Merge pull request #2274 from wavexx/fix_mesh_plan_buffer_line
PFW-1028: Fix recovery from filament sensor checks / crash detect / power panic
This commit is contained in:
DRracer
GitHub
commit
15bfb7013d
@ -296,6 +296,7 @@ void setPwmFrequency(uint8_t pin, int val);
|
||||
extern bool fans_check_enabled;
|
||||
extern float homing_feedrate[];
|
||||
extern bool axis_relative_modes[];
|
||||
extern float feedrate;
|
||||
extern int feedmultiply;
|
||||
extern int extrudemultiply; // Sets extrude multiply factor (in percent) for all extruders
|
||||
extern int extruder_multiply[EXTRUDERS]; // sets extrude multiply factor (in percent) for each extruder individually
|
||||
@ -395,7 +396,7 @@ extern uint16_t gcode_in_progress;
|
||||
extern LongTimer safetyTimer;
|
||||
|
||||
#define PRINT_PERCENT_DONE_INIT 0xff
|
||||
#define PRINTER_ACTIVE (IS_SD_PRINTING || is_usb_printing || isPrintPaused || (custom_message_type == CustomMsg::TempCal) || saved_printing || (lcd_commands_type == LcdCommands::Layer1Cal) || card.paused || mmu_print_saved)
|
||||
#define PRINTER_ACTIVE (IS_SD_PRINTING || is_usb_printing || isPrintPaused || (custom_message_type == CustomMsg::TempCal) || saved_printing || (lcd_commands_type == LcdCommands::Layer1Cal) || mmu_print_saved)
|
||||
|
||||
//! Beware - mcode_in_progress is set as soon as the command gets really processed,
|
||||
//! which is not the same as posting the M600 command into the command queue
|
||||
|
||||
@ -309,6 +309,8 @@ bool no_response = false;
|
||||
uint8_t important_status;
|
||||
uint8_t saved_filament_type;
|
||||
|
||||
#define SAVED_TARGET_UNSET (X_MIN_POS-1)
|
||||
float saved_target[NUM_AXIS] = {SAVED_TARGET_UNSET, 0, 0, 0};
|
||||
|
||||
// save/restore printing in case that mmu was not responding
|
||||
bool mmu_print_saved = false;
|
||||
@ -329,7 +331,15 @@ float destination[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0};
|
||||
|
||||
// For tracing an arc
|
||||
static float offset[3] = {0.0, 0.0, 0.0};
|
||||
static float feedrate = 1500.0, next_feedrate, saved_feedrate;
|
||||
|
||||
// Current feedrate
|
||||
float feedrate = 1500.0;
|
||||
|
||||
// Feedrate for the next move
|
||||
static float next_feedrate;
|
||||
|
||||
// Original feedrate saved during homing moves
|
||||
static float saved_feedrate;
|
||||
|
||||
// Determines Absolute or Relative Coordinates.
|
||||
// Also there is bool axis_relative_modes[] per axis flag.
|
||||
@ -373,8 +383,8 @@ bool saved_printing = false; //!< Print is paused and saved in RAM
|
||||
static uint32_t saved_sdpos = 0; //!< SD card position, or line number in case of USB printing
|
||||
uint8_t saved_printing_type = PRINTING_TYPE_SD;
|
||||
static float saved_pos[4] = { 0, 0, 0, 0 };
|
||||
//! Feedrate hopefully derived from an active block of the planner at the time the print has been canceled, in mm/min.
|
||||
static float saved_feedrate2 = 0;
|
||||
static uint16_t saved_feedrate2 = 0; //!< Default feedrate (truncated from float)
|
||||
static int saved_feedmultiply2 = 0;
|
||||
static uint8_t saved_active_extruder = 0;
|
||||
static float saved_extruder_temperature = 0.0; //!< Active extruder temperature
|
||||
static bool saved_extruder_under_pressure = false;
|
||||
@ -3655,7 +3665,7 @@ void process_commands()
|
||||
|
||||
Set of internal PRUSA commands
|
||||
|
||||
PRUSA [ Ping | PRN | FAN | fn | thx | uvlo | fsensor_recover | MMURES | RESET | fv | M28 | SN | Fir | Rev | Lang | Lz | Beat | FR ]
|
||||
PRUSA [ Ping | PRN | FAN | fn | thx | uvlo | MMURES | RESET | fv | M28 | SN | Fir | Rev | Lang | Lz | Beat | FR ]
|
||||
|
||||
- `Ping`
|
||||
- `PRN` - Prints revision of the printer
|
||||
@ -3663,7 +3673,6 @@ void process_commands()
|
||||
- `fn` - Prints farm no.
|
||||
- `thx`
|
||||
- `uvlo`
|
||||
- `fsensor_recover` - Filament sensor recover - restore print and continue
|
||||
- `MMURES` - Reset MMU
|
||||
- `RESET` - (Careful!)
|
||||
- `fv` - ?
|
||||
@ -3713,12 +3722,6 @@ void process_commands()
|
||||
eeprom_update_byte((uint8_t*)EEPROM_UVLO,0);
|
||||
enquecommand_P(PSTR("M24"));
|
||||
}
|
||||
#ifdef FILAMENT_SENSOR
|
||||
else if (code_seen("fsensor_recover")) // PRUSA fsensor_recover
|
||||
{
|
||||
fsensor_restore_print_and_continue();
|
||||
}
|
||||
#endif //FILAMENT_SENSOR
|
||||
else if (code_seen("MMURES")) // PRUSA MMURES
|
||||
{
|
||||
mmu_reset();
|
||||
@ -4043,8 +4046,19 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
|
||||
|
||||
#endif
|
||||
|
||||
get_coordinates(); // For X Y Z E F
|
||||
|
||||
// When recovering from a previous print move, restore the originally
|
||||
// calculated target position on the first USB/SD command. This accounts
|
||||
// properly for relative moves
|
||||
if ((saved_target[0] != SAVED_TARGET_UNSET) &&
|
||||
((CMDBUFFER_CURRENT_TYPE == CMDBUFFER_CURRENT_TYPE_SDCARD) ||
|
||||
(CMDBUFFER_CURRENT_TYPE == CMDBUFFER_CURRENT_TYPE_USB_WITH_LINENR)))
|
||||
{
|
||||
memcpy(destination, saved_target, sizeof(destination));
|
||||
saved_target[0] = SAVED_TARGET_UNSET;
|
||||
}
|
||||
|
||||
get_coordinates(); // For X Y Z E F
|
||||
if (total_filament_used > ((current_position[E_AXIS] - destination[E_AXIS]) * 100)) { //protection against total_filament_used overflow
|
||||
total_filament_used = total_filament_used + ((destination[E_AXIS] - current_position[E_AXIS]) * 100);
|
||||
}
|
||||
@ -5363,21 +5377,19 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
|
||||
card.openFile(strchr_pointer + 4,true);
|
||||
break;
|
||||
|
||||
//! ### M24 - Start SD print
|
||||
//! ### M24 - Start/resume SD print
|
||||
// ----------------------------------
|
||||
case 24:
|
||||
if (!card.paused)
|
||||
failstats_reset_print();
|
||||
card.startFileprint();
|
||||
starttime=_millis();
|
||||
if (isPrintPaused)
|
||||
lcd_resume_print();
|
||||
else
|
||||
{
|
||||
failstats_reset_print();
|
||||
card.startFileprint();
|
||||
starttime=_millis();
|
||||
}
|
||||
break;
|
||||
|
||||
//! ### M25 - Pause SD print
|
||||
// ----------------------------------
|
||||
case 25:
|
||||
card.pauseSDPrint();
|
||||
break;
|
||||
|
||||
//! ### M26 S\<index\> - Set SD index
|
||||
//! Set position in SD card file to index in bytes.
|
||||
//! This command is expected to be called after M23 and before M24.
|
||||
@ -7232,26 +7244,34 @@ Sigma_Exit:
|
||||
break;
|
||||
#endif //FILAMENTCHANGEENABLE
|
||||
|
||||
//! ### M25 - Pause SD print
|
||||
//! ### M601 - Pause print
|
||||
//! ### M125 - Pause print (TODO: not implemented)
|
||||
// -------------------------------
|
||||
case 25:
|
||||
case 601:
|
||||
{
|
||||
cmdqueue_pop_front(); //trick because we want skip this command (M601) after restore
|
||||
lcd_pause_print();
|
||||
if (!isPrintPaused)
|
||||
{
|
||||
st_synchronize();
|
||||
cmdqueue_pop_front(); //trick because we want skip this command (M601) after restore
|
||||
lcd_pause_print();
|
||||
}
|
||||
}
|
||||
break;
|
||||
|
||||
//! ### M602 - Resume print
|
||||
// -------------------------------
|
||||
case 602: {
|
||||
lcd_resume_print();
|
||||
if (isPrintPaused)
|
||||
lcd_resume_print();
|
||||
}
|
||||
break;
|
||||
|
||||
//! ### M603 - Stop print
|
||||
// -------------------------------
|
||||
case 603: {
|
||||
lcd_print_stop();
|
||||
Stop();
|
||||
}
|
||||
break;
|
||||
|
||||
@ -8339,10 +8359,9 @@ void clamp_to_software_endstops(float target[3])
|
||||
}
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
void mesh_plan_buffer_line(const float &x, const float &y, const float &z, const float &e, const float &feed_rate, const uint8_t extruder) {
|
||||
void mesh_plan_buffer_line(const float &x, const float &y, const float &z, const float &e, const float &feed_rate, const uint8_t extruder) {
|
||||
float dx = x - current_position[X_AXIS];
|
||||
float dy = y - current_position[Y_AXIS];
|
||||
float dz = z - current_position[Z_AXIS];
|
||||
int n_segments = 0;
|
||||
|
||||
if (mbl.active) {
|
||||
@ -8353,24 +8372,30 @@ void clamp_to_software_endstops(float target[3])
|
||||
}
|
||||
|
||||
if (n_segments > 1) {
|
||||
// In a multi-segment move explicitly set the final target in the plan
|
||||
// as the move will be recalculated in it's entirety
|
||||
float gcode_target[NUM_AXIS];
|
||||
gcode_target[X_AXIS] = x;
|
||||
gcode_target[Y_AXIS] = y;
|
||||
gcode_target[Z_AXIS] = z;
|
||||
gcode_target[E_AXIS] = e;
|
||||
|
||||
float dz = z - current_position[Z_AXIS];
|
||||
float de = e - current_position[E_AXIS];
|
||||
|
||||
for (int i = 1; i < n_segments; ++ i) {
|
||||
float t = float(i) / float(n_segments);
|
||||
if (saved_printing || (mbl.active == false)) return;
|
||||
plan_buffer_line(
|
||||
current_position[X_AXIS] + t * dx,
|
||||
plan_buffer_line(current_position[X_AXIS] + t * dx,
|
||||
current_position[Y_AXIS] + t * dy,
|
||||
current_position[Z_AXIS] + t * dz,
|
||||
current_position[E_AXIS] + t * de,
|
||||
feed_rate, extruder);
|
||||
feed_rate, extruder, gcode_target);
|
||||
if (waiting_inside_plan_buffer_line_print_aborted)
|
||||
return;
|
||||
}
|
||||
}
|
||||
// The rest of the path.
|
||||
plan_buffer_line(x, y, z, e, feed_rate, extruder);
|
||||
current_position[X_AXIS] = x;
|
||||
current_position[Y_AXIS] = y;
|
||||
current_position[Z_AXIS] = z;
|
||||
current_position[E_AXIS] = e;
|
||||
}
|
||||
#endif // MESH_BED_LEVELING
|
||||
|
||||
@ -8390,10 +8415,10 @@ void prepare_move()
|
||||
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate*feedmultiply*(1./(60.f*100.f)), active_extruder);
|
||||
#endif
|
||||
}
|
||||
if (waiting_inside_plan_buffer_line_print_aborted)
|
||||
return;
|
||||
|
||||
for(int8_t i=0; i < NUM_AXIS; i++) {
|
||||
current_position[i] = destination[i];
|
||||
}
|
||||
set_current_to_destination();
|
||||
}
|
||||
|
||||
void prepare_arc_move(char isclockwise) {
|
||||
@ -9114,10 +9139,8 @@ void bed_check(float x_dimension, float y_dimension, int x_points_num, int y_poi
|
||||
destination[X_AXIS] = ix * (x_dimension / (x_points_num - 1)) + shift_x;
|
||||
destination[Y_AXIS] = iy * (y_dimension / (y_points_num - 1)) + shift_y;
|
||||
|
||||
mesh_plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], XY_AXIS_FEEDRATE/6, active_extruder);
|
||||
for(int8_t i=0; i < NUM_AXIS; i++) {
|
||||
current_position[i] = destination[i];
|
||||
}
|
||||
mesh_plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], XY_AXIS_FEEDRATE/6, active_extruder);
|
||||
set_current_to_destination();
|
||||
st_synchronize();
|
||||
|
||||
// printf_P(PSTR("X = %f; Y= %f \n"), current_position[X_AXIS], current_position[Y_AXIS]);
|
||||
@ -9603,8 +9626,18 @@ void uvlo_()
|
||||
if (sd_position < 0) sd_position = 0;
|
||||
}
|
||||
|
||||
// Backup the feedrate in mm/min.
|
||||
int feedrate_bckp = blocks_queued() ? (block_buffer[block_buffer_tail].nominal_speed * 60.f) : feedrate;
|
||||
// save the global state at planning time
|
||||
uint16_t feedrate_bckp;
|
||||
if (blocks_queued())
|
||||
{
|
||||
memcpy(saved_target, current_block->gcode_target, sizeof(saved_target));
|
||||
feedrate_bckp = current_block->gcode_feedrate;
|
||||
}
|
||||
else
|
||||
{
|
||||
saved_target[0] = SAVED_TARGET_UNSET;
|
||||
feedrate_bckp = feedrate;
|
||||
}
|
||||
|
||||
// After this call, the planner queue is emptied and the current_position is set to a current logical coordinate.
|
||||
// The logical coordinate will likely differ from the machine coordinate if the skew calibration and mesh bed leveling
|
||||
@ -9671,7 +9704,8 @@ void uvlo_()
|
||||
eeprom_update_float((float*)(EEPROM_UVLO_CURRENT_POSITION + 4), current_position[Y_AXIS]);
|
||||
eeprom_update_float((float*)EEPROM_UVLO_CURRENT_POSITION_Z , current_position[Z_AXIS]);
|
||||
// Store the current feed rate, temperatures, fan speed and extruder multipliers (flow rates)
|
||||
EEPROM_save_B(EEPROM_UVLO_FEEDRATE, &feedrate_bckp);
|
||||
eeprom_update_word((uint16_t*)EEPROM_UVLO_FEEDRATE, feedrate_bckp);
|
||||
EEPROM_save_B(EEPROM_UVLO_FEEDMULTIPLY, &feedmultiply);
|
||||
eeprom_update_byte((uint8_t*)EEPROM_UVLO_TARGET_HOTEND, target_temperature[active_extruder]);
|
||||
eeprom_update_byte((uint8_t*)EEPROM_UVLO_TARGET_BED, target_temperature_bed);
|
||||
eeprom_update_byte((uint8_t*)EEPROM_UVLO_FAN_SPEED, fanSpeed);
|
||||
@ -9683,6 +9717,11 @@ void uvlo_()
|
||||
#endif
|
||||
#endif
|
||||
eeprom_update_word((uint16_t*)(EEPROM_EXTRUDEMULTIPLY), (uint16_t)extrudemultiply);
|
||||
// Store the saved target
|
||||
eeprom_update_float((float*)(EEPROM_UVLO_SAVED_TARGET+0*4), saved_target[X_AXIS]);
|
||||
eeprom_update_float((float*)(EEPROM_UVLO_SAVED_TARGET+1*4), saved_target[Y_AXIS]);
|
||||
eeprom_update_float((float*)(EEPROM_UVLO_SAVED_TARGET+2*4), saved_target[Z_AXIS]);
|
||||
eeprom_update_float((float*)(EEPROM_UVLO_SAVED_TARGET+3*4), saved_target[E_AXIS]);
|
||||
|
||||
// Finaly store the "power outage" flag.
|
||||
if(sd_print) eeprom_update_byte((uint8_t*)EEPROM_UVLO, 1);
|
||||
@ -9931,10 +9970,17 @@ void recover_machine_state_after_power_panic(bool bTiny)
|
||||
#endif
|
||||
#endif
|
||||
extrudemultiply = (int)eeprom_read_word((uint16_t*)(EEPROM_EXTRUDEMULTIPLY));
|
||||
|
||||
// 9) Recover the saved target
|
||||
saved_target[X_AXIS] = eeprom_read_float((float*)(EEPROM_UVLO_SAVED_TARGET+0*4));
|
||||
saved_target[Y_AXIS] = eeprom_read_float((float*)(EEPROM_UVLO_SAVED_TARGET+1*4));
|
||||
saved_target[Z_AXIS] = eeprom_read_float((float*)(EEPROM_UVLO_SAVED_TARGET+2*4));
|
||||
saved_target[E_AXIS] = eeprom_read_float((float*)(EEPROM_UVLO_SAVED_TARGET+3*4));
|
||||
}
|
||||
|
||||
void restore_print_from_eeprom() {
|
||||
int feedrate_rec;
|
||||
int feedmultiply_rec;
|
||||
uint8_t fan_speed_rec;
|
||||
char cmd[30];
|
||||
char filename[13];
|
||||
@ -9942,9 +9988,12 @@ void restore_print_from_eeprom() {
|
||||
char dir_name[9];
|
||||
|
||||
fan_speed_rec = eeprom_read_byte((uint8_t*)EEPROM_UVLO_FAN_SPEED);
|
||||
EEPROM_read_B(EEPROM_UVLO_FEEDRATE, &feedrate_rec);
|
||||
feedrate_rec = eeprom_read_word((uint16_t*)EEPROM_UVLO_FEEDRATE);
|
||||
EEPROM_read_B(EEPROM_UVLO_FEEDMULTIPLY, &feedmultiply_rec);
|
||||
SERIAL_ECHOPGM("Feedrate:");
|
||||
MYSERIAL.println(feedrate_rec);
|
||||
MYSERIAL.print(feedrate_rec);
|
||||
SERIAL_ECHOPGM(", feedmultiply:");
|
||||
MYSERIAL.println(feedmultiply_rec);
|
||||
|
||||
depth = eeprom_read_byte((uint8_t*)EEPROM_DIR_DEPTH);
|
||||
|
||||
@ -9985,9 +10034,11 @@ void restore_print_from_eeprom() {
|
||||
enquecommand(cmd);
|
||||
// Unretract.
|
||||
enquecommand_P(PSTR("G1 E" STRINGIFY(2*default_retraction)" F480"));
|
||||
// Set the feedrate saved at the power panic.
|
||||
// Set the feedrates saved at the power panic.
|
||||
sprintf_P(cmd, PSTR("G1 F%d"), feedrate_rec);
|
||||
enquecommand(cmd);
|
||||
sprintf_P(cmd, PSTR("M220 S%d"), feedmultiply_rec);
|
||||
enquecommand(cmd);
|
||||
if (eeprom_read_byte((uint8_t*)EEPROM_UVLO_E_ABS))
|
||||
{
|
||||
enquecommand_P(PSTR("M82")); //E axis abslute mode
|
||||
@ -10139,16 +10190,21 @@ void stop_and_save_print_to_ram(float z_move, float e_move)
|
||||
}
|
||||
#endif
|
||||
|
||||
#if 0
|
||||
saved_feedrate2 = feedrate; //save feedrate
|
||||
#else
|
||||
// Try to deduce the feedrate from the first block of the planner.
|
||||
// Speed is in mm/min.
|
||||
saved_feedrate2 = blocks_queued() ? (block_buffer[block_buffer_tail].nominal_speed * 60.f) : feedrate;
|
||||
#endif
|
||||
// save the global state at planning time
|
||||
if (blocks_queued())
|
||||
{
|
||||
memcpy(saved_target, current_block->gcode_target, sizeof(saved_target));
|
||||
saved_feedrate2 = current_block->gcode_feedrate;
|
||||
}
|
||||
else
|
||||
{
|
||||
saved_target[0] = SAVED_TARGET_UNSET;
|
||||
saved_feedrate2 = feedrate;
|
||||
}
|
||||
|
||||
planner_abort_hard(); //abort printing
|
||||
memcpy(saved_pos, current_position, sizeof(saved_pos));
|
||||
saved_feedmultiply2 = feedmultiply; //save feedmultiply
|
||||
saved_active_extruder = active_extruder; //save active_extruder
|
||||
saved_extruder_temperature = degTargetHotend(active_extruder);
|
||||
|
||||
@ -10226,7 +10282,6 @@ void restore_print_from_ram_and_continue(float e_move)
|
||||
wait_for_heater(_millis(), saved_active_extruder);
|
||||
heating_status = 2;
|
||||
}
|
||||
feedrate = saved_feedrate2; //restore feedrate
|
||||
axis_relative_modes[E_AXIS] = saved_extruder_relative_mode;
|
||||
float e = saved_pos[E_AXIS] - e_move;
|
||||
plan_set_e_position(e);
|
||||
@ -10249,6 +10304,10 @@ void restore_print_from_ram_and_continue(float e_move)
|
||||
fans_check_enabled = true;
|
||||
#endif
|
||||
|
||||
// restore original feedrate/feedmultiply _after_ restoring the extruder position
|
||||
feedrate = saved_feedrate2;
|
||||
feedmultiply = saved_feedmultiply2;
|
||||
|
||||
memcpy(current_position, saved_pos, sizeof(saved_pos));
|
||||
memcpy(destination, current_position, sizeof(destination));
|
||||
if (saved_printing_type == PRINTING_TYPE_SD) { //was sd printing
|
||||
@ -10264,10 +10323,12 @@ void restore_print_from_ram_and_continue(float e_move)
|
||||
else {
|
||||
//not sd printing nor usb printing
|
||||
}
|
||||
|
||||
SERIAL_PROTOCOLLNRPGM(MSG_OK); //dummy response because of octoprint is waiting for this
|
||||
lcd_setstatuspgm(_T(WELCOME_MSG));
|
||||
saved_printing_type = PRINTING_TYPE_NONE;
|
||||
saved_printing = false;
|
||||
waiting_inside_plan_buffer_line_print_aborted = true; //unroll the stack
|
||||
}
|
||||
|
||||
void print_world_coordinates()
|
||||
|
||||
@ -25,7 +25,6 @@ CardReader::CardReader()
|
||||
sdpos = 0;
|
||||
sdprinting = false;
|
||||
cardOK = false;
|
||||
paused = false;
|
||||
saving = false;
|
||||
logging = false;
|
||||
autostart_atmillis=0;
|
||||
@ -242,24 +241,13 @@ void CardReader::startFileprint()
|
||||
if(cardOK)
|
||||
{
|
||||
sdprinting = true;
|
||||
paused = false;
|
||||
Stopped = false;
|
||||
Stopped = false;
|
||||
#ifdef SDCARD_SORT_ALPHA
|
||||
//flush_presort();
|
||||
#endif
|
||||
}
|
||||
}
|
||||
|
||||
void CardReader::pauseSDPrint()
|
||||
{
|
||||
if(sdprinting)
|
||||
{
|
||||
sdprinting = false;
|
||||
paused = true;
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
void CardReader::openLogFile(const char* name)
|
||||
{
|
||||
logging = true;
|
||||
@ -408,8 +396,6 @@ void CardReader::openFile(const char* name,bool read, bool replace_current/*=tru
|
||||
SERIAL_ECHOLN(name);
|
||||
}
|
||||
sdprinting = false;
|
||||
paused = false;
|
||||
|
||||
|
||||
SdFile myDir;
|
||||
const char *fname=name;
|
||||
@ -492,24 +478,27 @@ uint32_t CardReader::getFileSize()
|
||||
|
||||
void CardReader::getStatus()
|
||||
{
|
||||
if(sdprinting){
|
||||
SERIAL_PROTOCOL(longFilename);
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
SERIAL_PROTOCOLRPGM(_N("SD printing byte "));////MSG_SD_PRINTING_BYTE
|
||||
SERIAL_PROTOCOL(sdpos);
|
||||
SERIAL_PROTOCOLPGM("/");
|
||||
SERIAL_PROTOCOLLN(filesize);
|
||||
uint16_t time = _millis()/60000 - starttime/60000;
|
||||
SERIAL_PROTOCOL(itostr2(time/60));
|
||||
SERIAL_PROTOCOL(':');
|
||||
SERIAL_PROTOCOL(itostr2(time%60));
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
}
|
||||
else if (paused) {
|
||||
SERIAL_PROTOCOLLNPGM("SD print paused");
|
||||
}
|
||||
else if (saved_printing) {
|
||||
SERIAL_PROTOCOLLNPGM("Print saved");
|
||||
if(sdprinting)
|
||||
{
|
||||
if (isPrintPaused) {
|
||||
SERIAL_PROTOCOLLNPGM("SD print paused");
|
||||
}
|
||||
else if (saved_printing) {
|
||||
SERIAL_PROTOCOLLNPGM("Print saved");
|
||||
}
|
||||
else {
|
||||
SERIAL_PROTOCOL(longFilename);
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
SERIAL_PROTOCOLRPGM(_N("SD printing byte "));////MSG_SD_PRINTING_BYTE
|
||||
SERIAL_PROTOCOL(sdpos);
|
||||
SERIAL_PROTOCOLPGM("/");
|
||||
SERIAL_PROTOCOLLN(filesize);
|
||||
uint16_t time = _millis()/60000 - starttime/60000;
|
||||
SERIAL_PROTOCOL(itostr2(time/60));
|
||||
SERIAL_PROTOCOL(':');
|
||||
SERIAL_PROTOCOL(itostr2(time%60));
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
}
|
||||
}
|
||||
else {
|
||||
SERIAL_PROTOCOLLNPGM("Not SD printing");
|
||||
|
||||
@ -25,7 +25,6 @@ public:
|
||||
void closefile(bool store_location=false);
|
||||
void release();
|
||||
void startFileprint();
|
||||
void pauseSDPrint();
|
||||
uint32_t getFileSize();
|
||||
void getStatus();
|
||||
void printingHasFinished();
|
||||
@ -75,7 +74,6 @@ public:
|
||||
bool logging;
|
||||
bool sdprinting ;
|
||||
bool cardOK ;
|
||||
bool paused ;
|
||||
char filename[13];
|
||||
uint16_t modificationTime, modificationDate;
|
||||
uint32_t cluster, position;
|
||||
|
||||
@ -582,30 +582,8 @@ void get_command()
|
||||
((serial_char == '#' || serial_char == ':') && comment_mode == false) ||
|
||||
serial_count >= (MAX_CMD_SIZE - 1) || n==-1)
|
||||
{
|
||||
if(card.eof()){
|
||||
SERIAL_PROTOCOLLNRPGM(_n("Done printing file"));////MSG_FILE_PRINTED
|
||||
stoptime=_millis();
|
||||
char time[30];
|
||||
unsigned long t=(stoptime-starttime-pause_time)/1000;
|
||||
pause_time = 0;
|
||||
int hours, minutes;
|
||||
minutes=(t/60)%60;
|
||||
hours=t/60/60;
|
||||
save_statistics(total_filament_used, t);
|
||||
sprintf_P(time, PSTR("%i hours %i minutes"),hours, minutes);
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLN(time);
|
||||
lcd_setstatus(time);
|
||||
card.printingHasFinished();
|
||||
card.checkautostart(true);
|
||||
if(card.eof()) break;
|
||||
|
||||
if (farm_mode)
|
||||
{
|
||||
prusa_statistics(6);
|
||||
lcd_commands_type = LcdCommands::FarmModeConfirm;
|
||||
}
|
||||
|
||||
}
|
||||
if(serial_char=='#')
|
||||
stop_buffering=true;
|
||||
|
||||
@ -663,6 +641,37 @@ void get_command()
|
||||
else if(!comment_mode) cmdbuffer[bufindw+CMDHDRSIZE+serial_count++] = serial_char;
|
||||
}
|
||||
}
|
||||
if(card.eof())
|
||||
{
|
||||
// file was fully buffered, but commands might still need to be planned!
|
||||
// do *not* clear sdprinting until all SD commands are consumed to ensure
|
||||
// SD state can be resumed from a saved printing state. sdprinting is only
|
||||
// cleared by printingHasFinished after peforming all remaining moves.
|
||||
if(!cmdqueue_calc_sd_length())
|
||||
{
|
||||
SERIAL_PROTOCOLLNRPGM(_n("Done printing file"));////MSG_FILE_PRINTED
|
||||
stoptime=_millis();
|
||||
char time[30];
|
||||
unsigned long t=(stoptime-starttime-pause_time)/1000;
|
||||
pause_time = 0;
|
||||
int hours, minutes;
|
||||
minutes=(t/60)%60;
|
||||
hours=t/60/60;
|
||||
save_statistics(total_filament_used, t);
|
||||
sprintf_P(time, PSTR("%i hours %i minutes"),hours, minutes);
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLN(time);
|
||||
lcd_setstatus(time);
|
||||
card.printingHasFinished();
|
||||
card.checkautostart(true);
|
||||
|
||||
if (farm_mode)
|
||||
{
|
||||
prusa_statistics(6);
|
||||
lcd_commands_type = LcdCommands::FarmModeConfirm;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
#endif //SDSUPPORT
|
||||
}
|
||||
|
||||
@ -74,7 +74,7 @@ static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEP
|
||||
#define EEPROM_UVLO_CURRENT_POSITION_Z (EEPROM_FILE_POSITION - 4) //float for current position in Z
|
||||
#define EEPROM_UVLO_TARGET_HOTEND (EEPROM_UVLO_CURRENT_POSITION_Z - 1)
|
||||
#define EEPROM_UVLO_TARGET_BED (EEPROM_UVLO_TARGET_HOTEND - 1)
|
||||
#define EEPROM_UVLO_FEEDRATE (EEPROM_UVLO_TARGET_BED - 2)
|
||||
#define EEPROM_UVLO_FEEDRATE (EEPROM_UVLO_TARGET_BED - 2) //uint16_t
|
||||
#define EEPROM_UVLO_FAN_SPEED (EEPROM_UVLO_FEEDRATE - 1)
|
||||
#define EEPROM_FAN_CHECK_ENABLED (EEPROM_UVLO_FAN_SPEED - 1)
|
||||
#define EEPROM_UVLO_MESH_BED_LEVELING (EEPROM_FAN_CHECK_ENABLED - 9*2)
|
||||
@ -204,9 +204,11 @@ static Sheets * const EEPROM_Sheets_base = (Sheets*)(EEPROM_SHEETS_BASE);
|
||||
#define EEPROM_FSENSOR_PCB (EEPROM_SHEETS_BASE-1) // uint8
|
||||
#define EEPROM_FSENSOR_ACTION_NA (EEPROM_FSENSOR_PCB-1) // uint8
|
||||
|
||||
#define EEPROM_UVLO_SAVED_TARGET (EEPROM_FSENSOR_ACTION_NA - 4*4) // 4 x float for saved target for all axes
|
||||
#define EEPROM_UVLO_FEEDMULTIPLY (EEPROM_UVLO_SAVED_TARGET - 2) // uint16_t for feedmultiply
|
||||
|
||||
//This is supposed to point to last item to allow EEPROM overrun check. Please update when adding new items.
|
||||
#define EEPROM_LAST_ITEM EEPROM_SHEETS_BASE
|
||||
#define EEPROM_LAST_ITEM EEPROM_UVLO_FEEDMULTIPLY
|
||||
// !!!!!
|
||||
// !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!!
|
||||
// !!!!!
|
||||
|
||||
@ -57,15 +57,8 @@ bool fsensor_enabled = true;
|
||||
bool fsensor_watch_runout = true;
|
||||
//! not responding - is set if any communication error occurred during initialization or readout
|
||||
bool fsensor_not_responding = false;
|
||||
//! printing saved
|
||||
bool fsensor_printing_saved = false;
|
||||
//! enable/disable quality meassurement
|
||||
bool fsensor_oq_meassure_enabled = false;
|
||||
//! as explained in the CHECK_FSENSOR macro: this flag is set to true when fsensor posts
|
||||
//! the M600 into the command queue, which elliminates the hazard of having posted multiple M600's
|
||||
//! before the first one gets read and started processing.
|
||||
//! Btw., the IR fsensor could do up to 6 posts before the command queue managed to start processing the first M600 ;)
|
||||
static bool fsensor_m600_enqueued = false;
|
||||
|
||||
//! number of errors, updated in ISR
|
||||
uint8_t fsensor_err_cnt = 0;
|
||||
@ -137,12 +130,19 @@ void fsensor_stop_and_save_print(void)
|
||||
void fsensor_restore_print_and_continue(void)
|
||||
{
|
||||
printf_P(PSTR("fsensor_restore_print_and_continue\n"));
|
||||
fsensor_watch_runout = true;
|
||||
fsensor_err_cnt = 0;
|
||||
fsensor_m600_enqueued = false;
|
||||
restore_print_from_ram_and_continue(0); //XYZ = orig, E - no change
|
||||
}
|
||||
|
||||
// fsensor_checkpoint_print cuts the current print job at the current position,
|
||||
// allowing new instructions to be inserted in the middle
|
||||
void fsensor_checkpoint_print(void)
|
||||
{
|
||||
printf_P(PSTR("fsensor_checkpoint_print\n"));
|
||||
stop_and_save_print_to_ram(0, 0);
|
||||
restore_print_from_ram_and_continue(0);
|
||||
}
|
||||
|
||||
void fsensor_init(void)
|
||||
{
|
||||
#ifdef PAT9125
|
||||
@ -565,8 +565,6 @@ void fsensor_enque_M600(){
|
||||
printf_P(PSTR("fsensor_update - M600\n"));
|
||||
eeprom_update_byte((uint8_t*)EEPROM_FERROR_COUNT, eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT) + 1);
|
||||
eeprom_update_word((uint16_t*)EEPROM_FERROR_COUNT_TOT, eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT) + 1);
|
||||
enquecommand_front_P(PSTR("PRUSA fsensor_recover"));
|
||||
fsensor_m600_enqueued = true;
|
||||
enquecommand_front_P((PSTR("M600")));
|
||||
}
|
||||
|
||||
@ -578,7 +576,7 @@ void fsensor_enque_M600(){
|
||||
void fsensor_update(void)
|
||||
{
|
||||
#ifdef PAT9125
|
||||
if (fsensor_enabled && fsensor_watch_runout && (fsensor_err_cnt > FSENSOR_ERR_MAX) && ( ! fsensor_m600_enqueued) )
|
||||
if (fsensor_enabled && fsensor_watch_runout && (fsensor_err_cnt > FSENSOR_ERR_MAX))
|
||||
{
|
||||
bool autoload_enabled_tmp = fsensor_autoload_enabled;
|
||||
fsensor_autoload_enabled = false;
|
||||
@ -611,22 +609,18 @@ void fsensor_update(void)
|
||||
err |= (fsensor_oq_er_sum > 2);
|
||||
err |= (fsensor_oq_yd_sum < (4 * FSENSOR_OQ_MIN_YD));
|
||||
|
||||
if (!err)
|
||||
{
|
||||
printf_P(PSTR("fsensor_err_cnt = 0\n"));
|
||||
fsensor_restore_print_and_continue();
|
||||
}
|
||||
else
|
||||
{
|
||||
fsensor_enque_M600();
|
||||
fsensor_watch_runout = false;
|
||||
}
|
||||
fsensor_restore_print_and_continue();
|
||||
fsensor_autoload_enabled = autoload_enabled_tmp;
|
||||
fsensor_oq_meassure_enabled = oq_meassure_enabled_tmp;
|
||||
|
||||
if (!err)
|
||||
printf_P(PSTR("fsensor_err_cnt = 0\n"));
|
||||
else
|
||||
fsensor_enque_M600();
|
||||
}
|
||||
#else //PAT9125
|
||||
if (CHECK_FSENSOR && fsensor_enabled && ir_sensor_detected && ( ! fsensor_m600_enqueued) )
|
||||
{
|
||||
if (CHECK_FSENSOR && fsensor_enabled && ir_sensor_detected)
|
||||
{
|
||||
if(digitalRead(IR_SENSOR_PIN))
|
||||
{ // IR_SENSOR_PIN ~ H
|
||||
#if IR_SENSOR_ANALOG
|
||||
@ -670,8 +664,8 @@ void fsensor_update(void)
|
||||
else
|
||||
{
|
||||
#endif //IR_SENSOR_ANALOG
|
||||
fsensor_stop_and_save_print();
|
||||
fsensor_enque_M600();
|
||||
fsensor_checkpoint_print();
|
||||
fsensor_enque_M600();
|
||||
#if IR_SENSOR_ANALOG
|
||||
}
|
||||
}
|
||||
|
||||
@ -21,6 +21,8 @@ extern bool fsensor_oq_meassure_enabled;
|
||||
extern void fsensor_stop_and_save_print(void);
|
||||
//! restore print - restore position and heatup to original temperature
|
||||
extern void fsensor_restore_print_and_continue(void);
|
||||
//! split the current gcode stream to insert new instructions
|
||||
extern void fsensor_checkpoint_print(void);
|
||||
//! @}
|
||||
|
||||
//! initialize
|
||||
|
||||
@ -382,8 +382,7 @@ void mmu_loop(void)
|
||||
FDEBUG_PRINTF_P(PSTR("MMU => '%dok'\n"), mmu_finda);
|
||||
//printf_P(PSTR("Eact: %d\n"), int(e_active()));
|
||||
if (!mmu_finda && CHECK_FSENSOR && fsensor_enabled) {
|
||||
fsensor_stop_and_save_print();
|
||||
enquecommand_front_P(PSTR("PRUSA fsensor_recover")); //then recover
|
||||
fsensor_checkpoint_print();
|
||||
ad_markDepleted(mmu_extruder);
|
||||
if (lcd_autoDepleteEnabled() && !ad_allDepleted())
|
||||
{
|
||||
|
||||
@ -659,15 +659,15 @@ float junction_deviation = 0.1;
|
||||
// Add a new linear movement to the buffer. steps_x, _y and _z is the absolute position in
|
||||
// mm. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
|
||||
// calculation the caller must also provide the physical length of the line in millimeters.
|
||||
void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder)
|
||||
void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder, const float* gcode_target)
|
||||
{
|
||||
// Calculate the buffer head after we push this byte
|
||||
int next_buffer_head = next_block_index(block_buffer_head);
|
||||
|
||||
// If the buffer is full: good! That means we are well ahead of the robot.
|
||||
// Rest here until there is room in the buffer.
|
||||
waiting_inside_plan_buffer_line_print_aborted = false;
|
||||
if (block_buffer_tail == next_buffer_head) {
|
||||
waiting_inside_plan_buffer_line_print_aborted = false;
|
||||
do {
|
||||
manage_heater();
|
||||
// Vojtech: Don't disable motors inside the planner!
|
||||
@ -687,6 +687,29 @@ void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate
|
||||
planner_update_queue_min_counter();
|
||||
#endif /* PLANNER_DIAGNOSTICS */
|
||||
|
||||
// Prepare to set up new block
|
||||
block_t *block = &block_buffer[block_buffer_head];
|
||||
|
||||
// Mark block as not busy (Not executed by the stepper interrupt, could be still tinkered with.)
|
||||
block->busy = false;
|
||||
|
||||
// Set sdlen for calculating sd position
|
||||
block->sdlen = 0;
|
||||
|
||||
// Save original destination of the move
|
||||
if (gcode_target)
|
||||
memcpy(block->gcode_target, gcode_target, sizeof(block_t::gcode_target));
|
||||
else
|
||||
{
|
||||
block->gcode_target[X_AXIS] = x;
|
||||
block->gcode_target[Y_AXIS] = y;
|
||||
block->gcode_target[Z_AXIS] = z;
|
||||
block->gcode_target[E_AXIS] = e;
|
||||
}
|
||||
|
||||
// Save the global feedrate at scheduling time
|
||||
block->gcode_feedrate = feedrate;
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
apply_rotation_xyz(plan_bed_level_matrix, x, y, z);
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
@ -786,15 +809,6 @@ void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate
|
||||
}
|
||||
#endif
|
||||
|
||||
// Prepare to set up new block
|
||||
block_t *block = &block_buffer[block_buffer_head];
|
||||
|
||||
// Set sdlen for calculating sd position
|
||||
block->sdlen = 0;
|
||||
|
||||
// Mark block as not busy (Not executed by the stepper interrupt, could be still tinkered with.)
|
||||
block->busy = false;
|
||||
|
||||
// Number of steps for each axis
|
||||
#ifndef COREXY
|
||||
// default non-h-bot planning
|
||||
|
||||
@ -116,7 +116,10 @@ typedef struct {
|
||||
unsigned long abs_adv_steps_multiplier8; // Factorised by 2^8 to avoid float
|
||||
#endif
|
||||
|
||||
uint16_t sdlen;
|
||||
// Save/recovery state data
|
||||
float gcode_target[NUM_AXIS]; // Target (abs mm) of the original Gcode instruction
|
||||
uint16_t gcode_feedrate; // Default and/or move feedrate
|
||||
uint16_t sdlen; // Length of the Gcode instruction
|
||||
} block_t;
|
||||
|
||||
#ifdef LIN_ADVANCE
|
||||
@ -147,7 +150,7 @@ vector_3 plan_get_position();
|
||||
/// The performance penalty is negligible, since these planned lines are usually maintenance moves with the extruder.
|
||||
void plan_buffer_line_curposXYZE(float feed_rate, uint8_t extruder);
|
||||
|
||||
void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder);
|
||||
void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder, const float* gcode_target = NULL);
|
||||
//void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t &extruder);
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
@ -238,6 +241,7 @@ FORCE_INLINE bool planner_queue_full() {
|
||||
// wait for the steppers to stop,
|
||||
// update planner's current position and the current_position of the front end.
|
||||
extern void planner_abort_hard();
|
||||
extern bool waiting_inside_plan_buffer_line_print_aborted;
|
||||
|
||||
#ifdef PREVENT_DANGEROUS_EXTRUDE
|
||||
void set_extrude_min_temp(float temp);
|
||||
|
||||
@ -4108,7 +4108,7 @@ void prusa_statistics(int _message, uint8_t _fil_nr) {
|
||||
{
|
||||
prusa_statistics_case0(15);
|
||||
}
|
||||
else if (isPrintPaused || card.paused)
|
||||
else if (isPrintPaused)
|
||||
{
|
||||
prusa_statistics_case0(14);
|
||||
}
|
||||
|
||||
@ -198,7 +198,7 @@ void prusa_statistics(int _message, uint8_t _fil_nr) {
|
||||
SERIAL_ECHOLN("}");
|
||||
status_number = 15;
|
||||
}
|
||||
else if (isPrintPaused || card.paused)
|
||||
else if (isPrintPaused)
|
||||
{
|
||||
SERIAL_ECHO("{");
|
||||
prusa_stat_printerstatus(14);
|
||||
@ -490,7 +490,7 @@ void prusa_statistics(int _message, uint8_t _fil_nr) {
|
||||
{
|
||||
prusa_statistics_case0(15);
|
||||
}
|
||||
else if (isPrintPaused || card.paused)
|
||||
else if (isPrintPaused)
|
||||
{
|
||||
prusa_statistics_case0(14);
|
||||
}
|
||||
@ -753,7 +753,6 @@ TEST_CASE("Prusa_statistics test", "[prusa_stats]")
|
||||
SERIALS_RESET();
|
||||
|
||||
isPrintPaused = 0;
|
||||
card.paused = 0;
|
||||
IS_SD_PRINTING = 1;
|
||||
old_code::prusa_statistics(test_codes[i],0);
|
||||
new_code::prusa_statistics(test_codes[i],0);
|
||||
|
||||
Loading…
Reference in New Issue
Block a user