/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ /** * planner.h * * Buffer movement commands and manage the acceleration profile plan * * Derived from Grbl * Copyright (c) 2009-2011 Simen Svale Skogsrud */ #ifndef PLANNER_H #define PLANNER_H #include "types.h" #include "enum.h" #include "Marlin.h" #if HAS_ABL #include "vector_3.h" #endif enum BlockFlagBit { // Recalculate trapezoids on entry junction. For optimization. BLOCK_BIT_RECALCULATE, // Nominal speed always reached. // i.e., The segment is long enough, so the nominal speed is reachable if accelerating // from a safe speed (in consideration of jerking from zero speed). BLOCK_BIT_NOMINAL_LENGTH, // Start from a halt at the start of this block, respecting the maximum allowed jerk. BLOCK_BIT_START_FROM_FULL_HALT, // The block is busy BLOCK_BIT_BUSY }; enum BlockFlag { BLOCK_FLAG_RECALCULATE = _BV(BLOCK_BIT_RECALCULATE), BLOCK_FLAG_NOMINAL_LENGTH = _BV(BLOCK_BIT_NOMINAL_LENGTH), BLOCK_FLAG_START_FROM_FULL_HALT = _BV(BLOCK_BIT_START_FROM_FULL_HALT), BLOCK_FLAG_BUSY = _BV(BLOCK_BIT_BUSY) }; /** * struct block_t * * A single entry in the planner buffer. * Tracks linear movement over multiple axes. * * The "nominal" values are as-specified by gcode, and * may never actually be reached due to acceleration limits. */ typedef struct { uint8_t flag; // Block flags (See BlockFlag enum above) unsigned char active_extruder; // The extruder to move (if E move) // Fields used by the Bresenham algorithm for tracing the line int32_t steps[NUM_AXIS]; // Step count along each axis uint32_t step_event_count; // The number of step events required to complete this block #if ENABLED(MIXING_EXTRUDER) uint32_t mix_event_count[MIXING_STEPPERS]; // Scaled step_event_count for the mixing steppers #endif int32_t accelerate_until, // The index of the step event on which to stop acceleration decelerate_after, // The index of the step event on which to start decelerating acceleration_rate; // The acceleration rate used for acceleration calculation uint8_t direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h) // Advance extrusion #if ENABLED(LIN_ADVANCE) bool use_advance_lead; uint32_t abs_adv_steps_multiplier8; // Factorised by 2^8 to avoid float #endif // Fields used by the motion planner to manage acceleration float nominal_speed, // The nominal speed for this block in mm/sec entry_speed, // Entry speed at previous-current junction in mm/sec max_entry_speed, // Maximum allowable junction entry speed in mm/sec millimeters, // The total travel of this block in mm acceleration; // acceleration mm/sec^2 // Settings for the trapezoid generator uint32_t nominal_rate, // The nominal step rate for this block in step_events/sec initial_rate, // The jerk-adjusted step rate at start of block final_rate, // The minimal rate at exit acceleration_steps_per_s2; // acceleration steps/sec^2 #if FAN_COUNT > 0 uint16_t fan_speed[FAN_COUNT]; #endif #if ENABLED(BARICUDA) uint8_t valve_pressure, e_to_p_pressure; #endif uint32_t segment_time_us; } block_t; #define BLOCK_MOD(n) ((n)&(BLOCK_BUFFER_SIZE-1)) class Planner { public: /** * A ring buffer of moves described in steps */ static block_t block_buffer[BLOCK_BUFFER_SIZE]; static volatile uint8_t block_buffer_head, // Index of the next block to be pushed block_buffer_tail; #if ENABLED(DISTINCT_E_FACTORS) static uint8_t last_extruder; // Respond to extruder change #endif static int16_t flow_percentage[EXTRUDERS]; // Extrusion factor for each extruder static float e_factor[EXTRUDERS], // The flow percentage and volumetric multiplier combine to scale E movement filament_size[EXTRUDERS], // diameter of filament (in millimeters), typically around 1.75 or 2.85, 0 disables the volumetric calculations for the extruder volumetric_area_nominal, // Nominal cross-sectional area volumetric_multiplier[EXTRUDERS]; // Reciprocal of cross-sectional area of filament (in mm^2). Pre-calculated to reduce computation in the planner // May be auto-adjusted by a filament width sensor static float max_feedrate_mm_s[XYZE_N], // Max speeds in mm per second axis_steps_per_mm[XYZE_N], steps_to_mm[XYZE_N]; static uint32_t max_acceleration_steps_per_s2[XYZE_N], max_acceleration_mm_per_s2[XYZE_N]; // Use M201 to override static uint32_t min_segment_time_us; // Use 'M205 B<µs>' to override static float min_feedrate_mm_s, acceleration, // Normal acceleration mm/s^2 DEFAULT ACCELERATION for all printing moves. M204 SXXXX retract_acceleration, // Retract acceleration mm/s^2 filament pull-back and push-forward while standing still in the other axes M204 TXXXX travel_acceleration, // Travel acceleration mm/s^2 DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX max_jerk[XYZE], // The largest speed change requiring no acceleration min_travel_feedrate_mm_s; #if HAS_LEVELING static bool leveling_active; // Flag that bed leveling is enabled #if ABL_PLANAR static matrix_3x3 bed_level_matrix; // Transform to compensate for bed level #endif #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) static float z_fade_height, inverse_z_fade_height; #endif #endif #if ENABLED(LIN_ADVANCE) static float extruder_advance_k, advance_ed_ratio; #endif private: /** * The current position of the tool in absolute steps * Recalculated if any axis_steps_per_mm are changed by gcode */ static int32_t position[NUM_AXIS]; /** * Speed of previous path line segment */ static float previous_speed[NUM_AXIS]; /** * Nominal speed of previous path line segment */ static float previous_nominal_speed; /** * Limit where 64bit math is necessary for acceleration calculation */ static uint32_t cutoff_long; #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) static float last_fade_z; #endif #if ENABLED(DISABLE_INACTIVE_EXTRUDER) /** * Counters to manage disabling inactive extruders */ static uint8_t g_uc_extruder_last_move[EXTRUDERS]; #endif // DISABLE_INACTIVE_EXTRUDER #ifdef XY_FREQUENCY_LIMIT // Used for the frequency limit #define MAX_FREQ_TIME_US (uint32_t)(1000000.0 / XY_FREQUENCY_LIMIT) // Old direction bits. Used for speed calculations static unsigned char old_direction_bits; // Segment times (in µs). Used for speed calculations static uint32_t axis_segment_time_us[2][3]; #endif #if ENABLED(ULTRA_LCD) volatile static uint32_t block_buffer_runtime_us; //Theoretical block buffer runtime in µs #endif public: /** * Instance Methods */ Planner(); void init(); /** * Static (class) Methods */ static void reset_acceleration_rates(); static void refresh_positioning(); FORCE_INLINE static void refresh_e_factor(const uint8_t e) { e_factor[e] = volumetric_multiplier[e] * flow_percentage[e] * 0.01; } // Manage fans, paste pressure, etc. static void check_axes_activity(); /** * Number of moves currently in the planner */ static uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block_buffer_tail + BLOCK_BUFFER_SIZE); } static bool is_full() { return (block_buffer_tail == BLOCK_MOD(block_buffer_head + 1)); } // Update multipliers based on new diameter measurements static void calculate_volumetric_multipliers(); FORCE_INLINE static void set_filament_size(const uint8_t e, const float &v) { filament_size[e] = v; // make sure all extruders have some sane value for the filament size for (uint8_t i = 0; i < COUNT(filament_size); i++) if (!filament_size[i]) filament_size[i] = DEFAULT_NOMINAL_FILAMENT_DIA; } #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) /** * Get the Z leveling fade factor based on the given Z height, * re-calculating only when needed. * * Returns 1.0 if planner.z_fade_height is 0.0. * Returns 0.0 if Z is past the specified 'Fade Height'. */ inline static float fade_scaling_factor_for_z(const float &rz) { static float z_fade_factor = 1.0; if (z_fade_height) { if (rz >= z_fade_height) return 0.0; if (last_fade_z != rz) { last_fade_z = rz; z_fade_factor = 1.0 - rz * inverse_z_fade_height; } return z_fade_factor; } return 1.0; } FORCE_INLINE static void force_fade_recalc() { last_fade_z = -999.999; } FORCE_INLINE static void set_z_fade_height(const float &zfh) { z_fade_height = zfh > 0 ? zfh : 0; inverse_z_fade_height = RECIPROCAL(z_fade_height); force_fade_recalc(); } FORCE_INLINE static bool leveling_active_at_z(const float &rz) { return !z_fade_height || rz < z_fade_height; } #else FORCE_INLINE static float fade_scaling_factor_for_z(const float &rz) { UNUSED(rz); return 1.0; } FORCE_INLINE static bool leveling_active_at_z(const float &rz) { UNUSED(rz); return true; } #endif #if PLANNER_LEVELING #define ARG_X float rx #define ARG_Y float ry #define ARG_Z float rz /** * Apply leveling to transform a cartesian position * as it will be given to the planner and steppers. */ static void apply_leveling(float &rx, float &ry, float &rz); static void apply_leveling(float raw[XYZ]) { apply_leveling(raw[X_AXIS], raw[Y_AXIS], raw[Z_AXIS]); } static void unapply_leveling(float raw[XYZ]); #else #define ARG_X const float &rx #define ARG_Y const float &ry #define ARG_Z const float &rz #endif /** * Planner::_buffer_line * * Add a new direct linear movement to the buffer. * * Leveling and kinematics should be applied ahead of this. * * a,b,c,e - target position in mm or degrees * fr_mm_s - (target) speed of the move (mm/s) * extruder - target extruder */ static void _buffer_line(const float &a, const float &b, const float &c, const float &e, float fr_mm_s, const uint8_t extruder); static void _set_position_mm(const float &a, const float &b, const float &c, const float &e); /** * Add a new linear movement to the buffer. * The target is NOT translated to delta/scara * * Leveling will be applied to input on cartesians. * Kinematic machines should call buffer_line_kinematic (for leveled moves). * (Cartesians may also call buffer_line_kinematic.) * * rx,ry,rz,e - target position in mm or degrees * fr_mm_s - (target) speed of the move (mm/s) * extruder - target extruder */ static FORCE_INLINE void buffer_line(ARG_X, ARG_Y, ARG_Z, const float &e, const float &fr_mm_s, const uint8_t extruder) { #if PLANNER_LEVELING && IS_CARTESIAN apply_leveling(rx, ry, rz); #endif _buffer_line(rx, ry, rz, e, fr_mm_s, extruder); } /** * Add a new linear movement to the buffer. * The target is cartesian, it's translated to delta/scara if * needed. * * cart - x,y,z,e CARTESIAN target in mm * fr_mm_s - (target) speed of the move (mm/s) * extruder - target extruder */ static FORCE_INLINE void buffer_line_kinematic(const float cart[XYZE], const float &fr_mm_s, const uint8_t extruder) { #if PLANNER_LEVELING float raw[XYZ] = { cart[X_AXIS], cart[Y_AXIS], cart[Z_AXIS] }; apply_leveling(raw); #else const float * const raw = cart; #endif #if IS_KINEMATIC inverse_kinematics(raw); _buffer_line(delta[A_AXIS], delta[B_AXIS], delta[C_AXIS], cart[E_AXIS], fr_mm_s, extruder); #else _buffer_line(raw[X_AXIS], raw[Y_AXIS], raw[Z_AXIS], cart[E_AXIS], fr_mm_s, extruder); #endif } /** * Set the planner.position and individual stepper positions. * Used by G92, G28, G29, and other procedures. * * Multiplies by axis_steps_per_mm[] and does necessary conversion * for COREXY / COREXZ / COREYZ to set the corresponding stepper positions. * * Clears previous speed values. */ static FORCE_INLINE void set_position_mm(ARG_X, ARG_Y, ARG_Z, const float &e) { #if PLANNER_LEVELING && IS_CARTESIAN apply_leveling(rx, ry, rz); #endif _set_position_mm(rx, ry, rz, e); } static void set_position_mm_kinematic(const float position[NUM_AXIS]); static void set_position_mm(const AxisEnum axis, const float &v); static FORCE_INLINE void set_z_position_mm(const float &z) { set_position_mm(Z_AXIS, z); } static FORCE_INLINE void set_e_position_mm(const float &e) { set_position_mm(AxisEnum(E_AXIS), e); } /** * Sync from the stepper positions. (e.g., after an interrupted move) */ static void sync_from_steppers(); /** * Does the buffer have any blocks queued? */ static bool blocks_queued() { return (block_buffer_head != block_buffer_tail); } /** * "Discards" the block and "releases" the memory. * Called when the current block is no longer needed. */ static void discard_current_block() { if (blocks_queued()) block_buffer_tail = BLOCK_MOD(block_buffer_tail + 1); } /** * The current block. NULL if the buffer is empty. * This also marks the block as busy. */ static block_t* get_current_block() { if (blocks_queued()) { block_t* block = &block_buffer[block_buffer_tail]; #if ENABLED(ULTRA_LCD) block_buffer_runtime_us -= block->segment_time_us; // We can't be sure how long an active block will take, so don't count it. #endif SBI(block->flag, BLOCK_BIT_BUSY); return block; } else { #if ENABLED(ULTRA_LCD) clear_block_buffer_runtime(); // paranoia. Buffer is empty now - so reset accumulated time to zero. #endif return NULL; } } #if ENABLED(ULTRA_LCD) static uint16_t block_buffer_runtime() { CRITICAL_SECTION_START millis_t bbru = block_buffer_runtime_us; CRITICAL_SECTION_END // To translate µs to ms a division by 1000 would be required. // We introduce 2.4% error here by dividing by 1024. // Doesn't matter because block_buffer_runtime_us is already too small an estimation. bbru >>= 10; // limit to about a minute. NOMORE(bbru, 0xFFFFul); return bbru; } static void clear_block_buffer_runtime(){ CRITICAL_SECTION_START block_buffer_runtime_us = 0; CRITICAL_SECTION_END } #endif #if ENABLED(AUTOTEMP) static float autotemp_min, autotemp_max, autotemp_factor; static bool autotemp_enabled; static void getHighESpeed(); static void autotemp_M104_M109(); #endif private: /** * Get the index of the next / previous block in the ring buffer */ static int8_t next_block_index(int8_t block_index) { return BLOCK_MOD(block_index + 1); } static int8_t prev_block_index(int8_t block_index) { return BLOCK_MOD(block_index - 1); } /** * Calculate the distance (not time) it takes to accelerate * from initial_rate to target_rate using the given acceleration: */ static float estimate_acceleration_distance(const float &initial_rate, const float &target_rate, const float &accel) { if (accel == 0) return 0; // accel was 0, set acceleration distance to 0 return (sq(target_rate) - sq(initial_rate)) / (accel * 2); } /** * Return the point at which you must start braking (at the rate of -'acceleration') if * you start at 'initial_rate', accelerate (until reaching the point), and want to end at * 'final_rate' after traveling 'distance'. * * This is used to compute the intersection point between acceleration and deceleration * in cases where the "trapezoid" has no plateau (i.e., never reaches maximum speed) */ static float intersection_distance(const float &initial_rate, const float &final_rate, const float &accel, const float &distance) { if (accel == 0) return 0; // accel was 0, set intersection distance to 0 return (accel * 2 * distance - sq(initial_rate) + sq(final_rate)) / (accel * 4); } /** * Calculate the maximum allowable speed at this point, in order * to reach 'target_velocity' using 'acceleration' within a given * 'distance'. */ static float max_allowable_speed(const float &accel, const float &target_velocity, const float &distance) { return SQRT(sq(target_velocity) - 2 * accel * distance); } static void calculate_trapezoid_for_block(block_t* const block, const float &entry_factor, const float &exit_factor); static void reverse_pass_kernel(block_t* const current, const block_t *next); static void forward_pass_kernel(const block_t *previous, block_t* const current); static void reverse_pass(); static void forward_pass(); static void recalculate_trapezoids(); static void recalculate(); }; #define PLANNER_XY_FEEDRATE() (min(planner.max_feedrate_mm_s[X_AXIS], planner.max_feedrate_mm_s[Y_AXIS])) extern Planner planner; #endif // PLANNER_H