1
0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-11-23 12:04:19 +00:00
MarlinFirmware/Marlin/pins_MKS_13.h
Alexey Shvetsov f38b8c5bf8 MKS 1.3+: Add pin mapping for PS_ON
This allows the use of D4 as PS_ON since MKS Gen doesn't have a PS_ON pin. However this effectively allows only 3 servos (instead of 4).

Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
2017-07-21 18:50:05 -05:00

145 lines
3.6 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Arduino Mega with RAMPS v1.4 adjusted pin assignments
*
* MKS v1.3 (Extruder, Fan, Bed)
* MKS v1.3 (Extruder, Extruder, Fan, Bed)
* MKS v1.4 (Extruder, Fan, Bed)
* MKS v1.4 (Extruder, Extruder, Fan, Bed)
*/
#if HOTENDS > 2 || E_STEPPERS > 2
#error "MKS 1.3/1.4 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_NAME "MKS > v1.3"
//
// Heaters / Fans
//
// Power outputs EFBF or EFBE
#define MOSFET_D_PIN 7
//
// PSU / SERVO
//
// If POWER_SUPPLY is specified, always hijack Servo 3
//
#if POWER_SUPPLY > 0
#define SERVO3_PIN -1
#define PS_ON_PIN 4
#endif
#include "pins_RAMPS.h"
//
// LCD / Controller
//
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
/**
* VIKI2 Has two groups of wires with...
*
* +Vin + Input supply, requires 120ma for LCD and mSD card
* GND Ground Pin
* MOSI Data input for LCD and SD
* MISO Data output for SD
* SCK Clock for LCD and SD
* AO Reg. Sel for LCD
* LCS Chip Select for LCD
* SDCS Chip Select for SD
* SDCD Card Detect pin for SD
* ENCA Encoder output A
* ENCB Encoder output B
* ENCBTN Encoder button switch
*
* BTN Panel mounted button switch
* BUZZER Piezo buzzer
* BLUE-LED Blue LED ring pin (3 to 5v, mosfet buffered)
* RED-LED Red LED ring pin (3 to 5v, mosfet buffered)
*
* This configuration uses the following arrangement:
*
* EXP1 D37 = EN2 D35 = EN1 EXP2 D50 = MISO D52 = SCK
* D17 = BLUE D16 = RED D31 = ENC D53 = SDCS
* D23 = KILL D25 = BUZZ D33 = --- D51 = MOSI
* D27 = A0 D29 = LCS D49 = SDCD RST = ---
* GND = GND 5V = 5V GND = --- D41 = ---
*/
#undef BTN_EN1
#undef BTN_EN2
#undef BTN_ENC
#undef DOGLCD_A0
#undef DOGLCD_CS
#undef SD_DETECT_PIN
#undef BEEPER_PIN
#undef KILL_PIN
//
// VIKI2 12-wire lead
//
// orange/white SDCD
#define SD_DETECT_PIN 49
// white ENCA
#define BTN_EN1 35
// green ENCB
#define BTN_EN2 37
// purple ENCBTN
#define BTN_ENC 31
// brown A0
#define DOGLCD_A0 27
// green/white LCS
#define DOGLCD_CS 29
// 50 gray MISO
// 51 yellow MOSI
// 52 orange SCK
// blue SDCS
//#define SDSS 53
//
// VIKI2 4-wire lead
//
// blue BTN
#define KILL_PIN 23
// green BUZZER
#define BEEPER_PIN 25
// yellow RED-LED
#define STAT_LED_RED_PIN 16
// white BLUE-LED
#define STAT_LED_BLUE_PIN 17
#endif