3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-11-23 20:18:52 +00:00
Code Issues Releases Wiki Activity
9af67e2446
MarlinFirmware/Marlin/pins_SANGUINOLOLU_11.h
essgcee 61be28133d Support for Creality CR-10 
Creality board is a Melzi / Sanguinololu variant, but using different pins for LCD control (and maybe other minor variations)
2017-07-06 23:08:10 -05:00

300 lines
8.4 KiB
C
Raw Blame History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Sanguinololu board pin assignments
*/
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "Sanguinololu <1.2"
#endif
#define IS_MELZI (MB(MELZI) || MB(MELZI_MAKR3D) || MB(MELZI_CREALITY))
//
// Limit Switches
//
#define X_STOP_PIN 18
#define Y_STOP_PIN 19
#define Z_STOP_PIN 20
//
// Steppers
//
#define X_STEP_PIN 15
#define X_DIR_PIN 21
#define Y_STEP_PIN 22
#define Y_DIR_PIN 23
#define Z_STEP_PIN 3
#define Z_DIR_PIN 2
#define E0_STEP_PIN 1
#define E0_DIR_PIN 0
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)
//
// Heaters / Fans
//
#define HEATER_0_PIN 13 // (extruder)
#if ENABLED(SANGUINOLOLU_V_1_2)
#define HEATER_BED_PIN 12 // (bed)
#define X_ENABLE_PIN 14
#define Y_ENABLE_PIN 14
#define Z_ENABLE_PIN 26
#define E0_ENABLE_PIN 14
#if ENABLED(LCD_I2C_PANELOLU2)
#define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
#endif
#else
#define HEATER_BED_PIN 14 // (bed)
#define X_ENABLE_PIN -1
#define Y_ENABLE_PIN -1
#define Z_ENABLE_PIN -1
#define E0_ENABLE_PIN -1
#endif
#if MB(AZTEEG_X1) || MB(STB_11) || IS_MELZI
#define FAN_PIN 4 // Works for Panelolu2 too
#endif
//
// Misc. Functions
//
/**
* In some versions of the Sanguino libraries the pin
* definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi).
* If you encounter issues with these pins, upgrade your
* Sanguino libraries! See #368.
*/
//#define SDSS 24
#define SDSS 31
#if IS_MELZI
#define LED_PIN 27
#elif MB(STB_11)
#define LCD_BACKLIGHT_PIN 17 // LCD backlight LED
#endif
#if DISABLED(SPINDLE_LASER_ENABLE) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
#define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM - see if IO Header is available
#endif
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#if ENABLED(DOGLCD)
#if ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
#if IS_MELZI // Melzi board
#define LCD_PINS_RS 30 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 29 // SID (MOSI)
#define LCD_PINS_D4 17 // SCK (CLK) clock
// Pin 27 is taken by LED_PIN, but Melzi LED does nothing with
// Marlin so this can be used for BEEPER_PIN. You can use this pin
// with M42 instead of BEEPER_PIN.
#define BEEPER_PIN 27
#else // Sanguinololu 1.3
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif
#else // DOGM SPI LCD Support
#define DOGLCD_A0 30
#define LCD_CONTRAST 1
#if ENABLED(MAKRPANEL)
#define BEEPER_PIN 29
#define DOGLCD_CS 17
#define LCD_BACKLIGHT_PIN 28 // PA3
#else // !MAKRPANEL
#define DOGLCD_CS 29
#endif
#endif
// Uncomment screen orientation
#define LCD_SCREEN_ROT_0
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#else // !DOGLCD
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif // !DOGLCD
#define BTN_EN1 11
#define BTN_EN2 10
#if ENABLED(LCD_I2C_PANELOLU2)
#if IS_MELZI
#define BTN_ENC 29
#define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi
#else
#define BTN_ENC 30
#endif
#elif ENABLED(LCD_FOR_MELZI)
#define LCD_PINS_RS 17
#define LCD_PINS_ENABLE 16
#define LCD_PINS_D4 11
#define BTN_ENC 28
#define BTN_EN1 29
#define BTN_EN2 30
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_0_NOP
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_2 DELAY_3_NOP
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_0_NOP
#endif
#else // !LCD_I2C_PANELOLU2 && !LCD_FOR_MELZI
#define BTN_ENC 16
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
#endif
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE)
#if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 11
#elif !MB(MELZI) // use X stepper motor socket
/**
* To control the spindle speed and have an LCD you must sacrifice
* the Extruder and pull some signals off the X stepper driver socket.
*
* The following assumes:
* - The X stepper driver socket is empty
* - The extruder driver socket has a driver board plugged into it
* - The X stepper wires are attached the the extruder connector
*/
/**
* Where to get the spindle signals
*
* spindle signal socket name socket name
* -------
* /ENABLE O| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
* SPINDLE_LASER_ENABLE_PIN DIR O| |O GND
* -------
*
* Note: Socket names vary from vendor to vendor.
*/
#undef X_DIR_PIN
#undef X_ENABLE_PIN
#undef X_STEP_PIN
#define X_DIR_PIN 0
#define X_ENABLE_PIN 14
#define X_STEP_PIN 1
#define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 21 // Pin should have a pullup!
#define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin
#endif
#endif // SPINDLE_LASER_ENABLE
Reference in New Issue View Git Blame Copy Permalink