/** * Marlin 3D Printer Firmware * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ /** * Azteeg X5 MINI pin assignments */ #ifndef LPC1769 #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." #endif #define BOARD_NAME "Azteeg X5 MINI WIFI" #define BOARD_WEBSITE_URL "http://www.panucatt.com/azteeg_X5_mini_reprap_3d_printer_controller_p/ax5mini.htm" // // LED // #define LED_PIN P1_18 // // Servos // #define SERVO0_PIN P1_29 // // Limit Switches // #define X_STOP_PIN P1_24 #define Y_STOP_PIN P1_26 #define Z_STOP_PIN P1_28 #ifndef FILWIDTH_PIN #define FILWIDTH_PIN P2_04 #endif // // Steppers // #define X_STEP_PIN P2_01 #define X_DIR_PIN P0_11 #define X_ENABLE_PIN P0_10 #define Y_STEP_PIN P2_02 #define Y_DIR_PIN P0_20 #define Y_ENABLE_PIN P0_19 #define Z_STEP_PIN P2_03 #define Z_DIR_PIN P0_22 #define Z_ENABLE_PIN P0_21 #define E0_STEP_PIN P2_00 #define E0_DIR_PIN P0_05 #define E0_ENABLE_PIN P0_04 // // DIGIPOT slave addresses // #define DIGIPOT_I2C_ADDRESS_A 0x58 // shifted slave address for first DIGIPOT (0x58 <- 0x2C << 1) #define DIGIPOT_I2C_ADDRESS_B 0x5C // shifted slave address for second DIGIPOT (0x5C <- 0x2E << 1) // // Temperature Sensors // 3.3V max when defined as an analog input // #define TEMP_BED_PIN 0 // A0 (TH1) #define TEMP_0_PIN 1 // A1 (TH2) // // Heaters / Fans // #define HEATER_BED_PIN P2_07 #define HEATER_0_PIN P2_05 #ifndef FAN_PIN #define FAN_PIN P0_26 #endif #define FAN1_PIN P1_25 // // Display // #if ENABLED(ULTRA_LCD) #if ENABLED(CR10_STOCKDISPLAY) // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. // Requires REVERSE_ENCODER_DIRECTION in Configuration.h #define BEEPER_PIN P2_11 // J3-3 & AUX-4 #define BTN_EN1 P0_16 // J3-7 & AUX-4 #define BTN_EN2 P1_23 // J3-5 & AUX-4 #define BTN_ENC P3_25 // J3-4 & AUX-4 #define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS) #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) #else #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 #define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3 #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3 #define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #elif DISABLED(NEWPANEL) //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 #endif #if ENABLED(VIKI2) || ENABLED(miniVIKI) //#define LCD_SCREEN_ROT_180 #define BEEPER_PIN P1_30 // (37) may change if cable changes #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #define DOGLCD_SCK SCK_PIN #define DOGLCD_MOSI MOSI_PIN #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes #else #if ENABLED(ULTIPANEL) #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 #endif #define BEEPER_PIN P1_30 // (37) not 5V tolerant #define DOGLCD_CS P0_16 // (16) #endif #if ENABLED(MINIPANEL) // GLCD features //#define LCD_CONTRAST 190 // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 #endif #endif #endif // ULTRA_LCD // // SD Support // //#define USB_SD_DISABLED // Disable host access to SD card as mass storage device through USB //#define USB_SD_ONBOARD // Enable host access to SD card as mass storage device through USB //#define LPC_SD_LCD // Marlin uses the SD drive attached to the LCD #define LPC_SD_ONBOARD // Marlin uses the SD drive on the control board. There is no SD detect pin // for the onboard card. Init card from LCD menu or send M21 whenever printer // is powered on to enable SD access. #if ENABLED(LPC_SD_LCD) #define SCK_PIN P0_15 #define MISO_PIN P0_17 #define MOSI_PIN P0_18 #define SS_PIN P1_23 // Chip select for SD card used by Marlin #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #elif ENABLED(LPC_SD_ONBOARD) #if ENABLED(USB_SD_ONBOARD) // When sharing the SD card with a PC we want the menu options to // mount/unmount the card and refresh it. So we disable card detect. #define SHARED_SD_CARD #undef SD_DETECT_PIN // there is also no detect pin for the onboard card #endif #define SCK_PIN P0_07 #define MISO_PIN P0_08 #define MOSI_PIN P0_09 #define SS_PIN P0_06 // Chip select for SD card used by Marlin #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #endif