Prusa-Firmware/Firmware/timer02.c

//timer02.c
// use atmega timer2 as main system timer instead of timer0
// timer0 is used for fast pwm (OC0B output)
// original OVF handler is disabled
#include <avr/io.h>
#include <avr/interrupt.h>
#include "Arduino.h"
#include "io_atmega2560.h"

#define BEEPER              84

uint8_t timer02_pwm0 = 0;


void timer02_set_pwm0(uint8_t pwm0)
{
	TCCR0A |= (2 << COM0B0); //switch OC0B to OCR mode
	OCR0B = (uint16_t)OCR0A * pwm0 / 255;
	timer02_pwm0 = pwm0;
}

void timer02_init(void)
{
	//save sreg
	uint8_t _sreg = SREG;
	//disable interrupts for sure
	cli();
	//mask timer0 interrupts - disable all
	TIMSK0 &= ~(1<<TOIE0);
	TIMSK0 &= ~(1<<OCIE0A);
	TIMSK0 &= ~(1<<OCIE0B);
	//setup timer0
	TCCR0A = 0x00; //COM_A-B=00, WGM_0-1=00
	OCR0A = 200; //max PWM value (freq = 40kHz)
	OCR0B = 0; //current PWM value
	//switch timer0 to mode 5 (Phase Correct PWM)
	TCCR0A |= (1 << WGM00); //WGM_0-1=01
	TCCR0B = (1 << CS00) | (1 << WGM02); //WGM_2=1, CS_0-2=001 (no prescaling)
	TCCR0A |= (2 << COM0B0); //switch OC0B to OCR mode
	//setup timer2
	TCCR2A = 0x00; //COM_A-B=00, WGM_0-1=00
	TCCR2B = (4 << CS20); //WGM_2=0, CS_0-2=011
	//mask timer2 interrupts - enable OVF, disable others
	TIMSK2 |= (1<<TOIE2);
	TIMSK2 &= ~(1<<OCIE2A);
	TIMSK2 &= ~(1<<OCIE2B);
	//set timer2 OCR registers (OCRB interrupt generated 0.5ms after OVF interrupt)
	OCR2A = 0;
	OCR2B = 128;
	//restore sreg (enable interrupts)
	SREG = _sreg;
}


//following code is OVF handler for timer 2
//it is copy-paste from wiring.c and modified for timer2
//variables timer0_overflow_count and timer0_millis are declared in wiring.c



// the prescaler is set so that timer0 ticks every 64 clock cycles, and the
// the overflow handler is called every 256 ticks.
#define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(64 * 256))

// the whole number of milliseconds per timer0 overflow
#define MILLIS_INC (MICROSECONDS_PER_TIMER0_OVERFLOW / 1000)

// the fractional number of milliseconds per timer0 overflow. we shift right
// by three to fit these numbers into a byte. (for the clock speeds we care
// about - 8 and 16 MHz - this doesn't lose precision.)
#define FRACT_INC ((MICROSECONDS_PER_TIMER0_OVERFLOW % 1000) >> 3)
#define FRACT_MAX (1000 >> 3)

//extern volatile unsigned long timer0_overflow_count;
//extern volatile unsigned long timer0_millis;
//unsigned char timer0_fract = 0;
volatile unsigned long timer2_overflow_count;
volatile unsigned long timer2_millis;
unsigned char timer2_fract = 0;

ISR(TIMER2_OVF_vect)
{
	// copy these to local variables so they can be stored in registers
	// (volatile variables must be read from memory on every access)
	unsigned long m = timer2_millis;
	unsigned char f = timer2_fract;
	m += MILLIS_INC;
	f += FRACT_INC;
	if (f >= FRACT_MAX)
	{
		f -= FRACT_MAX;
		m += 1;
	}
	timer2_fract = f;
	timer2_millis = m;
	timer2_overflow_count++;
}

unsigned long millis2(void)
{
	unsigned long m;
	uint8_t oldSREG = SREG;

	// disable interrupts while we read timer0_millis or we might get an
	// inconsistent value (e.g. in the middle of a write to timer0_millis)
	cli();
	m = timer2_millis;
	SREG = oldSREG;

	return m;
}

unsigned long micros2(void)
{
	unsigned long m;
	uint8_t oldSREG = SREG, t;
	cli();
	m = timer2_overflow_count;
#if defined(TCNT2)
	t = TCNT2;
#elif defined(TCNT2L)
	t = TCNT2L;
#else
	#error TIMER 2 not defined
#endif
#ifdef TIFR2
	if ((TIFR2 & _BV(TOV2)) && (t < 255))
		m++;
#else
	if ((TIFR & _BV(TOV2)) && (t < 255))
		m++;
#endif
	SREG = oldSREG;	
	return ((m << 8) + t) * (64 / clockCyclesPerMicrosecond());
}

void delay2(unsigned long ms)
{
	uint32_t start = micros2();
	while (ms > 0)
	{
		yield();
		while ( ms > 0 && (micros2() - start) >= 1000)
		{
			ms--;
			start += 1000;
		}
	}
}

void tone2(__attribute__((unused)) uint8_t _pin, __attribute__((unused)) unsigned int frequency/*, unsigned long duration*/)
{
	PIN_SET(BEEPER);
}

void noTone2(__attribute__((unused)) uint8_t _pin)
{
	PIN_CLR(BEEPER);
}