3DPrinting/MarlinFirmware
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Marlin.git synced 2024-11-24 04:29:34 +00:00
Code Issues Releases Wiki Activity
bb4529f7d2
MarlinFirmware/Marlin/ultralcd.cpp
Scott Lahteine bb4529f7d2 PLA / ABS => Material 1 / 2
2016-11-28 01:37:24 -06:00

3027 lines
100 KiB
C++
Executable File
Raw Blame History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#include "ultralcd.h"
#if ENABLED(ULTRA_LCD)
#include "Marlin.h"
#include "language.h"
#include "cardreader.h"
#include "temperature.h"
#include "stepper.h"
#include "configuration_store.h"
#include "utility.h"
#if HAS_BUZZER && DISABLED(LCD_USE_I2C_BUZZER)
#include "buzzer.h"
#endif
#if ENABLED(BLTOUCH)
#include "endstops.h"
#endif
#if ENABLED(PRINTCOUNTER)
#include "printcounter.h"
#include "duration_t.h"
#endif
int lcd_preheat_hotend_temp[2], lcd_preheat_bed_temp[2], lcd_preheat_fan_speed[2];
#if ENABLED(FILAMENT_LCD_DISPLAY)
millis_t previous_lcd_status_ms = 0;
#endif
uint8_t lcd_status_message_level;
char lcd_status_message[3 * (LCD_WIDTH) + 1] = WELCOME_MSG; // worst case is kana with up to 3*LCD_WIDTH+1
#if ENABLED(DOGLCD)
#include "ultralcd_impl_DOGM.h"
#else
#include "ultralcd_impl_HD44780.h"
#endif
// The main status screen
void lcd_status_screen();
millis_t next_lcd_update_ms;
uint8_t lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW; // Set when the LCD needs to draw, decrements after every draw. Set to 2 in LCD routines so the LCD gets at least 1 full redraw (first redraw is partial)
#if ENABLED(DAC_STEPPER_CURRENT)
#include "stepper_dac.h" //was dac_mcp4728.h MarlinMain uses stepper dac for the m-codes
uint16_t driverPercent[XYZE];
#endif
#if ENABLED(ULTIPANEL)
// place-holders for Ki and Kd edits
float raw_Ki, raw_Kd;
/**
* REVERSE_MENU_DIRECTION
*
* To reverse the menu direction we need a general way to reverse
* the direction of the encoder everywhere. So encoderDirection is
* added to allow the encoder to go the other way.
*
* This behavior is limited to scrolling Menus and SD card listings,
* and is disabled in other contexts.
*/
#if ENABLED(REVERSE_MENU_DIRECTION)
int8_t encoderDirection = 1;
#define ENCODER_DIRECTION_NORMAL() (encoderDirection = 1)
#define ENCODER_DIRECTION_MENUS() (encoderDirection = -1)
#else
#define ENCODER_DIRECTION_NORMAL() ;
#define ENCODER_DIRECTION_MENUS() ;
#endif
int8_t encoderDiff; // updated from interrupt context and added to encoderPosition every LCD update
millis_t manual_move_start_time = 0;
int8_t manual_move_axis = (int8_t)NO_AXIS;
#if EXTRUDERS > 1
int8_t manual_move_e_index = 0;
#else
#define manual_move_e_index 0
#endif
bool encoderRateMultiplierEnabled;
int32_t lastEncoderMovementMillis;
#if HAS_POWER_SWITCH
extern bool powersupply;
#endif
#if HAS_CASE_LIGHT
extern bool case_light_on;
#endif
const float manual_feedrate_mm_m[] = MANUAL_FEEDRATE;
void lcd_main_menu();
void lcd_tune_menu();
void lcd_prepare_menu();
void lcd_move_menu();
void lcd_control_menu();
void lcd_control_temperature_menu();
void lcd_control_temperature_preheat_material1_settings_menu();
void lcd_control_temperature_preheat_material2_settings_menu();
void lcd_control_motion_menu();
void lcd_control_volumetric_menu();
#if ENABLED(DAC_STEPPER_CURRENT)
void dac_driver_commit();
void dac_driver_getValues();
void lcd_dac_menu();
void lcd_dac_write_eeprom();
#endif
#if ENABLED(LCD_INFO_MENU)
#if ENABLED(PRINTCOUNTER)
void lcd_info_stats_menu();
#endif
void lcd_info_thermistors_menu();
void lcd_info_board_menu();
void lcd_info_menu();
#endif // LCD_INFO_MENU
#if ENABLED(FILAMENT_CHANGE_FEATURE)
void lcd_filament_change_option_menu();
void lcd_filament_change_init_message();
void lcd_filament_change_unload_message();
void lcd_filament_change_insert_message();
void lcd_filament_change_load_message();
void lcd_filament_change_extrude_message();
void lcd_filament_change_resume_message();
#endif
#if HAS_LCD_CONTRAST
void lcd_set_contrast();
#endif
#if ENABLED(FWRETRACT)
void lcd_control_retract_menu();
#endif
#if ENABLED(DELTA_CALIBRATION_MENU)
void lcd_delta_calibrate_menu();
#endif
#if ENABLED(MANUAL_BED_LEVELING)
#include "mesh_bed_leveling.h"
#endif
// Function pointer to menu functions.
typedef void (*screenFunc_t)();
// Different types of actions that can be used in menu items.
#define menu_action_back(dummy) _menu_action_back()
void _menu_action_back();
void menu_action_submenu(screenFunc_t data);
void menu_action_gcode(const char* pgcode);
void menu_action_function(screenFunc_t data);
void menu_action_setting_edit_bool(const char* pstr, bool* ptr);
void menu_action_setting_edit_int3(const char* pstr, int* ptr, int minValue, int maxValue);
void menu_action_setting_edit_float3(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float32(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float43(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float5(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float51(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float52(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_float62(const char* pstr, float* ptr, float minValue, float maxValue);
void menu_action_setting_edit_long5(const char* pstr, unsigned long* ptr, unsigned long minValue, unsigned long maxValue);
void menu_action_setting_edit_callback_bool(const char* pstr, bool* ptr, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_int3(const char* pstr, int* ptr, int minValue, int maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float3(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float32(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float43(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float5(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float51(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float52(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_float62(const char* pstr, float* ptr, float minValue, float maxValue, screenFunc_t callbackFunc);
void menu_action_setting_edit_callback_long5(const char* pstr, unsigned long* ptr, unsigned long minValue, unsigned long maxValue, screenFunc_t callbackFunc);
#if ENABLED(SDSUPPORT)
void lcd_sdcard_menu();
void menu_action_sdfile(const char* filename, char* longFilename);
void menu_action_sddirectory(const char* filename, char* longFilename);
#endif
/* Helper macros for menus */
#ifndef ENCODER_FEEDRATE_DEADZONE
#define ENCODER_FEEDRATE_DEADZONE 10
#endif
#ifndef ENCODER_STEPS_PER_MENU_ITEM
#define ENCODER_STEPS_PER_MENU_ITEM 5
#endif
#ifndef ENCODER_PULSES_PER_STEP
#define ENCODER_PULSES_PER_STEP 1
#endif
/**
* START_SCREEN_OR_MENU generates init code for a screen or menu
*
* encoderLine is the position based on the encoder
* encoderTopLine is the top menu line to display
* _lcdLineNr is the index of the LCD line (e.g., 0-3)
* _menuLineNr is the menu item to draw and process
* _thisItemNr is the index of each MENU_ITEM or STATIC_ITEM
* _countedItems is the total number of items in the menu (after one call)
*/
#define START_SCREEN_OR_MENU(LIMIT) \
ENCODER_DIRECTION_MENUS(); \
encoderRateMultiplierEnabled = false; \
if (encoderPosition > 0x8000) encoderPosition = 0; \
static int8_t _countedItems = 0; \
int8_t encoderLine = encoderPosition / ENCODER_STEPS_PER_MENU_ITEM; \
if (_countedItems > 0 && encoderLine >= _countedItems - LIMIT) { \
encoderLine = max(0, _countedItems - LIMIT); \
encoderPosition = encoderLine * (ENCODER_STEPS_PER_MENU_ITEM); \
}
#define SCREEN_OR_MENU_LOOP() \
int8_t _menuLineNr = encoderTopLine, _thisItemNr; \
for (int8_t _lcdLineNr = 0; _lcdLineNr < LCD_HEIGHT; _lcdLineNr++, _menuLineNr++) { \
_thisItemNr = 0
/**
* START_SCREEN Opening code for a screen having only static items.
* Do simplified scrolling of the entire screen.
*
* START_MENU Opening code for a screen with menu items.
* Scroll as-needed to keep the selected line in view.
*/
#define START_SCREEN() \
START_SCREEN_OR_MENU(LCD_HEIGHT); \
encoderTopLine = encoderLine; \
bool _skipStatic = false; \
SCREEN_OR_MENU_LOOP()
#define START_MENU() \
START_SCREEN_OR_MENU(1); \
NOMORE(encoderTopLine, encoderLine); \
if (encoderLine >= encoderTopLine + LCD_HEIGHT) { \
encoderTopLine = encoderLine - (LCD_HEIGHT - 1); \
} \
bool _skipStatic = true; \
SCREEN_OR_MENU_LOOP()
/**
* MENU_ITEM generates draw & handler code for a menu item, potentially calling:
*
* lcd_implementation_drawmenu_[type](sel, row, label, arg3...)
* menu_action_[type](arg3...)
*
* Examples:
* MENU_ITEM(back, MSG_WATCH, 0 [dummy parameter] )
* or
* MENU_BACK(MSG_WATCH)
* lcd_implementation_drawmenu_back(sel, row, PSTR(MSG_WATCH))
* menu_action_back()
*
* MENU_ITEM(function, MSG_PAUSE_PRINT, lcd_sdcard_pause)
* lcd_implementation_drawmenu_function(sel, row, PSTR(MSG_PAUSE_PRINT), lcd_sdcard_pause)
* menu_action_function(lcd_sdcard_pause)
*
* MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_percentage, 10, 999)
* MENU_ITEM(setting_edit_int3, MSG_SPEED, PSTR(MSG_SPEED), &feedrate_percentage, 10, 999)
* lcd_implementation_drawmenu_setting_edit_int3(sel, row, PSTR(MSG_SPEED), PSTR(MSG_SPEED), &feedrate_percentage, 10, 999)
* menu_action_setting_edit_int3(PSTR(MSG_SPEED), &feedrate_percentage, 10, 999)
*
*/
#define _MENU_ITEM_PART_1(TYPE, LABEL, ...) \
if (_menuLineNr == _thisItemNr) { \
if (lcdDrawUpdate) \
lcd_implementation_drawmenu_ ## TYPE(encoderLine == _thisItemNr, _lcdLineNr, PSTR(LABEL), ## __VA_ARGS__); \
if (lcd_clicked && encoderLine == _thisItemNr) {
#define _MENU_ITEM_PART_2(TYPE, ...) \
menu_action_ ## TYPE(__VA_ARGS__); \
return; \
} \
} \
++_thisItemNr
#define MENU_ITEM(TYPE, LABEL, ...) do { \
_skipStatic = false; \
_MENU_ITEM_PART_1(TYPE, LABEL, ## __VA_ARGS__); \
_MENU_ITEM_PART_2(TYPE, ## __VA_ARGS__); \
} while(0)
#define MENU_BACK(LABEL) MENU_ITEM(back, LABEL, 0)
// Used to print static text with no visible cursor.
#define STATIC_ITEM(LABEL, ...) \
if (_menuLineNr == _thisItemNr) { \
if (_skipStatic && encoderLine <= _thisItemNr) { \
encoderPosition += ENCODER_STEPS_PER_MENU_ITEM; \
lcdDrawUpdate = LCDVIEW_CALL_REDRAW_NEXT; \
} \
if (lcdDrawUpdate) \
lcd_implementation_drawmenu_static(_lcdLineNr, PSTR(LABEL), ## __VA_ARGS__); \
} \
++_thisItemNr
#define END_SCREEN() \
} \
_countedItems = _thisItemNr
#define END_MENU() \
} \
_countedItems = _thisItemNr; \
UNUSED(_skipStatic)
#if ENABLED(ENCODER_RATE_MULTIPLIER)
//#define ENCODER_RATE_MULTIPLIER_DEBUG // If defined, output the encoder steps per second value
/**
* MENU_MULTIPLIER_ITEM generates drawing and handling code for a multiplier menu item
*/
#define MENU_MULTIPLIER_ITEM(type, label, ...) do { \
_MENU_ITEM_PART_1(type, label, ## __VA_ARGS__); \
encoderRateMultiplierEnabled = true; \
lastEncoderMovementMillis = 0; \
_MENU_ITEM_PART_2(type, ## __VA_ARGS__); \
} while(0)
#endif //ENCODER_RATE_MULTIPLIER
#define MENU_ITEM_DUMMY() do { _thisItemNr++; } while(0)
#define MENU_ITEM_EDIT(type, label, ...) MENU_ITEM(setting_edit_ ## type, label, PSTR(label), ## __VA_ARGS__)
#define MENU_ITEM_EDIT_CALLBACK(type, label, ...) MENU_ITEM(setting_edit_callback_ ## type, label, PSTR(label), ## __VA_ARGS__)
#if ENABLED(ENCODER_RATE_MULTIPLIER)
#define MENU_MULTIPLIER_ITEM_EDIT(type, label, ...) MENU_MULTIPLIER_ITEM(setting_edit_ ## type, label, PSTR(label), ## __VA_ARGS__)
#define MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(type, label, ...) MENU_MULTIPLIER_ITEM(setting_edit_callback_ ## type, label, PSTR(label), ## __VA_ARGS__)
#else //!ENCODER_RATE_MULTIPLIER
#define MENU_MULTIPLIER_ITEM_EDIT(type, label, ...) MENU_ITEM(setting_edit_ ## type, label, PSTR(label), ## __VA_ARGS__)
#define MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(type, label, ...) MENU_ITEM(setting_edit_callback_ ## type, label, PSTR(label), ## __VA_ARGS__)
#endif //!ENCODER_RATE_MULTIPLIER
/** Used variables to keep track of the menu */
volatile uint8_t buttons; //the last checked buttons in a bit array.
#if ENABLED(REPRAPWORLD_KEYPAD)
volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values
#endif
#if ENABLED(LCD_HAS_SLOW_BUTTONS)
volatile uint8_t slow_buttons; // Bits of the pressed buttons.
#endif
int8_t encoderTopLine; /* scroll offset in the current menu */
millis_t next_button_update_ms;
uint8_t lastEncoderBits;
uint32_t encoderPosition;
#if PIN_EXISTS(SD_DETECT)
uint8_t lcd_sd_status;
#endif
typedef struct {
screenFunc_t menu_function;
uint32_t encoder_position;
} menuPosition;
screenFunc_t currentScreen = lcd_status_screen; // pointer to the currently active menu handler
menuPosition screen_history[10];
uint8_t screen_history_depth = 0;
// LCD and menu clicks
bool lcd_clicked, wait_for_unclick, defer_return_to_status;
// Variables used when editing values.
const char* editLabel;
void* editValue;
int32_t minEditValue, maxEditValue;
screenFunc_t callbackFunc; // call this after editing
/**
* General function to go directly to a screen
*/
void lcd_goto_screen(screenFunc_t screen, const uint32_t encoder = 0) {
if (currentScreen != screen) {
currentScreen = screen;
encoderPosition = encoder;
if (screen == lcd_status_screen) {
defer_return_to_status = false;
screen_history_depth = 0;
}
lcd_implementation_clear();
#if ENABLED(LCD_PROGRESS_BAR)
// For LCD_PROGRESS_BAR re-initialize custom characters
lcd_set_custom_characters(screen == lcd_status_screen);
#endif
lcdDrawUpdate = LCDVIEW_CALL_REDRAW_NEXT;
}
}
void lcd_return_to_status() { lcd_goto_screen(lcd_status_screen); }
inline void lcd_save_previous_menu() {
if (screen_history_depth < COUNT(screen_history)) {
screen_history[screen_history_depth].menu_function = currentScreen;
screen_history[screen_history_depth].encoder_position = encoderPosition;
++screen_history_depth;
}
}
void lcd_goto_previous_menu() {
if (screen_history_depth > 0) {
--screen_history_depth;
lcd_goto_screen(
screen_history[screen_history_depth].menu_function,
screen_history[screen_history_depth].encoder_position
);
}
else
lcd_return_to_status();
}
#endif // ULTIPANEL
/**
*
* "Info Screen"
*
* This is very display-dependent, so the lcd implementation draws this.
*/
void lcd_status_screen() {
#if ENABLED(ULTIPANEL)
ENCODER_DIRECTION_NORMAL();
encoderRateMultiplierEnabled = false;
#endif
#if ENABLED(LCD_PROGRESS_BAR)
millis_t ms = millis();
#if DISABLED(PROGRESS_MSG_ONCE)
if (ELAPSED(ms, progress_bar_ms + PROGRESS_BAR_MSG_TIME + PROGRESS_BAR_BAR_TIME)) {
progress_bar_ms = ms;
}
#endif
#if PROGRESS_MSG_EXPIRE > 0
// Handle message expire
if (expire_status_ms > 0) {
#if ENABLED(SDSUPPORT)
if (card.isFileOpen()) {
// Expire the message when printing is active
if (IS_SD_PRINTING) {
if (ELAPSED(ms, expire_status_ms)) {
lcd_status_message[0] = '\0';
expire_status_ms = 0;
}
}
else {
expire_status_ms += LCD_UPDATE_INTERVAL;
}
}
else {
expire_status_ms = 0;
}
#else
expire_status_ms = 0;
#endif //SDSUPPORT
}
#endif
#endif //LCD_PROGRESS_BAR
lcd_implementation_status_screen();
#if ENABLED(ULTIPANEL)
if (lcd_clicked) {
#if ENABLED(FILAMENT_LCD_DISPLAY)
previous_lcd_status_ms = millis(); // get status message to show up for a while
#endif
lcd_implementation_init( // to maybe revive the LCD if static electricity killed it.
#if ENABLED(LCD_PROGRESS_BAR)
false
#endif
);
lcd_goto_screen(lcd_main_menu);
}
#if ENABLED(ULTIPANEL_FEEDMULTIPLY)
int new_frm = feedrate_percentage + (int32_t)encoderPosition;
// Dead zone at 100% feedrate
if ((feedrate_percentage < 100 && new_frm > 100) || (feedrate_percentage > 100 && new_frm < 100)) {
feedrate_percentage = 100;
encoderPosition = 0;
}
else if (feedrate_percentage == 100) {
if ((int32_t)encoderPosition > ENCODER_FEEDRATE_DEADZONE) {
feedrate_percentage += (int32_t)encoderPosition - (ENCODER_FEEDRATE_DEADZONE);
encoderPosition = 0;
}
else if ((int32_t)encoderPosition < -(ENCODER_FEEDRATE_DEADZONE)) {
feedrate_percentage += (int32_t)encoderPosition + ENCODER_FEEDRATE_DEADZONE;
encoderPosition = 0;
}
}
else {
feedrate_percentage = new_frm;
encoderPosition = 0;
}
#endif // ULTIPANEL_FEEDMULTIPLY
feedrate_percentage = constrain(feedrate_percentage, 10, 999);
#endif //ULTIPANEL
}
/**
*
* draw the kill screen
*
*/
void kill_screen(const char* lcd_msg) {
lcd_init();
lcd_setalertstatuspgm(lcd_msg);
#if ENABLED(DOGLCD)
u8g.firstPage();
do {
lcd_kill_screen();
} while (u8g.nextPage());
#else
lcd_kill_screen();
#endif
}
#if ENABLED(ULTIPANEL)
inline void line_to_current(AxisEnum axis) {
planner.buffer_line_kinematic(current_position, MMM_TO_MMS(manual_feedrate_mm_m[axis]), active_extruder);
}
#if ENABLED(SDSUPPORT)
void lcd_sdcard_pause() {
card.pauseSDPrint();
print_job_timer.pause();
}
void lcd_sdcard_resume() {
card.startFileprint();
print_job_timer.start();
}
void lcd_sdcard_stop() {
card.stopSDPrint();
clear_command_queue();
quickstop_stepper();
print_job_timer.stop();
#if ENABLED(AUTOTEMP)
thermalManager.autotempShutdown();
#endif
wait_for_heatup = false;
lcd_setstatus(MSG_PRINT_ABORTED, true);
}
#endif //SDSUPPORT
/**
*
* "Main" menu
*
*/
void lcd_main_menu() {
START_MENU();
MENU_BACK(MSG_WATCH);
//
// Switch case light on/off
//
#if HAS_CASE_LIGHT && ENABLED(MENU_ITEM_CASE_LIGHT)
if (case_light_on == 0)
MENU_ITEM(gcode, MSG_LIGHTS_ON, PSTR("M355 S1"));
else
MENU_ITEM(gcode, MSG_LIGHTS_OFF, PSTR("M355 S0"));
#endif
#if ENABLED(BLTOUCH)
if (!endstops.z_probe_enabled && TEST_BLTOUCH())
MENU_ITEM(gcode, MSG_BLTOUCH_RESET, PSTR("M280 P" STRINGIFY(Z_ENDSTOP_SERVO_NR) " S" STRINGIFY(BLTOUCH_RESET)));
#endif
if (planner.movesplanned() || IS_SD_PRINTING) {
MENU_ITEM(submenu, MSG_TUNE, lcd_tune_menu);
}
else {
MENU_ITEM(submenu, MSG_PREPARE, lcd_prepare_menu);
#if ENABLED(DELTA_CALIBRATION_MENU)
MENU_ITEM(submenu, MSG_DELTA_CALIBRATE, lcd_delta_calibrate_menu);
#endif
}
MENU_ITEM(submenu, MSG_CONTROL, lcd_control_menu);
#if ENABLED(SDSUPPORT)
if (card.cardOK) {
if (card.isFileOpen()) {
if (card.sdprinting)
MENU_ITEM(function, MSG_PAUSE_PRINT, lcd_sdcard_pause);
else
MENU_ITEM(function, MSG_RESUME_PRINT, lcd_sdcard_resume);
MENU_ITEM(function, MSG_STOP_PRINT, lcd_sdcard_stop);
}
else {
MENU_ITEM(submenu, MSG_CARD_MENU, lcd_sdcard_menu);
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(gcode, MSG_CNG_SDCARD, PSTR("M21")); // SD-card changed by user
#endif
}
}
else {
MENU_ITEM(submenu, MSG_NO_CARD, lcd_sdcard_menu);
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(gcode, MSG_INIT_SDCARD, PSTR("M21")); // Manually initialize the SD-card via user interface
#endif
}
#endif //SDSUPPORT
#if ENABLED(LCD_INFO_MENU)
MENU_ITEM(submenu, MSG_INFO_MENU, lcd_info_menu);
#endif
END_MENU();
}
/**
*
* "Tune" submenu items
*
*/
/**
* Set the home offset based on the current_position
*/
void lcd_set_home_offsets() {
// M428 Command
enqueue_and_echo_commands_P(PSTR("M428"));
lcd_return_to_status();
}
#if ENABLED(BABYSTEPPING)
long babysteps_done = 0;
void _lcd_babystep(const AxisEnum axis, const char* msg) {
if (lcd_clicked) { defer_return_to_status = false; return lcd_goto_previous_menu(); }
ENCODER_DIRECTION_NORMAL();
if (encoderPosition) {
int babystep_increment = (int32_t)encoderPosition * (BABYSTEP_MULTIPLICATOR);
encoderPosition = 0;
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
thermalManager.babystep_axis(axis, babystep_increment);
babysteps_done += babystep_increment;
}
if (lcdDrawUpdate)
lcd_implementation_drawedit(msg, ftostr43sign(
((1000 * babysteps_done) * planner.steps_to_mm[axis]) * 0.001f
));
}
#if ENABLED(BABYSTEP_XY)
void _lcd_babystep_x() { _lcd_babystep(X_AXIS, PSTR(MSG_BABYSTEPPING_X)); }
void _lcd_babystep_y() { _lcd_babystep(Y_AXIS, PSTR(MSG_BABYSTEPPING_Y)); }
void lcd_babystep_x() { lcd_goto_screen(_lcd_babystep_x); babysteps_done = 0; defer_return_to_status = true; }
void lcd_babystep_y() { lcd_goto_screen(_lcd_babystep_y); babysteps_done = 0; defer_return_to_status = true; }
#endif
void _lcd_babystep_z() { _lcd_babystep(Z_AXIS, PSTR(MSG_BABYSTEPPING_Z)); }
void lcd_babystep_z() { lcd_goto_screen(_lcd_babystep_z); babysteps_done = 0; defer_return_to_status = true; }
#endif //BABYSTEPPING
/**
* Watch temperature callbacks
*/
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0
#if TEMP_SENSOR_0 != 0
void watch_temp_callback_E0() { thermalManager.start_watching_heater(0); }
#endif
#if HOTENDS > 1 && TEMP_SENSOR_1 != 0
void watch_temp_callback_E1() { thermalManager.start_watching_heater(1); }
#endif // HOTENDS > 1
#if HOTENDS > 2 && TEMP_SENSOR_2 != 0
void watch_temp_callback_E2() { thermalManager.start_watching_heater(2); }
#endif // HOTENDS > 2
#if HOTENDS > 3 && TEMP_SENSOR_3 != 0
void watch_temp_callback_E3() { thermalManager.start_watching_heater(3); }
#endif // HOTENDS > 3
#else
#if TEMP_SENSOR_0 != 0
void watch_temp_callback_E0() {}
#endif
#if HOTENDS > 1 && TEMP_SENSOR_1 != 0
void watch_temp_callback_E1() {}
#endif // HOTENDS > 1
#if HOTENDS > 2 && TEMP_SENSOR_2 != 0
void watch_temp_callback_E2() {}
#endif // HOTENDS > 2
#if HOTENDS > 3 && TEMP_SENSOR_3 != 0
void watch_temp_callback_E3() {}
#endif // HOTENDS > 3
#endif
#if ENABLED(THERMAL_PROTECTION_BED) && WATCH_BED_TEMP_PERIOD > 0
#if TEMP_SENSOR_BED != 0
void watch_temp_callback_bed() { thermalManager.start_watching_bed(); }
#endif
#else
#if TEMP_SENSOR_BED != 0
void watch_temp_callback_bed() {}
#endif
#endif
#if ENABLED(FILAMENT_CHANGE_FEATURE)
void lcd_enqueue_filament_change() {
lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_INIT);
enqueue_and_echo_commands_P(PSTR("M600"));
}
#endif
/**
*
* "Tune" submenu
*
*/
void lcd_tune_menu() {
START_MENU();
//
// ^ Main
//
MENU_BACK(MSG_MAIN);
//
// Speed:
//
MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_percentage, 10, 999);
// Manual bed leveling, Bed Z:
#if ENABLED(MANUAL_BED_LEVELING)
MENU_ITEM_EDIT(float43, MSG_BED_Z, &mbl.z_offset, -1, 1);
#endif
//
// Nozzle:
// Nozzle [1-4]:
//
#if HOTENDS == 1
#if TEMP_SENSOR_0 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
#endif
#else //HOTENDS > 1
#if TEMP_SENSOR_0 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
#endif
#if TEMP_SENSOR_1 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
#endif
#if HOTENDS > 2
#if TEMP_SENSOR_2 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
#endif
#if HOTENDS > 3
#if TEMP_SENSOR_3 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
#endif
#endif // HOTENDS > 3
#endif // HOTENDS > 2
#endif // HOTENDS > 1
//
// Bed:
//
#if TEMP_SENSOR_BED != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed);
#endif
//
// Fan Speed:
//
#if FAN_COUNT > 0
#if HAS_FAN0
#if FAN_COUNT > 1
#define MSG_1ST_FAN_SPEED MSG_FAN_SPEED " 1"
#else
#define MSG_1ST_FAN_SPEED MSG_FAN_SPEED
#endif
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_1ST_FAN_SPEED, &fanSpeeds[0], 0, 255);
#endif
#if HAS_FAN1
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED " 2", &fanSpeeds[1], 0, 255);
#endif
#if HAS_FAN2
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED " 3", &fanSpeeds[2], 0, 255);
#endif
#endif // FAN_COUNT > 0
//
// Flow:
// Flow 1:
// Flow 2:
// Flow 3:
// Flow 4:
//
#if EXTRUDERS == 1
MENU_ITEM_EDIT(int3, MSG_FLOW, &flow_percentage[0], 10, 999);
#else // EXTRUDERS > 1
MENU_ITEM_EDIT(int3, MSG_FLOW, &flow_percentage[active_extruder], 10, 999);
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N1, &flow_percentage[0], 10, 999);
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N2, &flow_percentage[1], 10, 999);
#if EXTRUDERS > 2
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N3, &flow_percentage[2], 10, 999);
#if EXTRUDERS > 3
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N4, &flow_percentage[3], 10, 999);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
//
// Babystep X:
// Babystep Y:
// Babystep Z:
//
#if ENABLED(BABYSTEPPING)
#if ENABLED(BABYSTEP_XY)
MENU_ITEM(submenu, MSG_BABYSTEP_X, lcd_babystep_x);
MENU_ITEM(submenu, MSG_BABYSTEP_Y, lcd_babystep_y);
#endif //BABYSTEP_XY
MENU_ITEM(submenu, MSG_BABYSTEP_Z, lcd_babystep_z);
#endif
//
// Change filament
//
#if ENABLED(FILAMENT_CHANGE_FEATURE)
MENU_ITEM(function, MSG_FILAMENTCHANGE, lcd_enqueue_filament_change);
#endif
END_MENU();
}
/**
*
* "Driver current control" submenu items
*
*/
#if ENABLED(DAC_STEPPER_CURRENT)
void dac_driver_getValues() { LOOP_XYZE(i) driverPercent[i] = dac_current_get_percent((AxisEnum)i); }
void dac_driver_commit() { dac_current_set_percents(driverPercent); }
void dac_driver_eeprom_write() { dac_commit_eeprom(); }
void lcd_dac_menu() {
dac_driver_getValues();
START_MENU();
MENU_BACK(MSG_CONTROL);
MENU_ITEM_EDIT_CALLBACK(int3, MSG_X " " MSG_DAC_PERCENT, &driverPercent[X_AXIS], 0, 100, dac_driver_commit);
MENU_ITEM_EDIT_CALLBACK(int3, MSG_Y " " MSG_DAC_PERCENT, &driverPercent[Y_AXIS], 0, 100, dac_driver_commit);
MENU_ITEM_EDIT_CALLBACK(int3, MSG_Z " " MSG_DAC_PERCENT, &driverPercent[Z_AXIS], 0, 100, dac_driver_commit);
MENU_ITEM_EDIT_CALLBACK(int3, MSG_E " " MSG_DAC_PERCENT, &driverPercent[E_AXIS], 0, 100, dac_driver_commit);
MENU_ITEM(function, MSG_DAC_EEPROM_WRITE, dac_driver_eeprom_write);
END_MENU();
}
#endif
/**
*
* "Prepare" submenu items
*
*/
void _lcd_preheat(int endnum, const float temph, const float tempb, const int fan) {
if (temph > 0) thermalManager.setTargetHotend(temph, endnum);
#if TEMP_SENSOR_BED != 0
thermalManager.setTargetBed(tempb);
#else
UNUSED(tempb);
#endif
#if FAN_COUNT > 0
#if FAN_COUNT > 1
fanSpeeds[active_extruder < FAN_COUNT ? active_extruder : 0] = fan;
#else
fanSpeeds[0] = fan;
#endif
#else
UNUSED(fan);
#endif
lcd_return_to_status();
}
#if TEMP_SENSOR_0 != 0
void lcd_preheat_material1_hotend0() { _lcd_preheat(0, lcd_preheat_hotend_temp[0], lcd_preheat_bed_temp[0], lcd_preheat_fan_speed[0]); }
void lcd_preheat_material2_hotend0() { _lcd_preheat(0, lcd_preheat_hotend_temp[1], lcd_preheat_bed_temp[1], lcd_preheat_fan_speed[1]); }
#endif
#if HOTENDS > 1
void lcd_preheat_material1_hotend1() { _lcd_preheat(1, lcd_preheat_hotend_temp[0], lcd_preheat_bed_temp[0], lcd_preheat_fan_speed[0]); }
void lcd_preheat_material2_hotend1() { _lcd_preheat(1, lcd_preheat_hotend_temp[1], lcd_preheat_bed_temp[1], lcd_preheat_fan_speed[1]); }
#if HOTENDS > 2
void lcd_preheat_material1_hotend2() { _lcd_preheat(2, lcd_preheat_hotend_temp[0], lcd_preheat_bed_temp[0], lcd_preheat_fan_speed[0]); }
void lcd_preheat_material2_hotend2() { _lcd_preheat(2, lcd_preheat_hotend_temp[1], lcd_preheat_bed_temp[1], lcd_preheat_fan_speed[1]); }
#if HOTENDS > 3
void lcd_preheat_material1_hotend3() { _lcd_preheat(3, lcd_preheat_hotend_temp[0], lcd_preheat_bed_temp[0], lcd_preheat_fan_speed[0]); }
void lcd_preheat_material2_hotend3() { _lcd_preheat(3, lcd_preheat_hotend_temp[1], lcd_preheat_bed_temp[1], lcd_preheat_fan_speed[1]); }
#endif
#endif
void lcd_preheat_material1_hotend0123() {
#if HOTENDS > 1
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[0], 1);
#if HOTENDS > 2
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[0], 2);
#if HOTENDS > 3
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[0], 3);
#endif
#endif
#endif
lcd_preheat_material1_hotend0();
}
void lcd_preheat_material2_hotend0123() {
#if HOTENDS > 1
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[1], 1);
#if HOTENDS > 2
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[1], 2);
#if HOTENDS > 3
thermalManager.setTargetHotend(lcd_preheat_hotend_temp[1], 3);
#endif
#endif
#endif
lcd_preheat_material2_hotend0();
}
#endif // HOTENDS > 1
#if TEMP_SENSOR_BED != 0
void lcd_preheat_material1_bedonly() { _lcd_preheat(0, 0, lcd_preheat_bed_temp[0], lcd_preheat_fan_speed[0]); }
void lcd_preheat_material2_bedonly() { _lcd_preheat(0, 0, lcd_preheat_bed_temp[1], lcd_preheat_fan_speed[1]); }
#endif
#if TEMP_SENSOR_0 != 0 && (TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0)
void lcd_preheat_material1_menu() {
START_MENU();
MENU_BACK(MSG_PREPARE);
#if HOTENDS == 1
MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_material1_hotend0);
#else
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H1, lcd_preheat_material1_hotend0);
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H2, lcd_preheat_material1_hotend1);
#if HOTENDS > 2
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H3, lcd_preheat_material1_hotend2);
#if HOTENDS > 3
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H4, lcd_preheat_material1_hotend3);
#endif
#endif
MENU_ITEM(function, MSG_PREHEAT_1_ALL, lcd_preheat_material1_hotend0123);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_1_BEDONLY, lcd_preheat_material1_bedonly);
#endif
END_MENU();
}
void lcd_preheat_material2_menu() {
START_MENU();
MENU_BACK(MSG_PREPARE);
#if HOTENDS == 1
MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_material2_hotend0);
#else
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H1, lcd_preheat_material2_hotend0);
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H2, lcd_preheat_material2_hotend1);
#if HOTENDS > 2
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H3, lcd_preheat_material2_hotend2);
#if HOTENDS > 3
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H4, lcd_preheat_material2_hotend3);
#endif
#endif
MENU_ITEM(function, MSG_PREHEAT_2_ALL, lcd_preheat_material2_hotend0123);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_2_BEDONLY, lcd_preheat_material2_bedonly);
#endif
END_MENU();
}
#endif // TEMP_SENSOR_0 && (TEMP_SENSOR_1 || TEMP_SENSOR_2 || TEMP_SENSOR_3 || TEMP_SENSOR_BED)
void lcd_cooldown() {
#if FAN_COUNT > 0
for (uint8_t i = 0; i < FAN_COUNT; i++) fanSpeeds[i] = 0;
#endif
thermalManager.disable_all_heaters();
lcd_return_to_status();
}
#if ENABLED(SDSUPPORT) && ENABLED(MENU_ADDAUTOSTART)
void lcd_autostart_sd() {
card.autostart_index = 0;
card.setroot();
card.checkautostart(true);
}
#endif
#if ENABLED(MANUAL_BED_LEVELING)
/**
*
* "Prepare" > "Bed Leveling" handlers
*
*/
static uint8_t _lcd_level_bed_position;
// Utility to go to the next mesh point
// A raise is added between points if Z_HOMING_HEIGHT is in use
// Note: During Manual Bed Leveling the homed Z position is MESH_HOME_SEARCH_Z
// Z position will be restored with the final action, a G28
inline void _mbl_goto_xy(float x, float y) {
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT);
line_to_current(Z_AXIS);
current_position[X_AXIS] = LOGICAL_X_POSITION(x);
current_position[Y_AXIS] = LOGICAL_Y_POSITION(y);
planner.buffer_line_kinematic(current_position, MMM_TO_MMS(XY_PROBE_SPEED), active_extruder);
#if Z_HOMING_HEIGHT > 0
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z);
line_to_current(Z_AXIS);
#endif
stepper.synchronize();
}
void _lcd_level_goto_next_point();
void _lcd_level_bed_done() {
if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_DONE));
lcdDrawUpdate =
#if ENABLED(DOGLCD)
LCDVIEW_CALL_REDRAW_NEXT
#else
LCDVIEW_CALL_NO_REDRAW
#endif
;
}
/**
* Step 7: Get the Z coordinate, then goto next point or exit
*/
void _lcd_level_bed_get_z() {
ENCODER_DIRECTION_NORMAL();
// Encoder wheel adjusts the Z position
if (encoderPosition) {
refresh_cmd_timeout();
current_position[Z_AXIS] += float((int32_t)encoderPosition) * (MBL_Z_STEP);
NOLESS(current_position[Z_AXIS], 0);
NOMORE(current_position[Z_AXIS], MESH_HOME_SEARCH_Z * 2);
line_to_current(Z_AXIS);
lcdDrawUpdate =
#if ENABLED(DOGLCD)
LCDVIEW_CALL_REDRAW_NEXT
#else
LCDVIEW_REDRAW_NOW
#endif
;
encoderPosition = 0;
}
static bool debounce_click = false;
if (lcd_clicked) {
if (!debounce_click) {
debounce_click = true; // ignore multiple "clicks" in a row
mbl.set_zigzag_z(_lcd_level_bed_position++, current_position[Z_AXIS]);
if (_lcd_level_bed_position == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) {
lcd_goto_screen(_lcd_level_bed_done);
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT;
line_to_current(Z_AXIS);
stepper.synchronize();
mbl.set_has_mesh(true);
enqueue_and_echo_commands_P(PSTR("G28"));
lcd_return_to_status();
//LCD_MESSAGEPGM(MSG_LEVEL_BED_DONE);
#if HAS_BUZZER
lcd_buzz(200, 659);
lcd_buzz(200, 698);
#endif
}
else {
lcd_goto_screen(_lcd_level_goto_next_point);
}
}
}
else {
debounce_click = false;
}
// Update on first display, then only on updates to Z position
// Show message above on clicks instead
if (lcdDrawUpdate) {
float v = current_position[Z_AXIS] - MESH_HOME_SEARCH_Z;
lcd_implementation_drawedit(PSTR(MSG_MOVE_Z), ftostr43sign(v + (v < 0 ? -0.0001 : 0.0001), '+'));
}
}
/**
* Step 6: Display "Next point: 1 / 9" while waiting for move to finish
*/
void _lcd_level_bed_moving() {
if (lcdDrawUpdate) {
char msg[10];
sprintf_P(msg, PSTR("%i / %u"), (int)(_lcd_level_bed_position + 1), (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS));
lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_NEXT_POINT), msg);
}
lcdDrawUpdate =
#if ENABLED(DOGLCD)
LCDVIEW_CALL_REDRAW_NEXT
#else
LCDVIEW_CALL_NO_REDRAW
#endif
;
}
/**
* Step 5: Initiate a move to the next point
*/
void _lcd_level_goto_next_point() {
// Set the menu to display ahead of blocking call
lcd_goto_screen(_lcd_level_bed_moving);
// _mbl_goto_xy runs the menu loop until the move is done
int8_t px, py;
mbl.zigzag(_lcd_level_bed_position, px, py);
_mbl_goto_xy(mbl.get_probe_x(px), mbl.get_probe_y(py));
// After the blocking function returns, change menus
lcd_goto_screen(_lcd_level_bed_get_z);
}
/**
* Step 4: Display "Click to Begin", wait for click
* Move to the first probe position
*/
void _lcd_level_bed_homing_done() {
if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_WAITING));
if (lcd_clicked) {
_lcd_level_bed_position = 0;
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
#if Z_HOME_DIR > 0
+ Z_MAX_POS
#endif
;
planner.set_position_mm(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
lcd_goto_screen(_lcd_level_goto_next_point);
}
}
/**
* Step 3: Display "Homing XYZ" - Wait for homing to finish
*/
void _lcd_level_bed_homing() {
if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_HOMING), NULL);
lcdDrawUpdate =
#if ENABLED(DOGLCD)
LCDVIEW_CALL_REDRAW_NEXT
#else
LCDVIEW_CALL_NO_REDRAW
#endif
;
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
lcd_goto_screen(_lcd_level_bed_homing_done);
}
/**
* Step 2: Continue Bed Leveling...
*/
void _lcd_level_bed_continue() {
defer_return_to_status = true;
axis_homed[X_AXIS] = axis_homed[Y_AXIS] = axis_homed[Z_AXIS] = false;
mbl.reset();
enqueue_and_echo_commands_P(PSTR("G28"));
lcd_goto_screen(_lcd_level_bed_homing);
}
/**
* Step 1: MBL entry-point: "Cancel" or "Level Bed"
*/
void lcd_level_bed() {
START_MENU();
MENU_BACK(MSG_LEVEL_BED_CANCEL);
MENU_ITEM(submenu, MSG_LEVEL_BED, _lcd_level_bed_continue);
END_MENU();
}
#endif // MANUAL_BED_LEVELING
/**
*
* "Prepare" submenu
*
*/
void lcd_prepare_menu() {
START_MENU();
//
// ^ Main
//
MENU_BACK(MSG_MAIN);
//
// Auto Home
//
MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
#if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU)
MENU_ITEM(gcode, MSG_AUTO_HOME_X, PSTR("G28 X"));
MENU_ITEM(gcode, MSG_AUTO_HOME_Y, PSTR("G28 Y"));
MENU_ITEM(gcode, MSG_AUTO_HOME_Z, PSTR("G28 Z"));
#endif
//
// Set Home Offsets
//
MENU_ITEM(function, MSG_SET_HOME_OFFSETS, lcd_set_home_offsets);
//MENU_ITEM(gcode, MSG_SET_ORIGIN, PSTR("G92 X0 Y0 Z0"));
//
// Level Bed
//
#if HAS_ABL
MENU_ITEM(gcode, MSG_LEVEL_BED,
axis_homed[X_AXIS] && axis_homed[Y_AXIS] ? PSTR("G29") : PSTR("G28\nG29")
);
#elif ENABLED(MANUAL_BED_LEVELING)
MENU_ITEM(submenu, MSG_LEVEL_BED, lcd_level_bed);
#endif
//
// Move Axis
//
MENU_ITEM(submenu, MSG_MOVE_AXIS, lcd_move_menu);
//
// Disable Steppers
//
MENU_ITEM(gcode, MSG_DISABLE_STEPPERS, PSTR("M84"));
//
// Preheat PLA
// Preheat ABS
//
#if TEMP_SENSOR_0 != 0
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0
MENU_ITEM(submenu, MSG_PREHEAT_1, lcd_preheat_material1_menu);
MENU_ITEM(submenu, MSG_PREHEAT_2, lcd_preheat_material2_menu);
#else
MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_material1_hotend0);
MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_material2_hotend0);
#endif
#endif
//
// Cooldown
//
MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
//
// BLTouch Self-Test and Reset
//
#if ENABLED(BLTOUCH)
MENU_ITEM(gcode, MSG_BLTOUCH_SELFTEST, PSTR("M280 P" STRINGIFY(Z_ENDSTOP_SERVO_NR) " S" STRINGIFY(BLTOUCH_SELFTEST)));
if (!endstops.z_probe_enabled && TEST_BLTOUCH())
MENU_ITEM(gcode, MSG_BLTOUCH_RESET, PSTR("M280 P" STRINGIFY(Z_ENDSTOP_SERVO_NR) " S" STRINGIFY(BLTOUCH_RESET)));
#endif
//
// Switch power on/off
//
#if HAS_POWER_SWITCH
if (powersupply)
MENU_ITEM(gcode, MSG_SWITCH_PS_OFF, PSTR("M81"));
else
MENU_ITEM(gcode, MSG_SWITCH_PS_ON, PSTR("M80"));
#endif
//
// Autostart
//
#if ENABLED(SDSUPPORT) && ENABLED(MENU_ADDAUTOSTART)
MENU_ITEM(function, MSG_AUTOSTART, lcd_autostart_sd);
#endif
END_MENU();
}
#if ENABLED(DELTA_CALIBRATION_MENU)
void _goto_tower_pos(const float &a) {
do_blocking_move_to(
a < 0 ? X_HOME_POS : sin(a) * -(DELTA_PRINTABLE_RADIUS),
a < 0 ? Y_HOME_POS : cos(a) * (DELTA_PRINTABLE_RADIUS),
4
);
}
void _goto_tower_x() { _goto_tower_pos(RADIANS(120)); }
void _goto_tower_y() { _goto_tower_pos(RADIANS(240)); }
void _goto_tower_z() { _goto_tower_pos(0); }
void _goto_center() { _goto_tower_pos(-1); }
void lcd_delta_calibrate_menu() {
START_MENU();
MENU_BACK(MSG_MAIN);
MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
MENU_ITEM(function, MSG_DELTA_CALIBRATE_X, _goto_tower_x);
MENU_ITEM(function, MSG_DELTA_CALIBRATE_Y, _goto_tower_y);
MENU_ITEM(function, MSG_DELTA_CALIBRATE_Z, _goto_tower_z);
MENU_ITEM(function, MSG_DELTA_CALIBRATE_CENTER, _goto_center);
END_MENU();
}
#endif // DELTA_CALIBRATION_MENU
float move_menu_scale;
/**
* If the most recent manual move hasn't been fed to the planner yet,
* and the planner can accept one, send immediately
*/
inline void manage_manual_move() {
if (manual_move_axis != (int8_t)NO_AXIS && ELAPSED(millis(), manual_move_start_time) && !planner.is_full()) {
planner.buffer_line_kinematic(current_position, MMM_TO_MMS(manual_feedrate_mm_m[manual_move_axis]), manual_move_e_index);
manual_move_axis = (int8_t)NO_AXIS;
}
}
/**
* Set a flag that lcd_update() should start a move
* to "current_position" after a short delay.
*/
inline void manual_move_to_current(AxisEnum axis
#if E_MANUAL > 1
, int8_t eindex=-1
#endif
) {
#if E_MANUAL > 1
if (axis == E_AXIS) manual_move_e_index = eindex >= 0 ? eindex : active_extruder;
#endif
manual_move_start_time = millis() + (move_menu_scale < 0.99 ? 0UL : 250UL); // delay for bigger moves
manual_move_axis = (int8_t)axis;
}
/**
*
* "Prepare" > "Move Axis" submenu
*
*/
void _lcd_move_xyz(const char* name, AxisEnum axis) {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
ENCODER_DIRECTION_NORMAL();
if (encoderPosition) {
refresh_cmd_timeout();
// Limit to software endstops, if enabled
float min = (soft_endstops_enabled && min_software_endstops) ? soft_endstop_min[axis] : current_position[axis] - 1000,
max = (soft_endstops_enabled && max_software_endstops) ? soft_endstop_max[axis] : current_position[axis] + 1000;
// Get the new position
current_position[axis] += float((int32_t)encoderPosition) * move_menu_scale;
// Delta limits XY based on the current offset from center
// This assumes the center is 0,0
#if ENABLED(DELTA)
if (axis != Z_AXIS) {
max = sqrt(sq(DELTA_PRINTABLE_RADIUS) - sq(current_position[Y_AXIS - axis]));
min = -max;
}
#endif
// Limit only when trying to move towards the limit
if ((int32_t)encoderPosition < 0) NOLESS(current_position[axis], min);
if ((int32_t)encoderPosition > 0) NOMORE(current_position[axis], max);
manual_move_to_current(axis);
encoderPosition = 0;
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
}
if (lcdDrawUpdate) lcd_implementation_drawedit(name, ftostr41sign(current_position[axis]));
}
void lcd_move_x() { _lcd_move_xyz(PSTR(MSG_MOVE_X), X_AXIS); }
void lcd_move_y() { _lcd_move_xyz(PSTR(MSG_MOVE_Y), Y_AXIS); }
void lcd_move_z() { _lcd_move_xyz(PSTR(MSG_MOVE_Z), Z_AXIS); }
void _lcd_move_e(
#if E_MANUAL > 1
int8_t eindex=-1
#endif
) {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
ENCODER_DIRECTION_NORMAL();
if (encoderPosition) {
current_position[E_AXIS] += float((int32_t)encoderPosition) * move_menu_scale;
encoderPosition = 0;
manual_move_to_current(E_AXIS
#if E_MANUAL > 1
, eindex
#endif
);
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
}
if (lcdDrawUpdate) {
PGM_P pos_label;
#if E_MANUAL == 1
pos_label = PSTR(MSG_MOVE_E);
#else
switch (eindex) {
default: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E1); break;
case 1: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E2); break;
#if E_MANUAL > 2
case 2: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E3); break;
#if E_MANUAL > 3
case 3: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E4); break;
#endif
#endif
}
#endif
lcd_implementation_drawedit(pos_label, ftostr41sign(current_position[E_AXIS]));
}
}
void lcd_move_e() { _lcd_move_e(); }
#if E_MANUAL > 1
void lcd_move_e0() { _lcd_move_e(0); }
void lcd_move_e1() { _lcd_move_e(1); }
#if E_MANUAL > 2
void lcd_move_e2() { _lcd_move_e(2); }
#if E_MANUAL > 3
void lcd_move_e3() { _lcd_move_e(3); }
#endif
#endif
#endif
/**
*
* "Prepare" > "Move Xmm" > "Move XYZ" submenu
*
*/
#if IS_KINEMATIC
#define _MOVE_XYZ_ALLOWED (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
#else
#define _MOVE_XYZ_ALLOWED true
#endif
void _lcd_move_menu_axis() {
START_MENU();
MENU_BACK(MSG_MOVE_AXIS);
if (_MOVE_XYZ_ALLOWED) {
MENU_ITEM(submenu, MSG_MOVE_X, lcd_move_x);
MENU_ITEM(submenu, MSG_MOVE_Y, lcd_move_y);
}
if (move_menu_scale < 10.0) {
if (_MOVE_XYZ_ALLOWED) MENU_ITEM(submenu, MSG_MOVE_Z, lcd_move_z);
#if ENABLED(SWITCHING_EXTRUDER)
if (active_extruder)
MENU_ITEM(gcode, MSG_SELECT MSG_E1, PSTR("T0"));
else
MENU_ITEM(gcode, MSG_SELECT MSG_E2, PSTR("T1"));
#endif
MENU_ITEM(submenu, MSG_MOVE_E, lcd_move_e);
#if E_MANUAL > 1
MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E1, lcd_move_e0);
MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E2, lcd_move_e1);
#if E_MANUAL > 2
MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E3, lcd_move_e2);
#if E_MANUAL > 3
MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E4, lcd_move_e3);
#endif
#endif
#endif
}
END_MENU();
}
void lcd_move_menu_10mm() {
move_menu_scale = 10.0;
_lcd_move_menu_axis();
}
void lcd_move_menu_1mm() {
move_menu_scale = 1.0;
_lcd_move_menu_axis();
}
void lcd_move_menu_01mm() {
move_menu_scale = 0.1;
_lcd_move_menu_axis();
}
/**
*
* "Prepare" > "Move Axis" submenu
*
*/
void lcd_move_menu() {
START_MENU();
MENU_BACK(MSG_PREPARE);
if (_MOVE_XYZ_ALLOWED)
MENU_ITEM(submenu, MSG_MOVE_10MM, lcd_move_menu_10mm);
MENU_ITEM(submenu, MSG_MOVE_1MM, lcd_move_menu_1mm);
MENU_ITEM(submenu, MSG_MOVE_01MM, lcd_move_menu_01mm);
//TODO:X,Y,Z,E
END_MENU();
}
/**
*
* "Control" submenu
*
*/
void lcd_control_menu() {
START_MENU();
MENU_BACK(MSG_MAIN);
MENU_ITEM(submenu, MSG_TEMPERATURE, lcd_control_temperature_menu);
MENU_ITEM(submenu, MSG_MOTION, lcd_control_motion_menu);
MENU_ITEM(submenu, MSG_VOLUMETRIC, lcd_control_volumetric_menu);
#if HAS_LCD_CONTRAST
//MENU_ITEM_EDIT(int3, MSG_CONTRAST, &lcd_contrast, 0, 63);
MENU_ITEM(submenu, MSG_CONTRAST, lcd_set_contrast);
#endif
#if ENABLED(FWRETRACT)
MENU_ITEM(submenu, MSG_RETRACT, lcd_control_retract_menu);
#endif
#if ENABLED(DAC_STEPPER_CURRENT)
MENU_ITEM(submenu, MSG_DRIVE_STRENGTH, lcd_dac_menu);
#endif
#if ENABLED(EEPROM_SETTINGS)
MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);
MENU_ITEM(function, MSG_LOAD_EPROM, Config_RetrieveSettings);
#endif
MENU_ITEM(function, MSG_RESTORE_FAILSAFE, Config_ResetDefault);
END_MENU();
}
/**
*
* "Temperature" submenu
*
*/
#if ENABLED(PID_AUTOTUNE_MENU)
#if ENABLED(PIDTEMP)
int autotune_temp[HOTENDS] = ARRAY_BY_HOTENDS1(150);
const int heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP);
#endif
#if ENABLED(PIDTEMPBED)
int autotune_temp_bed = 70;
#endif
void _lcd_autotune(int e) {
char cmd[30];
sprintf_P(cmd, PSTR("M303 U1 E%i S%i"), e,
#if HAS_PID_FOR_BOTH
e < 0 ? autotune_temp_bed : autotune_temp[e]
#elif ENABLED(PIDTEMPBED)
autotune_temp_bed
#else
autotune_temp[e]
#endif
);
enqueue_and_echo_command(cmd);
}
#endif //PID_AUTOTUNE_MENU
#if ENABLED(PIDTEMP)
// Helpers for editing PID Ki & Kd values
// grab the PID value out of the temp variable; scale it; then update the PID driver
void copy_and_scalePID_i(int e) {
#if DISABLED(PID_PARAMS_PER_HOTEND) || HOTENDS == 1
UNUSED(e);
#endif
PID_PARAM(Ki, e) = scalePID_i(raw_Ki);
thermalManager.updatePID();
}
void copy_and_scalePID_d(int e) {
#if DISABLED(PID_PARAMS_PER_HOTEND) || HOTENDS == 1
UNUSED(e);
#endif
PID_PARAM(Kd, e) = scalePID_d(raw_Kd);
thermalManager.updatePID();
}
#define _PIDTEMP_BASE_FUNCTIONS(eindex) \
void copy_and_scalePID_i_E ## eindex() { copy_and_scalePID_i(eindex); } \
void copy_and_scalePID_d_E ## eindex() { copy_and_scalePID_d(eindex); }
#if ENABLED(PID_AUTOTUNE_MENU)
#define _PIDTEMP_FUNCTIONS(eindex) \
_PIDTEMP_BASE_FUNCTIONS(eindex); \
void lcd_autotune_callback_E ## eindex() { _lcd_autotune(eindex); }
#else
#define _PIDTEMP_FUNCTIONS(eindex) _PIDTEMP_BASE_FUNCTIONS(eindex)
#endif
_PIDTEMP_FUNCTIONS(0)
#if ENABLED(PID_PARAMS_PER_HOTEND)
#if HOTENDS > 1
_PIDTEMP_FUNCTIONS(1)
#if HOTENDS > 2
_PIDTEMP_FUNCTIONS(2)
#if HOTENDS > 3
_PIDTEMP_FUNCTIONS(3)
#endif //HOTENDS > 3
#endif //HOTENDS > 2
#endif //HOTENDS > 1
#endif //PID_PARAMS_PER_HOTEND
#endif //PIDTEMP
/**
*
* "Control" > "Temperature" submenu
*
*/
void lcd_control_temperature_menu() {
START_MENU();
//
// ^ Control
//
MENU_BACK(MSG_CONTROL);
//
// Nozzle:
// Nozzle [1-4]:
//
#if HOTENDS == 1
#if TEMP_SENSOR_0 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
#endif
#else //HOTENDS > 1
#if TEMP_SENSOR_0 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
#endif
#if TEMP_SENSOR_1 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
#endif
#if HOTENDS > 2
#if TEMP_SENSOR_2 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
#endif
#if HOTENDS > 3
#if TEMP_SENSOR_3 != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
#endif
#endif // HOTENDS > 3
#endif // HOTENDS > 2
#endif // HOTENDS > 1
//
// Bed:
//
#if TEMP_SENSOR_BED != 0
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed);
#endif
//
// Fan Speed:
//
#if FAN_COUNT > 0
#if HAS_FAN0
#if FAN_COUNT > 1
#define MSG_1ST_FAN_SPEED MSG_FAN_SPEED " 1"
#else
#define MSG_1ST_FAN_SPEED MSG_FAN_SPEED
#endif
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_1ST_FAN_SPEED, &fanSpeeds[0], 0, 255);
#endif
#if HAS_FAN1
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED " 2", &fanSpeeds[1], 0, 255);
#endif
#if HAS_FAN2
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED " 3", &fanSpeeds[2], 0, 255);
#endif
#endif // FAN_COUNT > 0
//
// Autotemp, Min, Max, Fact
//
#if ENABLED(AUTOTEMP) && (TEMP_SENSOR_0 != 0)
MENU_ITEM_EDIT(bool, MSG_AUTOTEMP, &planner.autotemp_enabled);
MENU_ITEM_EDIT(float3, MSG_MIN, &planner.autotemp_min, 0, HEATER_0_MAXTEMP - 15);
MENU_ITEM_EDIT(float3, MSG_MAX, &planner.autotemp_max, 0, HEATER_0_MAXTEMP - 15);
MENU_ITEM_EDIT(float32, MSG_FACTOR, &planner.autotemp_factor, 0.0, 1.0);
#endif
//
// PID-P, PID-I, PID-D, PID-C, PID Autotune
// PID-P E1, PID-I E1, PID-D E1, PID-C E1, PID Autotune E1
// PID-P E2, PID-I E2, PID-D E2, PID-C E2, PID Autotune E2
// PID-P E3, PID-I E3, PID-D E3, PID-C E3, PID Autotune E3
// PID-P E4, PID-I E4, PID-D E4, PID-C E4, PID Autotune E4
//
#if ENABLED(PIDTEMP)
#define _PID_BASE_MENU_ITEMS(ELABEL, eindex) \
raw_Ki = unscalePID_i(PID_PARAM(Ki, eindex)); \
raw_Kd = unscalePID_d(PID_PARAM(Kd, eindex)); \
MENU_ITEM_EDIT(float52, MSG_PID_P ELABEL, &PID_PARAM(Kp, eindex), 1, 9990); \
MENU_ITEM_EDIT_CALLBACK(float52, MSG_PID_I ELABEL, &raw_Ki, 0.01, 9990, copy_and_scalePID_i_E ## eindex); \
MENU_ITEM_EDIT_CALLBACK(float52, MSG_PID_D ELABEL, &raw_Kd, 1, 9990, copy_and_scalePID_d_E ## eindex)
#if ENABLED(PID_EXTRUSION_SCALING)
#define _PID_MENU_ITEMS(ELABEL, eindex) \
_PID_BASE_MENU_ITEMS(ELABEL, eindex); \
MENU_ITEM_EDIT(float3, MSG_PID_C ELABEL, &PID_PARAM(Kc, eindex), 1, 9990)
#else
#define _PID_MENU_ITEMS(ELABEL, eindex) _PID_BASE_MENU_ITEMS(ELABEL, eindex)
#endif
#if ENABLED(PID_AUTOTUNE_MENU)
#define PID_MENU_ITEMS(ELABEL, eindex) \
_PID_MENU_ITEMS(ELABEL, eindex); \
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_PID_AUTOTUNE ELABEL, &autotune_temp[eindex], 150, heater_maxtemp[eindex] - 15, lcd_autotune_callback_E ## eindex)
#else
#define PID_MENU_ITEMS(ELABEL, eindex) _PID_MENU_ITEMS(ELABEL, eindex)
#endif
#if ENABLED(PID_PARAMS_PER_HOTEND) && HOTENDS > 1
PID_MENU_ITEMS(MSG_E1, 0);
PID_MENU_ITEMS(MSG_E2, 1);
#if HOTENDS > 2
PID_MENU_ITEMS(MSG_E3, 2);
#if HOTENDS > 3
PID_MENU_ITEMS(MSG_E4, 3);
#endif //HOTENDS > 3
#endif //HOTENDS > 2
#else //!PID_PARAMS_PER_HOTEND || HOTENDS == 1
PID_MENU_ITEMS("", 0);
#endif //!PID_PARAMS_PER_HOTEND || HOTENDS == 1
#endif //PIDTEMP
//
// Preheat Material 1 conf
//
MENU_ITEM(submenu, MSG_PREHEAT_1_SETTINGS, lcd_control_temperature_preheat_material1_settings_menu);
//
// Preheat Material 2 conf
//
MENU_ITEM(submenu, MSG_PREHEAT_2_SETTINGS, lcd_control_temperature_preheat_material2_settings_menu);
END_MENU();
}
void _lcd_control_temperature_preheat_settings_menu(uint8_t material) {
START_MENU();
MENU_BACK(MSG_TEMPERATURE);
MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &lcd_preheat_fan_speed[material], 0, 255);
#if TEMP_SENSOR_0 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE, &lcd_preheat_hotend_temp[material], HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM_EDIT(int3, MSG_BED, &lcd_preheat_bed_temp[material], BED_MINTEMP, BED_MAXTEMP - 15);
#endif
#if ENABLED(EEPROM_SETTINGS)
MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);
#endif
END_MENU();
}
/**
*
* "Temperature" > "Preheat Material 1 conf" submenu
*
*/
void lcd_control_temperature_preheat_material1_settings_menu() { _lcd_control_temperature_preheat_settings_menu(0); }
/**
*
* "Temperature" > "Preheat Material 2 conf" submenu
*
*/
void lcd_control_temperature_preheat_material2_settings_menu() { _lcd_control_temperature_preheat_settings_menu(1); }
void _reset_acceleration_rates() { planner.reset_acceleration_rates(); }
void _planner_refresh_positioning() { planner.refresh_positioning(); }
/**
*
* "Control" > "Motion" submenu
*
*/
void lcd_control_motion_menu() {
START_MENU();
MENU_BACK(MSG_CONTROL);
#if HAS_BED_PROBE
MENU_ITEM_EDIT(float32, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
#endif
// Manual bed leveling, Bed Z:
#if ENABLED(MANUAL_BED_LEVELING)
MENU_ITEM_EDIT(float43, MSG_BED_Z, &mbl.z_offset, -1, 1);
#endif
MENU_ITEM_EDIT(float5, MSG_ACC, &planner.acceleration, 10, 99000);
MENU_ITEM_EDIT(float3, MSG_VX_JERK, &planner.max_jerk[X_AXIS], 1, 990);
MENU_ITEM_EDIT(float3, MSG_VY_JERK, &planner.max_jerk[Y_AXIS], 1, 990);
#if ENABLED(DELTA)
MENU_ITEM_EDIT(float3, MSG_VZ_JERK, &planner.max_jerk[Z_AXIS], 1, 990);
#else
MENU_ITEM_EDIT(float52, MSG_VZ_JERK, &planner.max_jerk[Z_AXIS], 0.1, 990);
#endif
MENU_ITEM_EDIT(float3, MSG_VE_JERK, &planner.max_jerk[E_AXIS], 1, 990);
MENU_ITEM_EDIT(float3, MSG_VMAX MSG_X, &planner.max_feedrate_mm_s[X_AXIS], 1, 999);
MENU_ITEM_EDIT(float3, MSG_VMAX MSG_Y, &planner.max_feedrate_mm_s[Y_AXIS], 1, 999);
MENU_ITEM_EDIT(float3, MSG_VMAX MSG_Z, &planner.max_feedrate_mm_s[Z_AXIS], 1, 999);
MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E, &planner.max_feedrate_mm_s[E_AXIS], 1, 999);
MENU_ITEM_EDIT(float3, MSG_VMIN, &planner.min_feedrate_mm_s, 0, 999);
MENU_ITEM_EDIT(float3, MSG_VTRAV_MIN, &planner.min_travel_feedrate_mm_s, 0, 999);
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_X, &planner.max_acceleration_mm_per_s2[X_AXIS], 100, 99000, _reset_acceleration_rates);
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_Y, &planner.max_acceleration_mm_per_s2[Y_AXIS], 100, 99000, _reset_acceleration_rates);
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_Z, &planner.max_acceleration_mm_per_s2[Z_AXIS], 10, 99000, _reset_acceleration_rates);
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E, &planner.max_acceleration_mm_per_s2[E_AXIS], 100, 99000, _reset_acceleration_rates);
MENU_ITEM_EDIT(float5, MSG_A_RETRACT, &planner.retract_acceleration, 100, 99000);
MENU_ITEM_EDIT(float5, MSG_A_TRAVEL, &planner.travel_acceleration, 100, 99000);
MENU_ITEM_EDIT_CALLBACK(float62, MSG_XSTEPS, &planner.axis_steps_per_mm[X_AXIS], 5, 9999, _planner_refresh_positioning);
MENU_ITEM_EDIT_CALLBACK(float62, MSG_YSTEPS, &planner.axis_steps_per_mm[Y_AXIS], 5, 9999, _planner_refresh_positioning);
MENU_ITEM_EDIT_CALLBACK(float62, MSG_ZSTEPS, &planner.axis_steps_per_mm[Z_AXIS], 5, 9999, _planner_refresh_positioning);
MENU_ITEM_EDIT_CALLBACK(float62, MSG_ESTEPS, &planner.axis_steps_per_mm[E_AXIS], 5, 9999, _planner_refresh_positioning);
#if ENABLED(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
MENU_ITEM_EDIT(bool, MSG_ENDSTOP_ABORT, &stepper.abort_on_endstop_hit);
#endif
END_MENU();
}
/**
*
* "Control" > "Filament" submenu
*
*/
void lcd_control_volumetric_menu() {
START_MENU();
MENU_BACK(MSG_CONTROL);
MENU_ITEM_EDIT_CALLBACK(bool, MSG_VOLUMETRIC_ENABLED, &volumetric_enabled, calculate_volumetric_multipliers);
if (volumetric_enabled) {
#if EXTRUDERS == 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_DIAM, &filament_size[0], 1.5, 3.25, calculate_volumetric_multipliers);
#else //EXTRUDERS > 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_DIAM MSG_DIAM_E1, &filament_size[0], 1.5, 3.25, calculate_volumetric_multipliers);
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_DIAM MSG_DIAM_E2, &filament_size[1], 1.5, 3.25, calculate_volumetric_multipliers);
#if EXTRUDERS > 2
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_DIAM MSG_DIAM_E3, &filament_size[2], 1.5, 3.25, calculate_volumetric_multipliers);
#if EXTRUDERS > 3
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_DIAM MSG_DIAM_E4, &filament_size[3], 1.5, 3.25, calculate_volumetric_multipliers);
#endif //EXTRUDERS > 3
#endif //EXTRUDERS > 2
#endif //EXTRUDERS > 1
}
END_MENU();
}
/**
*
* "Control" > "Contrast" submenu
*
*/
#if HAS_LCD_CONTRAST
void lcd_set_contrast() {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
ENCODER_DIRECTION_NORMAL();
if (encoderPosition) {
set_lcd_contrast(lcd_contrast + encoderPosition);
encoderPosition = 0;
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
}
if (lcdDrawUpdate) {
lcd_implementation_drawedit(PSTR(MSG_CONTRAST),
#if LCD_CONTRAST_MAX >= 100
itostr3(lcd_contrast)
#else
itostr2(lcd_contrast)
#endif
);
}
}
#endif // HAS_LCD_CONTRAST
/**
*
* "Control" > "Retract" submenu
*
*/
#if ENABLED(FWRETRACT)
void lcd_control_retract_menu() {
START_MENU();
MENU_BACK(MSG_CONTROL);
MENU_ITEM_EDIT(bool, MSG_AUTORETRACT, &autoretract_enabled);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT, &retract_length, 0, 100);
#if EXTRUDERS > 1
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_SWAP, &retract_length_swap, 0, 100);
#endif
MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACTF, &retract_feedrate_mm_s, 1, 999);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_ZLIFT, &retract_zlift, 0, 999);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER, &retract_recover_length, 0, 100);
#if EXTRUDERS > 1
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER_SWAP, &retract_recover_length_swap, 0, 100);
#endif
MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACT_RECOVERF, &retract_recover_feedrate_mm_s, 1, 999);
END_MENU();
}
#endif // FWRETRACT
#if ENABLED(SDSUPPORT)
#if !PIN_EXISTS(SD_DETECT)
void lcd_sd_refresh() {
card.initsd();
encoderTopLine = 0;
}
#endif
void lcd_sd_updir() {
card.updir();
encoderTopLine = 0;
}
/**
*
* "Print from SD" submenu
*
*/
void lcd_sdcard_menu() {
ENCODER_DIRECTION_MENUS();
if (!lcdDrawUpdate && !lcd_clicked) return; // nothing to do (so don't thrash the SD card)
uint16_t fileCnt = card.getnrfilenames();
START_MENU();
MENU_BACK(MSG_MAIN);
card.getWorkDirName();
if (card.filename[0] == '/') {
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(function, LCD_STR_REFRESH MSG_REFRESH, lcd_sd_refresh);
#endif
}
else {
MENU_ITEM(function, LCD_STR_FOLDER "..", lcd_sd_updir);
}
for (uint16_t i = 0; i < fileCnt; i++) {
if (_menuLineNr == _thisItemNr) {
card.getfilename(
#if ENABLED(SDCARD_RATHERRECENTFIRST)
fileCnt-1 -
#endif
i
);
if (card.filenameIsDir)
MENU_ITEM(sddirectory, MSG_CARD_MENU, card.filename, card.longFilename);
else
MENU_ITEM(sdfile, MSG_CARD_MENU, card.filename, card.longFilename);
}
else {
MENU_ITEM_DUMMY();
}
}
END_MENU();
}
#endif //SDSUPPORT
#if ENABLED(LCD_INFO_MENU)
#if ENABLED(PRINTCOUNTER)
/**
*
* About Printer > Statistics submenu
*
*/
void lcd_info_stats_menu() {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
char buffer[21];
printStatistics stats = print_job_timer.getStats();
START_SCREEN(); // 12345678901234567890
STATIC_ITEM(MSG_INFO_PRINT_COUNT ": ", false, false, itostr3left(stats.totalPrints)); // Print Count: 999
STATIC_ITEM(MSG_INFO_COMPLETED_PRINTS": ", false, false, itostr3left(stats.finishedPrints)); // Completed : 666
duration_t elapsed = stats.printTime;
elapsed.toString(buffer);
STATIC_ITEM(MSG_INFO_PRINT_TIME ": ", false, false); // Total print Time:
STATIC_ITEM("", false, false, buffer); // 99y 364d 23h 59m 59s
elapsed = stats.longestPrint;
elapsed.toString(buffer);
STATIC_ITEM(MSG_INFO_PRINT_LONGEST ": ", false, false); // Longest job time:
STATIC_ITEM("", false, false, buffer); // 99y 364d 23h 59m 59s
sprintf_P(buffer, PSTR("%ld.%im"), long(stats.filamentUsed / 1000), int(stats.filamentUsed / 100) % 10);
STATIC_ITEM(MSG_INFO_PRINT_FILAMENT ": ", false, false); // Extruded total:
STATIC_ITEM("", false, false, buffer); // 125m
END_SCREEN();
}
#endif // PRINTCOUNTER
/**
*
* About Printer > Thermistors
*
*/
void lcd_info_thermistors_menu() {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
START_SCREEN();
#define THERMISTOR_ID TEMP_SENSOR_0
#include "thermistornames.h"
STATIC_ITEM("T0: " THERMISTOR_NAME, false, true);
STATIC_ITEM(MSG_INFO_MIN_TEMP ": " STRINGIFY(HEATER_0_MINTEMP), false);
STATIC_ITEM(MSG_INFO_MAX_TEMP ": " STRINGIFY(HEATER_0_MAXTEMP), false);
#if TEMP_SENSOR_1 != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_1
#include "thermistornames.h"
STATIC_ITEM("T1: " THERMISTOR_NAME, false, true);
STATIC_ITEM(MSG_INFO_MIN_TEMP ": " STRINGIFY(HEATER_1_MINTEMP), false);
STATIC_ITEM(MSG_INFO_MAX_TEMP ": " STRINGIFY(HEATER_1_MAXTEMP), false);
#endif
#if TEMP_SENSOR_2 != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_2
#include "thermistornames.h"
STATIC_ITEM("T2: " THERMISTOR_NAME, false, true);
STATIC_ITEM(MSG_INFO_MIN_TEMP ": " STRINGIFY(HEATER_2_MINTEMP), false);
STATIC_ITEM(MSG_INFO_MAX_TEMP ": " STRINGIFY(HEATER_2_MAXTEMP), false);
#endif
#if TEMP_SENSOR_3 != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_3
#include "thermistornames.h"
STATIC_ITEM("T3: " THERMISTOR_NAME, false, true);
STATIC_ITEM(MSG_INFO_MIN_TEMP ": " STRINGIFY(HEATER_3_MINTEMP), false);
STATIC_ITEM(MSG_INFO_MAX_TEMP ": " STRINGIFY(HEATER_3_MAXTEMP), false);
#endif
#if TEMP_SENSOR_BED != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_BED
#include "thermistornames.h"
STATIC_ITEM("TBed:" THERMISTOR_NAME, false, true);
STATIC_ITEM(MSG_INFO_MIN_TEMP ": " STRINGIFY(BED_MINTEMP), false);
STATIC_ITEM(MSG_INFO_MAX_TEMP ": " STRINGIFY(BED_MAXTEMP), false);
#endif
END_SCREEN();
}
/**
*
* About Printer > Board Info
*
*/
void lcd_info_board_menu() {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
START_SCREEN();
STATIC_ITEM(BOARD_NAME, true, true); // MyPrinterController
STATIC_ITEM(MSG_INFO_BAUDRATE ": " STRINGIFY(BAUDRATE), true); // Baud: 250000
STATIC_ITEM(MSG_INFO_PROTOCOL ": " PROTOCOL_VERSION, true); // Protocol: 1.0
#ifdef POWER_SUPPLY
#if (POWER_SUPPLY == 1)
STATIC_ITEM(MSG_INFO_PSU ": ATX", true); // Power Supply: ATX
#elif (POWER_SUPPLY == 2)
STATIC_ITEM(MSG_INFO_PSU ": XBox", true); // Power Supply: XBox
#endif
#endif // POWER_SUPPLY
END_SCREEN();
}
/**
*
* About Printer > Printer Info
*
*/
void lcd_info_printer_menu() {
if (lcd_clicked) { return lcd_goto_previous_menu(); }
START_SCREEN();
STATIC_ITEM(MSG_MARLIN, true, true); // Marlin
STATIC_ITEM(SHORT_BUILD_VERSION, true); // x.x.x-Branch
STATIC_ITEM(STRING_DISTRIBUTION_DATE, true); // YYYY-MM-DD HH:MM
STATIC_ITEM(MACHINE_NAME, true); // My3DPrinter
STATIC_ITEM(WEBSITE_URL, true); // www.my3dprinter.com
STATIC_ITEM(MSG_INFO_EXTRUDERS ": " STRINGIFY(EXTRUDERS), true); // Extruders: 2
END_SCREEN();
}
/**
*
* "About Printer" submenu
*
*/
void lcd_info_menu() {
START_MENU();
MENU_BACK(MSG_MAIN);
MENU_ITEM(submenu, MSG_INFO_PRINTER_MENU, lcd_info_printer_menu); // Printer Info >
MENU_ITEM(submenu, MSG_INFO_BOARD_MENU, lcd_info_board_menu); // Board Info >
MENU_ITEM(submenu, MSG_INFO_THERMISTOR_MENU, lcd_info_thermistors_menu); // Thermistors >
#if ENABLED(PRINTCOUNTER)
MENU_ITEM(submenu, MSG_INFO_STATS_MENU, lcd_info_stats_menu); // Printer Statistics >
#endif
END_MENU();
}
#endif // LCD_INFO_MENU
#if ENABLED(FILAMENT_CHANGE_FEATURE)
void lcd_filament_change_resume_print() {
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_RESUME_PRINT;
lcd_goto_screen(lcd_status_screen);
}
void lcd_filament_change_extrude_more() {
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_EXTRUDE_MORE;
}
void lcd_filament_change_option_menu() {
START_MENU();
#if LCD_HEIGHT > 2
STATIC_ITEM(MSG_FILAMENT_CHANGE_OPTION_HEADER, true, false);
#endif
MENU_ITEM(function, MSG_FILAMENT_CHANGE_OPTION_RESUME, lcd_filament_change_resume_print);
MENU_ITEM(function, MSG_FILAMENT_CHANGE_OPTION_EXTRUDE, lcd_filament_change_extrude_more);
END_MENU();
}
void lcd_filament_change_init_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_INIT_1);
#ifdef MSG_FILAMENT_CHANGE_INIT_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_INIT_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_INIT_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_INIT_3);
#endif
END_SCREEN();
}
void lcd_filament_change_unload_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_UNLOAD_1);
#ifdef MSG_FILAMENT_CHANGE_UNLOAD_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_UNLOAD_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_UNLOAD_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_UNLOAD_3);
#endif
END_SCREEN();
}
void lcd_filament_change_insert_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_INSERT_1);
#ifdef MSG_FILAMENT_CHANGE_INSERT_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_INSERT_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_INSERT_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_INSERT_3);
#endif
END_SCREEN();
}
void lcd_filament_change_load_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_LOAD_1);
#ifdef MSG_FILAMENT_CHANGE_LOAD_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_LOAD_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_LOAD_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_LOAD_3);
#endif
END_SCREEN();
}
void lcd_filament_change_extrude_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_EXTRUDE_1);
#ifdef MSG_FILAMENT_CHANGE_EXTRUDE_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_EXTRUDE_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_EXTRUDE_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_EXTRUDE_3);
#endif
END_SCREEN();
}
void lcd_filament_change_resume_message() {
START_SCREEN();
STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
STATIC_ITEM(MSG_FILAMENT_CHANGE_RESUME_1);
#ifdef MSG_FILAMENT_CHANGE_RESUME_2
STATIC_ITEM(MSG_FILAMENT_CHANGE_RESUME_2);
#endif
#ifdef MSG_FILAMENT_CHANGE_RESUME_3
STATIC_ITEM(MSG_FILAMENT_CHANGE_RESUME_3);
#endif
END_SCREEN();
}
void lcd_filament_change_show_message(const FilamentChangeMessage message) {
switch (message) {
case FILAMENT_CHANGE_MESSAGE_INIT:
defer_return_to_status = true;
lcd_goto_screen(lcd_filament_change_init_message);
break;
case FILAMENT_CHANGE_MESSAGE_UNLOAD:
lcd_goto_screen(lcd_filament_change_unload_message);
break;
case FILAMENT_CHANGE_MESSAGE_INSERT:
lcd_goto_screen(lcd_filament_change_insert_message);
break;
case FILAMENT_CHANGE_MESSAGE_LOAD:
lcd_goto_screen(lcd_filament_change_load_message);
break;
case FILAMENT_CHANGE_MESSAGE_EXTRUDE:
lcd_goto_screen(lcd_filament_change_extrude_message);
break;
case FILAMENT_CHANGE_MESSAGE_OPTION:
filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_WAIT_FOR;
lcd_goto_screen(lcd_filament_change_option_menu);
break;
case FILAMENT_CHANGE_MESSAGE_RESUME:
lcd_goto_screen(lcd_filament_change_resume_message);
break;
case FILAMENT_CHANGE_MESSAGE_STATUS:
lcd_return_to_status();
break;
}
}
#endif // FILAMENT_CHANGE_FEATURE
/**
*
* Functions for editing single values
*
* The "menu_edit_type" macro generates the functions needed to edit a numerical value.
*
* For example, menu_edit_type(int, int3, itostr3, 1) expands into these functions:
*
* bool _menu_edit_int3();
* void menu_edit_int3(); // edit int (interactively)
* void menu_edit_callback_int3(); // edit int (interactively) with callback on completion
* void _menu_action_setting_edit_int3(const char* pstr, int* ptr, int minValue, int maxValue);
* void menu_action_setting_edit_int3(const char* pstr, int* ptr, int minValue, int maxValue);
* void menu_action_setting_edit_callback_int3(const char* pstr, int* ptr, int minValue, int maxValue, screenFunc_t callback); // edit int with callback
*
* You can then use one of the menu macros to present the edit interface:
* MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_percentage, 10, 999)
*
* This expands into a more primitive menu item:
* MENU_ITEM(setting_edit_int3, MSG_SPEED, PSTR(MSG_SPEED), &feedrate_percentage, 10, 999)
*
*
* Also: MENU_MULTIPLIER_ITEM_EDIT, MENU_ITEM_EDIT_CALLBACK, and MENU_MULTIPLIER_ITEM_EDIT_CALLBACK
*
* menu_action_setting_edit_int3(PSTR(MSG_SPEED), &feedrate_percentage, 10, 999)
*/
#define menu_edit_type(_type, _name, _strFunc, scale) \
bool _menu_edit_ ## _name () { \
ENCODER_DIRECTION_NORMAL(); \
if ((int32_t)encoderPosition < 0) encoderPosition = 0; \
if ((int32_t)encoderPosition > maxEditValue) encoderPosition = maxEditValue; \
if (lcdDrawUpdate) \
lcd_implementation_drawedit(editLabel, _strFunc(((_type)((int32_t)encoderPosition + minEditValue)) / scale)); \
if (lcd_clicked) { \
*((_type*)editValue) = ((_type)((int32_t)encoderPosition + minEditValue)) / scale; \
lcd_goto_previous_menu(); \
} \
return lcd_clicked; \
} \
void menu_edit_ ## _name () { _menu_edit_ ## _name(); } \
void menu_edit_callback_ ## _name () { if (_menu_edit_ ## _name ()) (*callbackFunc)(); } \
void _menu_action_setting_edit_ ## _name (const char* pstr, _type* ptr, _type minValue, _type maxValue) { \
lcd_save_previous_menu(); \
\
lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW; \
\
editLabel = pstr; \
editValue = ptr; \
minEditValue = minValue * scale; \
maxEditValue = maxValue * scale - minEditValue; \
encoderPosition = (*ptr) * scale - minEditValue; \
} \
void menu_action_setting_edit_ ## _name (const char* pstr, _type* ptr, _type minValue, _type maxValue) { \
_menu_action_setting_edit_ ## _name(pstr, ptr, minValue, maxValue); \
currentScreen = menu_edit_ ## _name; \
}\
void menu_action_setting_edit_callback_ ## _name (const char* pstr, _type* ptr, _type minValue, _type maxValue, screenFunc_t callback) { \
_menu_action_setting_edit_ ## _name(pstr, ptr, minValue, maxValue); \
currentScreen = menu_edit_callback_ ## _name; \
callbackFunc = callback; \
}
menu_edit_type(int, int3, itostr3, 1)
menu_edit_type(float, float3, ftostr3, 1)
menu_edit_type(float, float32, ftostr32, 100)
menu_edit_type(float, float43, ftostr43sign, 1000)
menu_edit_type(float, float5, ftostr5rj, 0.01)
menu_edit_type(float, float51, ftostr51sign, 10)
menu_edit_type(float, float52, ftostr52sign, 100)
menu_edit_type(float, float62, ftostr62sign, 100)
menu_edit_type(unsigned long, long5, ftostr5rj, 0.01)
/**
*
* Handlers for RepRap World Keypad input
*
*/
#if ENABLED(REPRAPWORLD_KEYPAD)
void _reprapworld_keypad_move(AxisEnum axis, int dir) {
move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP;
encoderPosition = dir;
switch (axis) {
case X_AXIS: lcd_move_x(); break;
case Y_AXIS: lcd_move_y(); break;
case Z_AXIS: lcd_move_z();
default: break;
}
}
void reprapworld_keypad_move_z_up() { _reprapworld_keypad_move(Z_AXIS, 1); }
void reprapworld_keypad_move_z_down() { _reprapworld_keypad_move(Z_AXIS, -1); }
void reprapworld_keypad_move_x_left() { _reprapworld_keypad_move(X_AXIS, -1); }
void reprapworld_keypad_move_x_right() { _reprapworld_keypad_move(X_AXIS, 1); }
void reprapworld_keypad_move_y_up() { _reprapworld_keypad_move(Y_AXIS, -1); }
void reprapworld_keypad_move_y_down() { _reprapworld_keypad_move(Y_AXIS, 1); }
void reprapworld_keypad_move_home() { enqueue_and_echo_commands_P(PSTR("G28")); } // move all axes home and wait
void reprapworld_keypad_move_menu() { lcd_goto_screen(lcd_move_menu); }
#endif // REPRAPWORLD_KEYPAD
/**
*
* Audio feedback for controller clicks
*
*/
void lcd_buzz(long duration, uint16_t freq) {
#if ENABLED(LCD_USE_I2C_BUZZER)
lcd.buzz(duration, freq);
#elif PIN_EXISTS(BEEPER)
buzzer.tone(duration, freq);
#else
UNUSED(duration); UNUSED(freq);
#endif
}
void lcd_quick_feedback() {
lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW;
buttons = 0;
next_button_update_ms = millis() + 500;
// Buzz and wait. The delay is needed for buttons to settle!
lcd_buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
#if ENABLED(LCD_USE_I2C_BUZZER)
delay(10);
#elif PIN_EXISTS(BEEPER)
for (int8_t i = 5; i--;) { buzzer.tick(); delay(2); }
#endif
}
/**
*
* Menu actions
*
*/
void _menu_action_back() { lcd_goto_previous_menu(); }
void menu_action_submenu(screenFunc_t func) { lcd_save_previous_menu(); lcd_goto_screen(func); }
void menu_action_gcode(const char* pgcode) { enqueue_and_echo_commands_P(pgcode); }
void menu_action_function(screenFunc_t func) { (*func)(); }
#if ENABLED(SDSUPPORT)
void menu_action_sdfile(const char* filename, char* longFilename) {
UNUSED(longFilename);
card.openAndPrintFile(filename);
lcd_return_to_status();
}
void menu_action_sddirectory(const char* filename, char* longFilename) {
UNUSED(longFilename);
card.chdir(filename);
encoderPosition = 0;
}
#endif //SDSUPPORT
void menu_action_setting_edit_bool(const char* pstr, bool* ptr) {UNUSED(pstr); *ptr = !(*ptr); }
void menu_action_setting_edit_callback_bool(const char* pstr, bool* ptr, screenFunc_t callback) {
menu_action_setting_edit_bool(pstr, ptr);
(*callback)();
}
#endif // ULTIPANEL
void lcd_init() {
lcd_implementation_init(
#if ENABLED(LCD_PROGRESS_BAR)
true
#endif
);
#if ENABLED(NEWPANEL)
#if BUTTON_EXISTS(EN1)
SET_INPUT(BTN_EN1);
WRITE(BTN_EN1, HIGH);
#endif
#if BUTTON_EXISTS(EN2)
SET_INPUT(BTN_EN2);
WRITE(BTN_EN2, HIGH);
#endif
#if BUTTON_EXISTS(ENC)
SET_INPUT(BTN_ENC);
WRITE(BTN_ENC, HIGH);
#endif
#if ENABLED(REPRAPWORLD_KEYPAD)
SET_OUTPUT(SHIFT_CLK);
OUT_WRITE(SHIFT_LD, HIGH);
SET_INPUT_PULLUP(SHIFT_OUT);
#endif
#if BUTTON_EXISTS(UP)
SET_INPUT(BTN_UP);
#endif
#if BUTTON_EXISTS(DWN)
SET_INPUT(BTN_DWN);
#endif
#if BUTTON_EXISTS(LFT)
SET_INPUT(BTN_LFT);
#endif
#if BUTTON_EXISTS(RT)
SET_INPUT(BTN_RT);
#endif
#else // !NEWPANEL
#if ENABLED(SR_LCD_2W_NL) // Non latching 2 wire shift register
SET_OUTPUT(SR_DATA_PIN);
SET_OUTPUT(SR_CLK_PIN);
#elif defined(SHIFT_CLK)
SET_OUTPUT(SHIFT_CLK);
OUT_WRITE(SHIFT_LD, HIGH);
OUT_WRITE(SHIFT_EN, LOW);
SET_INPUT_PULLUP(SHIFT_OUT);
#endif // SR_LCD_2W_NL
#endif // !NEWPANEL
#if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
SET_INPUT(SD_DETECT_PIN);
WRITE(SD_DETECT_PIN, HIGH);
lcd_sd_status = 2; // UNKNOWN
#endif
#if ENABLED(LCD_HAS_SLOW_BUTTONS)
slow_buttons = 0;
#endif
lcd_buttons_update();
#if ENABLED(ULTIPANEL)
encoderDiff = 0;
#endif
}
int lcd_strlen(const char* s) {
int i = 0, j = 0;
while (s[i]) {
#if ENABLED(MAPPER_NON)
j++;
#else
if ((s[i] & 0xC0u) != 0x80u) j++;
#endif
i++;
}
return j;
}
int lcd_strlen_P(const char* s) {
int j = 0;
while (pgm_read_byte(s)) {
#if ENABLED(MAPPER_NON)
j++;
#else
if ((pgm_read_byte(s) & 0xC0u) != 0x80u) j++;
#endif
s++;
}
return j;
}
bool lcd_blink() {
static uint8_t blink = 0;
static millis_t next_blink_ms = 0;
millis_t ms = millis();
if (ELAPSED(ms, next_blink_ms)) {
blink ^= 0xFF;
next_blink_ms = ms + 1000 - LCD_UPDATE_INTERVAL / 2;
}
return blink != 0;
}
/**
* Update the LCD, read encoder buttons, etc.
* - Read button states
* - Check the SD Card slot state
* - Act on RepRap World keypad input
* - Update the encoder position
* - Apply acceleration to the encoder position
* - Set lcdDrawUpdate = LCDVIEW_CALL_REDRAW_NOW on controller events
* - Reset the Info Screen timeout if there's any input
* - Update status indicators, if any
*
* Run the current LCD menu handler callback function:
* - Call the handler only if lcdDrawUpdate != LCDVIEW_NONE
* - Before calling the handler, LCDVIEW_CALL_NO_REDRAW => LCDVIEW_NONE
* - Call the menu handler. Menu handlers should do the following:
* - If a value changes, set lcdDrawUpdate to LCDVIEW_REDRAW_NOW and draw the value
* (Encoder events automatically set lcdDrawUpdate for you.)
* - if (lcdDrawUpdate) { redraw }
* - Before exiting the handler set lcdDrawUpdate to:
* - LCDVIEW_CLEAR_CALL_REDRAW to clear screen and set LCDVIEW_CALL_REDRAW_NEXT.
* - LCDVIEW_REDRAW_NOW or LCDVIEW_NONE to keep drawingm but only in this loop.
* - LCDVIEW_REDRAW_NEXT to keep drawing and draw on the next loop also.
* - LCDVIEW_CALL_NO_REDRAW to keep drawing (or start drawing) with no redraw on the next loop.
* - NOTE: For graphical displays menu handlers may be called 2 or more times per loop,
* so don't change lcdDrawUpdate without considering this.
*
* After the menu handler callback runs (or not):
* - Clear the LCD if lcdDrawUpdate == LCDVIEW_CLEAR_CALL_REDRAW
* - Update lcdDrawUpdate for the next loop (i.e., move one state down, usually)
*
* No worries. This function is only called from the main thread.
*/
void lcd_update() {
#if ENABLED(ULTIPANEL)
static millis_t return_to_status_ms = 0;
manage_manual_move();
lcd_buttons_update();
// If the action button is pressed...
if (LCD_CLICKED) {
if (!wait_for_unclick) { // If not waiting for a debounce release:
wait_for_unclick = true; // Set debounce flag to ignore continous clicks
lcd_clicked = !wait_for_user; // Keep the click if not waiting for a user-click
wait_for_user = false; // Any click clears wait for user
lcd_quick_feedback(); // Always make a click sound
}
}
else wait_for_unclick = false;
#endif
#if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
bool sd_status = IS_SD_INSERTED;
if (sd_status != lcd_sd_status && lcd_detected()) {
if (sd_status) {
card.initsd();
if (lcd_sd_status != 2) LCD_MESSAGEPGM(MSG_SD_INSERTED);
}
else {
card.release();
if (lcd_sd_status != 2) LCD_MESSAGEPGM(MSG_SD_REMOVED);
}
lcd_sd_status = sd_status;
lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW;
lcd_implementation_init( // to maybe revive the LCD if static electricity killed it.
#if ENABLED(LCD_PROGRESS_BAR)
currentScreen == lcd_status_screen
#endif
);
}
#endif //SDSUPPORT && SD_DETECT_PIN
millis_t ms = millis();
if (ELAPSED(ms, next_lcd_update_ms)) {
next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL;
#if ENABLED(LCD_HAS_STATUS_INDICATORS)
lcd_implementation_update_indicators();
#endif
#if ENABLED(ULTIPANEL)
#if ENABLED(LCD_HAS_SLOW_BUTTONS)
slow_buttons = lcd_implementation_read_slow_buttons(); // buttons which take too long to read in interrupt context
#endif
#if ENABLED(REPRAPWORLD_KEYPAD)
static uint8_t keypad_debounce = 0;
if (!REPRAPWORLD_KEYPAD_PRESSED) {
if (keypad_debounce > 0) keypad_debounce--;
}
else if (!keypad_debounce) {
keypad_debounce = 2;
if (REPRAPWORLD_KEYPAD_MOVE_MENU) reprapworld_keypad_move_menu();
#if DISABLED(DELTA) && Z_HOME_DIR == -1
if (REPRAPWORLD_KEYPAD_MOVE_Z_UP) reprapworld_keypad_move_z_up();
#endif
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS]) {
#if ENABLED(DELTA) || Z_HOME_DIR != -1
if (REPRAPWORLD_KEYPAD_MOVE_Z_UP) reprapworld_keypad_move_z_up();
#endif
if (REPRAPWORLD_KEYPAD_MOVE_Z_DOWN) reprapworld_keypad_move_z_down();
if (REPRAPWORLD_KEYPAD_MOVE_X_LEFT) reprapworld_keypad_move_x_left();
if (REPRAPWORLD_KEYPAD_MOVE_X_RIGHT) reprapworld_keypad_move_x_right();
if (REPRAPWORLD_KEYPAD_MOVE_Y_DOWN) reprapworld_keypad_move_y_down();
if (REPRAPWORLD_KEYPAD_MOVE_Y_UP) reprapworld_keypad_move_y_up();
}
else {
if (REPRAPWORLD_KEYPAD_MOVE_HOME) reprapworld_keypad_move_home();
}
}
#endif // REPRAPWORLD_KEYPAD
bool encoderPastThreshold = (abs(encoderDiff) >= ENCODER_PULSES_PER_STEP);
if (encoderPastThreshold || lcd_clicked) {
if (encoderPastThreshold) {
int32_t encoderMultiplier = 1;
#if ENABLED(ENCODER_RATE_MULTIPLIER)
if (encoderRateMultiplierEnabled) {
int32_t encoderMovementSteps = abs(encoderDiff) / ENCODER_PULSES_PER_STEP;
if (lastEncoderMovementMillis != 0) {
// Note that the rate is always calculated between to passes through the
// loop and that the abs of the encoderDiff value is tracked.
float encoderStepRate = (float)(encoderMovementSteps) / ((float)(ms - lastEncoderMovementMillis)) * 1000.0;
if (encoderStepRate >= ENCODER_100X_STEPS_PER_SEC) encoderMultiplier = 100;
else if (encoderStepRate >= ENCODER_10X_STEPS_PER_SEC) encoderMultiplier = 10;
#if ENABLED(ENCODER_RATE_MULTIPLIER_DEBUG)
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("Enc Step Rate: ", encoderStepRate);
SERIAL_ECHOPAIR(" Multiplier: ", encoderMultiplier);
SERIAL_ECHOPAIR(" ENCODER_10X_STEPS_PER_SEC: ", ENCODER_10X_STEPS_PER_SEC);
SERIAL_ECHOPAIR(" ENCODER_100X_STEPS_PER_SEC: ", ENCODER_100X_STEPS_PER_SEC);
SERIAL_EOL;
#endif //ENCODER_RATE_MULTIPLIER_DEBUG
}
lastEncoderMovementMillis = ms;
} // encoderRateMultiplierEnabled
#endif //ENCODER_RATE_MULTIPLIER
encoderPosition += (encoderDiff * encoderMultiplier) / ENCODER_PULSES_PER_STEP;
encoderDiff = 0;
}
return_to_status_ms = ms + LCD_TIMEOUT_TO_STATUS;
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
}
#endif // ULTIPANEL
#if ENABLED(ENSURE_SMOOTH_MOVES) && ENABLED(ALWAYS_ALLOW_MENU)
#define STATUS_UPDATE_CONDITION planner.long_move()
#else
#define STATUS_UPDATE_CONDITION true
#endif
#if ENABLED(ENSURE_SMOOTH_MOVES) && DISABLED(ALWAYS_ALLOW_MENU)
#define LCD_HANDLER_CONDITION planner.long_move()
#else
#define LCD_HANDLER_CONDITION true
#endif
// We arrive here every ~100ms when idling often enough.
// Instead of tracking the changes simply redraw the Info Screen ~1 time a second.
static int8_t lcd_status_update_delay = 1; // first update one loop delayed
if (STATUS_UPDATE_CONDITION &&
#if ENABLED(ULTIPANEL)
currentScreen == lcd_status_screen &&
#endif
!lcd_status_update_delay--
) {
lcd_status_update_delay = 9;
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
}
if (LCD_HANDLER_CONDITION) {
if (lcdDrawUpdate) {
switch (lcdDrawUpdate) {
case LCDVIEW_CALL_NO_REDRAW:
lcdDrawUpdate = LCDVIEW_NONE;
break;
case LCDVIEW_CLEAR_CALL_REDRAW: // set by handlers, then altered after (rarely occurs here)
case LCDVIEW_CALL_REDRAW_NEXT: // set by handlers, then altered after (never occurs here?)
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
case LCDVIEW_REDRAW_NOW: // set above, or by a handler through LCDVIEW_CALL_REDRAW_NEXT
case LCDVIEW_NONE:
break;
} // switch
#if ENABLED(ULTIPANEL)
#define CURRENTSCREEN() (*currentScreen)(), lcd_clicked = false
#else
#define CURRENTSCREEN() lcd_status_screen()
#endif
#if ENABLED(DOGLCD) // Changes due to different driver architecture of the DOGM display
static int8_t dot_color = 0;
dot_color = 1 - dot_color;
u8g.firstPage();
do {
lcd_setFont(FONT_MENU);
u8g.setPrintPos(125, 0);
u8g.setColorIndex(dot_color); // Set color for the alive dot
u8g.drawPixel(127, 63); // draw alive dot
u8g.setColorIndex(1); // black on white
CURRENTSCREEN();
} while (u8g.nextPage());
#else
CURRENTSCREEN();
#endif
}
#if ENABLED(ULTIPANEL)
// Return to Status Screen after a timeout
if (currentScreen == lcd_status_screen || defer_return_to_status)
return_to_status_ms = ms + LCD_TIMEOUT_TO_STATUS;
else if (ELAPSED(ms, return_to_status_ms))
lcd_return_to_status();
#endif // ULTIPANEL
switch (lcdDrawUpdate) {
case LCDVIEW_CLEAR_CALL_REDRAW:
lcd_implementation_clear();
case LCDVIEW_CALL_REDRAW_NEXT:
lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
break;
case LCDVIEW_REDRAW_NOW:
lcdDrawUpdate = LCDVIEW_NONE;
break;
case LCDVIEW_NONE:
break;
} // switch
} // LCD_HANDLER_CONDITION
}
}
void set_utf_strlen(char* s, uint8_t n) {
uint8_t i = 0, j = 0;
while (s[i] && (j < n)) {
#if ENABLED(MAPPER_NON)
j++;
#else
if ((s[i] & 0xC0u) != 0x80u) j++;
#endif
i++;
}
while (j++ < n) s[i++] = ' ';
s[i] = '\0';
}
void lcd_finishstatus(bool persist=false) {
set_utf_strlen(lcd_status_message, LCD_WIDTH);
#if !(ENABLED(LCD_PROGRESS_BAR) && (PROGRESS_MSG_EXPIRE > 0))
UNUSED(persist);
#endif
#if ENABLED(LCD_PROGRESS_BAR)
progress_bar_ms = millis();
#if PROGRESS_MSG_EXPIRE > 0
expire_status_ms = persist ? 0 : progress_bar_ms + PROGRESS_MSG_EXPIRE;
#endif
#endif
lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW;
#if ENABLED(FILAMENT_LCD_DISPLAY)
previous_lcd_status_ms = millis(); //get status message to show up for a while
#endif
}
#if ENABLED(LCD_PROGRESS_BAR) && PROGRESS_MSG_EXPIRE > 0
void dontExpireStatus() { expire_status_ms = 0; }
#endif
bool lcd_hasstatus() { return (lcd_status_message[0] != '\0'); }
void lcd_setstatus(const char* const message, bool persist) {
if (lcd_status_message_level > 0) return;
strncpy(lcd_status_message, message, 3 * (LCD_WIDTH));
lcd_finishstatus(persist);
}
void lcd_setstatuspgm(const char* const message, uint8_t level) {
if (level < lcd_status_message_level) return;
lcd_status_message_level = level;
strncpy_P(lcd_status_message, message, 3 * (LCD_WIDTH));
lcd_finishstatus(level > 0);
}
void lcd_setalertstatuspgm(const char* const message) {
lcd_setstatuspgm(message, 1);
#if ENABLED(ULTIPANEL)
lcd_return_to_status();
#endif
}
void lcd_reset_alert_level() { lcd_status_message_level = 0; }
#if HAS_LCD_CONTRAST
void set_lcd_contrast(const int value) {
lcd_contrast = constrain(value, LCD_CONTRAST_MIN, LCD_CONTRAST_MAX);
u8g.setContrast(lcd_contrast);
}
#endif
#if ENABLED(ULTIPANEL)
/**
* Setup Rotary Encoder Bit Values (for two pin encoders to indicate movement)
* These values are independent of which pins are used for EN_A and EN_B indications
* The rotary encoder part is also independent to the chipset used for the LCD
*/
#if defined(EN_A) && defined(EN_B)
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
#endif
#define GET_BUTTON_STATES(DST) \
uint8_t new_##DST = 0; \
WRITE(SHIFT_LD, LOW); \
WRITE(SHIFT_LD, HIGH); \
for (int8_t i = 0; i < 8; i++) { \
new_##DST >>= 1; \
if (READ(SHIFT_OUT)) SBI(new_##DST, 7); \
WRITE(SHIFT_CLK, HIGH); \
WRITE(SHIFT_CLK, LOW); \
} \
DST = ~new_##DST; //invert it, because a pressed switch produces a logical 0
/**
* Read encoder buttons from the hardware registers
* Warning: This function is called from interrupt context!
*/
void lcd_buttons_update() {
millis_t now = millis();
if (ELAPSED(now, next_button_update_ms)) {
#if ENABLED(NEWPANEL)
uint8_t newbutton = 0;
#if BUTTON_EXISTS(EN1)
if (BUTTON_PRESSED(EN1)) newbutton |= EN_A;
#endif
#if BUTTON_EXISTS(EN2)
if (BUTTON_PRESSED(EN2)) newbutton |= EN_B;
#endif
#if BUTTON_EXISTS(ENC)
if (BUTTON_PRESSED(ENC)) newbutton |= EN_C;
#endif
#if LCD_HAS_DIRECTIONAL_BUTTONS
// Manage directional buttons
#if ENABLED(REVERSE_MENU_DIRECTION)
#define _ENCODER_UD_STEPS (ENCODER_STEPS_PER_MENU_ITEM * encoderDirection)
#else
#define _ENCODER_UD_STEPS ENCODER_STEPS_PER_MENU_ITEM
#endif
#if ENABLED(REVERSE_ENCODER_DIRECTION)
#define ENCODER_UD_STEPS _ENCODER_UD_STEPS
#define ENCODER_LR_PULSES ENCODER_PULSES_PER_STEP
#else
#define ENCODER_UD_STEPS -(_ENCODER_UD_STEPS)
#define ENCODER_LR_PULSES -(ENCODER_PULSES_PER_STEP)
#endif
if (false) {
// for the else-ifs below
}
#if BUTTON_EXISTS(UP)
else if (BUTTON_PRESSED(UP)) {
encoderDiff = -(ENCODER_UD_STEPS);
next_button_update_ms = now + 300;
}
#endif
#if BUTTON_EXISTS(DWN)
else if (BUTTON_PRESSED(DWN)) {
encoderDiff = ENCODER_UD_STEPS;
next_button_update_ms = now + 300;
}
#endif
#if BUTTON_EXISTS(LFT)
else if (BUTTON_PRESSED(LFT)) {
encoderDiff = -(ENCODER_LR_PULSES);
next_button_update_ms = now + 300;
}
#endif
#if BUTTON_EXISTS(RT)
else if (BUTTON_PRESSED(RT)) {
encoderDiff = ENCODER_LR_PULSES;
next_button_update_ms = now + 300;
}
#endif
#endif // LCD_HAS_DIRECTIONAL_BUTTONS
buttons = newbutton;
#if ENABLED(LCD_HAS_SLOW_BUTTONS)
buttons |= slow_buttons;
#endif
#if ENABLED(REPRAPWORLD_KEYPAD)
GET_BUTTON_STATES(buttons_reprapworld_keypad);
#endif
#else
GET_BUTTON_STATES(buttons);
#endif //!NEWPANEL
} // next_button_update_ms
// Manage encoder rotation
#if ENABLED(REVERSE_MENU_DIRECTION) && ENABLED(REVERSE_ENCODER_DIRECTION)
#define ENCODER_DIFF_CW (encoderDiff -= encoderDirection)
#define ENCODER_DIFF_CCW (encoderDiff += encoderDirection)
#elif ENABLED(REVERSE_MENU_DIRECTION)
#define ENCODER_DIFF_CW (encoderDiff += encoderDirection)
#define ENCODER_DIFF_CCW (encoderDiff -= encoderDirection)
#elif ENABLED(REVERSE_ENCODER_DIRECTION)
#define ENCODER_DIFF_CW (encoderDiff--)
#define ENCODER_DIFF_CCW (encoderDiff++)
#else
#define ENCODER_DIFF_CW (encoderDiff++)
#define ENCODER_DIFF_CCW (encoderDiff--)
#endif
#define ENCODER_SPIN(_E1, _E2) switch (lastEncoderBits) { case _E1: ENCODER_DIFF_CW; break; case _E2: ENCODER_DIFF_CCW; }
uint8_t enc = 0;
if (buttons & EN_A) enc |= B01;
if (buttons & EN_B) enc |= B10;
if (enc != lastEncoderBits) {
switch (enc) {
case encrot0: ENCODER_SPIN(encrot3, encrot1); break;
case encrot1: ENCODER_SPIN(encrot0, encrot2); break;
case encrot2: ENCODER_SPIN(encrot1, encrot3); break;
case encrot3: ENCODER_SPIN(encrot2, encrot0); break;
}
}
lastEncoderBits = enc;
}
#if (ENABLED(LCD_I2C_TYPE_MCP23017) || ENABLED(LCD_I2C_TYPE_MCP23008)) && ENABLED(DETECT_DEVICE)
bool lcd_detected() { return lcd.LcdDetected() == 1; }
#endif
#endif // ULTIPANEL
#endif // ULTRA_LCD
Reference in New Issue View Git Blame Copy Permalink