mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-12-18 00:07:50 +00:00
198 lines
4.9 KiB
C
198 lines
4.9 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* Einsy-Rambo pin assignments
|
|
*/
|
|
|
|
#ifndef __AVR_ATmega2560__
|
|
#error "Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu."
|
|
#endif
|
|
|
|
#define BOARD_NAME "Einsy Rambo"
|
|
#define LARGE_FLASH true
|
|
|
|
//
|
|
// TMC2130 Configuration_adv defaults for EinsyRambo
|
|
//
|
|
#if DISABLED(HAVE_TMC2130)
|
|
#error "You must enable TMC2130 support in Configuration_adv.h for EinsyRambo."
|
|
#elif DISABLED(X_IS_TMC2130) || DISABLED(Y_IS_TMC2130) || DISABLED(Z_IS_TMC2130) || DISABLED(E0_IS_TMC2130)
|
|
#error "You must enable ([XYZ]|E0)_IS_TMC2130 in Configuration_adv.h for EinsyRambo."
|
|
#endif
|
|
|
|
// TMC2130 Diag Pins (currently just for reference)
|
|
#define X_DIAG_PIN 64
|
|
#define Y_DIAG_PIN 69
|
|
#define Z_DIAG_PIN 68
|
|
#define E0_DIAG_PIN 65
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.
|
|
// Otherwise use a physical endstop based configuration.
|
|
//
|
|
// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING.
|
|
//
|
|
|
|
#define X_MAX_PIN -1
|
|
#define Y_MAX_PIN -1
|
|
#define Z_MAX_PIN -1
|
|
|
|
#if DISABLED(SENSORLESS_HOMING)
|
|
|
|
#define X_MIN_PIN 12
|
|
#define Y_MIN_PIN 11
|
|
#define Z_MIN_PIN 10
|
|
|
|
#else
|
|
|
|
#define X_MIN_PIN X_DIAG_PIN
|
|
#define Y_MIN_PIN Y_DIAG_PIN
|
|
|
|
#if ENABLED(BLTOUCH)
|
|
#define Z_MIN_PIN 11 // Y-MIN
|
|
#define SERVO0_PIN 10 // Z-MIN
|
|
#else
|
|
#define Z_MIN_PIN 10
|
|
#endif
|
|
|
|
#endif
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN 10
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 37
|
|
#define X_DIR_PIN 49
|
|
#define X_ENABLE_PIN 29
|
|
#define X_CS_PIN 41
|
|
|
|
#define Y_STEP_PIN 36
|
|
#define Y_DIR_PIN 48
|
|
#define Y_ENABLE_PIN 28
|
|
#define Y_CS_PIN 39
|
|
|
|
#define Z_STEP_PIN 35
|
|
#define Z_DIR_PIN 47
|
|
#define Z_ENABLE_PIN 27
|
|
#define Z_CS_PIN 67
|
|
|
|
#define E0_STEP_PIN 34
|
|
#define E0_DIR_PIN 43
|
|
#define E0_ENABLE_PIN 26
|
|
#define E0_CS_PIN 66
|
|
|
|
#define E1_STEP_PIN -1
|
|
#define E1_DIR_PIN -1
|
|
#define E1_ENABLE_PIN -1
|
|
|
|
// Microstepping pins - uses SPI instead
|
|
#define X_MS1_PIN -1
|
|
#define X_MS2_PIN -1
|
|
#define Y_MS1_PIN -1
|
|
#define Y_MS2_PIN -1
|
|
#define Z_MS1_PIN -1
|
|
#define Z_MS2_PIN -1
|
|
#define E0_MS1_PIN -1
|
|
#define E0_MS2_PIN -1
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 0 // Analog Input
|
|
#define TEMP_1_PIN 1 // Analog Input
|
|
#define TEMP_BED_PIN 2 // Analog Input
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 3
|
|
#define HEATER_1_PIN -1
|
|
#define HEATER_2_PIN -1
|
|
#define HEATER_BED_PIN 4
|
|
|
|
#define FAN_PIN 8
|
|
#define FAN1_PIN 6
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SDSS 77
|
|
#define LED_PIN 13
|
|
#define CASE_LIGHT_PIN 9
|
|
|
|
//
|
|
// M3/M4/M5 - Spindle/Laser Control
|
|
//
|
|
// use P1 connector for spindle pins
|
|
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
|
|
#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!
|
|
#define SPINDLE_DIR_PIN 19
|
|
|
|
//
|
|
// Průša i3 MK2 Multiplexer Support
|
|
//
|
|
#define E_MUX0_PIN 17
|
|
#define E_MUX1_PIN 16
|
|
#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if ENABLED(ULTRA_LCD)
|
|
|
|
#define KILL_PIN 32
|
|
|
|
#if ENABLED(NEWPANEL)
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define LCD_PINS_RS 85
|
|
#define LCD_PINS_ENABLE 71
|
|
#define LCD_PINS_D4 70
|
|
#define BTN_EN1 61
|
|
#define BTN_EN2 59
|
|
#else
|
|
#define LCD_PINS_RS 82
|
|
#define LCD_PINS_ENABLE 61
|
|
#define LCD_PINS_D4 59
|
|
#define LCD_PINS_D5 70
|
|
#define LCD_PINS_D6 85
|
|
#define LCD_PINS_D7 71
|
|
#define BTN_EN1 14
|
|
#define BTN_EN2 72
|
|
#endif
|
|
|
|
#define BTN_ENC 9 // AUX-2
|
|
#define BEEPER_PIN 84 // AUX-4
|
|
#define SD_DETECT_PIN 15
|
|
|
|
#endif // NEWPANEL
|
|
#endif // ULTRA_LCD
|