mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-23 12:04:19 +00:00
108 lines
3.7 KiB
C
108 lines
3.7 KiB
C
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
|
|
// Licence: GPL
|
|
#include <WProgram.h>
|
|
#include "fastio.h"
|
|
extern "C" void __cxa_pure_virtual();
|
|
void __cxa_pure_virtual(){};
|
|
void get_command();
|
|
void process_commands();
|
|
|
|
void manage_inactivity(byte debug);
|
|
|
|
void manage_heater();
|
|
int temp2analogu(int celsius, const short table[][2], int numtemps);
|
|
float analog2tempu(int raw, const short table[][2], int numtemps);
|
|
#ifdef HEATER_USES_THERMISTOR
|
|
#define HEATERSOURCE 1
|
|
#endif
|
|
#ifdef BED_USES_THERMISTOR
|
|
#define BEDSOURCE 1
|
|
#endif
|
|
|
|
#define temp2analogh( c ) temp2analogu((c),temptable,NUMTEMPS)
|
|
#define analog2temp( c ) analog2tempu((c),temptable,NUMTEMPS)
|
|
|
|
#if X_ENABLE_PIN > -1
|
|
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
|
|
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
|
|
#else
|
|
#define enable_x() ;
|
|
#define disable_x() ;
|
|
#endif
|
|
#if Y_ENABLE_PIN > -1
|
|
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
|
|
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
|
|
#else
|
|
#define enable_y() ;
|
|
#define disable_y() ;
|
|
#endif
|
|
#if Z_ENABLE_PIN > -1
|
|
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
|
|
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
|
|
#else
|
|
#define enable_z() ;
|
|
#define disable_z() ;
|
|
#endif
|
|
#if E_ENABLE_PIN > -1
|
|
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
|
|
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
|
|
#else
|
|
#define enable_e() ;
|
|
#define disable_e() ;
|
|
#endif
|
|
|
|
#define X_AXIS 0
|
|
#define Y_AXIS 1
|
|
#define Z_AXIS 2
|
|
#define E_AXIS 3
|
|
|
|
void FlushSerialRequestResend();
|
|
void ClearToSend();
|
|
|
|
void get_coordinates();
|
|
void prepare_move();
|
|
void linear_move(unsigned long steps_remaining[]);
|
|
void do_step(int axis);
|
|
void kill(byte debug);
|
|
|
|
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
|
|
// the source g-code and may never actually be reached if acceleration management is active.
|
|
typedef struct {
|
|
// Fields used by the bresenham algorithm for tracing the line
|
|
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
|
|
long step_event_count; // The number of step events required to complete this block
|
|
volatile long accelerate_until; // The index of the step event on which to stop acceleration
|
|
volatile long decelerate_after; // The index of the step event on which to start decelerating
|
|
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
|
|
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
|
|
|
|
long advance_rate;
|
|
volatile long initial_advance;
|
|
volatile long final_advance;
|
|
float advance;
|
|
|
|
// Fields used by the motion planner to manage acceleration
|
|
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
|
|
float nominal_speed; // The nominal speed for this block in mm/min
|
|
float millimeters; // The total travel of this block in mm
|
|
float entry_speed;
|
|
|
|
// Settings for the trapezoid generator
|
|
long nominal_rate; // The nominal step rate for this block in step_events/sec
|
|
volatile long initial_rate; // The jerk-adjusted step rate at start of block
|
|
volatile long final_rate; // The minimal rate at exit
|
|
long acceleration; // acceleration mm/sec^2
|
|
volatile char busy;
|
|
} block_t;
|
|
|
|
void check_axes_activity();
|
|
void plan_init();
|
|
void st_init();
|
|
void tp_init();
|
|
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
|
|
void plan_set_position(float x, float y, float z, float e);
|
|
void st_wake_up();
|
|
void st_synchronize();
|
|
|
|
|