3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-11-26 13:25:54 +00:00
Code Issues Releases Wiki Activity
31c473eadb
MarlinFirmware/Marlin/planner.cpp
Scott Lahteine 0ad8646a6c Fix block->mix_steps 
Fix #11484
2018-09-29 19:16:17 -05:00

2779 lines
109 KiB
C++
Raw Blame History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* planner.cpp
*
* Buffer movement commands and manage the acceleration profile plan
*
* Derived from Grbl
* Copyright (c) 2009-2011 Simen Svale Skogsrud
*
* The ring buffer implementation gleaned from the wiring_serial library by David A. Mellis.
*
*
* Reasoning behind the mathematics in this module (in the key of 'Mathematica'):
*
* s == speed, a == acceleration, t == time, d == distance
*
* Basic definitions:
* Speed[s_, a_, t_] := s + (a*t)
* Travel[s_, a_, t_] := Integrate[Speed[s, a, t], t]
*
* Distance to reach a specific speed with a constant acceleration:
* Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, d, t]
* d -> (m^2 - s^2)/(2 a) --> estimate_acceleration_distance()
*
* Speed after a given distance of travel with constant acceleration:
* Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, m, t]
* m -> Sqrt[2 a d + s^2]
*
* DestinationSpeed[s_, a_, d_] := Sqrt[2 a d + s^2]
*
* When to start braking (di) to reach a specified destination speed (s2) after accelerating
* from initial speed s1 without ever stopping at a plateau:
* Solve[{DestinationSpeed[s1, a, di] == DestinationSpeed[s2, a, d - di]}, di]
* di -> (2 a d - s1^2 + s2^2)/(4 a) --> intersection_distance()
*
* IntersectionDistance[s1_, s2_, a_, d_] := (2 a d - s1^2 + s2^2)/(4 a)
*
* --
*
* The fast inverse function needed for Bézier interpolation for AVR
* was designed, written and tested by Eduardo José Tagle on April/2018
*/
#include "planner.h"
#include "stepper.h"
#include "temperature.h"
#include "ultralcd.h"
#include "language.h"
#include "parser.h"
#include "Marlin.h"
#if ENABLED(MESH_BED_LEVELING)
#include "mesh_bed_leveling.h"
#elif ENABLED(AUTO_BED_LEVELING_UBL)
#include "ubl.h"
#endif
#if ENABLED(AUTO_POWER_CONTROL)
#include "power.h"
#endif
// Delay for delivery of first block to the stepper ISR, if the queue contains 2 or
// fewer movements. The delay is measured in milliseconds, and must be less than 250ms
#define BLOCK_DELAY_FOR_1ST_MOVE 100
Planner planner;
// public:
/**
* A ring buffer of moves described in steps
*/
block_t Planner::block_buffer[BLOCK_BUFFER_SIZE];
volatile uint8_t Planner::block_buffer_head, // Index of the next block to be pushed
Planner::block_buffer_nonbusy, // Index of the first non-busy block
Planner::block_buffer_planned, // Index of the optimally planned block
Planner::block_buffer_tail; // Index of the busy block, if any
uint16_t Planner::cleaning_buffer_counter; // A counter to disable queuing of blocks
uint8_t Planner::delay_before_delivering; // This counter delays delivery of blocks when queue becomes empty to allow the opportunity of merging blocks
uint32_t Planner::max_acceleration_mm_per_s2[NUM_AXIS_N], // (mm/s^2) M201 XYZE
Planner::max_acceleration_steps_per_s2[NUM_AXIS_N], // (steps/s^2) Derived from mm_per_s2
Planner::min_segment_time_us; // (µs) M205 Q
float Planner::max_feedrate_mm_s[NUM_AXIS_N], // (mm/s) M203 XYZE - Max speeds
Planner::axis_steps_per_mm[NUM_AXIS_N], // (steps) M92 XYZE - Steps per millimeter
Planner::steps_to_mm[NUM_AXIS_N], // (mm) Millimeters per step
Planner::min_feedrate_mm_s, // (mm/s) M205 S - Minimum linear feedrate
Planner::acceleration, // (mm/s^2) M204 S - Normal acceleration. DEFAULT ACCELERATION for all printing moves.
Planner::retract_acceleration, // (mm/s^2) M204 R - Retract acceleration. Filament pull-back and push-forward while standing still in the other axes
Planner::travel_acceleration, // (mm/s^2) M204 T - Travel acceleration. DEFAULT ACCELERATION for all NON printing moves.
Planner::min_travel_feedrate_mm_s; // (mm/s) M205 T - Minimum travel feedrate
#if ENABLED(JUNCTION_DEVIATION)
float Planner::junction_deviation_mm; // (mm) M205 J
#if ENABLED(LIN_ADVANCE)
#if ENABLED(DISTINCT_E_FACTORS)
float Planner::max_e_jerk[EXTRUDERS]; // Calculated from junction_deviation_mm
#else
float Planner::max_e_jerk;
#endif
#endif
#else
float Planner::max_jerk[NUM_AXIS]; // (mm/s^2) M205 XYZE - The largest speed change requiring no acceleration.
#endif
#if ENABLED(LINE_BUILDUP_COMPENSATION_FEATURE)
float Planner::k0[MOV_AXIS],
Planner::k1[MOV_AXIS],
Planner::k2[MOV_AXIS],
Planner::sqrtk1[MOV_AXIS];
#endif
#if ENABLED(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
bool Planner::abort_on_endstop_hit = false;
#endif
#if ENABLED(DISTINCT_E_FACTORS)
uint8_t Planner::last_extruder = 0; // Respond to extruder change
#define _EINDEX (E_AXIS + active_extruder)
#else
#define _EINDEX E_AXIS
#endif
int16_t Planner::flow_percentage[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(100); // Extrusion factor for each extruder
float Planner::e_factor[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(1.0f); // The flow percentage and volumetric multiplier combine to scale E movement
#if DISABLED(NO_VOLUMETRICS)
float Planner::filament_size[EXTRUDERS], // diameter of filament (in millimeters), typically around 1.75 or 2.85, 0 disables the volumetric calculations for the extruder
Planner::volumetric_area_nominal = CIRCLE_AREA(float(DEFAULT_NOMINAL_FILAMENT_DIA) * 0.5f), // Nominal cross-sectional area
Planner::volumetric_multiplier[EXTRUDERS]; // Reciprocal of cross-sectional area of filament (in mm^2). Pre-calculated to reduce computation in the planner
#endif
#if HAS_LEVELING
bool Planner::leveling_active = false; // Flag that auto bed leveling is enabled
#if ABL_PLANAR
matrix_3x3 Planner::bed_level_matrix; // Transform to compensate for bed level
#endif
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
float Planner::z_fade_height, // Initialized by settings.load()
Planner::inverse_z_fade_height,
Planner::last_fade_z;
#endif
#else
constexpr bool Planner::leveling_active;
#endif
#if ENABLED(SKEW_CORRECTION)
#if ENABLED(SKEW_CORRECTION_GCODE)
float Planner::xy_skew_factor;
#else
constexpr float Planner::xy_skew_factor;
#endif
#if ENABLED(SKEW_CORRECTION_FOR_Z) && ENABLED(SKEW_CORRECTION_GCODE)
float Planner::xz_skew_factor, Planner::yz_skew_factor;
#else
constexpr float Planner::xz_skew_factor, Planner::yz_skew_factor;
#endif
#endif
#if ENABLED(AUTOTEMP)
float Planner::autotemp_max = 250,
Planner::autotemp_min = 210,
Planner::autotemp_factor = 0.1f;
bool Planner::autotemp_enabled = false;
#endif
// private:
int32_t Planner::position[NUM_AXIS] = { 0 };
uint32_t Planner::cutoff_long;
float Planner::previous_speed[NUM_AXIS],
Planner::previous_nominal_speed_sqr;
#if ENABLED(DISABLE_INACTIVE_EXTRUDER)
uint8_t Planner::g_uc_extruder_last_move[EXTRUDERS] = { 0 };
#endif
#ifdef XY_FREQUENCY_LIMIT
// Old direction bits. Used for speed calculations
unsigned char Planner::old_direction_bits = 0;
// Segment times (in µs). Used for speed calculations
uint32_t Planner::axis_segment_time_us[2][3] = { { MAX_FREQ_TIME_US + 1, 0, 0 }, { MAX_FREQ_TIME_US + 1, 0, 0 } };
#endif
#if ENABLED(LIN_ADVANCE)
float Planner::extruder_advance_K; // Initialized by settings.load()
#endif
#if HAS_POSITION_FLOAT
float Planner::position_float[NUM_AXIS]; // Needed for accurate maths. Steps cannot be used!
#endif
#if ENABLED(ULTRA_LCD)
volatile uint32_t Planner::block_buffer_runtime_us = 0;
#endif
/**
* Class and Instance Methods
*/
Planner::Planner() { init(); }
void Planner::init() {
ZERO(position);
#if HAS_POSITION_FLOAT
ZERO(position_float);
#endif
ZERO(previous_speed);
previous_nominal_speed_sqr = 0;
#if ABL_PLANAR
bed_level_matrix.set_to_identity();
#endif
clear_block_buffer();
delay_before_delivering = 0;
}
#if ENABLED(S_CURVE_ACCELERATION)
/**
* This routine returns 0x1000000 / d, getting the inverse as fast as possible.
* A fast-converging iterative Newton-Raphson method can reach full precision in
* just 1 iteration, and takes 211 cycles (worst case; the mean case is less, up
* to 30 cycles for small divisors), instead of the 500 cycles a normal division
* would take.
*
* Inspired by the following page:
* https://stackoverflow.com/questions/27801397/newton-raphson-division-with-big-integers
*
* Suppose we want to calculate floor(2 ^ k / B) where B is a positive integer
* Then, B must be <= 2^k, otherwise, the quotient is 0.
*
* The Newton - Raphson iteration for x = B / 2 ^ k yields:
* q[n + 1] = q[n] * (2 - q[n] * B / 2 ^ k)
*
* This can be rearranged to:
* q[n + 1] = q[n] * (2 ^ (k + 1) - q[n] * B) >> k
*
* Each iteration requires only integer multiplications and bit shifts.
* It doesn't necessarily converge to floor(2 ^ k / B) but in the worst case
* it eventually alternates between floor(2 ^ k / B) and ceil(2 ^ k / B).
* So it checks for this case and extracts floor(2 ^ k / B).
*
* A simple but important optimization for this approach is to truncate
* multiplications (i.e., calculate only the higher bits of the product) in the
* early iterations of the Newton - Raphson method. This is done so the results
* of the early iterations are far from the quotient. Then it doesn't matter if
* they are done inaccurately.
* It's important to pick a good starting value for x. Knowing how many
* digits the divisor has, it can be estimated:
*
* 2^k / x = 2 ^ log2(2^k / x)
* 2^k / x = 2 ^(log2(2^k)-log2(x))
* 2^k / x = 2 ^(k*log2(2)-log2(x))
* 2^k / x = 2 ^ (k-log2(x))
* 2^k / x >= 2 ^ (k-floor(log2(x)))
* floor(log2(x)) is simply the index of the most significant bit set.
*
* If this estimation can be improved even further the number of iterations can be
* reduced a lot, saving valuable execution time.
* The paper "Software Integer Division" by Thomas L.Rodeheffer, Microsoft
* Research, Silicon Valley,August 26, 2008, available at
* https://www.microsoft.com/en-us/research/wp-content/uploads/2008/08/tr-2008-141.pdf
* suggests, for its integer division algorithm, using a table to supply the first
* 8 bits of precision, then, due to the quadratic convergence nature of the
* Newton-Raphon iteration, just 2 iterations should be enough to get maximum
* precision of the division.
* By precomputing values of inverses for small denominator values, just one
* Newton-Raphson iteration is enough to reach full precision.
* This code uses the top 9 bits of the denominator as index.
*
* The AVR assembly function implements this C code using the data below:
*
* // For small divisors, it is best to directly retrieve the results
* if (d <= 110) return pgm_read_dword(&small_inv_tab[d]);
*
* // Compute initial estimation of 0x1000000/x -
* // Get most significant bit set on divider
* uint8_t idx = 0;
* uint32_t nr = d;
* if (!(nr & 0xFF0000)) {
* nr <<= 8; idx += 8;
* if (!(nr & 0xFF0000)) { nr <<= 8; idx += 8; }
* }
* if (!(nr & 0xF00000)) { nr <<= 4; idx += 4; }
* if (!(nr & 0xC00000)) { nr <<= 2; idx += 2; }
* if (!(nr & 0x800000)) { nr <<= 1; idx += 1; }
*
* // Isolate top 9 bits of the denominator, to be used as index into the initial estimation table
* uint32_t tidx = nr >> 15, // top 9 bits. bit8 is always set
* ie = inv_tab[tidx & 0xFF] + 256, // Get the table value. bit9 is always set
* x = idx <= 8 ? (ie >> (8 - idx)) : (ie << (idx - 8)); // Position the estimation at the proper place
*
* x = uint32_t((x * uint64_t(_BV(25) - x * d)) >> 24); // Refine estimation by newton-raphson. 1 iteration is enough
* const uint32_t r = _BV(24) - x * d; // Estimate remainder
* if (r >= d) x++; // Check whether to adjust result
* return uint32_t(x); // x holds the proper estimation
*
*/
static uint32_t get_period_inverse(uint32_t d) {
static const uint8_t inv_tab[256] PROGMEM = {
255,253,252,250,248,246,244,242,240,238,236,234,233,231,229,227,
225,224,222,220,218,217,215,213,212,210,208,207,205,203,202,200,
199,197,195,194,192,191,189,188,186,185,183,182,180,179,178,176,
175,173,172,170,169,168,166,165,164,162,161,160,158,157,156,154,
153,152,151,149,148,147,146,144,143,142,141,139,138,137,136,135,
134,132,131,130,129,128,127,126,125,123,122,121,120,119,118,117,
116,115,114,113,112,111,110,109,108,107,106,105,104,103,102,101,
100,99,98,97,96,95,94,93,92,91,90,89,88,88,87,86,
85,84,83,82,81,80,80,79,78,77,76,75,74,74,73,72,
71,70,70,69,68,67,66,66,65,64,63,62,62,61,60,59,
59,58,57,56,56,55,54,53,53,52,51,50,50,49,48,48,
47,46,46,45,44,43,43,42,41,41,40,39,39,38,37,37,
36,35,35,34,33,33,32,32,31,30,30,29,28,28,27,27,
26,25,25,24,24,23,22,22,21,21,20,19,19,18,18,17,
17,16,15,15,14,14,13,13,12,12,11,10,10,9,9,8,
8,7,7,6,6,5,5,4,4,3,3,2,2,1,0,0
};
// For small denominators, it is cheaper to directly store the result.
// For bigger ones, just ONE Newton-Raphson iteration is enough to get
// maximum precision we need
static const uint32_t small_inv_tab[111] PROGMEM = {
16777216,16777216,8388608,5592405,4194304,3355443,2796202,2396745,2097152,1864135,1677721,1525201,1398101,1290555,1198372,1118481,
1048576,986895,932067,883011,838860,798915,762600,729444,699050,671088,645277,621378,599186,578524,559240,541200,
524288,508400,493447,479349,466033,453438,441505,430185,419430,409200,399457,390167,381300,372827,364722,356962,
349525,342392,335544,328965,322638,316551,310689,305040,299593,294337,289262,284359,279620,275036,270600,266305,
262144,258111,254200,250406,246723,243148,239674,236298,233016,229824,226719,223696,220752,217885,215092,212369,
209715,207126,204600,202135,199728,197379,195083,192841,190650,188508,186413,184365,182361,180400,178481,176602,
174762,172960,171196,169466,167772,166111,164482,162885,161319,159783,158275,156796,155344,153919,152520
};
// For small divisors, it is best to directly retrieve the results
if (d <= 110) return pgm_read_dword(&small_inv_tab[d]);
register uint8_t r8 = d & 0xFF,
r9 = (d >> 8) & 0xFF,
r10 = (d >> 16) & 0xFF,
r2,r3,r4,r5,r6,r7,r11,r12,r13,r14,r15,r16,r17,r18;
register const uint8_t* ptab = inv_tab;
__asm__ __volatile__(
// %8:%7:%6 = interval
// r31:r30: MUST be those registers, and they must point to the inv_tab
A("clr %13") // %13 = 0
// Now we must compute
// result = 0xFFFFFF / d
// %8:%7:%6 = interval
// %16:%15:%14 = nr
// %13 = 0
// A plain division of 24x24 bits should take 388 cycles to complete. We will
// use Newton-Raphson for the calculation, and will strive to get way less cycles
// for the same result - Using C division, it takes 500cycles to complete .
A("clr %3") // idx = 0
A("mov %14,%6")
A("mov %15,%7")
A("mov %16,%8") // nr = interval
A("tst %16") // nr & 0xFF0000 == 0 ?
A("brne 2f") // No, skip this
A("mov %16,%15")
A("mov %15,%14") // nr <<= 8, %14 not needed
A("subi %3,-8") // idx += 8
A("tst %16") // nr & 0xFF0000 == 0 ?
A("brne 2f") // No, skip this
A("mov %16,%15") // nr <<= 8, %14 not needed
A("clr %15") // We clear %14
A("subi %3,-8") // idx += 8
// here %16 != 0 and %16:%15 contains at least 9 MSBits, or both %16:%15 are 0
L("2")
A("cpi %16,0x10") // (nr & 0xF00000) == 0 ?
A("brcc 3f") // No, skip this
A("swap %15") // Swap nibbles
A("swap %16") // Swap nibbles. Low nibble is 0
A("mov %14, %15")
A("andi %14,0x0F") // Isolate low nibble
A("andi %15,0xF0") // Keep proper nibble in %15
A("or %16, %14") // %16:%15 <<= 4
A("subi %3,-4") // idx += 4
L("3")
A("cpi %16,0x40") // (nr & 0xC00000) == 0 ?
A("brcc 4f") // No, skip this
A("add %15,%15")
A("adc %16,%16")
A("add %15,%15")
A("adc %16,%16") // %16:%15 <<= 2
A("subi %3,-2") // idx += 2
L("4")
A("cpi %16,0x80") // (nr & 0x800000) == 0 ?
A("brcc 5f") // No, skip this
A("add %15,%15")
A("adc %16,%16") // %16:%15 <<= 1
A("inc %3") // idx += 1
// Now %16:%15 contains its MSBit set to 1, or %16:%15 is == 0. We are now absolutely sure
// we have at least 9 MSBits available to enter the initial estimation table
L("5")
A("add %15,%15")
A("adc %16,%16") // %16:%15 = tidx = (nr <<= 1), we lose the top MSBit (always set to 1, %16 is the index into the inverse table)
A("add r30,%16") // Only use top 8 bits
A("adc r31,%13") // r31:r30 = inv_tab + (tidx)
A("lpm %14, Z") // %14 = inv_tab[tidx]
A("ldi %15, 1") // %15 = 1 %15:%14 = inv_tab[tidx] + 256
// We must scale the approximation to the proper place
A("clr %16") // %16 will always be 0 here
A("subi %3,8") // idx == 8 ?
A("breq 6f") // yes, no need to scale
A("brcs 7f") // If C=1, means idx < 8, result was negative!
// idx > 8, now %3 = idx - 8. We must perform a left shift. idx range:[1-8]
A("sbrs %3,0") // shift by 1bit position?
A("rjmp 8f") // No
A("add %14,%14")
A("adc %15,%15") // %15:16 <<= 1
L("8")
A("sbrs %3,1") // shift by 2bit position?
A("rjmp 9f") // No
A("add %14,%14")
A("adc %15,%15")
A("add %14,%14")
A("adc %15,%15") // %15:16 <<= 1
L("9")
A("sbrs %3,2") // shift by 4bits position?
A("rjmp 16f") // No
A("swap %15") // Swap nibbles. lo nibble of %15 will always be 0
A("swap %14") // Swap nibbles
A("mov %12,%14")
A("andi %12,0x0F") // isolate low nibble
A("andi %14,0xF0") // and clear it
A("or %15,%12") // %15:%16 <<= 4
L("16")
A("sbrs %3,3") // shift by 8bits position?
A("rjmp 6f") // No, we are done
A("mov %16,%15")
A("mov %15,%14")
A("clr %14")
A("jmp 6f")
// idx < 8, now %3 = idx - 8. Get the count of bits
L("7")
A("neg %3") // %3 = -idx = count of bits to move right. idx range:[1...8]
A("sbrs %3,0") // shift by 1 bit position ?
A("rjmp 10f") // No, skip it
A("asr %15") // (bit7 is always 0 here)
A("ror %14")
L("10")
A("sbrs %3,1") // shift by 2 bit position ?
A("rjmp 11f") // No, skip it
A("asr %15") // (bit7 is always 0 here)
A("ror %14")
A("asr %15") // (bit7 is always 0 here)
A("ror %14")
L("11")
A("sbrs %3,2") // shift by 4 bit position ?
A("rjmp 12f") // No, skip it
A("swap %15") // Swap nibbles
A("andi %14, 0xF0") // Lose the lowest nibble
A("swap %14") // Swap nibbles. Upper nibble is 0
A("or %14,%15") // Pass nibble from upper byte
A("andi %15, 0x0F") // And get rid of that nibble
L("12")
A("sbrs %3,3") // shift by 8 bit position ?
A("rjmp 6f") // No, skip it
A("mov %14,%15")
A("clr %15")
L("6") // %16:%15:%14 = initial estimation of 0x1000000 / d
// Now, we must refine the estimation present on %16:%15:%14 using 1 iteration
// of Newton-Raphson. As it has a quadratic convergence, 1 iteration is enough
// to get more than 18bits of precision (the initial table lookup gives 9 bits of
// precision to start from). 18bits of precision is all what is needed here for result
// %8:%7:%6 = d = interval
// %16:%15:%14 = x = initial estimation of 0x1000000 / d
// %13 = 0
// %3:%2:%1:%0 = working accumulator
// Compute 1<<25 - x*d. Result should never exceed 25 bits and should always be positive
A("clr %0")
A("clr %1")
A("clr %2")
A("ldi %3,2") // %3:%2:%1:%0 = 0x2000000
A("mul %6,%14") // r1:r0 = LO(d) * LO(x)
A("sub %0,r0")
A("sbc %1,r1")
A("sbc %2,%13")
A("sbc %3,%13") // %3:%2:%1:%0 -= LO(d) * LO(x)
A("mul %7,%14") // r1:r0 = MI(d) * LO(x)
A("sub %1,r0")
A("sbc %2,r1")
A("sbc %3,%13") // %3:%2:%1:%0 -= MI(d) * LO(x) << 8
A("mul %8,%14") // r1:r0 = HI(d) * LO(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= MIL(d) * LO(x) << 16
A("mul %6,%15") // r1:r0 = LO(d) * MI(x)
A("sub %1,r0")
A("sbc %2,r1")
A("sbc %3,%13") // %3:%2:%1:%0 -= LO(d) * MI(x) << 8
A("mul %7,%15") // r1:r0 = MI(d) * MI(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= MI(d) * MI(x) << 16
A("mul %8,%15") // r1:r0 = HI(d) * MI(x)
A("sub %3,r0") // %3:%2:%1:%0 -= MIL(d) * MI(x) << 24
A("mul %6,%16") // r1:r0 = LO(d) * HI(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= LO(d) * HI(x) << 16
A("mul %7,%16") // r1:r0 = MI(d) * HI(x)
A("sub %3,r0") // %3:%2:%1:%0 -= MI(d) * HI(x) << 24
// %3:%2:%1:%0 = (1<<25) - x*d [169]
// We need to multiply that result by x, and we are only interested in the top 24bits of that multiply
// %16:%15:%14 = x = initial estimation of 0x1000000 / d
// %3:%2:%1:%0 = (1<<25) - x*d = acc
// %13 = 0
// result = %11:%10:%9:%5:%4
A("mul %14,%0") // r1:r0 = LO(x) * LO(acc)
A("mov %4,r1")
A("clr %5")
A("clr %9")
A("clr %10")
A("clr %11") // %11:%10:%9:%5:%4 = LO(x) * LO(acc) >> 8
A("mul %15,%0") // r1:r0 = MI(x) * LO(acc)
A("add %4,r0")
A("adc %5,r1")
A("adc %9,%13")
A("adc %10,%13")
A("adc %11,%13") // %11:%10:%9:%5:%4 += MI(x) * LO(acc)
A("mul %16,%0") // r1:r0 = HI(x) * LO(acc)
A("add %5,r0")
A("adc %9,r1")
A("adc %10,%13")
A("adc %11,%13") // %11:%10:%9:%5:%4 += MI(x) * LO(acc) << 8
A("mul %14,%1") // r1:r0 = LO(x) * MIL(acc)
A("add %4,r0")
A("adc %5,r1")
A("adc %9,%13")
A("adc %10,%13")
A("adc %11,%13") // %11:%10:%9:%5:%4 = LO(x) * MIL(acc)
A("mul %15,%1") // r1:r0 = MI(x) * MIL(acc)
A("add %5,r0")
A("adc %9,r1")
A("adc %10,%13")
A("adc %11,%13") // %11:%10:%9:%5:%4 += MI(x) * MIL(acc) << 8
A("mul %16,%1") // r1:r0 = HI(x) * MIL(acc)
A("add %9,r0")
A("adc %10,r1")
A("adc %11,%13") // %11:%10:%9:%5:%4 += MI(x) * MIL(acc) << 16
A("mul %14,%2") // r1:r0 = LO(x) * MIH(acc)
A("add %5,r0")
A("adc %9,r1")
A("adc %10,%13")
A("adc %11,%13") // %11:%10:%9:%5:%4 = LO(x) * MIH(acc) << 8
A("mul %15,%2") // r1:r0 = MI(x) * MIH(acc)
A("add %9,r0")
A("adc %10,r1")
A("adc %11,%13") // %11:%10:%9:%5:%4 += MI(x) * MIH(acc) << 16
A("mul %16,%2") // r1:r0 = HI(x) * MIH(acc)
A("add %10,r0")
A("adc %11,r1") // %11:%10:%9:%5:%4 += MI(x) * MIH(acc) << 24
A("mul %14,%3") // r1:r0 = LO(x) * HI(acc)
A("add %9,r0")
A("adc %10,r1")
A("adc %11,%13") // %11:%10:%9:%5:%4 = LO(x) * HI(acc) << 16
A("mul %15,%3") // r1:r0 = MI(x) * HI(acc)
A("add %10,r0")
A("adc %11,r1") // %11:%10:%9:%5:%4 += MI(x) * HI(acc) << 24
A("mul %16,%3") // r1:r0 = HI(x) * HI(acc)
A("add %11,r0") // %11:%10:%9:%5:%4 += MI(x) * HI(acc) << 32
// At this point, %11:%10:%9 contains the new estimation of x.
// Finally, we must correct the result. Estimate remainder as
// (1<<24) - x*d
// %11:%10:%9 = x
// %8:%7:%6 = d = interval" "\n\t"
A("ldi %3,1")
A("clr %2")
A("clr %1")
A("clr %0") // %3:%2:%1:%0 = 0x1000000
A("mul %6,%9") // r1:r0 = LO(d) * LO(x)
A("sub %0,r0")
A("sbc %1,r1")
A("sbc %2,%13")
A("sbc %3,%13") // %3:%2:%1:%0 -= LO(d) * LO(x)
A("mul %7,%9") // r1:r0 = MI(d) * LO(x)
A("sub %1,r0")
A("sbc %2,r1")
A("sbc %3,%13") // %3:%2:%1:%0 -= MI(d) * LO(x) << 8
A("mul %8,%9") // r1:r0 = HI(d) * LO(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= MIL(d) * LO(x) << 16
A("mul %6,%10") // r1:r0 = LO(d) * MI(x)
A("sub %1,r0")
A("sbc %2,r1")
A("sbc %3,%13") // %3:%2:%1:%0 -= LO(d) * MI(x) << 8
A("mul %7,%10") // r1:r0 = MI(d) * MI(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= MI(d) * MI(x) << 16
A("mul %8,%10") // r1:r0 = HI(d) * MI(x)
A("sub %3,r0") // %3:%2:%1:%0 -= MIL(d) * MI(x) << 24
A("mul %6,%11") // r1:r0 = LO(d) * HI(x)
A("sub %2,r0")
A("sbc %3,r1") // %3:%2:%1:%0 -= LO(d) * HI(x) << 16
A("mul %7,%11") // r1:r0 = MI(d) * HI(x)
A("sub %3,r0") // %3:%2:%1:%0 -= MI(d) * HI(x) << 24
// %3:%2:%1:%0 = r = (1<<24) - x*d
// %8:%7:%6 = d = interval
// Perform the final correction
A("sub %0,%6")
A("sbc %1,%7")
A("sbc %2,%8") // r -= d
A("brcs 14f") // if ( r >= d)
// %11:%10:%9 = x
A("ldi %3,1")
A("add %9,%3")
A("adc %10,%13")
A("adc %11,%13") // x++
L("14")
// Estimation is done. %11:%10:%9 = x
A("clr __zero_reg__") // Make C runtime happy
// [211 cycles total]
: "=r" (r2),
"=r" (r3),
"=r" (r4),
"=d" (r5),
"=r" (r6),
"=r" (r7),
"+r" (r8),
"+r" (r9),
"+r" (r10),
"=d" (r11),
"=r" (r12),
"=r" (r13),
"=d" (r14),
"=d" (r15),
"=d" (r16),
"=d" (r17),
"=d" (r18),
"+z" (ptab)
:
: "r0", "r1", "cc"
);
// Return the result
return r11 | (uint16_t(r12) << 8) | (uint32_t(r13) << 16);
}
#endif // S_CURVE_ACCELERATION
#define MINIMAL_STEP_RATE 120
/**
* Calculate trapezoid parameters, multiplying the entry- and exit-speeds
* by the provided factors.
**
* ############ VERY IMPORTANT ############
* NOTE that the PRECONDITION to call this function is that the block is
* NOT BUSY and it is marked as RECALCULATE. That WARRANTIES the Stepper ISR
* is not and will not use the block while we modify it, so it is safe to
* alter its values.
*/
void Planner::calculate_trapezoid_for_block(block_t* const block, const float &entry_factor, const float &exit_factor) {
uint32_t initial_rate = CEIL(block->nominal_rate * entry_factor),
final_rate = CEIL(block->nominal_rate * exit_factor); // (steps per second)
// Limit minimal step rate (Otherwise the timer will overflow.)
NOLESS(initial_rate, uint32_t(MINIMAL_STEP_RATE));
NOLESS(final_rate, uint32_t(MINIMAL_STEP_RATE));
#if ENABLED(S_CURVE_ACCELERATION)
uint32_t cruise_rate = initial_rate;
#endif
const int32_t accel = block->acceleration_steps_per_s2;
// Steps required for acceleration, deceleration to/from nominal rate
uint32_t accelerate_steps = CEIL(estimate_acceleration_distance(initial_rate, block->nominal_rate, accel)),
decelerate_steps = FLOOR(estimate_acceleration_distance(block->nominal_rate, final_rate, -accel));
// Steps between acceleration and deceleration, if any
int32_t plateau_steps = block->step_event_count - accelerate_steps - decelerate_steps;
// Does accelerate_steps + decelerate_steps exceed step_event_count?
// Then we can't possibly reach the nominal rate, there will be no cruising.
// Use intersection_distance() to calculate accel / braking time in order to
// reach the final_rate exactly at the end of this block.
if (plateau_steps < 0) {
const float accelerate_steps_float = CEIL(intersection_distance(initial_rate, final_rate, accel, block->step_event_count));
accelerate_steps = MIN(uint32_t(MAX(accelerate_steps_float, 0)), block->step_event_count);
plateau_steps = 0;
#if ENABLED(S_CURVE_ACCELERATION)
// We won't reach the cruising rate. Let's calculate the speed we will reach
cruise_rate = final_speed(initial_rate, accel, accelerate_steps);
#endif
}
#if ENABLED(S_CURVE_ACCELERATION)
else // We have some plateau time, so the cruise rate will be the nominal rate
cruise_rate = block->nominal_rate;
#endif
#if ENABLED(S_CURVE_ACCELERATION)
// Jerk controlled speed requires to express speed versus time, NOT steps
uint32_t acceleration_time = ((float)(cruise_rate - initial_rate) / accel) * (STEPPER_TIMER_RATE),
deceleration_time = ((float)(cruise_rate - final_rate) / accel) * (STEPPER_TIMER_RATE);
// And to offload calculations from the ISR, we also calculate the inverse of those times here
uint32_t acceleration_time_inverse = get_period_inverse(acceleration_time);
uint32_t deceleration_time_inverse = get_period_inverse(deceleration_time);
#endif
// Store new block parameters
block->accelerate_until = accelerate_steps;
block->decelerate_after = accelerate_steps + plateau_steps;
block->initial_rate = initial_rate;
#if ENABLED(S_CURVE_ACCELERATION)
block->acceleration_time = acceleration_time;
block->deceleration_time = deceleration_time;
block->acceleration_time_inverse = acceleration_time_inverse;
block->deceleration_time_inverse = deceleration_time_inverse;
block->cruise_rate = cruise_rate;
#endif
block->final_rate = final_rate;
}
/* PLANNER SPEED DEFINITION
+--------+ <- current->nominal_speed
/ \
current->entry_speed -> + \
| + <- next->entry_speed (aka exit speed)
+-------------+
time -->
Recalculates the motion plan according to the following basic guidelines:
1. Go over every feasible block sequentially in reverse order and calculate the junction speeds
(i.e. current->entry_speed) such that:
a. No junction speed exceeds the pre-computed maximum junction speed limit or nominal speeds of
neighboring blocks.
b. A block entry speed cannot exceed one reverse-computed from its exit speed (next->entry_speed)
with a maximum allowable deceleration over the block travel distance.
c. The last (or newest appended) block is planned from a complete stop (an exit speed of zero).
2. Go over every block in chronological (forward) order and dial down junction speed values if
a. The exit speed exceeds the one forward-computed from its entry speed with the maximum allowable
acceleration over the block travel distance.
When these stages are complete, the planner will have maximized the velocity profiles throughout the all
of the planner blocks, where every block is operating at its maximum allowable acceleration limits. In
other words, for all of the blocks in the planner, the plan is optimal and no further speed improvements
are possible. If a new block is added to the buffer, the plan is recomputed according to the said
guidelines for a new optimal plan.
To increase computational efficiency of these guidelines, a set of planner block pointers have been
created to indicate stop-compute points for when the planner guidelines cannot logically make any further
changes or improvements to the plan when in normal operation and new blocks are streamed and added to the
planner buffer. For example, if a subset of sequential blocks in the planner have been planned and are
bracketed by junction velocities at their maximums (or by the first planner block as well), no new block
added to the planner buffer will alter the velocity profiles within them. So we no longer have to compute
them. Or, if a set of sequential blocks from the first block in the planner (or a optimal stop-compute
point) are all accelerating, they are all optimal and can not be altered by a new block added to the
planner buffer, as this will only further increase the plan speed to chronological blocks until a maximum
junction velocity is reached. However, if the operational conditions of the plan changes from infrequently
used feed holds or feedrate overrides, the stop-compute pointers will be reset and the entire plan is
recomputed as stated in the general guidelines.
Planner buffer index mapping:
- block_buffer_tail: Points to the beginning of the planner buffer. First to be executed or being executed.
- block_buffer_head: Points to the buffer block after the last block in the buffer. Used to indicate whether
the buffer is full or empty. As described for standard ring buffers, this block is always empty.
- block_buffer_planned: Points to the first buffer block after the last optimally planned block for normal
streaming operating conditions. Use for planning optimizations by avoiding recomputing parts of the
planner buffer that don't change with the addition of a new block, as describe above. In addition,
this block can never be less than block_buffer_tail and will always be pushed forward and maintain
this requirement when encountered by the Planner::discard_current_block() routine during a cycle.
NOTE: Since the planner only computes on what's in the planner buffer, some motions with lots of short
line segments, like G2/3 arcs or complex curves, may seem to move slow. This is because there simply isn't
enough combined distance traveled in the entire buffer to accelerate up to the nominal speed and then
decelerate to a complete stop at the end of the buffer, as stated by the guidelines. If this happens and
becomes an annoyance, there are a few simple solutions: (1) Maximize the machine acceleration. The planner
will be able to compute higher velocity profiles within the same combined distance. (2) Maximize line
motion(s) distance per block to a desired tolerance. The more combined distance the planner has to use,
the faster it can go. (3) Maximize the planner buffer size. This also will increase the combined distance
for the planner to compute over. It also increases the number of computations the planner has to perform
to compute an optimal plan, so select carefully.
*/
// The kernel called by recalculate() when scanning the plan from last to first entry.
void Planner::reverse_pass_kernel(block_t* const current, const block_t * const next) {
if (current) {
// If entry speed is already at the maximum entry speed, and there was no change of speed
// in the next block, there is no need to recheck. Block is cruising and there is no need to
// compute anything for this block,
// If not, block entry speed needs to be recalculated to ensure maximum possible planned speed.
const float max_entry_speed_sqr = current->max_entry_speed_sqr;
// Compute maximum entry speed decelerating over the current block from its exit speed.
// If not at the maximum entry speed, or the previous block entry speed changed
if (current->entry_speed_sqr != max_entry_speed_sqr || (next && TEST(next->flag, BLOCK_BIT_RECALCULATE))) {
// If nominal length true, max junction speed is guaranteed to be reached.
// If a block can de/ac-celerate from nominal speed to zero within the length of the block, then
// the current block and next block junction speeds are guaranteed to always be at their maximum
// junction speeds in deceleration and acceleration, respectively. This is due to how the current
// block nominal speed limits both the current and next maximum junction speeds. Hence, in both
// the reverse and forward planners, the corresponding block junction speed will always be at the
// the maximum junction speed and may always be ignored for any speed reduction checks.
const float new_entry_speed_sqr = TEST(current->flag, BLOCK_BIT_NOMINAL_LENGTH)
? max_entry_speed_sqr
: MIN(max_entry_speed_sqr, max_allowable_speed_sqr(-current->acceleration, next ? next->entry_speed_sqr : sq(float(MINIMUM_PLANNER_SPEED)), current->millimeters));
if (current->entry_speed_sqr != new_entry_speed_sqr) {
// Need to recalculate the block speed - Mark it now, so the stepper
// ISR does not consume the block before being recalculated
SBI(current->flag, BLOCK_BIT_RECALCULATE);
// But there is an inherent race condition here, as the block may have
// become BUSY just before being marked RECALCULATE, so check for that!
if (stepper.is_block_busy(current)) {
// Block became busy. Clear the RECALCULATE flag (no point in
// recalculating BUSY blocks). And don't set its speed, as it can't
// be updated at this time.
CBI(current->flag, BLOCK_BIT_RECALCULATE);
}
else {
// Block is not BUSY so this is ahead of the Stepper ISR:
// Just Set the new entry speed.
current->entry_speed_sqr = new_entry_speed_sqr;
}
}
}
}
}
/**
* recalculate() needs to go over the current plan twice.
* Once in reverse and once forward. This implements the reverse pass.
*/
void Planner::reverse_pass() {
// Initialize block index to the last block in the planner buffer.
uint8_t block_index = prev_block_index(block_buffer_head);
// Read the index of the last buffer planned block.
// The ISR may change it so get a stable local copy.
uint8_t planned_block_index = block_buffer_planned;
// If there was a race condition and block_buffer_planned was incremented
// or was pointing at the head (queue empty) break loop now and avoid
// planning already consumed blocks
if (planned_block_index == block_buffer_head) return;
// Reverse Pass: Coarsely maximize all possible deceleration curves back-planning from the last
// block in buffer. Cease planning when the last optimal planned or tail pointer is reached.
// NOTE: Forward pass will later refine and correct the reverse pass to create an optimal plan.
const block_t *next = NULL;
while (block_index != planned_block_index) {
// Perform the reverse pass
block_t *current = &block_buffer[block_index];
// Only consider non sync blocks
if (!TEST(current->flag, BLOCK_BIT_SYNC_POSITION)) {
reverse_pass_kernel(current, next);
next = current;
}
// Advance to the next
block_index = prev_block_index(block_index);
// The ISR could advance the block_buffer_planned while we were doing the reverse pass.
// We must try to avoid using an already consumed block as the last one - So follow
// changes to the pointer and make sure to limit the loop to the currently busy block
while (planned_block_index != block_buffer_planned) {
// If we reached the busy block or an already processed block, break the loop now
if (block_index == planned_block_index) return;
// Advance the pointer, following the busy block
planned_block_index = next_block_index(planned_block_index);
}
}
}
// The kernel called by recalculate() when scanning the plan from first to last entry.
void Planner::forward_pass_kernel(const block_t* const previous, block_t* const current, const uint8_t block_index) {
if (previous) {
// If the previous block is an acceleration block, too short to complete the full speed
// change, adjust the entry speed accordingly. Entry speeds have already been reset,
// maximized, and reverse-planned. If nominal length is set, max junction speed is
// guaranteed to be reached. No need to recheck.
if (!TEST(previous->flag, BLOCK_BIT_NOMINAL_LENGTH) &&
previous->entry_speed_sqr < current->entry_speed_sqr) {
// Compute the maximum allowable speed
const float new_entry_speed_sqr = max_allowable_speed_sqr(-previous->acceleration, previous->entry_speed_sqr, previous->millimeters);
// If true, current block is full-acceleration and we can move the planned pointer forward.
if (new_entry_speed_sqr < current->entry_speed_sqr) {
// Mark we need to recompute the trapezoidal shape, and do it now,
// so the stepper ISR does not consume the block before being recalculated
SBI(current->flag, BLOCK_BIT_RECALCULATE);
// But there is an inherent race condition here, as the block maybe
// became BUSY, just before it was marked as RECALCULATE, so check
// if that is the case!
if (stepper.is_block_busy(current)) {
// Block became busy. Clear the RECALCULATE flag (no point in
// recalculating BUSY blocks and don't set its speed, as it can't
// be updated at this time.
CBI(current->flag, BLOCK_BIT_RECALCULATE);
}
else {
// Block is not BUSY, we won the race against the Stepper ISR:
// Always <= max_entry_speed_sqr. Backward pass sets this.
current->entry_speed_sqr = new_entry_speed_sqr; // Always <= max_entry_speed_sqr. Backward pass sets this.
// Set optimal plan pointer.
block_buffer_planned = block_index;
}
}
}
// Any block set at its maximum entry speed also creates an optimal plan up to this
// point in the buffer. When the plan is bracketed by either the beginning of the
// buffer and a maximum entry speed or two maximum entry speeds, every block in between
// cannot logically be further improved. Hence, we don't have to recompute them anymore.
if (current->entry_speed_sqr == current->max_entry_speed_sqr)
block_buffer_planned = block_index;
}
}
/**
* recalculate() needs to go over the current plan twice.
* Once in reverse and once forward. This implements the forward pass.
*/
void Planner::forward_pass() {
// Forward Pass: Forward plan the acceleration curve from the planned pointer onward.
// Also scans for optimal plan breakpoints and appropriately updates the planned pointer.
// Begin at buffer planned pointer. Note that block_buffer_planned can be modified
// by the stepper ISR, so read it ONCE. It it guaranteed that block_buffer_planned
// will never lead head, so the loop is safe to execute. Also note that the forward
// pass will never modify the values at the tail.
uint8_t block_index = block_buffer_planned;
block_t *current;
const block_t * previous = NULL;
while (block_index != block_buffer_head) {
// Perform the forward pass
current = &block_buffer[block_index];
// Skip SYNC blocks
if (!TEST(current->flag, BLOCK_BIT_SYNC_POSITION)) {
// If there's no previous block or the previous block is not
// BUSY (thus, modifiable) run the forward_pass_kernel. Otherwise,
// the previous block became BUSY, so assume the current block's
// entry speed can't be altered (since that would also require
// updating the exit speed of the previous block).
if (!previous || !stepper.is_block_busy(previous))
forward_pass_kernel(previous, current, block_index);
previous = current;
}
// Advance to the previous
block_index = next_block_index(block_index);
}
}
/**
* Recalculate the trapezoid speed profiles for all blocks in the plan
* according to the entry_factor for each junction. Must be called by
* recalculate() after updating the blocks.
*/
void Planner::recalculate_trapezoids() {
// The tail may be changed by the ISR so get a local copy.
uint8_t block_index = block_buffer_tail,
head_block_index = block_buffer_head;
// Since there could be a sync block in the head of the queue, and the
// next loop must not recalculate the head block (as it needs to be
// specially handled), scan backwards to the first non-SYNC block.
while (head_block_index != block_index) {
// Go back (head always point to the first free block)
const uint8_t prev_index = prev_block_index(head_block_index);
// Get the pointer to the block
block_t *prev = &block_buffer[prev_index];
// If not dealing with a sync block, we are done. The last block is not a SYNC block
if (!TEST(prev->flag, BLOCK_BIT_SYNC_POSITION)) break;
// Examine the previous block. This and all following are SYNC blocks
head_block_index = prev_index;
}
// Go from the tail (currently executed block) to the first block, without including it)
block_t *current = NULL, *next = NULL;
float current_entry_speed = 0.0, next_entry_speed = 0.0;
while (block_index != head_block_index) {
next = &block_buffer[block_index];
// Skip sync blocks
if (!TEST(next->flag, BLOCK_BIT_SYNC_POSITION)) {
next_entry_speed = SQRT(next->entry_speed_sqr);
if (current) {
// Recalculate if current block entry or exit junction speed has changed.
if (TEST(current->flag, BLOCK_BIT_RECALCULATE) || TEST(next->flag, BLOCK_BIT_RECALCULATE)) {
// Mark the current block as RECALCULATE, to protect it from the Stepper ISR running it.
// Note that due to the above condition, there's a chance the current block isn't marked as
// RECALCULATE yet, but the next one is. That's the reason for the following line.
SBI(current->flag, BLOCK_BIT_RECALCULATE);
// But there is an inherent race condition here, as the block maybe
// became BUSY, just before it was marked as RECALCULATE, so check
// if that is the case!
if (!stepper.is_block_busy(current)) {
// Block is not BUSY, we won the race against the Stepper ISR:
// NOTE: Entry and exit factors always > 0 by all previous logic operations.
const float current_nominal_speed = SQRT(current->nominal_speed_sqr),
nomr = 1.0f / current_nominal_speed;
calculate_trapezoid_for_block(current, current_entry_speed * nomr, next_entry_speed * nomr);
#if ENABLED(LIN_ADVANCE)
if (current->use_advance_lead) {
const float comp = current->e_D_ratio * extruder_advance_K * axis_steps_per_mm[E_AXIS];
current->max_adv_steps = current_nominal_speed * comp;
current->final_adv_steps = next_entry_speed * comp;
}
#endif
}
// Reset current only to ensure next trapezoid is computed - The
// stepper is free to use the block from now on.
CBI(current->flag, BLOCK_BIT_RECALCULATE);
}
}
current = next;
current_entry_speed = next_entry_speed;
}
block_index = next_block_index(block_index);
}
// Last/newest block in buffer. Exit speed is set with MINIMUM_PLANNER_SPEED. Always recalculated.
if (next) {
// Mark the next(last) block as RECALCULATE, to prevent the Stepper ISR running it.
// As the last block is always recalculated here, there is a chance the block isn't
// marked as RECALCULATE yet. That's the reason for the following line.
SBI(next->flag, BLOCK_BIT_RECALCULATE);
// But there is an inherent race condition here, as the block maybe
// became BUSY, just before it was marked as RECALCULATE, so check
// if that is the case!
if (!stepper.is_block_busy(current)) {
// Block is not BUSY, we won the race against the Stepper ISR:
const float next_nominal_speed = SQRT(next->nominal_speed_sqr),
nomr = 1.0f / next_nominal_speed;
calculate_trapezoid_for_block(next, next_entry_speed * nomr, float(MINIMUM_PLANNER_SPEED) * nomr);
#if ENABLED(LIN_ADVANCE)
if (next->use_advance_lead) {
const float comp = next->e_D_ratio * extruder_advance_K * axis_steps_per_mm[E_AXIS];
next->max_adv_steps = next_nominal_speed * comp;
next->final_adv_steps = (MINIMUM_PLANNER_SPEED) * comp;
}
#endif
}
// Reset next only to ensure its trapezoid is computed - The stepper is free to use
// the block from now on.
CBI(next->flag, BLOCK_BIT_RECALCULATE);
}
}
void Planner::recalculate() {
// Initialize block index to the last block in the planner buffer.
const uint8_t block_index = prev_block_index(block_buffer_head);
// If there is just one block, no planning can be done. Avoid it!
if (block_index != block_buffer_planned) {
reverse_pass();
forward_pass();
}
recalculate_trapezoids();
}
#if ENABLED(AUTOTEMP)
void Planner::getHighESpeed() {
static float oldt = 0;
if (!autotemp_enabled) return;
if (thermalManager.degTargetHotend(0) + 2 < autotemp_min) return; // probably temperature set to zero.
float high = 0.0;
for (uint8_t b = block_buffer_tail; b != block_buffer_head; b = next_block_index(b)) {
block_t* block = &block_buffer[b];
if (
#if ENABLED(HANGPRINTER)
block->steps[A_AXIS] || block->steps[B_AXIS] || block->steps[C_AXIS] || block->steps[D_AXIS]
#else
block->steps[X_AXIS] || block->steps[Y_AXIS] || block->steps[Z_AXIS]
#endif
) {
const float se = (float)block->steps[E_AXIS] / block->step_event_count * SQRT(block->nominal_speed_sqr); // mm/sec;
NOLESS(high, se);
}
}
float t = autotemp_min + high * autotemp_factor;
t = constrain(t, autotemp_min, autotemp_max);
if (t < oldt) t = t * (1 - float(AUTOTEMP_OLDWEIGHT)) + oldt * float(AUTOTEMP_OLDWEIGHT);
oldt = t;
thermalManager.setTargetHotend(t, 0);
}
#endif // AUTOTEMP
/**
* Maintain fans, paste extruder pressure,
*/
void Planner::check_axes_activity() {
unsigned char axis_active[NUM_AXIS] = { 0 },
tail_fan_speed[FAN_COUNT];
#if ENABLED(BARICUDA)
#if HAS_HEATER_1
uint8_t tail_valve_pressure;
#endif
#if HAS_HEATER_2
uint8_t tail_e_to_p_pressure;
#endif
#endif
if (has_blocks_queued()) {
#if FAN_COUNT > 0
for (uint8_t i = 0; i < FAN_COUNT; i++)
tail_fan_speed[i] = block_buffer[block_buffer_tail].fan_speed[i];
#endif
block_t* block;
#if ENABLED(BARICUDA)
block = &block_buffer[block_buffer_tail];
#if HAS_HEATER_1
tail_valve_pressure = block->valve_pressure;
#endif
#if HAS_HEATER_2
tail_e_to_p_pressure = block->e_to_p_pressure;
#endif
#endif
for (uint8_t b = block_buffer_tail; b != block_buffer_head; b = next_block_index(b)) {
block = &block_buffer[b];
LOOP_XYZE(i) if (block->steps[i]) axis_active[i]++;
}
}
else {
#if FAN_COUNT > 0
for (uint8_t i = 0; i < FAN_COUNT; i++) tail_fan_speed[i] = fanSpeeds[i];
#endif
#if ENABLED(BARICUDA)
#if HAS_HEATER_1
tail_valve_pressure = baricuda_valve_pressure;
#endif
#if HAS_HEATER_2
tail_e_to_p_pressure = baricuda_e_to_p_pressure;
#endif
#endif
}
#if ENABLED(DISABLE_X)
if (!axis_active[X_AXIS]) disable_X();
#endif
#if ENABLED(DISABLE_Y)
if (!axis_active[Y_AXIS]) disable_Y();
#endif
#if ENABLED(DISABLE_Z)
if (!axis_active[Z_AXIS]) disable_Z();
#endif
#if ENABLED(DISABLE_E)
if (!axis_active[E_AXIS]) disable_e_steppers();
#endif
#if FAN_COUNT > 0
#if FAN_KICKSTART_TIME > 0
static millis_t fan_kick_end[FAN_COUNT] = { 0 };
#define KICKSTART_FAN(f) \
if (tail_fan_speed[f]) { \
millis_t ms = millis(); \
if (fan_kick_end[f] == 0) { \
fan_kick_end[f] = ms + FAN_KICKSTART_TIME; \
tail_fan_speed[f] = 255; \
} else if (PENDING(ms, fan_kick_end[f])) \
tail_fan_speed[f] = 255; \
} else fan_kick_end[f] = 0
#if HAS_FAN0
KICKSTART_FAN(0);
#endif
#if HAS_FAN1
KICKSTART_FAN(1);
#endif
#if HAS_FAN2
KICKSTART_FAN(2);
#endif
#endif // FAN_KICKSTART_TIME > 0
#if FAN_MIN_PWM != 0 || FAN_MAX_PWM != 255
#define CALC_FAN_SPEED(f) (tail_fan_speed[f] ? map(tail_fan_speed[f], 1, 255, FAN_MIN_PWM, FAN_MAX_PWM) : 0)
#else
#define CALC_FAN_SPEED(f) tail_fan_speed[f]
#endif
#if ENABLED(FAN_SOFT_PWM)
#if HAS_FAN0
thermalManager.soft_pwm_amount_fan[0] = CALC_FAN_SPEED(0);
#endif
#if HAS_FAN1
thermalManager.soft_pwm_amount_fan[1] = CALC_FAN_SPEED(1);
#endif
#if HAS_FAN2
thermalManager.soft_pwm_amount_fan[2] = CALC_FAN_SPEED(2);
#endif
#else
#if HAS_FAN0
analogWrite(FAN_PIN, CALC_FAN_SPEED(0));
#endif
#if HAS_FAN1
analogWrite(FAN1_PIN, CALC_FAN_SPEED(1));
#endif
#if HAS_FAN2
analogWrite(FAN2_PIN, CALC_FAN_SPEED(2));
#endif
#endif
#endif // FAN_COUNT > 0
#if ENABLED(AUTOTEMP)
getHighESpeed();
#endif
#if ENABLED(BARICUDA)
#if HAS_HEATER_1
analogWrite(HEATER_1_PIN, tail_valve_pressure);
#endif
#if HAS_HEATER_2
analogWrite(HEATER_2_PIN, tail_e_to_p_pressure);
#endif
#endif
}
#if DISABLED(NO_VOLUMETRICS)
/**
* Get a volumetric multiplier from a filament diameter.
* This is the reciprocal of the circular cross-section area.
* Return 1.0 with volumetric off or a diameter of 0.0.
*/
inline float calculate_volumetric_multiplier(const float &diameter) {
return (parser.volumetric_enabled && diameter) ? 1.0f / CIRCLE_AREA(diameter * 0.5) : 1.0;
}
/**
* Convert the filament sizes into volumetric multipliers.
* The multiplier converts a given E value into a length.
*/
void Planner::calculate_volumetric_multipliers() {
for (uint8_t i = 0; i < COUNT(filament_size); i++) {
volumetric_multiplier[i] = calculate_volumetric_multiplier(filament_size[i]);
refresh_e_factor(i);
}
}
#endif // !NO_VOLUMETRICS
#if ENABLED(FILAMENT_WIDTH_SENSOR)
/**
* Convert the ratio value given by the filament width sensor
* into a volumetric multiplier. Conversion differs when using
* linear extrusion vs volumetric extrusion.
*/
void Planner::calculate_volumetric_for_width_sensor(const int8_t encoded_ratio) {
// Reconstitute the nominal/measured ratio
const float nom_meas_ratio = 1 + 0.01f * encoded_ratio,
ratio_2 = sq(nom_meas_ratio);
volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] = parser.volumetric_enabled
? ratio_2 / CIRCLE_AREA(filament_width_nominal * 0.5f) // Volumetric uses a true volumetric multiplier
: ratio_2; // Linear squares the ratio, which scales the volume
refresh_e_factor(FILAMENT_SENSOR_EXTRUDER_NUM);
}
#endif
#if PLANNER_LEVELING || HAS_UBL_AND_CURVES
/**
* rx, ry, rz - Cartesian positions in mm
* Leveled XYZ on completion
*/
void Planner::apply_leveling(float &rx, float &ry, float &rz) {
#if ENABLED(SKEW_CORRECTION)
skew(rx, ry, rz);
#endif
if (!leveling_active) return;
#if ABL_PLANAR
float dx = rx - (X_TILT_FULCRUM),
dy = ry - (Y_TILT_FULCRUM);
apply_rotation_xyz(bed_level_matrix, dx, dy, rz);
rx = dx + X_TILT_FULCRUM;
ry = dy + Y_TILT_FULCRUM;
#elif HAS_MESH
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
const float fade_scaling_factor = fade_scaling_factor_for_z(rz);
#else
constexpr float fade_scaling_factor = 1.0;
#endif
#if ENABLED(AUTO_BED_LEVELING_BILINEAR)
const float raw[XYZ] = { rx, ry, 0 };
#endif
rz += (
#if ENABLED(MESH_BED_LEVELING)
mbl.get_z(rx, ry
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
, fade_scaling_factor
#endif
)
#elif ENABLED(AUTO_BED_LEVELING_UBL)
fade_scaling_factor ? fade_scaling_factor * ubl.get_z_correction(rx, ry) : 0.0
#elif ENABLED(AUTO_BED_LEVELING_BILINEAR)
fade_scaling_factor ? fade_scaling_factor * bilinear_z_offset(raw) : 0.0
#endif
);
#endif
}
#endif
#if PLANNER_LEVELING
void Planner::unapply_leveling(float raw[XYZ]) {
if (leveling_active) {
#if ABL_PLANAR
matrix_3x3 inverse = matrix_3x3::transpose(bed_level_matrix);
float dx = raw[X_AXIS] - (X_TILT_FULCRUM),
dy = raw[Y_AXIS] - (Y_TILT_FULCRUM);
apply_rotation_xyz(inverse, dx, dy, raw[Z_AXIS]);
raw[X_AXIS] = dx + X_TILT_FULCRUM;
raw[Y_AXIS] = dy + Y_TILT_FULCRUM;
#elif HAS_MESH
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
const float fade_scaling_factor = fade_scaling_factor_for_z(raw[Z_AXIS]);
#else
constexpr float fade_scaling_factor = 1.0;
#endif
raw[Z_AXIS] -= (
#if ENABLED(MESH_BED_LEVELING)
mbl.get_z(raw[X_AXIS], raw[Y_AXIS]
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
, fade_scaling_factor
#endif
)
#elif ENABLED(AUTO_BED_LEVELING_UBL)
fade_scaling_factor ? fade_scaling_factor * ubl.get_z_correction(raw[X_AXIS], raw[Y_AXIS]) : 0.0
#elif ENABLED(AUTO_BED_LEVELING_BILINEAR)
fade_scaling_factor ? fade_scaling_factor * bilinear_z_offset(raw) : 0.0
#endif
);
#endif
}
#if ENABLED(SKEW_CORRECTION)
unskew(raw[X_AXIS], raw[Y_AXIS], raw[Z_AXIS]);
#endif
}
#endif // PLANNER_LEVELING
void Planner::quick_stop() {
// Remove all the queued blocks. Note that this function is NOT
// called from the Stepper ISR, so we must consider tail as readonly!
// that is why we set head to tail - But there is a race condition that
// must be handled: The tail could change between the read and the assignment
// so this must be enclosed in a critical section
const bool was_enabled = STEPPER_ISR_ENABLED();
if (was_enabled) DISABLE_STEPPER_DRIVER_INTERRUPT();
// Drop all queue entries
block_buffer_nonbusy = block_buffer_planned = block_buffer_head = block_buffer_tail;
// Restart the block delay for the first movement - As the queue was
// forced to empty, there's no risk the ISR will touch this.
delay_before_delivering = BLOCK_DELAY_FOR_1ST_MOVE;
#if ENABLED(ULTRA_LCD)
// Clear the accumulated runtime
clear_block_buffer_runtime();
#endif
// Make sure to drop any attempt of queuing moves for at least 1 second
cleaning_buffer_counter = 1000;
// Reenable Stepper ISR
if (was_enabled) ENABLE_STEPPER_DRIVER_INTERRUPT();
// And stop the stepper ISR
stepper.quick_stop();
}
void Planner::endstop_triggered(const AxisEnum axis) {
// Record stepper position and discard the current block
stepper.endstop_triggered(axis);
}
float Planner::triggered_position_mm(const AxisEnum axis) {
return stepper.triggered_position(axis) * steps_to_mm[axis];
}
void Planner::finish_and_disable() {
while (has_blocks_queued() || cleaning_buffer_counter) idle();
disable_all_steppers();
}
/**
* Get an axis position according to stepper position(s)
* For CORE machines apply translation from ABC to XYZ.
*/
float Planner::get_axis_position_mm(const AxisEnum axis) {
float axis_steps;
#if IS_CORE
// Requesting one of the "core" axes?
if (axis == CORE_AXIS_1 || axis == CORE_AXIS_2) {
// Protect the access to the position.
const bool was_enabled = STEPPER_ISR_ENABLED();
if (was_enabled) DISABLE_STEPPER_DRIVER_INTERRUPT();
// ((a1+a2)+(a1-a2))/2 -> (a1+a2+a1-a2)/2 -> (a1+a1)/2 -> a1
// ((a1+a2)-(a1-a2))/2 -> (a1+a2-a1+a2)/2 -> (a2+a2)/2 -> a2
axis_steps = 0.5f * (
axis == CORE_AXIS_2 ? CORESIGN(stepper.position(CORE_AXIS_1) - stepper.position(CORE_AXIS_2))
: stepper.position(CORE_AXIS_1) + stepper.position(CORE_AXIS_2)
);
if (was_enabled) ENABLE_STEPPER_DRIVER_INTERRUPT();
}
else
axis_steps = stepper.position(axis);
#else
axis_steps = stepper.position(axis);
#endif
#if ENABLED(LINE_BUILDUP_COMPENSATION_FEATURE)
if (axis != E_AXIS) return (sq(axis_steps / k0[axis] + sqrtk1[axis]) - k1[axis]) / k2[axis];
#endif
return axis_steps * steps_to_mm[axis];
}
/**
* Block until all buffered steps are executed / cleaned
*/
void Planner::synchronize() { while (has_blocks_queued() || cleaning_buffer_counter) idle(); }
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
#define COUNT_MOVE count_it
#else
#define COUNT_MOVE true
#endif
/**
* Planner::_buffer_steps
*
* Add a new linear movement to the planner queue (in terms of steps).
*
* target - target position in steps units
* target_float - target position in mm (HAS_POSITION_FLOAT)
* fr_mm_s - (target) speed of the move
* extruder - target extruder
* millimeters - the length of the movement, if known
* count_it - apply this move to the counters (UNREGISTERED_MOVE_SUPPORT)
*
* Returns true if movement was properly queued, false otherwise
*/
bool Planner::_buffer_steps(const int32_t (&target)[NUM_AXIS]
#if HAS_POSITION_FLOAT
, const float (&target_float)[NUM_AXIS]
#endif
, float fr_mm_s, const uint8_t extruder, const float &millimeters/*=0.0*/
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
, const bool count_it/*=true*/
#endif
) {
// If we are cleaning, do not accept queuing of movements
if (cleaning_buffer_counter) return false;
// Wait for the next available block
uint8_t next_buffer_head;
block_t * const block = get_next_free_block(next_buffer_head);
// Fill the block with the specified movement
if (!_populate_block(block, false, target
#if HAS_POSITION_FLOAT
, target_float
#endif
, fr_mm_s, extruder, millimeters
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
, count_it
#endif
)) {
// Movement was not queued, probably because it was too short.
// Simply accept that as movement queued and done
return true;
}
// If this is the first added movement, reload the delay, otherwise, cancel it.
if (block_buffer_head == block_buffer_tail) {
// If it was the first queued block, restart the 1st block delivery delay, to
// give the planner an opportunity to queue more movements and plan them
// As there are no queued movements, the Stepper ISR will not touch this
// variable, so there is no risk setting this here (but it MUST be done
// before the following line!!)
delay_before_delivering = BLOCK_DELAY_FOR_1ST_MOVE;
}
// Move buffer head
block_buffer_head = next_buffer_head;
// Recalculate and optimize trapezoidal speed profiles
recalculate();
// Movement successfully queued!
return true;
}
/**
* Planner::_populate_block
*
* Fills a new linear movement in the block (in terms of steps).
*
* target - target position in steps units
* target_float - target position in mm (HAS_POSITION_FLOAT)
* fr_mm_s - (target) speed of the move
* extruder - target extruder
* millimeters - the length of the movement, if known
* count_it - apply this move to the counters (UNREGISTERED_MOVE_SUPPORT)
*
* Returns true is movement is acceptable, false otherwise
*/
bool Planner::_populate_block(block_t * const block, bool split_move,
const int32_t (&target)[NUM_AXIS]
#if HAS_POSITION_FLOAT
, const float (&target_float)[NUM_AXIS]
#endif
, float fr_mm_s, const uint8_t extruder, const float &millimeters/*=0.0*/
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
, const bool count_it/*=true*/
#endif
) {
const int32_t da = target[A_AXIS] - position[A_AXIS],
db = target[B_AXIS] - position[B_AXIS],
dc = target[C_AXIS] - position[C_AXIS]
#if ENABLED(HANGPRINTER)
, dd = target[D_AXIS] - position[D_AXIS]
#endif
;
int32_t de = target[E_AXIS] - position[E_AXIS];
/* <-- add a slash to enable
SERIAL_ECHOPAIR(" _populate_block FR:", fr_mm_s);
SERIAL_ECHOPAIR(" A:", target[A_AXIS]);
SERIAL_ECHOPAIR(" (", da);
SERIAL_ECHOPAIR(" steps) B:", target[B_AXIS]);
SERIAL_ECHOPAIR(" (", db);
SERIAL_ECHOPAIR(" steps) C:", target[C_AXIS]);
SERIAL_ECHOPAIR(" (", dc);
SERIAL_ECHOPAIR(" steps) E:", target[E_AXIS]);
SERIAL_ECHOPAIR(" (", de);
SERIAL_ECHOLNPGM(" steps)");
//*/
#if ENABLED(PREVENT_COLD_EXTRUSION) || ENABLED(PREVENT_LENGTHY_EXTRUDE)
if (de) {
#if ENABLED(PREVENT_COLD_EXTRUSION)
if (thermalManager.tooColdToExtrude(extruder)) {
if (COUNT_MOVE) {
position[E_AXIS] = target[E_AXIS]; // Behave as if the move really took place, but ignore E part
#if HAS_POSITION_FLOAT
position_float[E_AXIS] = target_float[E_AXIS];
#endif
}
de = 0; // no difference
SERIAL_ECHO_START();
SERIAL_ECHOLNPGM(MSG_ERR_COLD_EXTRUDE_STOP);
}
#endif // PREVENT_COLD_EXTRUSION
#if ENABLED(PREVENT_LENGTHY_EXTRUDE)
if (ABS(de * e_factor[extruder]) > (int32_t)axis_steps_per_mm[E_AXIS_N] * (EXTRUDE_MAXLENGTH)) { // It's not important to get max. extrusion length in a precision < 1mm, so save some cycles and cast to int
if (COUNT_MOVE) {
position[E_AXIS] = target[E_AXIS]; // Behave as if the move really took place, but ignore E part
#if HAS_POSITION_FLOAT
position_float[E_AXIS] = target_float[E_AXIS];
#endif
}
de = 0; // no difference
SERIAL_ECHO_START();
SERIAL_ECHOLNPGM(MSG_ERR_LONG_EXTRUDE_STOP);
}
#endif // PREVENT_LENGTHY_EXTRUDE
}
#endif // PREVENT_COLD_EXTRUSION || PREVENT_LENGTHY_EXTRUDE
// Compute direction bit-mask for this block
uint8_t dm = 0;
#if CORE_IS_XY
if (da < 0) SBI(dm, X_HEAD); // Save the real Extruder (head) direction in X Axis
if (db < 0) SBI(dm, Y_HEAD); // ...and Y
if (dc < 0) SBI(dm, Z_AXIS);
if (da + db < 0) SBI(dm, A_AXIS); // Motor A direction
if (CORESIGN(da - db) < 0) SBI(dm, B_AXIS); // Motor B direction
#elif CORE_IS_XZ
if (da < 0) SBI(dm, X_HEAD); // Save the real Extruder (head) direction in X Axis
if (db < 0) SBI(dm, Y_AXIS);
if (dc < 0) SBI(dm, Z_HEAD); // ...and Z
if (da + dc < 0) SBI(dm, A_AXIS); // Motor A direction
if (CORESIGN(da - dc) < 0) SBI(dm, C_AXIS); // Motor C direction
#elif CORE_IS_YZ
if (da < 0) SBI(dm, X_AXIS);
if (db < 0) SBI(dm, Y_HEAD); // Save the real Extruder (head) direction in Y Axis
if (dc < 0) SBI(dm, Z_HEAD); // ...and Z
if (db + dc < 0) SBI(dm, B_AXIS); // Motor B direction
if (CORESIGN(db - dc) < 0) SBI(dm, C_AXIS); // Motor C direction
#elif ENABLED(HANGPRINTER)
if (da < 0) SBI(dm, A_AXIS);
if (db < 0) SBI(dm, B_AXIS);
if (dc < 0) SBI(dm, C_AXIS);
if (dd < 0) SBI(dm, D_AXIS);
#else
if (da < 0) SBI(dm, X_AXIS);
if (db < 0) SBI(dm, Y_AXIS);
if (dc < 0) SBI(dm, Z_AXIS);
#endif
if (de < 0) SBI(dm, E_AXIS);
const float esteps_float = de * e_factor[extruder];
const uint32_t esteps = ABS(esteps_float) + 0.5f;
// Clear all flags, including the "busy" bit
block->flag = 0x00;
// Set direction bits
block->direction_bits = dm;
// Specify if block is to be counted or not
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
block->count_it = count_it;
#endif
// Number of steps for each axis
// See http://www.corexy.com/theory.html
#if CORE_IS_XY
block->steps[A_AXIS] = ABS(da + db);
block->steps[B_AXIS] = ABS(da - db);
block->steps[Z_AXIS] = ABS(dc);
#elif CORE_IS_XZ
block->steps[A_AXIS] = ABS(da + dc);
block->steps[Y_AXIS] = ABS(db);
block->steps[C_AXIS] = ABS(da - dc);
#elif CORE_IS_YZ
block->steps[X_AXIS] = ABS(da);
block->steps[B_AXIS] = ABS(db + dc);
block->steps[C_AXIS] = ABS(db - dc);
#elif IS_SCARA
block->steps[A_AXIS] = ABS(da);
block->steps[B_AXIS] = ABS(db);
block->steps[Z_AXIS] = ABS(dc);
#elif ENABLED(HANGPRINTER)
block->steps[A_AXIS] = ABS(da);
block->steps[B_AXIS] = ABS(db);
block->steps[C_AXIS] = ABS(dc);
block->steps[D_AXIS] = ABS(dd);
#else
// default non-h-bot planning
block->steps[A_AXIS] = ABS(da);
block->steps[B_AXIS] = ABS(db);
block->steps[C_AXIS] = ABS(dc);
#endif
block->steps[E_AXIS] = esteps;
block->step_event_count = (
#if ENABLED(HANGPRINTER)
MAX5(block->steps[A_AXIS], block->steps[B_AXIS], block->steps[C_AXIS], block->steps[D_AXIS], esteps)
#else
MAX4(block->steps[A_AXIS], block->steps[B_AXIS], block->steps[C_AXIS], esteps)
#endif
);
// Bail if this is a zero-length block
if (block->step_event_count < MIN_STEPS_PER_SEGMENT) return false;
// For a mixing extruder, get a magnified esteps for each
#if ENABLED(MIXING_EXTRUDER)
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
block->mix_steps[i] = mixing_factor[i] * esteps;
#endif
#if FAN_COUNT > 0
for (uint8_t i = 0; i < FAN_COUNT; i++) block->fan_speed[i] = fanSpeeds[i];
#endif
#if ENABLED(BARICUDA)
block->valve_pressure = baricuda_valve_pressure;
block->e_to_p_pressure = baricuda_e_to_p_pressure;
#endif
block->active_extruder = extruder;
#if ENABLED(AUTO_POWER_CONTROL)
if (block->steps[X_AXIS] || block->steps[Y_AXIS] || block->steps[Z_AXIS])
powerManager.power_on();
#endif
// Enable active axes
#if CORE_IS_XY
if (block->steps[A_AXIS] || block->steps[B_AXIS]) {
enable_X();
enable_Y();
}
#if DISABLED(Z_LATE_ENABLE)
if (block->steps[Z_AXIS]) enable_Z();
#endif
#elif CORE_IS_XZ
if (block->steps[A_AXIS] || block->steps[C_AXIS]) {
enable_X();
enable_Z();
}
if (block->steps[Y_AXIS]) enable_Y();
#elif CORE_IS_YZ
if (block->steps[B_AXIS] || block->steps[C_AXIS]) {
enable_Y();
enable_Z();
}
if (block->steps[X_AXIS]) enable_X();
#elif DISABLED(HANGPRINTER) // Hangprinters X, Y, Z, E0 axes should always be enabled anyways
if (block->steps[X_AXIS]) enable_X();
if (block->steps[Y_AXIS]) enable_Y();
#if DISABLED(Z_LATE_ENABLE)
if (block->steps[Z_AXIS]) enable_Z();
#endif
#endif
// Enable extruder(s)
if (esteps) {
#if ENABLED(AUTO_POWER_CONTROL)
powerManager.power_on();
#endif
#if ENABLED(DISABLE_INACTIVE_EXTRUDER) // Enable only the selected extruder
#define DISABLE_IDLE_E(N) if (!g_uc_extruder_last_move[N]) disable_E##N();
for (uint8_t i = 0; i < EXTRUDERS; i++)
if (g_uc_extruder_last_move[i] > 0) g_uc_extruder_last_move[i]--;
switch (extruder) {
case 0:
#if EXTRUDERS > 1
DISABLE_IDLE_E(1);
#if EXTRUDERS > 2
DISABLE_IDLE_E(2);
#if EXTRUDERS > 3
DISABLE_IDLE_E(3);
#if EXTRUDERS > 4
DISABLE_IDLE_E(4);
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
#endif // EXTRUDERS > 1
enable_E0();
g_uc_extruder_last_move[0] = (BLOCK_BUFFER_SIZE) * 2;
#if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
if (extruder_duplication_enabled) {
enable_E1();
g_uc_extruder_last_move[1] = (BLOCK_BUFFER_SIZE) * 2;
}
#endif
break;
#if EXTRUDERS > 1
case 1:
DISABLE_IDLE_E(0);
#if EXTRUDERS > 2
DISABLE_IDLE_E(2);
#if EXTRUDERS > 3
DISABLE_IDLE_E(3);
#if EXTRUDERS > 4
DISABLE_IDLE_E(4);
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
enable_E1();
g_uc_extruder_last_move[1] = (BLOCK_BUFFER_SIZE) * 2;
break;
#if EXTRUDERS > 2
case 2:
DISABLE_IDLE_E(0);
DISABLE_IDLE_E(1);
#if EXTRUDERS > 3
DISABLE_IDLE_E(3);
#if EXTRUDERS > 4
DISABLE_IDLE_E(4);
#endif
#endif
enable_E2();
g_uc_extruder_last_move[2] = (BLOCK_BUFFER_SIZE) * 2;
break;
#if EXTRUDERS > 3
case 3:
DISABLE_IDLE_E(0);
DISABLE_IDLE_E(1);
DISABLE_IDLE_E(2);
#if EXTRUDERS > 4
DISABLE_IDLE_E(4);
#endif
enable_E3();
g_uc_extruder_last_move[3] = (BLOCK_BUFFER_SIZE) * 2;
break;
#if EXTRUDERS > 4
case 4:
DISABLE_IDLE_E(0);
DISABLE_IDLE_E(1);
DISABLE_IDLE_E(2);
DISABLE_IDLE_E(3);
enable_E4();
g_uc_extruder_last_move[4] = (BLOCK_BUFFER_SIZE) * 2;
break;
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
#endif // EXTRUDERS > 1
}
#else
enable_E0();
enable_E1();
enable_E2();
enable_E3();
enable_E4();
#endif
}
if (esteps)
NOLESS(fr_mm_s, min_feedrate_mm_s);
else
NOLESS(fr_mm_s, min_travel_feedrate_mm_s);
/**
* This part of the code calculates the total length of the movement.
* For cartesian bots, the X_AXIS is the real X movement and same for Y_AXIS.
* But for corexy bots, that is not true. The "X_AXIS" and "Y_AXIS" motors (that should be named to A_AXIS
* and B_AXIS) cannot be used for X and Y length, because A=X+Y and B=X-Y.
* So we need to create other 2 "AXIS", named X_HEAD and Y_HEAD, meaning the real displacement of the Head.
* Having the real displacement of the head, we can calculate the total movement length and apply the desired speed.
*/
#if IS_CORE
float delta_mm[Z_HEAD + 1];
#if CORE_IS_XY
delta_mm[X_HEAD] = da * steps_to_mm[A_AXIS];
delta_mm[Y_HEAD] = db * steps_to_mm[B_AXIS];
delta_mm[Z_AXIS] = dc * steps_to_mm[Z_AXIS];
delta_mm[A_AXIS] = (da + db) * steps_to_mm[A_AXIS];
delta_mm[B_AXIS] = CORESIGN(da - db) * steps_to_mm[B_AXIS];
#elif CORE_IS_XZ
delta_mm[X_HEAD] = da * steps_to_mm[A_AXIS];
delta_mm[Y_AXIS] = db * steps_to_mm[Y_AXIS];
delta_mm[Z_HEAD] = dc * steps_to_mm[C_AXIS];
delta_mm[A_AXIS] = (da + dc) * steps_to_mm[A_AXIS];
delta_mm[C_AXIS] = CORESIGN(da - dc) * steps_to_mm[C_AXIS];
#elif CORE_IS_YZ
delta_mm[X_AXIS] = da * steps_to_mm[X_AXIS];
delta_mm[Y_HEAD] = db * steps_to_mm[B_AXIS];
delta_mm[Z_HEAD] = dc * steps_to_mm[C_AXIS];
delta_mm[B_AXIS] = (db + dc) * steps_to_mm[B_AXIS];
delta_mm[C_AXIS] = CORESIGN(db - dc) * steps_to_mm[C_AXIS];
#endif
#else
float delta_mm[NUM_AXIS];
delta_mm[A_AXIS] = da * steps_to_mm[A_AXIS];
delta_mm[B_AXIS] = db * steps_to_mm[B_AXIS];
delta_mm[C_AXIS] = dc * steps_to_mm[C_AXIS];
#if ENABLED(HANGPRINTER)
delta_mm[D_AXIS] = dd * steps_to_mm[D_AXIS];
#endif
#endif
delta_mm[E_AXIS] = esteps_float * steps_to_mm[E_AXIS_N];
if (block->steps[A_AXIS] < MIN_STEPS_PER_SEGMENT && block->steps[B_AXIS] < MIN_STEPS_PER_SEGMENT && block->steps[C_AXIS] < MIN_STEPS_PER_SEGMENT
#if ENABLED(HANGPRINTER)
&& block->steps[D_AXIS] < MIN_STEPS_PER_SEGMENT
#endif
) {
block->millimeters = ABS(delta_mm[E_AXIS]);
}
else if (!millimeters) {
block->millimeters = SQRT(
#if CORE_IS_XY
sq(delta_mm[X_HEAD]) + sq(delta_mm[Y_HEAD]) + sq(delta_mm[Z_AXIS])
#elif CORE_IS_XZ
sq(delta_mm[X_HEAD]) + sq(delta_mm[Y_AXIS]) + sq(delta_mm[Z_HEAD])
#elif CORE_IS_YZ
sq(delta_mm[X_AXIS]) + sq(delta_mm[Y_HEAD]) + sq(delta_mm[Z_HEAD])
#elif ENABLED(HANGPRINTER)
sq(delta_mm[A_AXIS]) + sq(delta_mm[B_AXIS]) + sq(delta_mm[C_AXIS]) + sq(delta_mm[D_AXIS])
#else
sq(delta_mm[X_AXIS]) + sq(delta_mm[Y_AXIS]) + sq(delta_mm[Z_AXIS])
#endif
);
}
else
block->millimeters = millimeters;
const float inverse_millimeters = 1.0f / block->millimeters; // Inverse millimeters to remove multiple divides
// Calculate inverse time for this move. No divide by zero due to previous checks.
// Example: At 120mm/s a 60mm move takes 0.5s. So this will give 2.0.
float inverse_secs = fr_mm_s * inverse_millimeters;
// Get the number of non busy movements in queue (non busy means that they can be altered)
const uint8_t moves_queued = nonbusy_movesplanned();
// Slow down when the buffer starts to empty, rather than wait at the corner for a buffer refill
#if ENABLED(SLOWDOWN) || ENABLED(ULTRA_LCD) || defined(XY_FREQUENCY_LIMIT)
// Segment time im micro seconds
uint32_t segment_time_us = LROUND(1000000.0f / inverse_secs);
#endif
#if ENABLED(SLOWDOWN)
if (WITHIN(moves_queued, 2, (BLOCK_BUFFER_SIZE) / 2 - 1)) {
if (segment_time_us < min_segment_time_us) {
// buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
const uint32_t nst = segment_time_us + LROUND(2 * (min_segment_time_us - segment_time_us) / moves_queued);
inverse_secs = 1000000.0f / nst;
#if defined(XY_FREQUENCY_LIMIT) || ENABLED(ULTRA_LCD)
segment_time_us = nst;
#endif
}
}
#endif
#if ENABLED(ULTRA_LCD)
// Protect the access to the position.
const bool was_enabled = STEPPER_ISR_ENABLED();
if (was_enabled) DISABLE_STEPPER_DRIVER_INTERRUPT();
block_buffer_runtime_us += segment_time_us;
if (was_enabled) ENABLE_STEPPER_DRIVER_INTERRUPT();
#endif
block->nominal_speed_sqr = sq(block->millimeters * inverse_secs); // (mm/sec)^2 Always > 0
block->nominal_rate = CEIL(block->step_event_count * inverse_secs); // (step/sec) Always > 0
#if ENABLED(FILAMENT_WIDTH_SENSOR)
static float filwidth_e_count = 0, filwidth_delay_dist = 0;
//FMM update ring buffer used for delay with filament measurements
if (extruder == FILAMENT_SENSOR_EXTRUDER_NUM && filwidth_delay_index[1] >= 0) { //only for extruder with filament sensor and if ring buffer is initialized
constexpr int MMD_CM = MAX_MEASUREMENT_DELAY + 1, MMD_MM = MMD_CM * 10;
// increment counters with next move in e axis
filwidth_e_count += delta_mm[E_AXIS];
filwidth_delay_dist += delta_mm[E_AXIS];
// Only get new measurements on forward E movement
if (!UNEAR_ZERO(filwidth_e_count)) {
// Loop the delay distance counter (modulus by the mm length)
while (filwidth_delay_dist >= MMD_MM) filwidth_delay_dist -= MMD_MM;
// Convert into an index into the measurement array
filwidth_delay_index[0] = int8_t(filwidth_delay_dist * 0.1f);
// If the index has changed (must have gone forward)...
if (filwidth_delay_index[0] != filwidth_delay_index[1]) {
filwidth_e_count = 0; // Reset the E movement counter
const int8_t meas_sample = thermalManager.widthFil_to_size_ratio();
do {
filwidth_delay_index[1] = (filwidth_delay_index[1] + 1) % MMD_CM; // The next unused slot
measurement_delay[filwidth_delay_index[1]] = meas_sample; // Store the measurement
} while (filwidth_delay_index[0] != filwidth_delay_index[1]); // More slots to fill?
}
}
}
#endif
// Calculate and limit speed in mm/sec for each axis
float current_speed[NUM_AXIS], speed_factor = 1.0f; // factor <1 decreases speed
LOOP_NUM_AXIS(i) {
const float cs = ABS((current_speed[i] = delta_mm[i] * inverse_secs));
#if ENABLED(DISTINCT_E_FACTORS)
if (i == E_AXIS) i += extruder;
#endif
if (cs > max_feedrate_mm_s[i]) NOMORE(speed_factor, max_feedrate_mm_s[i] / cs);
}
// Max segment time in µs.
#ifdef XY_FREQUENCY_LIMIT
// Check and limit the xy direction change frequency
const unsigned char direction_change = block->direction_bits ^ old_direction_bits;
old_direction_bits = block->direction_bits;
segment_time_us = LROUND((float)segment_time_us / speed_factor);
uint32_t xs0 = axis_segment_time_us[X_AXIS][0],
xs1 = axis_segment_time_us[X_AXIS][1],
xs2 = axis_segment_time_us[X_AXIS][2],
ys0 = axis_segment_time_us[Y_AXIS][0],
ys1 = axis_segment_time_us[Y_AXIS][1],
ys2 = axis_segment_time_us[Y_AXIS][2];
if (TEST(direction_change, X_AXIS)) {
xs2 = axis_segment_time_us[X_AXIS][2] = xs1;
xs1 = axis_segment_time_us[X_AXIS][1] = xs0;
xs0 = 0;
}
xs0 = axis_segment_time_us[X_AXIS][0] = xs0 + segment_time_us;
if (TEST(direction_change, Y_AXIS)) {
ys2 = axis_segment_time_us[Y_AXIS][2] = axis_segment_time_us[Y_AXIS][1];
ys1 = axis_segment_time_us[Y_AXIS][1] = axis_segment_time_us[Y_AXIS][0];
ys0 = 0;
}
ys0 = axis_segment_time_us[Y_AXIS][0] = ys0 + segment_time_us;
const uint32_t max_x_segment_time = MAX3(xs0, xs1, xs2),
max_y_segment_time = MAX3(ys0, ys1, ys2),
min_xy_segment_time = MIN(max_x_segment_time, max_y_segment_time);
if (min_xy_segment_time < MAX_FREQ_TIME_US) {
const float low_sf = speed_factor * min_xy_segment_time / (MAX_FREQ_TIME_US);
NOMORE(speed_factor, low_sf);
}
#endif // XY_FREQUENCY_LIMIT
// Correct the speed
if (speed_factor < 1.0f) {
LOOP_NUM_AXIS(i) current_speed[i] *= speed_factor;
block->nominal_rate *= speed_factor;
block->nominal_speed_sqr = block->nominal_speed_sqr * sq(speed_factor);
}
// Compute and limit the acceleration rate for the trapezoid generator.
const float steps_per_mm = block->step_event_count * inverse_millimeters;
uint32_t accel;
if (!block->steps[A_AXIS] && !block->steps[B_AXIS] && !block->steps[C_AXIS]
#if ENABLED(HANGPRINTER)
&& !block->steps[D_AXIS]
#endif
) {
// convert to: acceleration steps/sec^2
accel = CEIL(retract_acceleration * steps_per_mm);
#if ENABLED(LIN_ADVANCE)
block->use_advance_lead = false;
#endif
}
else {
#define LIMIT_ACCEL_LONG(AXIS,INDX) do{ \
if (block->steps[AXIS] && max_acceleration_steps_per_s2[AXIS+INDX] < accel) { \
const uint32_t comp = max_acceleration_steps_per_s2[AXIS+INDX] * block->step_event_count; \
if (accel * block->steps[AXIS] > comp) accel = comp / block->steps[AXIS]; \
} \
}while(0)
#define LIMIT_ACCEL_FLOAT(AXIS,INDX) do{ \
if (block->steps[AXIS] && max_acceleration_steps_per_s2[AXIS+INDX] < accel) { \
const float comp = (float)max_acceleration_steps_per_s2[AXIS+INDX] * (float)block->step_event_count; \
if ((float)accel * (float)block->steps[AXIS] > comp) accel = comp / (float)block->steps[AXIS]; \
} \
}while(0)
// Start with print or travel acceleration
accel = CEIL((esteps ? acceleration : travel_acceleration) * steps_per_mm);
#if ENABLED(LIN_ADVANCE)
#if ENABLED(JUNCTION_DEVIATION)
#if ENABLED(DISTINCT_E_FACTORS)
#define MAX_E_JERK max_e_jerk[extruder]
#else
#define MAX_E_JERK max_e_jerk
#endif
#else
#define MAX_E_JERK max_jerk[E_AXIS]
#endif
/**
*
* Use LIN_ADVANCE for blocks if all these are true:
*
* esteps : This is a print move, because we checked for A, B, C steps before.
*
* extruder_advance_K : There is an advance factor set.
*
* de > 0 : Extruder is running forward (e.g., for "Wipe while retracting" (Slic3r) or "Combing" (Cura) moves)
*/
block->use_advance_lead = esteps
&& extruder_advance_K
&& de > 0;
if (block->use_advance_lead) {
block->e_D_ratio = (target_float[E_AXIS] - position_float[E_AXIS]) /
#if IS_KINEMATIC
block->millimeters
#else
SQRT(sq(target_float[X_AXIS] - position_float[X_AXIS])
+ sq(target_float[Y_AXIS] - position_float[Y_AXIS])
+ sq(target_float[Z_AXIS] - position_float[Z_AXIS]))
#endif
;
// Check for unusual high e_D ratio to detect if a retract move was combined with the last print move due to min. steps per segment. Never execute this with advance!
// This assumes no one will use a retract length of 0mm < retr_length < ~0.2mm and no one will print 100mm wide lines using 3mm filament or 35mm wide lines using 1.75mm filament.
if (block->e_D_ratio > 3.0f)
block->use_advance_lead = false;
else {
const uint32_t max_accel_steps_per_s2 = MAX_E_JERK / (extruder_advance_K * block->e_D_ratio) * steps_per_mm;
#if ENABLED(LA_DEBUG)
if (accel > max_accel_steps_per_s2) SERIAL_ECHOLNPGM("Acceleration limited.");
#endif
NOMORE(accel, max_accel_steps_per_s2);
}
}
#endif
#if ENABLED(DISTINCT_E_FACTORS)
#define ACCEL_IDX extruder
#else
#define ACCEL_IDX 0
#endif
// Limit acceleration per axis
if (block->step_event_count <= cutoff_long) {
LIMIT_ACCEL_LONG(A_AXIS, 0);
LIMIT_ACCEL_LONG(B_AXIS, 0);
LIMIT_ACCEL_LONG(C_AXIS, 0);
#if ENABLED(HANGPRINTER)
LIMIT_ACCEL_LONG(D_AXIS, 0);
#endif
LIMIT_ACCEL_LONG(E_AXIS, ACCEL_IDX);
}
else {
LIMIT_ACCEL_FLOAT(A_AXIS, 0);
LIMIT_ACCEL_FLOAT(B_AXIS, 0);
LIMIT_ACCEL_FLOAT(C_AXIS, 0);
#if ENABLED(HANGPRINTER)
LIMIT_ACCEL_FLOAT(D_AXIS, 0);
#endif
LIMIT_ACCEL_FLOAT(E_AXIS, ACCEL_IDX);
}
}
block->acceleration_steps_per_s2 = accel;
block->acceleration = accel / steps_per_mm;
#if DISABLED(S_CURVE_ACCELERATION)
block->acceleration_rate = (uint32_t)(accel * (4096.0f * 4096.0f / (STEPPER_TIMER_RATE)));
#endif
#if ENABLED(LIN_ADVANCE)
if (block->use_advance_lead) {
block->advance_speed = (STEPPER_TIMER_RATE) / (extruder_advance_K * block->e_D_ratio * block->acceleration * axis_steps_per_mm[E_AXIS_N]);
#if ENABLED(LA_DEBUG)
if (extruder_advance_K * block->e_D_ratio * block->acceleration * 2 < SQRT(block->nominal_speed_sqr) * block->e_D_ratio)
SERIAL_ECHOLNPGM("More than 2 steps per eISR loop executed.");
if (block->advance_speed < 200)
SERIAL_ECHOLNPGM("eISR running at > 10kHz.");
#endif
}
#endif
float vmax_junction_sqr; // Initial limit on the segment entry velocity (mm/s)^2
#if ENABLED(JUNCTION_DEVIATION)
/**
* Compute maximum allowable entry speed at junction by centripetal acceleration approximation.
* Let a circle be tangent to both previous and current path line segments, where the junction
* deviation is defined as the distance from the junction to the closest edge of the circle,
* colinear with the circle center. The circular segment joining the two paths represents the
* path of centripetal acceleration. Solve for max velocity based on max acceleration about the
* radius of the circle, defined indirectly by junction deviation. This may be also viewed as
* path width or max_jerk in the previous Grbl version. This approach does not actually deviate
* from path, but used as a robust way to compute cornering speeds, as it takes into account the
* nonlinearities of both the junction angle and junction velocity.
*
* NOTE: If the junction deviation value is finite, Grbl executes the motions in an exact path
* mode (G61). If the junction deviation value is zero, Grbl will execute the motion in an exact
* stop mode (G61.1) manner. In the future, if continuous mode (G64) is desired, the math here
* is exactly the same. Instead of motioning all the way to junction point, the machine will
* just follow the arc circle defined here. The Arduino doesn't have the CPU cycles to perform
* a continuous mode path, but ARM-based microcontrollers most certainly do.
*
* NOTE: The max junction speed is a fixed value, since machine acceleration limits cannot be
* changed dynamically during operation nor can the line move geometry. This must be kept in
* memory in the event of a feedrate override changing the nominal speeds of blocks, which can
* change the overall maximum entry speed conditions of all blocks.
*
* #######
* https://github.com/MarlinFirmware/Marlin/issues/10341#issuecomment-388191754
*
* hoffbaked: on May 10 2018 tuned and improved the GRBL algorithm for Marlin:
Okay! It seems to be working good. I somewhat arbitrarily cut it off at 1mm
on then on anything with less sides than an octagon. With this, and the
reverse pass actually recalculating things, a corner acceleration value
of 1000 junction deviation of .05 are pretty reasonable. If the cycles
can be spared, a better acos could be used. For all I know, it may be
already calculated in a different place. */
// Unit vector of previous path line segment
static float previous_unit_vec[XYZE];
float unit_vec[] = {
delta_mm[A_AXIS] * inverse_millimeters,
delta_mm[B_AXIS] * inverse_millimeters,
delta_mm[C_AXIS] * inverse_millimeters,
delta_mm[E_AXIS] * inverse_millimeters
};
// Skip first block or when previous_nominal_speed is used as a flag for homing and offset cycles.
if (moves_queued && !UNEAR_ZERO(previous_nominal_speed_sqr)) {
// Compute cosine of angle between previous and current path. (prev_unit_vec is negative)
// NOTE: Max junction velocity is computed without sin() or acos() by trig half angle identity.
float junction_cos_theta = -previous_unit_vec[X_AXIS] * unit_vec[X_AXIS]
-previous_unit_vec[Y_AXIS] * unit_vec[Y_AXIS]
-previous_unit_vec[Z_AXIS] * unit_vec[Z_AXIS]
-previous_unit_vec[E_AXIS] * unit_vec[E_AXIS]
;
// NOTE: Computed without any expensive trig, sin() or acos(), by trig half angle identity of cos(theta).
if (junction_cos_theta > 0.999999f) {
// For a 0 degree acute junction, just set minimum junction speed.
vmax_junction_sqr = sq(float(MINIMUM_PLANNER_SPEED));
}
else {
NOLESS(junction_cos_theta, -0.999999f); // Check for numerical round-off to avoid divide by zero.
// Convert delta vector to unit vector
float junction_unit_vec[XYZE] = {
unit_vec[X_AXIS] - previous_unit_vec[X_AXIS],
unit_vec[Y_AXIS] - previous_unit_vec[Y_AXIS],
unit_vec[Z_AXIS] - previous_unit_vec[Z_AXIS],
unit_vec[E_AXIS] - previous_unit_vec[E_AXIS]
};
normalize_junction_vector(junction_unit_vec);
const float junction_acceleration = limit_value_by_axis_maximum(block->acceleration, junction_unit_vec),
sin_theta_d2 = SQRT(0.5f * (1.0f - junction_cos_theta)); // Trig half angle identity. Always positive.
vmax_junction_sqr = (junction_acceleration * junction_deviation_mm * sin_theta_d2) / (1.0f - sin_theta_d2);
if (block->millimeters < 1) {
// Fast acos approximation, minus the error bar to be safe
const float junction_theta = (RADIANS(-40) * sq(junction_cos_theta) - RADIANS(50)) * junction_cos_theta + RADIANS(90) - 0.18f;
// If angle is greater than 135 degrees (octagon), find speed for approximate arc
if (junction_theta > RADIANS(135)) {
const float limit_sqr = block->millimeters / (RADIANS(180) - junction_theta) * junction_acceleration;
NOMORE(vmax_junction_sqr, limit_sqr);
}
}
}
// Get the lowest speed
vmax_junction_sqr = MIN3(vmax_junction_sqr, block->nominal_speed_sqr, previous_nominal_speed_sqr);
}
else // Init entry speed to zero. Assume it starts from rest. Planner will correct this later.
vmax_junction_sqr = 0;
COPY(previous_unit_vec, unit_vec);
#else // Classic Jerk Limiting
/**
* Adapted from Průša MKS firmware
* https://github.com/prusa3d/Prusa-Firmware
*/
const float nominal_speed = SQRT(block->nominal_speed_sqr);
// Exit speed limited by a jerk to full halt of a previous last segment
static float previous_safe_speed;
// Start with a safe speed (from which the machine may halt to stop immediately).
float safe_speed = nominal_speed;
uint8_t limited = 0;
LOOP_NUM_AXIS(i) {
const float jerk = ABS(current_speed[i]), // cs : Starting from zero, change in speed for this axis
maxj = max_jerk[i]; // mj : The max jerk setting for this axis
if (jerk > maxj) { // cs > mj : New current speed too fast?
if (limited) { // limited already?
const float mjerk = nominal_speed * maxj; // ns*mj
if (jerk * safe_speed > mjerk) safe_speed = mjerk / jerk; // ns*mj/cs
}
else {
safe_speed *= maxj / jerk; // Initial limit: ns*mj/cs
++limited; // Initially limited
}
}
}
float vmax_junction;
if (moves_queued && !UNEAR_ZERO(previous_nominal_speed_sqr)) {
// Estimate a maximum velocity allowed at a joint of two successive segments.
// If this maximum velocity allowed is lower than the minimum of the entry / exit safe velocities,
// then the machine is not coasting anymore and the safe entry / exit velocities shall be used.
// Factor to multiply the previous / current nominal velocities to get componentwise limited velocities.
float v_factor = 1;
limited = 0;
// The junction velocity will be shared between successive segments. Limit the junction velocity to their minimum.
// Pick the smaller of the nominal speeds. Higher speed shall not be achieved at the junction during coasting.
const float previous_nominal_speed = SQRT(previous_nominal_speed_sqr);
vmax_junction = MIN(nominal_speed, previous_nominal_speed);
// Now limit the jerk in all axes.
const float smaller_speed_factor = vmax_junction / previous_nominal_speed;
LOOP_NUM_AXIS(axis) {
// Limit an axis. We have to differentiate: coasting, reversal of an axis, full stop.
float v_exit = previous_speed[axis] * smaller_speed_factor,
v_entry = current_speed[axis];
if (limited) {
v_exit *= v_factor;
v_entry *= v_factor;
}
// Calculate jerk depending on whether the axis is coasting in the same direction or reversing.
const float jerk = (v_exit > v_entry)
? // coasting axis reversal
( (v_entry > 0 || v_exit < 0) ? (v_exit - v_entry) : MAX(v_exit, -v_entry) )
: // v_exit <= v_entry coasting axis reversal
( (v_entry < 0 || v_exit > 0) ? (v_entry - v_exit) : MAX(-v_exit, v_entry) );
if (jerk > max_jerk[axis]) {
v_factor *= max_jerk[axis] / jerk;
++limited;
}
}
if (limited) vmax_junction *= v_factor;
// Now the transition velocity is known, which maximizes the shared exit / entry velocity while
// respecting the jerk factors, it may be possible, that applying separate safe exit / entry velocities will achieve faster prints.
const float vmax_junction_threshold = vmax_junction * 0.99f;
if (previous_safe_speed > vmax_junction_threshold && safe_speed > vmax_junction_threshold)
vmax_junction = safe_speed;
}
else
vmax_junction = safe_speed;
previous_safe_speed = safe_speed;
vmax_junction_sqr = sq(vmax_junction);
#endif // Classic Jerk Limiting
// Max entry speed of this block equals the max exit speed of the previous block.
block->max_entry_speed_sqr = vmax_junction_sqr;
// Initialize block entry speed. Compute based on deceleration to user-defined MINIMUM_PLANNER_SPEED.
const float v_allowable_sqr = max_allowable_speed_sqr(-block->acceleration, sq(float(MINIMUM_PLANNER_SPEED)), block->millimeters);
// If we are trying to add a split block, start with the
// max. allowed speed to avoid an interrupted first move.
block->entry_speed_sqr = !split_move ? sq(float(MINIMUM_PLANNER_SPEED)) : MIN(vmax_junction_sqr, v_allowable_sqr);
// Initialize planner efficiency flags
// Set flag if block will always reach maximum junction speed regardless of entry/exit speeds.
// If a block can de/ac-celerate from nominal speed to zero within the length of the block, then
// the current block and next block junction speeds are guaranteed to always be at their maximum
// junction speeds in deceleration and acceleration, respectively. This is due to how the current
// block nominal speed limits both the current and next maximum junction speeds. Hence, in both
// the reverse and forward planners, the corresponding block junction speed will always be at the
// the maximum junction speed and may always be ignored for any speed reduction checks.
block->flag |= block->nominal_speed_sqr <= v_allowable_sqr ? BLOCK_FLAG_RECALCULATE | BLOCK_FLAG_NOMINAL_LENGTH : BLOCK_FLAG_RECALCULATE;
// Update previous path unit_vector and nominal speed
COPY(previous_speed, current_speed);
previous_nominal_speed_sqr = block->nominal_speed_sqr;
// Update the position (only when a move was queued)
static_assert(COUNT(target) > 1, "Parameter to _populate_block must be (&target)["
#if ENABLED(HANGPRINTER)
"ABCD"
#else
"XYZ"
#endif
"E]!"
);
if (COUNT_MOVE) {
COPY(position, target);
#if HAS_POSITION_FLOAT
COPY(position_float, target_float);
#endif
}
// Movement was accepted
return true;
} // _populate_block()
/**
* Planner::buffer_sync_block
* Add a block to the buffer that just updates the position
*/
void Planner::buffer_sync_block() {
// Wait for the next available block
uint8_t next_buffer_head;
block_t * const block = get_next_free_block(next_buffer_head);
// Clear block
memset(block, 0, sizeof(block_t));
block->flag = BLOCK_FLAG_SYNC_POSITION;
block->position[A_AXIS] = position[A_AXIS];
block->position[B_AXIS] = position[B_AXIS];
block->position[C_AXIS] = position[C_AXIS];
#if ENABLED(HANGPRINTER)
block->position[D_AXIS] = position[D_AXIS];
#endif
block->position[E_AXIS] = position[E_AXIS];
// If this is the first added movement, reload the delay, otherwise, cancel it.
if (block_buffer_head == block_buffer_tail) {
// If it was the first queued block, restart the 1st block delivery delay, to
// give the planner an opportunity to queue more movements and plan them
// As there are no queued movements, the Stepper ISR will not touch this
// variable, so there is no risk setting this here (but it MUST be done
// before the following line!!)
delay_before_delivering = BLOCK_DELAY_FOR_1ST_MOVE;
}
block_buffer_head = next_buffer_head;
stepper.wake_up();
} // buffer_sync_block()
/**
* Planner::buffer_segment
*
* Add a new linear movement to the buffer in axis units.
*
* Leveling and kinematics should be applied ahead of calling this.
*
* a,b,c,e - target positions in mm and/or degrees
* fr_mm_s - (target) speed of the move
* extruder - target extruder
* millimeters - the length of the movement, if known
*/
bool Planner::buffer_segment(const float &a, const float &b, const float &c
#if ENABLED(HANGPRINTER)
, const float &d
#endif
, const float &e, const float &fr_mm_s, const uint8_t extruder, const float &millimeters/*=0.0*/
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
, bool count_it /* = true */
#endif
) {
// If we are cleaning, do not accept queuing of movements
if (cleaning_buffer_counter) return false;
// When changing extruders recalculate steps corresponding to the E position
#if ENABLED(DISTINCT_E_FACTORS)
if (last_extruder != extruder && axis_steps_per_mm[E_AXIS_N] != axis_steps_per_mm[E_AXIS + last_extruder]) {
position[E_AXIS] = LROUND(position[E_AXIS] * axis_steps_per_mm[E_AXIS_N] * steps_to_mm[E_AXIS + last_extruder]);
last_extruder = extruder;
}
#endif
// The target position of the tool in absolute steps
// Calculate target position in absolute steps
const int32_t target[NUM_AXIS] = {
#if ENABLED(LINE_BUILDUP_COMPENSATION_FEATURE)
LROUND(k0[A_AXIS] * (SQRT(k1[A_AXIS] + a * k2[A_AXIS]) - sqrtk1[A_AXIS])),
LROUND(k0[B_AXIS] * (SQRT(k1[B_AXIS] + b * k2[B_AXIS]) - sqrtk1[B_AXIS])),
LROUND(k0[C_AXIS] * (SQRT(k1[C_AXIS] + c * k2[C_AXIS]) - sqrtk1[C_AXIS])),
LROUND(k0[D_AXIS] * (SQRT(k1[D_AXIS] + d * k2[D_AXIS]) - sqrtk1[D_AXIS])),
#else
LROUND(a * axis_steps_per_mm[A_AXIS]),
LROUND(b * axis_steps_per_mm[B_AXIS]),
LROUND(c * axis_steps_per_mm[C_AXIS]),
#if ENABLED(HANGPRINTER)
LROUND(d * axis_steps_per_mm[D_AXIS]),
#endif
#endif
LROUND(e * axis_steps_per_mm[E_AXIS_N])
};
#if HAS_POSITION_FLOAT
const float target_float[NUM_AXIS] = { a, b, c
#if ENABLED(HANGPRINTER)
, d
#endif
, e
};
#endif
// DRYRUN prevents E moves from taking place
if (DEBUGGING(DRYRUN)) {
if (COUNT_MOVE) {
position[E_AXIS] = target[E_AXIS];
#if HAS_POSITION_FLOAT
position_float[E_AXIS] = e;
#endif
}
}
/* <-- add a slash to enable
SERIAL_ECHOPAIR(" buffer_segment FR:", fr_mm_s);
#if IS_KINEMATIC
SERIAL_ECHOPAIR(" A:", a);
SERIAL_ECHOPAIR(" (", position[A_AXIS]);
SERIAL_ECHOPAIR("->", target[A_AXIS]);
SERIAL_ECHOPAIR(") B:", b);
#else
SERIAL_ECHOPAIR(" X:", a);
SERIAL_ECHOPAIR(" (", position[X_AXIS]);
SERIAL_ECHOPAIR("->", target[X_AXIS]);
SERIAL_ECHOPAIR(") Y:", b);
#endif
SERIAL_ECHOPAIR(" (", position[Y_AXIS]);
SERIAL_ECHOPAIR("->", target[Y_AXIS]);
#if ENABLED(DELTA) || ENABLED(HANGPRINTER)
SERIAL_ECHOPAIR(") C:", c);
#else
SERIAL_ECHOPAIR(") Z:", c);
#endif
SERIAL_ECHOPAIR(" (", position[Z_AXIS]);
SERIAL_ECHOPAIR("->", target[Z_AXIS]);
#if ENABLED(HANGPRINTER)
SERIAL_ECHOPAIR(") D:", d);
SERIAL_ECHOPAIR(" (", position[D_AXIS]);
SERIAL_ECHOPAIR("->", target[D_AXIS]);
#endif
SERIAL_ECHOPAIR(") E:", e);
SERIAL_ECHOPAIR(" (", position[E_AXIS]);
SERIAL_ECHOPAIR("->", target[E_AXIS]);
SERIAL_ECHOLNPGM(")");
//*/
// Queue the movement
if (
!_buffer_steps(target
#if HAS_POSITION_FLOAT
, target_float
#endif
, fr_mm_s, extruder, millimeters
#if ENABLED(UNREGISTERED_MOVE_SUPPORT)
, count_it
#endif
)
) return false;
stepper.wake_up();
return true;
} // buffer_segment()
/**
* Directly set the planner XYZ position (and stepper positions)
* converting mm (or angles for SCARA) into steps.
*
* On CORE machines stepper ABC will be translated from the given XYZ.
*/
void Planner::_set_position_mm(const float &a, const float &b, const float &c
#if ENABLED(HANGPRINTER)
, const float &d
#endif
, const float &e
) {
#if ENABLED(DISTINCT_E_FACTORS)
last_extruder = active_extruder;
#endif
#if ENABLED(LINE_BUILDUP_COMPENSATION_FEATURE)
position[A_AXIS] = LROUND(k0[A_AXIS] * (SQRT(k1[A_AXIS] + a * k2[A_AXIS]) - sqrtk1[A_AXIS])),
position[B_AXIS] = LROUND(k0[B_AXIS] * (SQRT(k1[B_AXIS] + b * k2[B_AXIS]) - sqrtk1[B_AXIS])),
position[C_AXIS] = LROUND(k0[C_AXIS] * (SQRT(k1[C_AXIS] + c * k2[C_AXIS]) - sqrtk1[C_AXIS])),
position[D_AXIS] = LROUND(k0[D_AXIS] * (SQRT(k1[D_AXIS] + d * k2[D_AXIS]) - sqrtk1[D_AXIS])),
#else
position[A_AXIS] = LROUND(a * axis_steps_per_mm[A_AXIS]);
position[B_AXIS] = LROUND(b * axis_steps_per_mm[B_AXIS]);
position[C_AXIS] = LROUND(axis_steps_per_mm[C_AXIS] * (c + (
#if !IS_KINEMATIC && ENABLED(AUTO_BED_LEVELING_UBL)
leveling_active ? ubl.get_z_correction(a, b) :
#endif
0)
));
#if ENABLED(HANGPRINTER)
position[D_AXIS] = LROUND(d * axis_steps_per_mm[D_AXIS]),
#endif
#endif
position[E_AXIS] = LROUND(e * axis_steps_per_mm[_EINDEX]);
#if HAS_POSITION_FLOAT
position_float[A_AXIS] = a;
position_float[B_AXIS] = b;
position_float[C_AXIS] = c;
#if ENABLED(HANGPRINTER)
position_float[D_AXIS] = d;
#endif
position_float[E_AXIS] = e;
#endif
if (has_blocks_queued()) {
//previous_nominal_speed_sqr = 0.0; // Reset planner junction speeds. Assume start from rest.
//ZERO(previous_speed);
buffer_sync_block();
}
else
stepper.set_position(position[A_AXIS], position[B_AXIS], position[C_AXIS],
#if ENABLED(HANGPRINTER)
position[D_AXIS],
#endif
position[E_AXIS]
);
}
void Planner::set_position_mm_kinematic(const float (&cart)[XYZE]) {
#if PLANNER_LEVELING
float raw[XYZ] = { cart[X_AXIS], cart[Y_AXIS], cart[Z_AXIS] };
apply_leveling(raw);
#elif ENABLED(HANGPRINTER)
float raw[XYZ] = { cart[X_AXIS], cart[Y_AXIS], cart[Z_AXIS] };
#else
const float (&raw)[XYZE] = cart;
#endif
#if IS_KINEMATIC
inverse_kinematics(raw);
#if ENABLED(HANGPRINTER)
_set_position_mm(line_lengths[A_AXIS], line_lengths[B_AXIS], line_lengths[C_AXIS], line_lengths[D_AXIS], cart[E_CART]);
#else
_set_position_mm(delta[A_AXIS], delta[B_AXIS], delta[C_AXIS], cart[E_CART]);
#endif
#else
_set_position_mm(raw[X_AXIS], raw[Y_AXIS], raw[Z_AXIS], cart[E_CART]);
#endif
}
/**
* Setters for planner position (also setting stepper position).
*/
void Planner::set_position_mm(const AxisEnum axis, const float &v) {
#if ENABLED(DISTINCT_E_FACTORS)
const uint8_t axis_index = axis + (axis == E_AXIS ? active_extruder : 0);
last_extruder = active_extruder;
#else
const uint8_t axis_index = axis;
#endif
position[axis] = LROUND(axis_steps_per_mm[axis_index] * (v + (
#if ENABLED(AUTO_BED_LEVELING_UBL)
axis == Z_AXIS && leveling_active ? ubl.get_z_correction(current_position[X_AXIS], current_position[Y_AXIS]) :
#endif
0)
));
#if HAS_POSITION_FLOAT
position_float[axis] = v;
#endif
if (has_blocks_queued())
buffer_sync_block();
else
stepper.set_position(axis, position[axis]);
}
// Recalculate the steps/s^2 acceleration rates, based on the mm/s^2
void Planner::reset_acceleration_rates() {
#if ENABLED(DISTINCT_E_FACTORS)
#define AXIS_CONDITION (i < E_AXIS || i == E_AXIS + active_extruder)
#else
#define AXIS_CONDITION true
#endif
uint32_t highest_rate = 1;
LOOP_NUM_AXIS_N(i) {
max_acceleration_steps_per_s2[i] = max_acceleration_mm_per_s2[i] * axis_steps_per_mm[i];
if (AXIS_CONDITION) NOLESS(highest_rate, max_acceleration_steps_per_s2[i]);
}
cutoff_long = 4294967295UL / highest_rate; // 0xFFFFFFFFUL
#if ENABLED(JUNCTION_DEVIATION) && ENABLED(LIN_ADVANCE)
recalculate_max_e_jerk();
#endif
}
// Recalculate position, steps_to_mm if axis_steps_per_mm changes!
void Planner::refresh_positioning() {
LOOP_NUM_AXIS_N(i) steps_to_mm[i] = 1.0f / axis_steps_per_mm[i];
set_position_mm_kinematic(current_position);
reset_acceleration_rates();
}
#if ENABLED(AUTOTEMP)
void Planner::autotemp_M104_M109() {
if ((autotemp_enabled = parser.seen('F'))) autotemp_factor = parser.value_float();
if (parser.seen('S')) autotemp_min = parser.value_celsius();
if (parser.seen('B')) autotemp_max = parser.value_celsius();
}
#endif
Reference in New Issue View Git Blame Copy Permalink