mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 20:18:52 +00:00
f41c60d4a4
・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing
134 lines
3.1 KiB
C
134 lines
3.1 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* RIGIDBOARD Arduino Mega with RAMPS v1.4 pin assignments
|
|
*/
|
|
|
|
#define BOARD_NAME "RigidBoard"
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN 19 // Z-MAX pin J14 End Stops
|
|
#endif
|
|
|
|
#include "pins_RAMPS.h"
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
// RigidBot swaps E0 / E1 plugs vs RAMPS 1.3
|
|
#undef E0_STEP_PIN
|
|
#undef E0_DIR_PIN
|
|
#undef E0_ENABLE_PIN
|
|
#define E0_STEP_PIN 36
|
|
#define E0_DIR_PIN 34
|
|
#define E0_ENABLE_PIN 30
|
|
|
|
#undef E1_STEP_PIN
|
|
#undef E1_DIR_PIN
|
|
#undef E1_ENABLE_PIN
|
|
#define E1_STEP_PIN 26
|
|
#define E1_DIR_PIN 28
|
|
#define E1_ENABLE_PIN 24
|
|
|
|
#define STEPPER_RESET_PIN 41 // Stepper drivers have a reset on RigidBot
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#undef TEMP_0_PIN
|
|
#undef TEMP_1_PIN
|
|
#undef TEMP_BED_PIN
|
|
#define TEMP_0_PIN 14 // Analog Input
|
|
#define TEMP_1_PIN 13 // Analog Input
|
|
#define TEMP_BED_PIN 15 // Analog Input
|
|
|
|
// SPI for Max6675 or Max31855 Thermocouple
|
|
#undef MAX6675_SS
|
|
#if DISABLED(SDSUPPORT)
|
|
#define MAX6675_SS 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
|
|
#else
|
|
#define MAX6675_SS 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define RAMPS_D10_PIN 9 // EXTRUDER 1
|
|
#define MOSFET_D_PIN 12 // EXTRUDER 2 or FAN
|
|
|
|
#undef HEATER_BED_PIN
|
|
#define HEATER_BED_PIN 10
|
|
|
|
#undef FAN_PIN
|
|
#define FAN_PIN 8 // Same as RAMPS_13_EEF
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#undef PS_ON_PIN
|
|
#define PS_ON_PIN -1
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
// LCD Panel options for the RigidBoard
|
|
#if ENABLED(RIGIDBOT_PANEL)
|
|
|
|
#undef BEEPER_PIN
|
|
#define BEEPER_PIN -1
|
|
|
|
// Direction buttons
|
|
#define BTN_UP 37
|
|
#define BTN_DWN 35
|
|
#define BTN_LFT 33
|
|
#define BTN_RT 32
|
|
|
|
// 'R' button
|
|
#undef BTN_ENC
|
|
#define BTN_ENC 31
|
|
|
|
// Disable encoder
|
|
#undef BTN_EN1
|
|
#define BTN_EN1 -1
|
|
#undef BTN_EN2
|
|
#define BTN_EN2 -1
|
|
|
|
#undef SD_DETECT_PIN
|
|
#define SD_DETECT_PIN 22
|
|
|
|
#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
|
|
#undef BEEPER_PIN
|
|
#define BEEPER_PIN -1
|
|
|
|
#undef SD_DETECT_PIN
|
|
#define SD_DETECT_PIN 22
|
|
|
|
#undef KILL_PIN
|
|
#define KILL_PIN 32
|
|
|
|
#endif
|