From a220c97f94832de2b71bec5a962df505e788ebdf Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 16:19:30 +0100 Subject: [PATCH 01/11] Revert "variant files" This reverts commit 850d3316b6ab048bfa869383628d5b2fd7f3b75b. --- .../1_75mm_MK25S-RAMBo10a-E3Dv6full.h | 505 ++++++++++++++ .../1_75mm_MK25S-RAMBo13a-E3Dv6full.h | 506 ++++++++++++++ .../variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h | 631 ++++++++++++++++++ 3 files changed, 1642 insertions(+) create mode 100644 Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h create mode 100644 Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h create mode 100644 Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h diff --git a/Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h b/Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h new file mode 100644 index 00000000..53b545e8 --- /dev/null +++ b/Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h @@ -0,0 +1,505 @@ +#ifndef CONFIGURATION_PRUSA_H +#define CONFIGURATION_PRUSA_H + +#include +/*------------------------------------ + GENERAL SETTINGS + *------------------------------------*/ + +// Printer revision +#define PRINTER_TYPE PRINTER_MK25S +#define FILAMENT_SIZE "1_75mm_MK25S" +#define NOZZLE_TYPE "E3Dv6full" + +// Developer flag +#define DEVELOPER + +// Printer name +#define CUSTOM_MENDEL_NAME "Prusa i3 MK2.5S" + +// Electronics +#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 + +#define HEATBED_V2 +#define STEEL_SHEET +#define TACH0PULLUP + +// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier) +//#define E3D_PT100_EXTRUDER_WITH_AMP +//#define E3D_PT100_EXTRUDER_NO_AMP +//#define E3D_PT100_BED_WITH_AMP +//#define E3D_PT100_BED_NO_AMP + + +/*------------------------------------ + AXIS SETTINGS + *------------------------------------*/ + +// Steps per unit {X,Y,Z,E} +#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,133} + +// Endstop inverting +#define X_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. + +// Direction inverting +#define INVERT_X_DIR 0 // for Mendel set to 0, for Orca set to 1 +#define INVERT_Y_DIR 0 // for Mendel set to 1, for Orca set to 0 +#define INVERT_Z_DIR 0 // for Mendel set to 0, for Orca set to 1 +#define INVERT_E0_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E1_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E2_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 + +// Home position +#define MANUAL_X_HOME_POS 0 +#define MANUAL_Y_HOME_POS -2.2 +#define MANUAL_Z_HOME_POS 0.2 + +// Travel limits after homing +#define X_MAX_POS 250 +#define X_MIN_POS 0 +#define Y_MAX_POS 210 +#define Y_MIN_POS -4 +#define Z_MAX_POS 210 +#define Z_MIN_POS 0.15 + +// Canceled home position +#define X_CANCEL_POS 50 +#define Y_CANCEL_POS 190 + +//Pause print position +#define X_PAUSE_POS 50 +#define Y_PAUSE_POS 190 +#define Z_PAUSE_LIFT 20 + +#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E +#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000 + +/** + * [0,0] steel sheet print area point X coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_X 0.f +/** + * [0,0] steel sheet print area point Y coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_Y 0.f + +#define DEFAULT_MAX_FEEDRATE {200, 200, 12, 120} // (mm/sec) max feedrate (M203) +#define DEFAULT_MAX_FEEDRATE_SILENT {172, 172, 12, 120} // (mm/sec) max feedrate (M203), silent mode +#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // (mm/sec^2) max acceleration (M201) +#define DEFAULT_MAX_ACCELERATION_SILENT {960, 960, 200, 5000} // (mm/sec^2) max acceleration (M201), silent mode + +#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S) +#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T) + +#define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) + +//number of bytes from end of the file to start check +#define END_FILE_SECTION 20000 + +#define Z_AXIS_ALWAYS_ON 1 + +// New XYZ calibration +#define NEW_XYZCAL + +// Fan check +#define FANCHECK + +// Safety timer +#define SAFETYTIMER +#define DEFAULT_SAFETYTIMER_TIME_MINS 30 + +// Filament sensor +#define FILAMENT_SENSOR +#define IR_SENSOR + + +#define DEBUG_DCODE3 + +//#define DEBUG_BUILD +#ifdef DEBUG_BUILD +//#define _NO_ASM +#define DEBUG_DCODES //D codes +#define DEBUG_STACK_MONITOR //Stack monitor in stepper ISR +//#define DEBUG_FSENSOR_LOG //Reports fsensor status to serial +//#define DEBUG_CRASHDET_COUNTERS //Display crash-detection counters on LCD +//#define DEBUG_RESUME_PRINT //Resume/save print debug enable +//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output +//#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored +//#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored +//#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored +//#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored +//#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored +//#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored +//#define DEBUG_DISABLE_STARTMSGS //no startup messages +//#define DEBUG_DISABLE_MINTEMP //mintemp error ignored +//#define DEBUG_DISABLE_SWLIMITS //sw limits ignored +//#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line +//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed +//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages +//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) +//#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) +//#define DEBUG_DISABLE_FANCHECK //disable fan check (no ISR INT7, check disabled) +//#define DEBUG_DUMP_TO_2ND_SERIAL //dump received characters to 2nd serial line +//#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message. +//#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display. +//#define CMD_DIAGNOSTICS //Show cmd queue length on printer display +#endif /* DEBUG_BUILD */ + +//#define FSENSOR_QUALITY + + +/*------------------------------------ + EXTRUDER SETTINGS + *------------------------------------*/ + +// Mintemps +#define HEATER_0_MINTEMP 30 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_MINTEMP_DELAY 15000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if HEATER_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)" +#endif +#define BED_MINTEMP 30 +#define BED_MINTEMP_DELAY 50000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if BED_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)" +#endif + +// Maxtemps +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +#define HEATER_0_MAXTEMP 410 +#else +#define HEATER_0_MAXTEMP 305 +#endif +#define HEATER_1_MAXTEMP 305 +#define HEATER_2_MAXTEMP 305 +#define BED_MAXTEMP 125 + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_Kp 21.70 +#define DEFAULT_Ki 1.60 +#define DEFAULT_Kd 73.76 +#else +// Define PID constants for extruder +//#define DEFAULT_Kp 40.925 +//#define DEFAULT_Ki 4.875 +//#define DEFAULT_Kd 86.085 +#define DEFAULT_Kp 16.13 +#define DEFAULT_Ki 1.1625 +#define DEFAULT_Kd 56.23 +#endif + +// Extrude mintemp +#define EXTRUDE_MINTEMP 175 + +// Extruder cooling fans +#define EXTRUDER_0_AUTO_FAN_PIN 8 +#define EXTRUDER_1_AUTO_FAN_PIN -1 +#define EXTRUDER_2_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + + +/*------------------------------------ + LOAD/UNLOAD FILAMENT SETTINGS + *------------------------------------*/ + +// Load filament commands +#define LOAD_FILAMENT_0 "M83" +#define LOAD_FILAMENT_1 "G1 E70 F400" +#define LOAD_FILAMENT_2 "G1 E40 F100" + +// Unload filament commands +#define UNLOAD_FILAMENT_0 "M83" +#define UNLOAD_FILAMENT_1 "G1 E-80 F7000" + +/*------------------------------------ + CHANGE FILAMENT SETTINGS + *------------------------------------*/ + +// Filament change configuration +#define FILAMENTCHANGEENABLE +#ifdef FILAMENTCHANGEENABLE +#define FILAMENTCHANGE_XPOS 211 +#define FILAMENTCHANGE_YPOS 0 +#define FILAMENTCHANGE_ZADD 2 +#define FILAMENTCHANGE_FIRSTRETRACT -2 +#define FILAMENTCHANGE_FINALRETRACT -80 + +#define FILAMENTCHANGE_FIRSTFEED 70 //E distance in mm for fast filament loading sequence used used in filament change (M600) +#define FILAMENTCHANGE_FINALFEED 25 //E distance in mm for slow filament loading sequence used used in filament change (M600) and filament load (M701) +#define FILAMENTCHANGE_RECFEED 5 + +#define FILAMENTCHANGE_XYFEED 50 +#define FILAMENTCHANGE_EFEED_FIRST 20 // feedrate in mm/s for fast filament loading sequence used in filament change (M600) +#define FILAMENTCHANGE_EFEED_FINAL 3.3f // feedrate in mm/s for slow filament loading sequence used in filament change (M600) and filament load (M701) +//#define FILAMENTCHANGE_RFEED 400 +#define FILAMENTCHANGE_RFEED 7000 / 60 +#define FILAMENTCHANGE_EXFEED 2 +#define FILAMENTCHANGE_ZFEED 15 + +#endif + +/*------------------------------------ + ADDITIONAL FEATURES SETTINGS + *------------------------------------*/ + +// Define Prusa filament runout sensor +//#define FILAMENT_RUNOUT_SUPPORT + +#ifdef FILAMENT_RUNOUT_SUPPORT +#define FILAMENT_RUNOUT_SENSOR 1 +#endif + +// temperature runaway +#define TEMP_RUNAWAY_BED_HYSTERESIS 5 +#define TEMP_RUNAWAY_BED_TIMEOUT 360 + +#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 +#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 + +/*------------------------------------ + MOTOR CURRENT SETTINGS + *------------------------------------*/ + +// Motor Current setting for BIG RAMBo +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} + +// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range +#if MOTHERBOARD == BOARD_RAMBO_MINI_1_0 || MOTHERBOARD == BOARD_RAMBO_MINI_1_3 +#define MOTOR_CURRENT_PWM_RANGE 2000 +#define DEFAULT_PWM_MOTOR_CURRENT {270, 830, 450} // {XY,Z,E} +#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 830, 500} // {XY,Z,E} +#define Z_SILENT 0 +#define Z_HIGH_POWER 200 +#endif + +/*------------------------------------ + BED SETTINGS + *------------------------------------*/ + +// Define Mesh Bed Leveling system to enable it +#define MESH_BED_LEVELING +#ifdef MESH_BED_LEVELING + +#define MBL_Z_STEP 0.01 + +// Mesh definitions +#define MESH_MIN_X 35 +#define MESH_MAX_X 238 +#define MESH_MIN_Y 6 +#define MESH_MAX_Y 202 + +// Mesh upsample definition +#define MESH_NUM_X_POINTS 7 +#define MESH_NUM_Y_POINTS 7 +// Mesh measure definition +#define MESH_MEAS_NUM_X_POINTS 3 +#define MESH_MEAS_NUM_Y_POINTS 3 + +// Maximum bed level correction value +#define BED_ADJUSTMENT_UM_MAX 100 + +#define MESH_HOME_Z_CALIB 0.2 +#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc. + +#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right +#define Y_PROBE_OFFSET_FROM_EXTRUDER 5 // Z probe to nozzle Y offset: -front +behind +#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) +#endif + +// Bed Temperature Control +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +// Bed temperature compensation settings +#define BED_OFFSET 10 +#define BED_OFFSET_START 40 +#define BED_OFFSET_CENTER 50 + + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) +#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_bedKp 21.70 +#define DEFAULT_bedKi 1.60 +#define DEFAULT_bedKd 73.76 +#else +#define DEFAULT_bedKp 126.13 +#define DEFAULT_bedKi 4.30 +#define DEFAULT_bedKd 924.76 +#endif + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + + +/*----------------------------------- + PREHEAT SETTINGS + *------------------------------------*/ + +#define FARM_PREHEAT_HOTEND_TEMP 250 +#define FARM_PREHEAT_HPB_TEMP 40 +#define FARM_PREHEAT_FAN_SPEED 0 + +#define PLA_PREHEAT_HOTEND_TEMP 215 +#define PLA_PREHEAT_HPB_TEMP 60 +#define PLA_PREHEAT_FAN_SPEED 0 + +#define ABS_PREHEAT_HOTEND_TEMP 255 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 0 + +#define HIPS_PREHEAT_HOTEND_TEMP 220 +#define HIPS_PREHEAT_HPB_TEMP 100 +#define HIPS_PREHEAT_FAN_SPEED 0 + +#define PP_PREHEAT_HOTEND_TEMP 254 +#define PP_PREHEAT_HPB_TEMP 100 +#define PP_PREHEAT_FAN_SPEED 0 + +#define PET_PREHEAT_HOTEND_TEMP 230 +#define PET_PREHEAT_HPB_TEMP 85 +#define PET_PREHEAT_FAN_SPEED 0 + +#define FLEX_PREHEAT_HOTEND_TEMP 240 +#define FLEX_PREHEAT_HPB_TEMP 50 +#define FLEX_PREHEAT_FAN_SPEED 0 + +/*------------------------------------ + THERMISTORS SETTINGS + *------------------------------------*/ + +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a +// 247 is Pt100 with 4k7 pullup and PT100 Amplifier +// 110 is Pt100 with 1k pullup (non standard) + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) +#define TEMP_SENSOR_0 247 +#elif defined(E3D_PT100_EXTRUDER_NO_AMP) +#define TEMP_SENSOR_0 148 +#else +#define TEMP_SENSOR_0 5 +#endif +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#if defined(E3D_PT100_BED_WITH_AMP) +#define TEMP_SENSOR_BED 247 +#elif defined(E3D_PT100_BED_NO_AMP) +#define TEMP_SENSOR_BED 148 +#else +#define TEMP_SENSOR_BED 1 +#endif +#define TEMP_SENSOR_PINDA 1 + +#define STACK_GUARD_TEST_VALUE 0xA2A2 + +#define MAX_BED_TEMP_CALIBRATION 50 +#define MAX_HOTEND_TEMP_CALIBRATION 50 + +#define MAX_E_STEPS_PER_UNIT 250 +#define MIN_E_STEPS_PER_UNIT 100 + +#define Z_BABYSTEP_MIN -3999 +#define Z_BABYSTEP_MAX 0 + +#define PINDA_PREHEAT_X 20 +#define PINDA_PREHEAT_Y 60 +#define PINDA_PREHEAT_Z 0.15 +/* +#define PINDA_PREHEAT_X 70 +#define PINDA_PREHEAT_Y -3 +#define PINDA_PREHEAT_Z 1*/ +#define PINDA_HEAT_T 120 //time in s + +#define PINDA_MIN_T 50 +#define PINDA_STEP_T 10 +#define PINDA_MAX_T 100 + +#define PING_TIME 60 //time in s +#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes +#define PING_ALLERT_PERIOD 60 //time in s + +#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring +#define NC_BUTTON_LONG_PRESS 15 //time in s + +#define LONG_PRESS_TIME 1000 //time in ms for button long press +#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release + +#define DEFAULT_PID_TEMP 210 + +#define MIN_PRINT_FAN_SPEED 75 + + +#define M600_TIMEOUT 600 //seconds + +//#define SUPPORT_VERBOSITY + +#define MMU_REQUIRED_FW_BUILDNR 132 +//#define MMU_DEBUG //print communication between MMU2 and printer on serial + +#define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning + +#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h b/Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h new file mode 100644 index 00000000..e786b70f --- /dev/null +++ b/Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h @@ -0,0 +1,506 @@ +#ifndef CONFIGURATION_PRUSA_H +#define CONFIGURATION_PRUSA_H + +#include +/*------------------------------------ + GENERAL SETTINGS + *------------------------------------*/ + +// Printer revision +#define PRINTER_TYPE PRINTER_MK25S +#define FILAMENT_SIZE "1_75mm_MK25" +#define NOZZLE_TYPE "E3Dv6full" + +// Developer flag +#define DEVELOPER + +// Printer name +#define CUSTOM_MENDEL_NAME "Prusa i3 MK2.5S" + +// Electronics +#define MOTHERBOARD BOARD_RAMBO_MINI_1_3 + +#define HEATBED_V2 +#define STEEL_SHEET +#define TACH0PULLUP + +// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier) +//#define E3D_PT100_EXTRUDER_WITH_AMP +//#define E3D_PT100_EXTRUDER_NO_AMP +//#define E3D_PT100_BED_WITH_AMP +//#define E3D_PT100_BED_NO_AMP + + +/*------------------------------------ + AXIS SETTINGS + *------------------------------------*/ + +// Steps per unit {X,Y,Z,E} +#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,133} + +// Endstop inverting +#define X_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. + +// Direction inverting +#define INVERT_X_DIR 0 // for Mendel set to 0, for Orca set to 1 +#define INVERT_Y_DIR 0 // for Mendel set to 1, for Orca set to 0 +#define INVERT_Z_DIR 0 // for Mendel set to 0, for Orca set to 1 +#define INVERT_E0_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E1_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E2_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0 + +// Home position +#define MANUAL_X_HOME_POS 0 +#define MANUAL_Y_HOME_POS -2.2 +#define MANUAL_Z_HOME_POS 0.2 + +// Travel limits after homing +#define X_MAX_POS 250 +#define X_MIN_POS 0 +#define Y_MAX_POS 210 +#define Y_MIN_POS -4 +#define Z_MAX_POS 210 +#define Z_MIN_POS 0.15 + +// Canceled home position +#define X_CANCEL_POS 50 +#define Y_CANCEL_POS 190 + +//Pause print position +#define X_PAUSE_POS 50 +#define Y_PAUSE_POS 190 +#define Z_PAUSE_LIFT 20 + +#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E +#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000 + +/** + * [0,0] steel sheet print area point X coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_X 0.f +/** + * [0,0] steel sheet print area point Y coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_Y 0.f + +#define DEFAULT_MAX_FEEDRATE {200, 200, 12, 120} // (mm/sec) max feedrate (M203) +#define DEFAULT_MAX_FEEDRATE_SILENT {172, 172, 12, 120} // (mm/sec) max feedrate (M203), silent mode +#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // (mm/sec^2) max acceleration (M201) +#define DEFAULT_MAX_ACCELERATION_SILENT {960, 960, 200, 5000} // (mm/sec^2) max acceleration (M201), silent mode + + +#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S) +#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T) + +#define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) + +//number of bytes from end of the file to start check +#define END_FILE_SECTION 20000 + +#define Z_AXIS_ALWAYS_ON 1 + +// New XYZ calibration +#define NEW_XYZCAL + +// Fan check +#define FANCHECK + +// Safety timer +#define SAFETYTIMER +#define DEFAULT_SAFETYTIMER_TIME_MINS 30 + +// Filament sensor +#define FILAMENT_SENSOR +#define IR_SENSOR + + +#define DEBUG_DCODE3 + +//#define DEBUG_BUILD +#ifdef DEBUG_BUILD +//#define _NO_ASM +#define DEBUG_DCODES //D codes +#define DEBUG_STACK_MONITOR //Stack monitor in stepper ISR +//#define DEBUG_FSENSOR_LOG //Reports fsensor status to serial +//#define DEBUG_CRASHDET_COUNTERS //Display crash-detection counters on LCD +//#define DEBUG_RESUME_PRINT //Resume/save print debug enable +//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output +//#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored +//#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored +//#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored +//#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored +//#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored +//#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored +//#define DEBUG_DISABLE_STARTMSGS //no startup messages +//#define DEBUG_DISABLE_MINTEMP //mintemp error ignored +//#define DEBUG_DISABLE_SWLIMITS //sw limits ignored +//#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line +//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed +//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages +//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) +//#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) +//#define DEBUG_DISABLE_FANCHECK //disable fan check (no ISR INT7, check disabled) +//#define DEBUG_DUMP_TO_2ND_SERIAL //dump received characters to 2nd serial line +//#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message. +//#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display. +//#define CMD_DIAGNOSTICS //Show cmd queue length on printer display +#endif /* DEBUG_BUILD */ + +//#define FSENSOR_QUALITY + + +/*------------------------------------ + EXTRUDER SETTINGS + *------------------------------------*/ + +// Mintemps +#define HEATER_0_MINTEMP 30 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_MINTEMP_DELAY 15000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if HEATER_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)" +#endif +#define BED_MINTEMP 30 +#define BED_MINTEMP_DELAY 50000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if BED_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)" +#endif + +// Maxtemps +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +#define HEATER_0_MAXTEMP 410 +#else +#define HEATER_0_MAXTEMP 305 +#endif +#define HEATER_1_MAXTEMP 305 +#define HEATER_2_MAXTEMP 305 +#define BED_MAXTEMP 125 + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_Kp 21.70 +#define DEFAULT_Ki 1.60 +#define DEFAULT_Kd 73.76 +#else +// Define PID constants for extruder +//#define DEFAULT_Kp 40.925 +//#define DEFAULT_Ki 4.875 +//#define DEFAULT_Kd 86.085 +#define DEFAULT_Kp 16.13 +#define DEFAULT_Ki 1.1625 +#define DEFAULT_Kd 56.23 +#endif + +// Extrude mintemp +#define EXTRUDE_MINTEMP 175 + +// Extruder cooling fans +#define EXTRUDER_0_AUTO_FAN_PIN 8 +#define EXTRUDER_1_AUTO_FAN_PIN -1 +#define EXTRUDER_2_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + + +/*------------------------------------ + LOAD/UNLOAD FILAMENT SETTINGS + *------------------------------------*/ + +// Load filament commands +#define LOAD_FILAMENT_0 "M83" +#define LOAD_FILAMENT_1 "G1 E70 F400" +#define LOAD_FILAMENT_2 "G1 E40 F100" + +// Unload filament commands +#define UNLOAD_FILAMENT_0 "M83" +#define UNLOAD_FILAMENT_1 "G1 E-80 F7000" + +/*------------------------------------ + CHANGE FILAMENT SETTINGS + *------------------------------------*/ + +// Filament change configuration +#define FILAMENTCHANGEENABLE +#ifdef FILAMENTCHANGEENABLE +#define FILAMENTCHANGE_XPOS 211 +#define FILAMENTCHANGE_YPOS 0 +#define FILAMENTCHANGE_ZADD 2 +#define FILAMENTCHANGE_FIRSTRETRACT -2 +#define FILAMENTCHANGE_FINALRETRACT -80 + +#define FILAMENTCHANGE_FIRSTFEED 70 //E distance in mm for fast filament loading sequence used used in filament change (M600) +#define FILAMENTCHANGE_FINALFEED 25 //E distance in mm for slow filament loading sequence used used in filament change (M600) and filament load (M701) +#define FILAMENTCHANGE_RECFEED 5 + +#define FILAMENTCHANGE_XYFEED 50 +#define FILAMENTCHANGE_EFEED_FIRST 20 // feedrate in mm/s for fast filament loading sequence used in filament change (M600) +#define FILAMENTCHANGE_EFEED_FINAL 3.3f // feedrate in mm/s for slow filament loading sequence used in filament change (M600) and filament load (M701) +//#define FILAMENTCHANGE_RFEED 400 +#define FILAMENTCHANGE_RFEED 7000 / 60 +#define FILAMENTCHANGE_EXFEED 2 +#define FILAMENTCHANGE_ZFEED 15 + +#endif + +/*------------------------------------ + ADDITIONAL FEATURES SETTINGS + *------------------------------------*/ + +// Define Prusa filament runout sensor +//#define FILAMENT_RUNOUT_SUPPORT + +#ifdef FILAMENT_RUNOUT_SUPPORT +#define FILAMENT_RUNOUT_SENSOR 1 +#endif + +// temperature runaway +#define TEMP_RUNAWAY_BED_HYSTERESIS 5 +#define TEMP_RUNAWAY_BED_TIMEOUT 360 + +#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 +#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 + +/*------------------------------------ + MOTOR CURRENT SETTINGS + *------------------------------------*/ + +// Motor Current setting for BIG RAMBo +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} + +// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range +#if MOTHERBOARD == BOARD_RAMBO_MINI_1_0 || MOTHERBOARD == BOARD_RAMBO_MINI_1_3 +#define MOTOR_CURRENT_PWM_RANGE 2000 +#define DEFAULT_PWM_MOTOR_CURRENT {270, 830, 450} // {XY,Z,E} +#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 830, 500} // {XY,Z,E} +#define Z_SILENT 0 +#define Z_HIGH_POWER 200 +#endif + +/*------------------------------------ + BED SETTINGS + *------------------------------------*/ + +// Define Mesh Bed Leveling system to enable it +#define MESH_BED_LEVELING +#ifdef MESH_BED_LEVELING + +#define MBL_Z_STEP 0.01 + +// Mesh definitions +#define MESH_MIN_X 35 +#define MESH_MAX_X 238 +#define MESH_MIN_Y 6 +#define MESH_MAX_Y 202 + +// Mesh upsample definition +#define MESH_NUM_X_POINTS 7 +#define MESH_NUM_Y_POINTS 7 +// Mesh measure definition +#define MESH_MEAS_NUM_X_POINTS 3 +#define MESH_MEAS_NUM_Y_POINTS 3 + +// Maximum bed level correction value +#define BED_ADJUSTMENT_UM_MAX 100 + +#define MESH_HOME_Z_CALIB 0.2 +#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc. + +#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right +#define Y_PROBE_OFFSET_FROM_EXTRUDER 5 // Z probe to nozzle Y offset: -front +behind +#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) +#endif + +// Bed Temperature Control +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +// Bed temperature compensation settings +#define BED_OFFSET 10 +#define BED_OFFSET_START 40 +#define BED_OFFSET_CENTER 50 + + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) +#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_bedKp 21.70 +#define DEFAULT_bedKi 1.60 +#define DEFAULT_bedKd 73.76 +#else +#define DEFAULT_bedKp 126.13 +#define DEFAULT_bedKi 4.30 +#define DEFAULT_bedKd 924.76 +#endif + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + + +/*----------------------------------- + PREHEAT SETTINGS + *------------------------------------*/ + +#define FARM_PREHEAT_HOTEND_TEMP 250 +#define FARM_PREHEAT_HPB_TEMP 40 +#define FARM_PREHEAT_FAN_SPEED 0 + +#define PLA_PREHEAT_HOTEND_TEMP 215 +#define PLA_PREHEAT_HPB_TEMP 60 +#define PLA_PREHEAT_FAN_SPEED 0 + +#define ABS_PREHEAT_HOTEND_TEMP 255 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 0 + +#define HIPS_PREHEAT_HOTEND_TEMP 220 +#define HIPS_PREHEAT_HPB_TEMP 100 +#define HIPS_PREHEAT_FAN_SPEED 0 + +#define PP_PREHEAT_HOTEND_TEMP 254 +#define PP_PREHEAT_HPB_TEMP 100 +#define PP_PREHEAT_FAN_SPEED 0 + +#define PET_PREHEAT_HOTEND_TEMP 230 +#define PET_PREHEAT_HPB_TEMP 85 +#define PET_PREHEAT_FAN_SPEED 0 + +#define FLEX_PREHEAT_HOTEND_TEMP 240 +#define FLEX_PREHEAT_HPB_TEMP 50 +#define FLEX_PREHEAT_FAN_SPEED 0 + +/*------------------------------------ + THERMISTORS SETTINGS + *------------------------------------*/ + +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a +// 247 is Pt100 with 4k7 pullup and PT100 Amplifier +// 110 is Pt100 with 1k pullup (non standard) + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) +#define TEMP_SENSOR_0 247 +#elif defined(E3D_PT100_EXTRUDER_NO_AMP) +#define TEMP_SENSOR_0 148 +#else +#define TEMP_SENSOR_0 5 +#endif +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#if defined(E3D_PT100_BED_WITH_AMP) +#define TEMP_SENSOR_BED 247 +#elif defined(E3D_PT100_BED_NO_AMP) +#define TEMP_SENSOR_BED 148 +#else +#define TEMP_SENSOR_BED 1 +#endif +#define TEMP_SENSOR_PINDA 1 + +#define STACK_GUARD_TEST_VALUE 0xA2A2 + +#define MAX_BED_TEMP_CALIBRATION 50 +#define MAX_HOTEND_TEMP_CALIBRATION 50 + +#define MAX_E_STEPS_PER_UNIT 250 +#define MIN_E_STEPS_PER_UNIT 100 + +#define Z_BABYSTEP_MIN -3999 +#define Z_BABYSTEP_MAX 0 + +#define PINDA_PREHEAT_X 20 +#define PINDA_PREHEAT_Y 60 +#define PINDA_PREHEAT_Z 0.15 +/* +#define PINDA_PREHEAT_X 70 +#define PINDA_PREHEAT_Y -3 +#define PINDA_PREHEAT_Z 1*/ +#define PINDA_HEAT_T 120 //time in s + +#define PINDA_MIN_T 50 +#define PINDA_STEP_T 10 +#define PINDA_MAX_T 100 + +#define PING_TIME 60 //time in s +#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes +#define PING_ALLERT_PERIOD 60 //time in s + +#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring +#define NC_BUTTON_LONG_PRESS 15 //time in s + +#define LONG_PRESS_TIME 1000 //time in ms for button long press +#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release + +#define DEFAULT_PID_TEMP 210 + +#define MIN_PRINT_FAN_SPEED 75 + + +#define M600_TIMEOUT 600 //seconds + +//#define SUPPORT_VERBOSITY + +#define MMU_REQUIRED_FW_BUILDNR 132 +//#define MMU_DEBUG //print communication between MMU2 and printer on serial + +#define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning + +#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h b/Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h new file mode 100644 index 00000000..37512071 --- /dev/null +++ b/Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h @@ -0,0 +1,631 @@ +#ifndef CONFIGURATION_PRUSA_H +#define CONFIGURATION_PRUSA_H + +#include +/*------------------------------------ + GENERAL SETTINGS + *------------------------------------*/ + +// Printer revision +#define PRINTER_TYPE PRINTER_MK3S +#define FILAMENT_SIZE "1_75mm_MK3" +#define NOZZLE_TYPE "E3Dv6full" + +// Developer flag +#define DEVELOPER + +// Printer name +#define CUSTOM_MENDEL_NAME "Prusa i3 MK3S" + +// Electronics +#define MOTHERBOARD BOARD_EINSY_1_0a +#define STEEL_SHEET +#define HAS_SECOND_SERIAL_PORT + + +// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier) +//#define E3D_PT100_EXTRUDER_WITH_AMP +//#define E3D_PT100_EXTRUDER_NO_AMP +//#define E3D_PT100_BED_WITH_AMP +//#define E3D_PT100_BED_NO_AMP + + +/*------------------------------------ + AXIS SETTINGS + *------------------------------------*/ + +// Steps per unit {X,Y,Z,E} +//#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,140} +#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,280} +//#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,560} + +// Endstop inverting +#define X_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop. + +// Direction inverting +#define INVERT_X_DIR 1 // for Mendel set to 0, for Orca set to 1 +#define INVERT_Y_DIR 0 // for Mendel set to 1, for Orca set to 0 +#define INVERT_Z_DIR 1 // for Mendel set to 0, for Orca set to 1 +#define INVERT_E0_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E1_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0 +#define INVERT_E2_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0 + +// Home position +#define MANUAL_X_HOME_POS 0 +#define MANUAL_Y_HOME_POS -2.2 +#define MANUAL_Z_HOME_POS 0.2 + +// Travel limits after homing +#define X_MAX_POS 255 +#define X_MIN_POS 0 +#define Y_MAX_POS 212.5 +#define Y_MIN_POS -4 //orig -4 +#define Z_MAX_POS 210 +#define Z_MIN_POS 0.15 + +// Canceled home position +#define X_CANCEL_POS 50 +#define Y_CANCEL_POS 190 + +//Pause print position +#define X_PAUSE_POS 50 +#define Y_PAUSE_POS 190 +#define Z_PAUSE_LIFT 20 + +#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E +#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000 + +//#define DEFAULT_Y_OFFSET 4.f // Default distance of Y_MIN_POS point from endstop, when the printer is not calibrated. +/** + * [0,0] steel sheet print area point X coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_X 0.f +/** + * [0,0] steel sheet print area point Y coordinate in bed print area coordinates + */ +#define SHEET_PRINT_ZERO_REF_Y -2.f + +#define DEFAULT_MAX_FEEDRATE {200, 200, 12, 120} // (mm/sec) max feedrate (M203) +#define DEFAULT_MAX_FEEDRATE_SILENT {100, 100, 12, 120} // (mm/sec) max feedrate (M203), silent mode + +#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // (mm/sec^2) max acceleration (M201) +#define DEFAULT_MAX_ACCELERATION_SILENT {960, 960, 200, 5000} // (mm/sec^2) max acceleration (M201), silent mode + + +#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S) +#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T) + +#define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) + +//Silent mode limits +#define SILENT_MAX_ACCEL_XY 960ul // max acceleration in silent mode in mm/s^2 +#define SILENT_MAX_FEEDRATE_XY 100 // max feedrate in mm/s + +//Normal mode limits +#define NORMAL_MAX_ACCEL_XY 2500ul // max acceleration in normal mode in mm/s^2 +#define NORMAL_MAX_FEEDRATE_XY 200 // max feedrate in mm/s + +//number of bytes from end of the file to start check +#define END_FILE_SECTION 20000 + +#define Z_AXIS_ALWAYS_ON 1 + +//Crash detection +#define CRASHDET_TIMER 45 //seconds +#define CRASHDET_COUNTER_MAX 3 + +// New XYZ calibration +#define NEW_XYZCAL + +// Watchdog support +#define WATCHDOG + +// Power panic +#define UVLO_SUPPORT + +// Fan check +#define FANCHECK + +// Safety timer +#define SAFETYTIMER +#define DEFAULT_SAFETYTIMER_TIME_MINS 30 + +// Filament sensor +#define FILAMENT_SENSOR +#define IR_SENSOR + +// Backlash - +//#define BACKLASH_X +//#define BACKLASH_Y + + +// Minimum ambient temperature limit to start triggering MINTEMP errors [C] +// this value is litlebit higher that real limit, because ambient termistor is on the board and is temperated from it, +// temperature inside the case is around 31C for ambient temperature 25C, when the printer is powered on long time and idle +// the real limit is 15C (same as MINTEMP limit), this is because 15C is end of scale for both used thermistors (bed, heater) +#define MINTEMP_MINAMBIENT 25 +#define MINTEMP_MINAMBIENT_RAW 978 + +#define DEBUG_DCODE3 + +//#define DEBUG_BUILD +//#define DEBUG_SEC_LANG //secondary language debug output at startup +//#define DEBUG_W25X20CL //debug external spi flash +#ifdef DEBUG_BUILD +//#define _NO_ASM +#define DEBUG_DCODES //D codes +#define DEBUG_STACK_MONITOR //Stack monitor in stepper ISR +//#define DEBUG_FSENSOR_LOG //Reports fsensor status to serial +//#define DEBUG_CRASHDET_COUNTERS //Display crash-detection counters on LCD +//#define DEBUG_RESUME_PRINT //Resume/save print debug enable +//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output +//#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored +//#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored +//#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored +//#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored +//#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored +//#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored +#define DEBUG_DISABLE_STARTMSGS //no startup messages +//#define DEBUG_DISABLE_MINTEMP //mintemp error ignored +//#define DEBUG_DISABLE_SWLIMITS //sw limits ignored +//#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line +//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed +//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages +//#define DEBUG_DISABLE_FORCE_SELFTEST //disable force selftest +//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) +//#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) +//#define DEBUG_DISABLE_FANCHECK //disable fan check (no ISR INT7, check disabled) +//#define DEBUG_DISABLE_FSENSORCHECK //disable fsensor check (no ISR INT7, check disabled) +#define DEBUG_DUMP_TO_2ND_SERIAL //dump received characters to 2nd serial line +#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message. +#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display. +#define CMD_DIAGNOSTICS //Show cmd queue length on printer display +#endif /* DEBUG_BUILD */ + +//#define FSENSOR_QUALITY + + +#define LINEARITY_CORRECTION +#define TMC2130_LINEARITY_CORRECTION +#define TMC2130_LINEARITY_CORRECTION_XYZ +//#define TMC2130_VARIABLE_RESOLUTION + + + +/*------------------------------------ + TMC2130 default settings + *------------------------------------*/ + +#define TMC2130_FCLK 12000000 // fclk = 12MHz + +#define TMC2130_USTEPS_XY 16 // microstep resolution for XY axes +#define TMC2130_USTEPS_Z 16 // microstep resolution for Z axis +#define TMC2130_USTEPS_E 32 // microstep resolution for E axis +#define TMC2130_INTPOL_XY 1 // extrapolate 256 for XY axes +#define TMC2130_INTPOL_Z 1 // extrapolate 256 for Z axis +#define TMC2130_INTPOL_E 1 // extrapolate 256 for E axis + +#define TMC2130_PWM_GRAD_X 2 // PWMCONF +#define TMC2130_PWM_AMPL_X 230 // PWMCONF +#define TMC2130_PWM_AUTO_X 1 // PWMCONF +#define TMC2130_PWM_FREQ_X 2 // PWMCONF + +#define TMC2130_PWM_GRAD_Y 2 // PWMCONF +#define TMC2130_PWM_AMPL_Y 235 // PWMCONF +#define TMC2130_PWM_AUTO_Y 1 // PWMCONF +#define TMC2130_PWM_FREQ_Y 2 // PWMCONF + +#define TMC2130_PWM_GRAD_Z 4 // PWMCONF +#define TMC2130_PWM_AMPL_Z 200 // PWMCONF +#define TMC2130_PWM_AUTO_Z 1 // PWMCONF +#define TMC2130_PWM_FREQ_Z 2 // PWMCONF + +#define TMC2130_PWM_GRAD_E 4 // PWMCONF +#define TMC2130_PWM_AMPL_E 240 // PWMCONF +#define TMC2130_PWM_AUTO_E 1 // PWMCONF +#define TMC2130_PWM_FREQ_E 2 // PWMCONF + +#define TMC2130_TOFF_XYZ 3 // CHOPCONF // fchop = 27.778kHz +#define TMC2130_TOFF_E 3 // CHOPCONF // fchop = 27.778kHz +//#define TMC2130_TOFF_E 4 // CHOPCONF // fchop = 21.429kHz +//#define TMC2130_TOFF_E 5 // CHOPCONF // fchop = 17.442kHz + +//#define TMC2130_STEALTH_E // Extruder stealthChop mode +//#define TMC2130_CNSTOFF_E // Extruder constant-off-time mode (similar to MK2) + +//#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410) +#define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410) +#define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk) + +#define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode +#define TMC2130_THIGH 0 // THIGH - unused + +//#define TMC2130_TCOOLTHRS_X 450 // TCOOLTHRS - coolstep treshold +//#define TMC2130_TCOOLTHRS_Y 450 // TCOOLTHRS - coolstep treshold +#define TMC2130_TCOOLTHRS_X 430 // TCOOLTHRS - coolstep treshold +#define TMC2130_TCOOLTHRS_Y 430 // TCOOLTHRS - coolstep treshold +#define TMC2130_TCOOLTHRS_Z 500 // TCOOLTHRS - coolstep treshold +#define TMC2130_TCOOLTHRS_E 500 // TCOOLTHRS - coolstep treshold + +#define TMC2130_SG_HOMING 1 // stallguard homing +#define TMC2130_SG_THRS_X 3 // stallguard sensitivity for X axis +#define TMC2130_SG_THRS_Y 3 // stallguard sensitivity for Y axis +#define TMC2130_SG_THRS_Z 4 // stallguard sensitivity for Z axis +#define TMC2130_SG_THRS_E 3 // stallguard sensitivity for E axis + +//new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right (Z axis only) +#define TMC2130_CURRENTS_H {16, 20, 35, 30} // default holding currents for all axes +#define TMC2130_CURRENTS_R {16, 20, 35, 30} // default running currents for all axes +#define TMC2130_UNLOAD_CURRENT_R 12 // lowe current for M600 to protect filament sensor + +#define TMC2130_STEALTH_Z + +//#define TMC2130_SERVICE_CODES_M910_M918 + +//#define TMC2130_DEBUG +//#define TMC2130_DEBUG_WR +//#define TMC2130_DEBUG_RD + + +/*------------------------------------ + EXTRUDER SETTINGS + *------------------------------------*/ + +// Mintemps +#define HEATER_0_MINTEMP 15 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_MINTEMP_DELAY 15000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if HEATER_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)" +#endif +#define BED_MINTEMP 15 +#define BED_MINTEMP_DELAY 50000 // [ms] ! if changed, check maximal allowed value @ ShortTimer +#if BED_MINTEMP_DELAY>USHRT_MAX +#error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)" +#endif + +// Maxtemps +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +#define HEATER_0_MAXTEMP 410 +#else +#define HEATER_0_MAXTEMP 305 +#endif +#define HEATER_1_MAXTEMP 305 +#define HEATER_2_MAXTEMP 305 +#define BED_MAXTEMP 125 + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_Kp 21.70 +#define DEFAULT_Ki 1.60 +#define DEFAULT_Kd 73.76 +#else +// Define PID constants for extruder +//#define DEFAULT_Kp 40.925 +//#define DEFAULT_Ki 4.875 +//#define DEFAULT_Kd 86.085 +#define DEFAULT_Kp 16.13 +#define DEFAULT_Ki 1.1625 +#define DEFAULT_Kd 56.23 +#endif + +// Extrude mintemp +#define EXTRUDE_MINTEMP 175 + +// Extruder cooling fans +#define EXTRUDER_0_AUTO_FAN_PIN 8 +#define EXTRUDER_1_AUTO_FAN_PIN -1 +#define EXTRUDER_2_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + + + +/*------------------------------------ + LOAD/UNLOAD FILAMENT SETTINGS + *------------------------------------*/ + +// Load filament commands +#define LOAD_FILAMENT_0 "M83" +#define LOAD_FILAMENT_1 "G1 E70 F400" +#define LOAD_FILAMENT_2 "G1 E40 F100" + +// Unload filament commands +#define UNLOAD_FILAMENT_0 "M83" +#define UNLOAD_FILAMENT_1 "G1 E-80 F7000" + +/*------------------------------------ + CHANGE FILAMENT SETTINGS + *------------------------------------*/ + +// Filament change configuration +#define FILAMENTCHANGEENABLE +#ifdef FILAMENTCHANGEENABLE +#define FILAMENTCHANGE_XPOS 211 +#define FILAMENTCHANGE_YPOS 0 +#define FILAMENTCHANGE_ZADD 2 +#define FILAMENTCHANGE_FIRSTRETRACT -2 +#define FILAMENTCHANGE_FINALRETRACT -80 + +#define FILAMENTCHANGE_FIRSTFEED 70 //E distance in mm for fast filament loading sequence used used in filament change (M600) +#define FILAMENTCHANGE_FINALFEED 25 //E distance in mm for slow filament loading sequence used used in filament change (M600) and filament load (M701) +#define FILAMENTCHANGE_RECFEED 5 + +#define FILAMENTCHANGE_XYFEED 50 +#define FILAMENTCHANGE_EFEED_FIRST 20 // feedrate in mm/s for fast filament loading sequence used in filament change (M600) +#define FILAMENTCHANGE_EFEED_FINAL 3.3f // feedrate in mm/s for slow filament loading sequence used in filament change (M600) and filament load (M701) +//#define FILAMENTCHANGE_RFEED 400 +#define FILAMENTCHANGE_RFEED 7000 / 60 +#define FILAMENTCHANGE_EXFEED 2 +#define FILAMENTCHANGE_ZFEED 15 + +#endif + +/*------------------------------------ + ADDITIONAL FEATURES SETTINGS + *------------------------------------*/ + +// Define Prusa filament runout sensor +//#define FILAMENT_RUNOUT_SUPPORT + +#ifdef FILAMENT_RUNOUT_SUPPORT +#define FILAMENT_RUNOUT_SENSOR 1 +#endif + +// temperature runaway +#define TEMP_RUNAWAY_BED_HYSTERESIS 5 +#define TEMP_RUNAWAY_BED_TIMEOUT 360 + +#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 +#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 + +/*------------------------------------ + MOTOR CURRENT SETTINGS + *------------------------------------*/ + +// Motor Current settings for Einsy/tmc = 0..63 +#define MOTOR_CURRENT_PWM_RANGE 63 + +/*------------------------------------ + BED SETTINGS + *------------------------------------*/ + +// Define Mesh Bed Leveling system to enable it +#define MESH_BED_LEVELING +#ifdef MESH_BED_LEVELING + +#define MBL_Z_STEP 0.01 + +// Mesh definitions +#define MESH_MIN_X 35 +#define MESH_MAX_X 238 +#define MESH_MIN_Y 6 +#define MESH_MAX_Y 202 + +// Mesh upsample definition +#define MESH_NUM_X_POINTS 7 +#define MESH_NUM_Y_POINTS 7 +// Mesh measure definition +#define MESH_MEAS_NUM_X_POINTS 3 +#define MESH_MEAS_NUM_Y_POINTS 3 + +// Maximum bed level correction value +#define BED_ADJUSTMENT_UM_MAX 100 + +#define MESH_HOME_Z_CALIB 0.2 +#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc. + +#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right +#define Y_PROBE_OFFSET_FROM_EXTRUDER 5 // Z probe to nozzle Y offset: -front +behind +#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) +#endif + +// Bed Temperature Control +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +// Bed temperature compensation settings +#define BED_OFFSET 10 +#define BED_OFFSET_START 40 +#define BED_OFFSET_CENTER 50 + + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) +#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP) +// Define PID constants for extruder with PT100 +#define DEFAULT_bedKp 21.70 +#define DEFAULT_bedKi 1.60 +#define DEFAULT_bedKd 73.76 +#else +#define DEFAULT_bedKp 126.13 +#define DEFAULT_bedKi 4.30 +#define DEFAULT_bedKd 924.76 +#endif + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +//connect message when communication with monitoring broken +//#define FARM_CONNECT_MESSAGE + +/*----------------------------------- + PREHEAT SETTINGS + *------------------------------------*/ + +#define FARM_PREHEAT_HOTEND_TEMP 250 +#define FARM_PREHEAT_HPB_TEMP 60 +#define FARM_PREHEAT_FAN_SPEED 0 + +#define PLA_PREHEAT_HOTEND_TEMP 215 +#define PLA_PREHEAT_HPB_TEMP 60 +#define PLA_PREHEAT_FAN_SPEED 0 + +#define ABS_PREHEAT_HOTEND_TEMP 255 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 0 + +#define HIPS_PREHEAT_HOTEND_TEMP 220 +#define HIPS_PREHEAT_HPB_TEMP 100 +#define HIPS_PREHEAT_FAN_SPEED 0 + +#define PP_PREHEAT_HOTEND_TEMP 254 +#define PP_PREHEAT_HPB_TEMP 100 +#define PP_PREHEAT_FAN_SPEED 0 + +#define PET_PREHEAT_HOTEND_TEMP 230 +#define PET_PREHEAT_HPB_TEMP 85 +#define PET_PREHEAT_FAN_SPEED 0 + +#define FLEX_PREHEAT_HOTEND_TEMP 240 +#define FLEX_PREHEAT_HPB_TEMP 50 +#define FLEX_PREHEAT_FAN_SPEED 0 + +/*------------------------------------ + THERMISTORS SETTINGS + *------------------------------------*/ + +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a +// 247 is Pt100 with 4k7 pullup and PT100 Amplifier +// 110 is Pt100 with 1k pullup (non standard) + +#if defined(E3D_PT100_EXTRUDER_WITH_AMP) +#define TEMP_SENSOR_0 247 +#elif defined(E3D_PT100_EXTRUDER_NO_AMP) +#define TEMP_SENSOR_0 148 +#else +#define TEMP_SENSOR_0 5 +#endif +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#if defined(E3D_PT100_BED_WITH_AMP) +#define TEMP_SENSOR_BED 247 +#elif defined(E3D_PT100_BED_NO_AMP) +#define TEMP_SENSOR_BED 148 +#else +#define TEMP_SENSOR_BED 1 +#endif +#define TEMP_SENSOR_PINDA 1 +#define TEMP_SENSOR_AMBIENT 2000 + +#define STACK_GUARD_TEST_VALUE 0xA2A2 + +#define MAX_BED_TEMP_CALIBRATION 50 +#define MAX_HOTEND_TEMP_CALIBRATION 50 + +#define MAX_E_STEPS_PER_UNIT 250 +#define MIN_E_STEPS_PER_UNIT 100 + +#define Z_BABYSTEP_MIN -3999 +#define Z_BABYSTEP_MAX 0 + +#define PINDA_PREHEAT_X 20 +#define PINDA_PREHEAT_Y 60 +#define PINDA_PREHEAT_Z 0.15 +/* +#define PINDA_PREHEAT_X 70 +#define PINDA_PREHEAT_Y -3 +#define PINDA_PREHEAT_Z 1*/ +#define PINDA_HEAT_T 120 //time in s + +#define PINDA_MIN_T 50 +#define PINDA_STEP_T 10 +#define PINDA_MAX_T 100 + +#define PING_TIME 60 //time in s +#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes +#define PING_ALLERT_PERIOD 60 //time in s + +#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring +#define NC_BUTTON_LONG_PRESS 15 //time in s + +#define LONG_PRESS_TIME 1000 //time in ms for button long press +#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release + +#define DEFAULT_PID_TEMP 210 + +#define MIN_PRINT_FAN_SPEED 75 + + +// How much shall the print head be lifted on power panic? +// Ideally the Z axis will reach a zero phase of the stepper driver on power outage. To simplify this, +// UVLO_Z_AXIS_SHIFT shall be an integer multiply of the stepper driver cycle, that is 4x full step. +// For example, the Prusa i3 MK2 with 16 microsteps per full step has Z stepping of 400 microsteps per mm. +// At 400 microsteps per mm, a full step lifts the Z axis by 0.04mm, and a stepper driver cycle is 0.16mm. +// The following example, 12 * (4 * 16 / 400) = 12 * 0.16mm = 1.92mm. +//#define UVLO_Z_AXIS_SHIFT 1.92 +#define UVLO_Z_AXIS_SHIFT 0.64 +// If power panic occured, and the current temperature is higher then target temperature before interrupt minus this offset, print will be recovered automatically. +#define AUTOMATIC_UVLO_BED_TEMP_OFFSET 5 + +#define HEATBED_V2 + +#define M600_TIMEOUT 600 //seconds + +//#define SUPPORT_VERBOSITY + +#define MMU_REQUIRED_FW_BUILDNR 83 +#define MMU_HWRESET +#define MMU_DEBUG //print communication between MMU2 and printer on serial +#define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning + +#endif //__CONFIGURATION_PRUSA_H From 63c8a361853c45ad98c10dd4faf5fa4b38d632b7 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 16:27:44 +0100 Subject: [PATCH 02/11] typo fixed --- Firmware/ultralcd.cpp | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Firmware/ultralcd.cpp b/Firmware/ultralcd.cpp index 16b077da..b26b1c96 100644 --- a/Firmware/ultralcd.cpp +++ b/Firmware/ultralcd.cpp @@ -181,9 +181,9 @@ enum class testScreen static int lcd_selftest_screen(testScreen screen, int _progress, int _progress_scale, bool _clear, int _delay); static void lcd_selftest_screen_step(int _row, int _col, int _state, const char *_name, const char *_indicator); static bool lcd_selftest_manual_fan_check(int _fan, bool check_opposite); -#ifdef FAN_CHECK +#ifdef FANCHECK static bool lcd_selftest_fan_dialog(int _fan); -#endif //FAN_CHECk +#endif //FANCHECK static bool lcd_selftest_fsensor(); static bool selftest_irsensor(); static void lcd_selftest_error(int _error_no, const char *_error_1, const char *_error_2); From de9c87c5925bf53e3f1f1dab43b0e53489dcf295 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 19:38:52 +0100 Subject: [PATCH 03/11] welcome message changed --- Firmware/messages.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Firmware/messages.c b/Firmware/messages.c index 4cac4f2d..7943d220 100644 --- a/Firmware/messages.c +++ b/Firmware/messages.c @@ -96,7 +96,7 @@ const char MSG_WIZARD_DONE[] PROGMEM_I1 = ISTR("All is done. Happy printing!"); const char MSG_WIZARD_HEATING[] PROGMEM_I1 = ISTR("Preheating nozzle. Please wait."); ////c=20 r=3 const char MSG_WIZARD_QUIT[] PROGMEM_I1 = ISTR("You can always resume the Wizard from Calibration -> Wizard."); ////c=20 r=8 const char MSG_YES[] PROGMEM_I1 = ISTR("Yes"); ////c=0 r=0 -const char WELCOME_MSG[] PROGMEM_I1 = ISTR(CUSTOM_MENDEL_NAME " ready."); ////c=20 r=0 +const char WELCOME_MSG[] PROGMEM_I1 = ISTR(CUSTOM_MENDEL_NAME " OK."); ////c=20 r=0 //not internationalized messages const char MSG_SD_WORKDIR_FAIL[] PROGMEM_N1 = "workDir open failed"; ////c=0 r=0 const char MSG_BROWNOUT_RESET[] PROGMEM_N1 = " Brown out Reset"; ////c=0 r=0 From a85d8e7f97863c992cec6695998e4861619d7fe7 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 21:36:21 +0100 Subject: [PATCH 04/11] message change --- Firmware/ultralcd.cpp | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Firmware/ultralcd.cpp b/Firmware/ultralcd.cpp index b26b1c96..8c2b5281 100644 --- a/Firmware/ultralcd.cpp +++ b/Firmware/ultralcd.cpp @@ -2264,7 +2264,7 @@ static void lcd_support_menu() MENU_ITEM_BACK_P(STR_SEPARATOR); MENU_ITEM_SUBMENU_P(_i("XYZ cal. details"), lcd_menu_xyz_y_min);////MSG_XYZ_DETAILS c=19 r=1 MENU_ITEM_SUBMENU_P(_i("Extruder info"), lcd_menu_extruder_info);////MSG_INFO_EXTRUDER c=18 r=1 - MENU_ITEM_SUBMENU_P(_i("Sensors info"), lcd_menu_show_sensors_state);////MSG_INFO_SENSORS c=18 r=1 + MENU_ITEM_SUBMENU_P(_i("Sensor info"), lcd_menu_show_sensors_state);////MSG_INFO_SENSORS c=18 r=1 #ifdef TMC2130 MENU_ITEM_SUBMENU_P(_i("Belt status"), lcd_menu_belt_status);////MSG_MENU_BELT_STATUS c=18 r=1 From ff52499bdc9839936e81fc0ea35b81c466953f9d Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 22:56:10 +0100 Subject: [PATCH 05/11] extr fan RPM measuring fix --- Firmware/temperature.cpp | 7 +++++++ Firmware/ultralcd.cpp | 8 +++----- 2 files changed, 10 insertions(+), 5 deletions(-) diff --git a/Firmware/temperature.cpp b/Firmware/temperature.cpp index 8dcfc9a9..e156734b 100644 --- a/Firmware/temperature.cpp +++ b/Firmware/temperature.cpp @@ -2070,10 +2070,17 @@ else { // ambient temperature is stan #if (defined(FANCHECK) && defined(TACH_0) && (TACH_0 > -1)) void check_fans() { +#ifdef FAN_SOFT_PWM + if (READ(TACH_0) != fan_state[0]) { + if(fan_measuring) fan_edge_counter[0] ++; + fan_state[0] = !fan_state[0]; + } +#else //FAN_SOFT_PWM if (READ(TACH_0) != fan_state[0]) { fan_edge_counter[0] ++; fan_state[0] = !fan_state[0]; } +#endif //if (READ(TACH_1) != fan_state[1]) { // fan_edge_counter[1] ++; // fan_state[1] = !fan_state[1]; diff --git a/Firmware/ultralcd.cpp b/Firmware/ultralcd.cpp index 8c2b5281..9614c9a4 100644 --- a/Firmware/ultralcd.cpp +++ b/Firmware/ultralcd.cpp @@ -7352,15 +7352,13 @@ static bool lcd_selftest_fan_dialog(int _fan) setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, 1); //extruder fan #ifdef FAN_SOFT_PWM extruder_autofan_last_check = _millis(); + fan_measuring = true; #endif //FAN_SOFT_PWM _delay(2000); //delay_keep_alive would turn off extruder fan, because temerature is too low -#ifdef FAN_SOFT_PWM - countFanSpeed(); - if (!fan_speed[0]) _result = false; -#else //FAN_SOFT_PWM + manage_heater(); //count average fan speed from 2s delay and turn off fans if (!fan_speed[0]) _result = false; -#endif //FAN_SOFT_PWM + printf_P(PSTR("Test 1:\n")); printf_P(PSTR("Print fan speed: %d \n"), fan_speed[1]); From e028db7bf906fbc2707569168d758acf41676066 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 23:30:01 +0100 Subject: [PATCH 06/11] version change --- Firmware/Configuration.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h index 37b7f6be..48b99140 100644 --- a/Firmware/Configuration.h +++ b/Firmware/Configuration.h @@ -7,13 +7,13 @@ #define STR(x) STR_HELPER(x) // Firmware version -#define FW_VERSION "3.5.1" -#define FW_COMMIT_NR 1778 +#define FW_VERSION "3.5.3" +#define FW_COMMIT_NR 1971 // FW_VERSION_UNKNOWN means this is an unofficial build. // The firmware should only be checked into github with this symbol. #define FW_DEV_VERSION FW_VERSION_UNKNOWN #define FW_REPOSITORY "Unknown" -#define FW_VERSION_FULL FW_VERSION "-" STR(FW_COMMIT_NR) +#define FW_VERSION_FULL FW_VERSION //"-" STR(FW_COMMIT_NR) // Debug version has debugging enabled (the symbol DEBUG_BUILD is set). // The debug build may be a bit slower than the non-debug build, therefore the debug build should From 38b0e5439b910c21d45cdd78e9a8ee1b757dea26 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 23:52:24 +0100 Subject: [PATCH 07/11] version change --- Firmware/Configuration.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h index 48b99140..ee7c1e93 100644 --- a/Firmware/Configuration.h +++ b/Firmware/Configuration.h @@ -8,12 +8,12 @@ // Firmware version #define FW_VERSION "3.5.3" -#define FW_COMMIT_NR 1971 +#define FW_COMMIT_NR 1990 // FW_VERSION_UNKNOWN means this is an unofficial build. // The firmware should only be checked into github with this symbol. -#define FW_DEV_VERSION FW_VERSION_UNKNOWN +#define FW_DEV_VERSION FW_VERSION_GOLD #define FW_REPOSITORY "Unknown" -#define FW_VERSION_FULL FW_VERSION //"-" STR(FW_COMMIT_NR) +#define FW_VERSION_FULL FW_VERSION "-" STR(FW_COMMIT_NR) // Debug version has debugging enabled (the symbol DEBUG_BUILD is set). // The debug build may be a bit slower than the non-debug build, therefore the debug build should From 065d56b2c6404ab2280f83e8b9088f1675e908ff Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Wed, 6 Feb 2019 23:58:30 +0100 Subject: [PATCH 08/11] version change --- Firmware/Configuration.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h index ee7c1e93..9b00b796 100644 --- a/Firmware/Configuration.h +++ b/Firmware/Configuration.h @@ -13,7 +13,7 @@ // The firmware should only be checked into github with this symbol. #define FW_DEV_VERSION FW_VERSION_GOLD #define FW_REPOSITORY "Unknown" -#define FW_VERSION_FULL FW_VERSION "-" STR(FW_COMMIT_NR) +#define FW_VERSION_FULL FW_VERSION // "-" STR(FW_COMMIT_NR) // Debug version has debugging enabled (the symbol DEBUG_BUILD is set). // The debug build may be a bit slower than the non-debug build, therefore the debug build should From ccc542d74aa3c0c662e31e14ead796014507255d Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Mon, 11 Feb 2019 14:32:21 +0100 Subject: [PATCH 09/11] MK2.5 IR_SENSOR_PIN modified --- Firmware/pins_Rambo_1_0.h | 2 +- Firmware/pins_Rambo_1_3.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/Firmware/pins_Rambo_1_0.h b/Firmware/pins_Rambo_1_0.h index b973fd30..bb6eb026 100644 --- a/Firmware/pins_Rambo_1_0.h +++ b/Firmware/pins_Rambo_1_0.h @@ -102,7 +102,7 @@ #define SDCARDDETECT 72 -#define IR_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8) +#define IR_SENSOR_PIN 20 //idler sensor // Support for an 8 bit logic analyzer, for example the Saleae. // Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop. diff --git a/Firmware/pins_Rambo_1_3.h b/Firmware/pins_Rambo_1_3.h index d684519e..c1adf596 100644 --- a/Firmware/pins_Rambo_1_3.h +++ b/Firmware/pins_Rambo_1_3.h @@ -102,7 +102,7 @@ #define SDCARDDETECT 15 -#define IR_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8) +#define IR_SENSOR_PIN 20 //idler sensor // Support for an 8 bit logic analyzer, for example the Saleae. // Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop. From b85661309feb4b1e0405e95d2598b1a4755771cc Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Mon, 11 Feb 2019 16:38:36 +0100 Subject: [PATCH 10/11] configuration change --- Firmware/Configuration.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h index 9b00b796..2a33e941 100644 --- a/Firmware/Configuration.h +++ b/Firmware/Configuration.h @@ -11,7 +11,7 @@ #define FW_COMMIT_NR 1990 // FW_VERSION_UNKNOWN means this is an unofficial build. // The firmware should only be checked into github with this symbol. -#define FW_DEV_VERSION FW_VERSION_GOLD +#define FW_DEV_VERSION FW_VERSION_UNKNOWN #define FW_REPOSITORY "Unknown" #define FW_VERSION_FULL FW_VERSION // "-" STR(FW_COMMIT_NR) From 4c7639323194f33d606516cf38c3f7a90a41c927 Mon Sep 17 00:00:00 2001 From: PavelSindler Date: Tue, 12 Feb 2019 13:44:50 +0100 Subject: [PATCH 11/11] version change --- Firmware/Configuration.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h index 2a33e941..14104521 100644 --- a/Firmware/Configuration.h +++ b/Firmware/Configuration.h @@ -8,7 +8,7 @@ // Firmware version #define FW_VERSION "3.5.3" -#define FW_COMMIT_NR 1990 +#define FW_COMMIT_NR 2007 // FW_VERSION_UNKNOWN means this is an unofficial build. // The firmware should only be checked into github with this symbol. #define FW_DEV_VERSION FW_VERSION_UNKNOWN