3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-12-13 22:11:38 +00:00
Code Issues Releases Wiki Activity
09fa34a9e1
MarlinFirmware/Marlin/src/pins/pins_RAMPS_RE_ARM.h
Scott Lahteine 09fa34a9e1 Modernize configs
2017-10-09 16:18:10 -05:00

395 lines
12 KiB
C
Raw Blame History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Re-ARM with RAMPS v1.4 pin assignments
*
* Applies to the following boards:
*
* RAMPS_14_EFB (Hotend, Fan, Bed)
* RAMPS_14_EEB (Hotend0, Hotend1, Bed)
* RAMPS_14_EFF (Hotend, Fan0, Fan1)
* RAMPS_14_EEF (Hotend0, Hotend1, Fan)
* RAMPS_14_SF (Spindle, Controller Fan)
*
*/
//#if !defined(TARGET_LPC1768)
#if DISABLED(IS_REARM)
#error "Oops! Make sure you have Re-Arm selected."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "Re-ARM RAMPS 1.4"
#endif
#define LARGE_FLASH true
// unused
#define D57 57
#define D58 58
//
// Servos
//
#define SERVO0_PIN 11
#define SERVO1_PIN 6 // also on J5-1
#define SERVO2_PIN 5
#define SERVO3_PIN 4 // 5V output - PWM capable
//
// Limit Switches
//
#define X_MIN_PIN 3 //10k pullup to 3.3V, 1K series
#define X_MAX_PIN 2 //10k pullup to 3.3V, 1K series
#define Y_MIN_PIN 14 //10k pullup to 3.3V, 1K series
#define Y_MAX_PIN 15 //10k pullup to 3.3V, 1K series
#define Z_MIN_PIN 18 //10k pullup to 3.3V, 1K series
#define Z_MAX_PIN 19 //10k pullup to 3.3V, 1K series
//#define Z_PROBE_PIN 1 // AUX-1
//
// Steppers
//
#define X_STEP_PIN 54
#define X_DIR_PIN 55
#define X_ENABLE_PIN 38
#define Y_STEP_PIN 60
#define Y_DIR_PIN 61
#define Y_ENABLE_PIN 56
#define Z_STEP_PIN 46
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 62
#define E0_STEP_PIN 26
#define E0_DIR_PIN 28
#define E0_ENABLE_PIN 24
#define E1_STEP_PIN 36
#define E1_DIR_PIN 34
#define E1_ENABLE_PIN 30
#define E2_STEP_PIN 36
#define E2_DIR_PIN 34
#define E2_ENABLE_PIN 30
//
// Temperature Sensors
// 3.3V max when defined as an analog input
//
#define TEMP_0_PIN 0 //A0 (T0) - D67 - TEMP_0_PIN
#define TEMP_BED_PIN 1 //A1 (T1) - D68 - TEMP_BED_PIN
#define TEMP_1_PIN 2 //A2 (T2) - D69 - TEMP_1_PIN
#define TEMP_2_PIN 3 //A3 - D63 - J5-3 & AUX-2
#define TEMP_3_PIN 4 //A4 - D37 - BUZZER_PIN
//#define TEMP_4_PIN 5 //A5 - D49 - SD_DETECT_PIN
//#define ?? 6 //A6 - D0 - RXD0 - J4-4 & AUX-1
#define FILWIDTH_PIN 7 //A7 - D1 - TXD0 - J4-5 & AUX-1
//
// Augmentation for auto-assigning RAMPS plugs
//
#if DISABLED(IS_RAMPS_EEB) && DISABLED(IS_RAMPS_EEF) && DISABLED(IS_RAMPS_EFB) && DISABLED(IS_RAMPS_EFF) && DISABLED(IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
#if HOTENDS > 1
#if TEMP_SENSOR_BED
#define IS_RAMPS_EEB
#else
#define IS_RAMPS_EEF
#endif
#elif TEMP_SENSOR_BED
#define IS_RAMPS_EFB
#else
#define IS_RAMPS_EFF
#endif
#endif
//
// Heaters / Fans
//
#ifndef MOSFET_D_PIN
#define MOSFET_D_PIN -1
#endif
#ifndef RAMPS_D8_PIN
#define RAMPS_D8_PIN 8
#endif
#ifndef RAMPS_D9_PIN
#define RAMPS_D9_PIN 9
#endif
#ifndef RAMPS_D10_PIN
#define RAMPS_D10_PIN 10
#endif
#define HEATER_0_PIN RAMPS_D10_PIN
#if ENABLED(IS_RAMPS_EFB) // Hotend, Fan, Bed
#define FAN_PIN RAMPS_D9_PIN
#define HEATER_BED_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EEF) // Hotend, Hotend, Fan
#define HEATER_1_PIN RAMPS_D9_PIN
#define FAN_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EEB) // Hotend, Hotend, Bed
#define HEATER_1_PIN RAMPS_D9_PIN
#define HEATER_BED_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EFF) // Hotend, Fan, Fan
#define FAN_PIN RAMPS_D9_PIN
#define FAN1_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_SF) // Spindle, Fan
#define FAN_PIN RAMPS_D8_PIN
#else // Non-specific are "EFB" (i.e., "EFBF" or "EFBE")
#define FAN_PIN RAMPS_D9_PIN
#define HEATER_BED_PIN RAMPS_D8_PIN
#if HOTENDS == 1
#define FAN1_PIN MOSFET_D_PIN
#else
#define HEATER_1_PIN MOSFET_D_PIN
#endif
#endif
#ifndef FAN_PIN
#define FAN_PIN 4 // IO pin. Buffer needed
#endif
//
// Misc. Functions
//
#define LED_PIN 13
// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
#define FIL_RUNOUT_PIN 4
#define PS_ON_PIN 12
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector
#define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM
#endif
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE)
#if !defined(NUM_SERVOS) || NUM_SERVOS == 1 // must use servo connector
#undef SERVO1
#undef SERVO2
#undef SERVO3
#define SPINDLE_LASER_ENABLE_PIN 6 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 5
#endif
#endif
//
// Průša i3 MK2 Multiplexer Support
//
#define E_MUX0_PIN 0 // Z_CS_PIN
#define E_MUX1_PIN 1 // E0_CS_PIN
#define E_MUX2_PIN 63 // E1_CS_PIN
/**
* LCD / Controller
*
* All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required.
*/
/**
* Smart LCD adapter
*
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
* is needed to pick up 5V for the EXP1 connection.
*
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
* on the LCD display during accesses of the SD card. The menus/code has been arranged so
* that the garbage/lines are erased immediately after the SD card accesses are completed.
*/
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN 37 // not 5V tolerant
#define BTN_EN1 31 // J3-2 & AUX-4
#define BTN_EN2 33 // J3-4 & AUX-4
#define BTN_ENC 35 // J3-3 & AUX-4
#define SD_DETECT_PIN 49 // not 5V tolerant J3-1 & AUX-3
#define KILL_PIN 41 // J5-4 & AUX-4
#define LCD_PINS_RS 16 // J3-7 & AUX-4
#define LCD_SDSS 16 // J3-7 & AUX-4
#define LCD_BACKLIGHT_PIN 16 // J3-7 & AUX-4 - only used on DOGLCD controllers
#define LCD_PINS_ENABLE 51 // (MOSI) J3-10 & AUX-3
#define LCD_PINS_D4 52 // (SCK) J3-9 & AUX-3
#define DOGLCD_A0 59 // J3-8 & AUX-2
#define DOGLCD_CS 63 // J5-3 & AUX-2
#ifdef ULTIPANEL
#define LCD_PINS_D5 71 // ENET_MDIO
#define LCD_PINS_D6 73 // ENET_RX_ER
#define LCD_PINS_D7 75 // ENET_RXD1
#endif
#if ENABLED(NEWPANEL)
#if ENABLED(REPRAPWORLD_KEYPAD)
#define SHIFT_OUT 51 // (MOSI) J3-10 & AUX-3
#define SHIFT_CLK 52 // (SCK) J3-9 & AUX-3
#define SHIFT_LD 49 // not 5V tolerant J3-1 & AUX-3
#endif
#else
//#define SHIFT_CLK 31 // J3-2 & AUX-4
//#define SHIFT_LD 33 // J3-4 & AUX-4
//#define SHIFT_OUT 35 // J3-3 & AUX-4
//#define SHIFT_EN 41 // J5-4 & AUX-4
#endif
#define SDCARD_SORT_ALPHA // Using SORT feature to keep one directory level in RAM
// When going up/down directory levels the SD card is
// accessed but the garbage/lines are removed when the
// LCD updates
#define SDSORT_LIMIT 256 // Maximum number of sorted items (10-256). Costs 27 bytes each.
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
#define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
// #define LCD_SCREEN_ROT_180
#undef BEEPER_PIN
#define BEEPER_PIN 37 // may change if cable changes
#define BTN_EN1 31 // J3-2 & AUX-4
#define BTN_EN2 33 // J3-4 & AUX-4
#define BTN_ENC 35 // J3-3 & AUX-4
#define SD_DETECT_PIN 49 // not 5V tolerant J3-1 & AUX-3
#define KILL_PIN 41 // J5-4 & AUX-4
#undef DOGLCD_CS
#define DOGLCD_CS 16
#undef LCD_BACKLIGHT_PIN //16 // J3-7 & AUX-4 - only used on DOGLCD controllers
#undef LCD_PINS_ENABLE //51 // (MOSI) J3-10 & AUX-3
#undef LCD_PINS_D4 //52 // (SCK) J3-9 & AUX-3
#undef LCD_PINS_D5 //59 // J3-8 & AUX-2
#define DOGLCD_A0 59 // J3-8 & AUX-2
#undef LCD_PINS_D6 //63 // J5-3 & AUX-2
#undef LCD_PINS_D7 // 6 // (SERVO1) J5-1 & SERVO connector
#define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN
#define STAT_LED_BLUE_PIN 63 // may change if cable changes
#define STAT_LED_RED_PIN 6 // may change if cable changes
#endif
//#define MISO_PIN 50 // system defined J3-10 & AUX-3
//#define MOSI_PIN 51 // system defined J3-10 & AUX-3
//#define SCK_PIN 52 // system defined J3-9 & AUX-3
//#define SS_PIN 53 // system defined J3-5 & AUX-3 - sometimes called SDSS
#if ENABLED(MINIPANEL)
// GLCD features
//#define LCD_CONTRAST 190
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#endif
#endif // ULTRA_LCD
//
// Ethernet pins
//
#ifndef ULTIPANEL
#define ENET_MDIO 71 // J12-4
#define ENET_RX_ER 73 // J12-6
#define ENET_RXD1 75 // J12-8
#endif
#define ENET_MOC 70 // J12-3
#define REF_CLK 72 // J12-5
#define ENET_RXD0 74 // J12-7
#define ENET_CRS 76 // J12-9
#define ENET_TX_EN 77 // J12-10
#define ENET_TXD0 78 // J12-11
#define ENET_TXD1 79 // J12-12
/**
* PWMS
*
* There are 6 PWMS. Each PWM can be assigned to one of two pins.
*
* SERVO2 does NOT have a PWM assigned to it.
*
* PWM1.1 DIO4 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM
* PWM1.1 DIO26 E0_STEP_PIN
* PWM1.2 DIO11 SERVO0_PIN
* PWM1.2 DIO54 X_STEP_PIN
* PWM1.3 DIO6 SERVO1_PIN J5-1
* PWM1.3 DIO60 Y_STEP_PIN
* PWM1.4 DIO53 SDSS(SSEL0) J3-5 AUX-3
* PWM1.4 DIO46 Z_STEP_PIN
* PWM1.5 DIO3 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.5 DIO9 RAMPS_D9_PIN
* PWM1.6 DIO14 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.6 DIO10 RAMPS_D10_PIN
*/
/**
* The following pins are NOT available in a Re-ARM system
* 7
* 17
* 22
* 23
* 25
* 27
* 29
* 32
* 39
* 40
* 42
* 43
* 44
* 45
* 47
* 64
* 65
* 66
*/
/**
* special pins
* D37 - not 5V tolerant
* D49 - not 5V tolerant
* D57 - open collector
* D58 - open collector
*
*/
Reference in New Issue View Git Blame Copy Permalink