -06:00
Scott Lahteine
3d1692d1fd Fix X2 enable with X_DUAL_STEPPER_DRIVERS 
From #9286
 2018-02-18 22:50:47 -06:00
Scott Lahteine
03d790451f
[2.0.x] HAL timer set/get count => set/get compare (#9581) 
To reduce confusion over the current timer count vs. the compare (aka "top") value. Caution: this re-uses the function name, changing its meaning.
 2018-02-10 20:42:00 -06:00
Scott Lahteine
d168ee9bed Drop leveling include from steppers.cpp 2018-02-08 01:32:19 -06:00
Scott Lahteine
887664aa61 Restore broken Dual X Carriage 2018-01-20 15:08:50 -06:00
Scott Lahteine
50366b00d5 Tweak cleaning buffer / SD finished command 2017-12-24 20:35:05 -06:00
Scott Lahteine
8df5955da4 Revert "Reset timer count before first block step" 
This reverts commit 5cf6a062e3.
 2017-12-17 02:37:35 -06:00
teemuatlut
0cd1e91056 [2.0.x] TMC driver update (#8769) 2017-12-15 15:03:14 -06:00
Scott Lahteine
cf2193c07f Comment, fix filament width sensor 2017-12-13 02:32:34 -06:00
Scott Lahteine
73e32925e4 References are better for array args 2017-12-11 00:27:06 -06:00
Scott Lahteine
5cf6a062e3 Reset timer count before first block step 2017-12-10 18:38:53 -06:00
Scott Lahteine
82ef6b5242 Add an option to specify "pulse" timer 2017-12-10 18:38:53 -06:00
Scott Lahteine
4fa65a5c25 TCNT0 => HAL_timer_get_current_count 
Fix #8710
 2017-12-08 22:35:28 -06:00
Scott Lahteine
85c6ffbe0d Discard all "continued" blocks on interrupted move 2017-12-08 02:32:58 -06:00
Scott Lahteine
9898b96992 No lcd_map_control flag in quick_stop 2017-12-06 22:23:34 -06:00
Scott Lahteine
840289e7cc Use block cleaning instead of split flag 2017-12-06 22:22:58 -06:00
Scott Lahteine
2fde60da12 Changes for parity with 1.1.x 2017-12-06 21:50:54 -06:00
Scott Lahteine
6040d4080e Cleanup stepper ISR. Allow cleaning for endstops. 2017-12-06 21:23:37 -06:00
Scott Lahteine
000b3b3117 Comment/cleanup of motion code 2017-12-02 01:09:55 -06:00
Scott Lahteine
1d4571b88d Dependency adjustments 2017-11-19 15:43:38 -06:00
Scott Lahteine
2246316605 Fix name collision. timer_t => hal_timer_t 2017-11-05 19:31:07 -06:00
Scott Lahteine
723f2a77f6 Implement support for Dual X and Y endstops 2017-10-29 18:56:04 -05:00
Thomas Moore
9e699811d2 Make LPC1768 pinmapping not specific to Re-ARM (#8063) 
* Merging early because of build failures.  See #8105

* Make LPC1768 pinmapping not specific to Re-ARM

* Add HAL_PIN_TYPE and LPC1768 pin features

* M43 Updates

* Move pin map into pinsDebug_LPC1768.h

* Incorporate comments and M226

* Fix persistent store compilation issues

* Update pin features

* Update MKS SBASE pins

* Use native LPC1768 pin numbers in M42, M43, and M226
 2017-10-26 13:37:26 -05:00