3DPrinting/Prusa-Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

initial version which works on old and new hw, initial version of idler sensor detection

Browse Source
This commit is contained in:
PavelSindler 2018-12-21 17:12:16 +01:00
parent 880163dbcb
commit 3c64bad1cb
7 changed files with 91 additions and 74 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

74
Firmware/mmu.cpp
View File

@ -38,9 +38,10 @@ static int8_t mmu_state = 0;
uint8_t mmu_cmd = 0;
#ifdef MMU_IDLER_SENSOR_PIN
//idler ir sensor
uint8_t mmu_idl_sens = 0;
#endif //MMU_IDLER_SENSOR_PIN
bool mmu_idler_sensor_detected = false;
uint8_t mmu_extruder = MMU_FILAMENT_UNKNOWN;
@ -111,10 +112,25 @@ void mmu_init(void)
_delay_ms(10); //wait 10ms for sure
mmu_reset(); //reset mmu (HW or SW), do not wait for response
mmu_state = -1;
#ifdef MMU_IDLER_SENSOR_PIN
PIN_INP(MMU_IDLER_SENSOR_PIN); //input mode
PIN_SET(MMU_IDLER_SENSOR_PIN); //pullup
#endif //MMU_IDLER_SENSOR_PIN
}
//returns true if idler IR sensor was detected, otherwise returns false
bool check_for_idler_sensor()
{
bool detected = false;
//if MMU_IDLER_SENSOR_PIN input is low and pat9125sensor is not present we detected idler sensor
if ((PIN_GET(MMU_IDLER_SENSOR_PIN) == 0) && fsensor_not_responding)
{
detected = true;
//printf_P(PSTR("Idler IR sensor detected\n"));
}
else
{
//printf_P(PSTR("Idler IR sensor not detected\n"));
}
return detected;
}
//mmu main loop - state machine processing
@ -167,9 +183,9 @@ void mmu_loop(void)
if ((PRINTER_TYPE == PRINTER_MK3) || (PRINTER_TYPE == PRINTER_MK3_SNMM))
{
#ifdef MMU_DEBUG
#if defined MMU_DEBUG && defined MMU_FINDA_DEBUG
puts_P(PSTR("MMU <= 'P0'"));
#endif //MMU_DEBUG
#endif //MMU_DEBUG && MMU_FINDA_DEBUG
mmu_puts_P(PSTR("P0\n")); //send 'read finda' request
mmu_state = -4;
}
@ -187,9 +203,9 @@ void mmu_loop(void)
case -5:
if (mmu_rx_ok() > 0)
{
#ifdef MMU_DEBUG
#if defined MMU_DEBUG && defined MMU_FINDA_DEBUG
puts_P(PSTR("MMU <= 'P0'"));
#endif //MMU_DEBUG
#endif //MMU_DEBUG && MMU_FINDA_DEBUG
mmu_puts_P(PSTR("P0\n")); //send 'read finda' request
mmu_state = -4;
}
@ -198,11 +214,13 @@ void mmu_loop(void)
if (mmu_rx_ok() > 0)
{
fscanf_P(uart2io, PSTR("%hhu"), &mmu_finda); //scan finda from buffer
#ifdef MMU_DEBUG
#if defined MMU_DEBUG && defined MMU_FINDA_DEBUG
printf_P(PSTR("MMU => '%dok'\n"), mmu_finda);
#endif //MMU_DEBUG
#endif //MMU_DEBUG && MMU_FINDA_DEBUG
puts_P(PSTR("MMU - ENABLED"));
mmu_enabled = true;
//if we have filament loaded into the nozzle, we can decide if printer has idler sensor right now; otherwise we will will wait till start of T-code so it will be detected on beginning of second T-code
if(check_for_idler_sensor()) mmu_idler_sensor_detected = true;
mmu_state = 1;
}
return;
@ -218,9 +236,7 @@ void mmu_loop(void)
mmu_printf_P(PSTR("T%d\n"), filament);
mmu_state = 3; // wait for response
mmu_fil_loaded = true;
#ifdef MMU_IDLER_SENSOR_PIN
mmu_idl_sens = 1; //enable idler sensor
#endif //MMU_IDLER_SENSOR_PIN
if(mmu_idler_sensor_detected) mmu_idl_sens = 1; //if idler sensor detected, use it for T-code
}
else if ((mmu_cmd >= MMU_CMD_L0) && (mmu_cmd <= MMU_CMD_L4))
{
@ -238,9 +254,7 @@ void mmu_loop(void)
#endif //MMU_DEBUG
mmu_puts_P(PSTR("C0\n")); //send 'continue loading'
mmu_state = 3;
#ifdef MMU_IDLER_SENSOR_PIN
mmu_idl_sens = 1; //enable idler sensor
#endif //MMU_IDLER_SENSOR_PIN
if(mmu_idler_sensor_detected) mmu_idl_sens = 1; //if idler sensor detected use it for C0 code
}
else if (mmu_cmd == MMU_CMD_U0)
{
@ -273,9 +287,10 @@ void mmu_loop(void)
}
else if ((mmu_last_response + 300) < millis()) //request every 300ms
{
#ifdef MMU_DEBUG
if(check_for_idler_sensor()) mmu_idler_sensor_detected = true;
#if defined MMU_DEBUG && defined MMU_FINDA_DEBUG
puts_P(PSTR("MMU <= 'P0'"));
#endif //MMU_DEBUG
#endif //MMU_DEBUG && MMU_FINDA_DEBUG
mmu_puts_P(PSTR("P0\n")); //send 'read finda' request
mmu_state = 2;
}
@ -284,9 +299,9 @@ void mmu_loop(void)
if (mmu_rx_ok() > 0)
{
fscanf_P(uart2io, PSTR("%hhu"), &mmu_finda); //scan finda from buffer
#ifdef MMU_DEBUG
#if defined MMU_DEBUG && MMU_FINDA_DEBUG
printf_P(PSTR("MMU => '%dok'\n"), mmu_finda);
#endif //MMU_DEBUG
#endif //MMU_DEBUG && MMU_FINDA_DEBUG
//printf_P(PSTR("Eact: %d\n"), int(e_active()));
if (!mmu_finda && CHECK_FINDA && fsensor_enabled) {
fsensor_stop_and_save_print();
@ -304,7 +319,7 @@ void mmu_loop(void)
}
return;
case 3: //response to mmu commands
#ifdef MMU_IDLER_SENSOR_PIN
if (mmu_idler_sensor_detected) {
if (mmu_idl_sens)
{
if (PIN_GET(MMU_IDLER_SENSOR_PIN) == 0)
@ -319,7 +334,7 @@ void mmu_loop(void)
//else
//printf_P(PSTR("MMU IDLER_SENSOR = 1 - WAIT\n"));
}
#endif //MMU_IDLER_SENSOR_PIN
}
if (mmu_rx_ok() > 0)
{
#ifdef MMU_DEBUG
@ -379,6 +394,8 @@ void mmu_load_step() {
}
bool mmu_get_response(uint8_t move)
{
if (!mmu_idler_sensor_detected) move = MMU_NO_MOVE;
printf_P(PSTR("mmu_get_response - begin move:%d\n"), move);
KEEPALIVE_STATE(IN_PROCESS);
while (mmu_cmd != 0)
@ -399,7 +416,6 @@ bool mmu_get_response(uint8_t move)
mmu_load_step();
break;
case MMU_UNLOAD_MOVE:
#ifdef MMU_IDLER_SENSOR_PIN
if (PIN_GET(MMU_IDLER_SENSOR_PIN) == 0) //filament is still detected by idler sensor, printer helps with unlading
{
printf_P(PSTR("Unload 1\n"));
@ -408,7 +424,6 @@ bool mmu_get_response(uint8_t move)
st_synchronize();
}
else //filament was unloaded from idler, no additional movements needed
#endif //MMU_IDLER_SENSOR_PIN
{
printf_P(PSTR("Unloading finished 1\n"));
disable_e0(); //turn off E-stepper to prevent overheating and alow filament pull-out if necessary
@ -417,7 +432,6 @@ bool mmu_get_response(uint8_t move)
break;
case MMU_TCODE_MOVE: //first do unload and then continue with infinite loading movements
#ifdef MMU_IDLER_SENSOR_PIN
if (PIN_GET(MMU_IDLER_SENSOR_PIN) == 0) //filament detected by idler sensor, we must unload first
{
printf_P(PSTR("Unload 2\n"));
@ -426,7 +440,6 @@ bool mmu_get_response(uint8_t move)
st_synchronize();
}
else //delay to allow mmu unit to pull out filament from bondtech gears and then start with infinite loading
#endif //MMU_IDLER_SENSOR_PIN
{
printf_P(PSTR("Unloading finished 2\n"));
disable_e0(); //turn off E-stepper to prevent overheating and alow filament pull-out if necessary
@ -1243,9 +1256,9 @@ void mmu_eject_filament(uint8_t filament, bool recover)
void mmu_continue_loading()
{
#ifdef MMU_IDLER_SENSOR_PIN
for (uint8_t i = 0; i < MMU_IDLER_SENSOR_ATTEMPTS_NR; i++) {
if (mmu_idler_sensor_detected) {
for (uint8_t i = 0; i < MMU_IDLER_SENSOR_ATTEMPTS_NR; i++) {
if (PIN_GET(MMU_IDLER_SENSOR_PIN) == 0) return;
#ifdef MMU_DEBUG
printf_P(PSTR("Additional load attempt nr. %d\n"), i);
@ -1277,7 +1290,8 @@ void mmu_continue_loading()
mmu_fil_loaded = false; //so we can retry same T-code again
restore_print_from_ram_and_continue(0);
}
#else
}
else { //mmu_idler_sensor_detected == false
mmu_command(MMU_CMD_C0);
#endif //MMU_IDLER_SENSOR_PIN
}
}

2
Firmware/mmu.h
View File

@ -11,6 +11,7 @@ extern uint8_t mmu_extruder;
extern uint8_t tmp_extruder;
extern int8_t mmu_finda;
extern bool mmu_idler_sensor_detected;
extern int16_t mmu_version;
extern int16_t mmu_buildnr;
@ -52,6 +53,7 @@ extern int mmu_printf_P(const char* format, ...);
extern int8_t mmu_rx_ok(void);
extern bool check_for_idler_sensor();
extern void mmu_init(void);

1
Firmware/pins_Einsy_1_0.h
View File

@ -121,6 +121,7 @@
#define TACH_0 79 // !!! changed from 81 (EINY03)
#define TACH_1 80
#define MMU_IDLER_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8)
// Support for an 8 bit logic analyzer, for example the Saleae.
// Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop.

2
Firmware/pins_Rambo_1_0.h
View File

@ -102,7 +102,7 @@
#define SDCARDDETECT 72
#define MMU_IDLER_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8)
// Support for an 8 bit logic analyzer, for example the Saleae.
// Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop.

2
Firmware/pins_Rambo_1_3.h
View File

@ -102,7 +102,7 @@
#define SDCARDDETECT 15
#define MMU_IDLER_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8)
// Support for an 8 bit logic analyzer, for example the Saleae.
// Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop.

4
Firmware/ultralcd.cpp
View File

@ -3653,9 +3653,9 @@ static void lcd_show_sensors_state()
if (mmu_enabled) {
finda_state = mmu_finda;
}
#ifdef MMU_IDLER_SENSOR_PIN
if (mmu_idler_sensor_detected) {
idler_state = !PIN_GET(MMU_IDLER_SENSOR_PIN);
#endif
}
lcd_puts_at_P(0, 0, _i("Sensors state"));
lcd_puts_at_P(1, 1, _i("PINDA:"));
lcd_set_cursor(LCD_WIDTH - 4, 1);

2
Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h
View File

@ -614,7 +614,7 @@
#define MMU_REQUIRED_FW_BUILDNR 83
#define MMU_HWRESET
//#define MMU_DEBUG //print communication between MMU2 and printer on serial
#define MMU_IDLER_SENSOR_PIN 62 //idler sensor @PK0 (digital pin 62/A8)
#define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning
#endif //__CONFIGURATION_PRUSA_H