mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-12-11 21:14:34 +00:00
234a9d0b12
I added in the pins into the new board files for the Azteeg X3, X3 Pro, Printrboard, and Rambo. I'm sure it can be added for others too but these are the manual specified pins. Just like many things here though, I can't test for the boards other than the Azteeg X3 Pro. Hopefully it works smoothly for everyone who happens on this nifty display. :)
112 lines
3.1 KiB
C
112 lines
3.1 KiB
C
/**
|
|
* Printrboard pin assignments (AT90USB1286)
|
|
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
|
|
* http://www.pjrc.com/teensy/teensyduino.html
|
|
* See http://reprap.org/wiki/Printrboard for more info
|
|
*/
|
|
|
|
#ifndef __AVR_AT90USB1286__
|
|
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#ifdef AT90USBxx_TEENSYPP_ASSIGNMENTS // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
|
|
#error These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h
|
|
#endif
|
|
|
|
#define AT90USB 1286 // Disable MarlinSerial etc.
|
|
|
|
#define LARGE_FLASH true
|
|
|
|
#define X_STEP_PIN 0
|
|
#define X_DIR_PIN 1
|
|
#define X_ENABLE_PIN 39
|
|
|
|
#define Y_STEP_PIN 2
|
|
#define Y_DIR_PIN 3
|
|
#define Y_ENABLE_PIN 38
|
|
|
|
#define Z_STEP_PIN 4
|
|
#define Z_DIR_PIN 5
|
|
#define Z_ENABLE_PIN 23
|
|
|
|
#define E0_STEP_PIN 6
|
|
#define E0_DIR_PIN 7
|
|
#define E0_ENABLE_PIN 19
|
|
|
|
#define HEATER_0_PIN 21 // Extruder
|
|
#define HEATER_1_PIN 46
|
|
#define HEATER_2_PIN 47
|
|
#define HEATER_BED_PIN 20
|
|
|
|
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
|
|
// fastio pin numbering otherwise
|
|
#ifdef FAN_SOFT_PWM || FAST_PWM_FAN
|
|
#define FAN_PIN 22
|
|
#else
|
|
#define FAN_PIN 16
|
|
#endif
|
|
|
|
#define X_STOP_PIN 35
|
|
#define Y_STOP_PIN 8
|
|
#define Z_STOP_PIN 36
|
|
#define TEMP_0_PIN 1 // Extruder / Analog pin numbering
|
|
#define TEMP_BED_PIN 0 // Bed / Analog pin numbering
|
|
|
|
#ifdef FILAMENT_SENSOR
|
|
#define FILWIDTH_PIN 2
|
|
#endif
|
|
|
|
#define TEMP_1_PIN -1
|
|
#define TEMP_2_PIN -1
|
|
|
|
////LCD Pin Setup////
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 8
|
|
#define LED_PIN -1
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#ifndef SDSUPPORT
|
|
// these pins are defined in the SD library if building with SD support
|
|
#define SCK_PIN 9
|
|
#define MISO_PIN 11
|
|
#define MOSI_PIN 10
|
|
#endif
|
|
|
|
#if defined(ULTRA_LCD) && defined(NEWPANEL)
|
|
//we have no buzzer installed
|
|
#define BEEPER -1
|
|
//LCD Pins
|
|
#ifdef LCD_I2C_PANELOLU2
|
|
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
|
|
#define BTN_EN2 26 //TX1 - fastio.h pin mapping 26
|
|
#define BTN_ENC 43 //A3 - fastio.h pin mapping 43
|
|
#define SDSS 40 //use SD card on Panelolu2 (Teensyduino pin mapping)
|
|
#endif // LCD_I2C_PANELOLU2
|
|
//not connected to a pin
|
|
#define SDCARDDETECT -1
|
|
#endif // ULTRA_LCD && NEWPANEL
|
|
|
|
#if defined(VIKI2) || defined(miniVIKI)
|
|
#define BEEPER 32 //FastIO
|
|
// Pins for DOGM SPI LCD Support
|
|
#define DOGLCD_A0 42 //Non-FastIO
|
|
#define DOGLCD_CS 43 //Non-FastIO
|
|
#define LCD_SCREEN_ROT_180
|
|
|
|
//The encoder and click button (FastIO Pins)
|
|
#define BTN_EN1 26
|
|
#define BTN_EN2 27
|
|
#define BTN_ENC 47 //the click switch
|
|
|
|
#define SDSS 45
|
|
#define SDCARDDETECT -1 // FastIO (Manual says 72 I'm not certain cause I can't test)
|
|
|
|
#ifdef TEMP_STAT_LEDS
|
|
#define STAT_LED_RED 12 //Non-FastIO
|
|
#define STAT_LED_BLUE 10 //Non-FastIO
|
|
#endif
|
|
#endif
|