Prusa-Firmware/lang_upgrade/msgs_en_used_more.txt

MSG_ALL c=19 r=1 "All"
MSG_AUTO_HOME c=0 r=0 "Auto home"
MSG_AUTO_MODE_ON c=0 r=0 "Mode [auto power]"
MSG_BABYSTEP_Z c=0 r=0 "Live adjust Z"
MSG_BABYSTEP_Z_NOT_SET c=20 r=12 "Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."
MSG_BED c=0 r=0 "Bed"
MSG_BED_DONE c=0 r=0 "Bed done"
MSG_BED_HEATING c=0 r=0 "Bed Heating"
MSG_BED_LEVELING_FAILED_POINT_LOW c=20 r=4 "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED c=20 r=8 "XYZ calibration failed. Please consult the manual."
MSG_CALIBRATE_Z_AUTO c=20 r=2 "Calibrating Z"
MSG_CARD_MENU c=0 r=0 "Print from SD"
MSG_CONFIRM_NOZZLE_CLEAN c=20 r=8 "Please clean the nozzle for calibration. Click when done."
MSG_COOLDOWN c=0 r=0 "Cooldown"
MSG_CRASH_DETECTED c=20 r=1 "Crash detected."
MSG_CRASHDETECT_NA c=0 r=0 "Crash det.  [N/A]"
MSG_CRASHDETECT_OFF c=0 r=0 "Crash det.  [off]"
MSG_CRASHDETECT_ON c=0 r=0 "Crash det.   [on]"
MSG_ENDSTOP_HIT c=0 r=0 "TRIGGERED"
MSG_ENDSTOP_OPEN c=0 r=0 "open"
MSG_ENDSTOPS_HIT c=0 r=0 "endstops hit: "
MSG_Enqueing c=0 r=0 "enqueing \""
MSG_ERR_STOPPED c=0 r=0 "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
MSG_ERROR c=0 r=0 "ERROR:"
MSG_EXTRUDER c=17 r=1 "Extruder"
MSG_FAN_SPEED c=14 r=0 "Fan speed"
MSG_FILAMENT_CLEAN c=20 r=2 "Filament extruding & with correct color?"
MSG_FILAMENT_LOADING_T0 c=20 r=4 "Insert filament into extruder 1. Click when done."
MSG_FILAMENT_LOADING_T1 c=20 r=4 "Insert filament into extruder 2. Click when done."
MSG_FILAMENT_LOADING_T2 c=20 r=4 "Insert filament into extruder 3. Click when done."
MSG_FILAMENT_LOADING_T3 c=20 r=4 "Insert filament into extruder 4. Click when done."
MSG_FILAMENTCHANGE c=0 r=0 "Change filament"
MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 c=60 r=0 "Searching bed calibration point"
MSG_FIND_BED_OFFSET_AND_SKEW_LINE2 c=14 r=0 " of 4"
MSG_FINISHING_MOVEMENTS c=20 r=1 "Finishing movements"
MSG_FOLLOW_CALIBRATION_FLOW c=20 r=8 "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
MSG_FSENS_AUTOLOAD_NA c=17 r=1 "F. autoload [N/A]"
MSG_FSENSOR_OFF c=0 r=0 "Fil. sensor [off]"
MSG_FSENSOR_ON c=0 r=0 "Fil. sensor  [on]"
MSG_HEATING c=0 r=0 "Heating"
MSG_HEATING_COMPLETE c=20 r=0 "Heating done."
MSG_HOMEYZ c=0 r=0 "Calibrate Z"
MSG_CHOOSE_EXTRUDER c=20 r=1 "Choose extruder:"
MSG_LOAD_FILAMENT c=17 r=0 "Load filament"
MSG_LOADING_FILAMENT c=20 r=0 "Loading filament"
MSG_M117_V2_CALIBRATION c=25 r=1 "M117 First layer cal."
MSG_MAIN c=0 r=0 "Main"
MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60 r=0 "Measuring reference height of calibration point"
MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14 r=0 " of 9"
MSG_MENU_CALIBRATION c=0 r=0 "Calibration"
MSG_NO c=0 r=0 "No"
MSG_NOZZLE c=0 r=0 "Nozzle"
MSG_OK c=0 r=0 "ok"
MSG_PAPER c=20 r=8 "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
MSG_PLACE_STEEL_SHEET c=20 r=4 "Please place steel sheet on heatbed."
MSG_PLEASE_WAIT c=20 r=0 "Please wait"
MSG_POWERUP c=0 r=0 "PowerUp"
MSG_PREHEAT_NOZZLE c=20 r=0 "Preheat the nozzle!"
MSG_PRESS_TO_UNLOAD c=20 r=4 "Please press the knob to unload filament"
MSG_PRINT_ABORTED c=20 r=0 "Print aborted"
MSG_PULL_OUT_FILAMENT c=20 r=4 "Please pull out filament immediately"
MSG_RECOVER_PRINT c=20 r=2 "Blackout occurred. Recover print?"
MSG_REFRESH c=0 r=0 "\xF8" "Refresh"
MSG_REMOVE_STEEL_SHEET c=20 r=4 "Please remove steel sheet from heatbed."
MSG_SD_ERR_WRITE_TO_FILE c=0 r=0 "error writing to file"
MSG_SD_OPEN_FILE_FAIL c=0 r=0 "open failed, File: "
MSG_SD_WORKDIR_FAIL c=0 r=0 "workDir open failed"
MSG_SELFTEST_COOLING_FAN c=20 r=0 "Front print fan?"
MSG_SELFTEST_EXTRUDER_FAN c=20 r=0 "Left hotend fan?"
MSG_SELFTEST_FAILED c=20 r=0 "Selftest failed  "
MSG_SELFTEST_FAN c=20 r=0 "Fan test"
MSG_SELFTEST_FAN_NO c=19 r=0 "Not spinning"
MSG_SELFTEST_FAN_YES c=19 r=0 "Spinning"
MSG_SELFTEST_CHECK_BED c=20 r=0 "Checking bed     "
MSG_SELFTEST_CHECK_FSENSOR c=20 r=0 "Checking sensors "
MSG_SELFTEST_MOTOR c=0 r=0 "Motor"
MSG_SELFTEST_WIRINGERROR c=0 r=0 "Wiring error"
MSG_SETTINGS c=0 r=0 "Settings"
MSG_SILENT_MODE_OFF c=0 r=0 "Mode [high power]" 
MSG_SILENT_MODE_ON c=0 r=0 "Mode     [silent]"
MSG_STEALTH_MODE_OFF c=0 r=0 "Mode     [Normal]"
MSG_STEALTH_MODE_ON c=0 r=0 "Mode    [Stealth]"
MSG_STEEL_SHEET_CHECK c=20 r=2 "Is steel sheet on heatbed?"
MSG_STOP_PRINT c=0 r=0 "Stop print"
MSG_STOPPED c=0 r=0 "STOPPED. "
MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal.          "
MSG_TEMP_CALIBRATION_DONE c=20 r=12 "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
MSG_UNLOAD_FILAMENT c=17 r=0 "Unload filament"
MSG_UNLOADING_FILAMENT c=20 r=1 "Unloading filament"
MSG_WATCH c=0 r=0 "Info screen"
MSG_WIZARD_CALIBRATION_FAILED c=20 r=8 "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
MSG_WIZARD_DONE c=20 r=8 "All is done. Happy printing!"
MSG_WIZARD_HEATING c=20 r=3 "Preheating nozzle. Please wait."
MSG_WIZARD_QUIT c=20 r=8 "You can always resume the Wizard from Calibration -> Wizard."
MSG_YES c=0 r=0 "Yes"
WELCOME_MSG c=20 r=0 CUSTOM_MENDEL_NAME " ready."