mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-12-01 23:58:33 +00:00
91 lines
2.6 KiB
C
91 lines
2.6 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* MALYAN M200 pin assignments
|
|
*/
|
|
|
|
#ifndef __STM32F1__
|
|
#error "Oops! You must be compiling for STM32."
|
|
#endif
|
|
|
|
#define BOARD_NAME "MALYANM200"
|
|
|
|
// Enable EEPROM Emulation for this board
|
|
// This setting should probably be in configuration.h
|
|
// but it is literally the only board which uses it.
|
|
#define FLASH_EEPROM_EMULATION
|
|
|
|
#define SDSS SS_PIN
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN PB4
|
|
#define Y_MIN_PIN PA15
|
|
#define Z_MIN_PIN PB5
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
// X & Y enable are the same
|
|
#define X_STEP_PIN PB14
|
|
#define X_DIR_PIN PB15
|
|
#define X_ENABLE_PIN PA8
|
|
|
|
#define Y_STEP_PIN PB12
|
|
#define Y_DIR_PIN PB13
|
|
#define Y_ENABLE_PIN PA8
|
|
|
|
#define Z_STEP_PIN PB10
|
|
#define Z_DIR_PIN PB2
|
|
#define Z_ENABLE_PIN PB11
|
|
|
|
#define E0_STEP_PIN PB0
|
|
#define E0_DIR_PIN PC13
|
|
#define E0_ENABLE_PIN PB1
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PA0 // Analog Input (HOTEND0 thermistor)
|
|
#define TEMP_BED_PIN PA1 // Analog Input (BED thermistor)
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PB6 // HOTEND0 MOSFET
|
|
#define HEATER_BED_PIN PB7 // BED MOSFET
|
|
|
|
// FAN_PIN is commented out here because the M200 example
|
|
// Configuration_adv.h does NOT override E0_AUTO_FAN_PIN.
|
|
#ifndef FAN_PIN
|
|
//#define FAN_PIN PB8 // FAN1 header on board - PRINT FAN
|
|
#endif
|
|
#define FAN1_PIN PB3 // FAN2 header on board - CONTROLLER FAN
|
|
#define FAN2_PIN -1 // FAN3 header on board - EXTRUDER0 FAN
|
|
|
|
// This board has only the controller fan and the extruder fan
|
|
// If someone hacks to put a direct power fan on the controller, PB3 could
|
|
// be used as a separate print cooling fan.
|
|
#define ORIG_E0_AUTO_FAN_PIN PB8
|